AD AD5227BUJZ100-RL7

64-Position Up/Down
Control Digital Potentiometer
AD5227
FEATURES
FUNCTIONAL BLOCK DIAGRAM
64-position digital potentiometer
10 kΩ, 50 kΩ, 100 kΩ end-to-end terminal resistance
Simple up/down digital or manual configurable control
Midscale preset
Low potentiometer mode tempco = 10 ppm/°C
Low rheostat mode tempco = 35 ppm/°C
Ultralow power, IDD = 0.4 μA typ and 3 μA max
Fast adjustment time, ts = 1 μs
Chip select enable multiple device operation
Low operating voltage, 2.7 V to 5.5 V
Automotive temperature range, −40°C to +105°C
Compact thin SOT-23-8 (2.9 mm × 3 mm) Pb-free package
VDD
AD5227
A
CS
6-BIT UP/DOWN
CONTROL
LOGIC
U/D
CLK
W
B
POR
MIDSCALE
WIPER
REGISTER
04419-0-001
GND
Figure 1.
APPLICATIONS
Mechanical potentiometer and trimmer replacements
LCD backlight, contrast, and brightness controls
Portable electronics level adjustment
Programmable power supply
Digital trimmer replacements
Automatic closed-loop control
GENERAL DESCRIPTION
The AD5227 is Analog Devices’ latest 64-step up/down control
digital potentiometer1. This device performs the same electronic
adjustment function as a 5 V potentiometer or variable resistor.
Its simple 3-wire up/down interface allows manual switching or
high speed digital control. The AD5227 presets to midscale at
power-up. When CS is enabled, the devices changes step at
every clock pulse. The direction is determined by the state of
the U/D pin (see Table 1). The interface is simple to activate by
any host controller, discrete logic, or manually with a rotary
encoder or pushbuttons. The AD5227’s 64-step resolution, small
footprint, and simple interface enable it to replace mechanical
potentiometers and trimmers with typically 6× improved
resolution, solid-state reliability, and design layout flexibility,
resulting in a considerable cost savings in end users’ systems.
1
The AD5227 is available in a compact thin SOT-23-8 (TSOT-8)
Pb-free package. The part is guaranteed to operate over the
automotive temperature range of −40°C to +105°C.
Users who consider EEMEM potentiometers should refer to
some recommendations in the Applications section.
Table 1. Truth Table
CS
0
0
1
1
CLK
↓
↓
X
U/D
0
1
X
Operation 1
RWB Decrement
RWB Increment
No Operation
RWA increments if RWB decrements and vice versa.
The terms digital potentiometer and RDAC are used interchangeably.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703© 2004–2009 Analog Devices, Inc. All rights reserved.
AD5227
TABLE OF CONTENTS
Electrical Characteristics ................................................................. 3 Applications..................................................................................... 12 Interface Timing Diagrams ......................................................... 4 Manual Control with Toggle and Pushbutton Switches ........ 12 Absolute Maximum Ratings............................................................ 5 Manual Control with Rotary Encoder..................................... 12 ESD Caution .................................................................................. 5 Adjustable LED Driver .............................................................. 12 Pin Configuration and Function Descriptions ............................. 6 Adjustable Current Source for LED Driver ............................ 12 Typical Performance Characteristics ............................................. 7 Adjustable High Power LED Driver ........................................ 13 Theory of Operation ...................................................................... 10 Automatic LCD Panel Backlight Control................................ 13 Programming the Digital Potentiometers ............................... 10 6-Bit Controller .......................................................................... 13 Digital Interface .......................................................................... 11 Constant Bias with Supply to Retain Resistance Setting ....... 14 Terminal Voltage Operation Range ......................................... 11 Outline Dimensions ....................................................................... 15 Power-Up and Power-Down Sequences .................................. 11 Ordering Guide .......................................................................... 15 Layout and Power Supply Biasing ............................................ 11 REVISION HISTORY
5/09—Rev. A to Rev. B
Changes to Table 2……………………………………………3
4/09—Rev. 0 to Rev. A
Changes to Table 2……………………………………………3
Changes to Ordering Guide …………………………………15
3/04—Revision 0: Initial Version
Rev. B | Page 2 of 16
AD5227
ELECTRICAL CHARACTERISTICS
10 kΩ, 50 kΩ, 100 kΩ versions: VDD = 3 V ± 10% or 5 V ± 10%, VA = VDD, VB = 0 V, −40°C < TA < +105°C, unless otherwise noted.
Table 2.
Parameter
DC CHARACTERISTICS RHEOSTAT MODE
Resistor Differential Nonlinearity 2
Resistor Integral Nonlinearity2
Nominal Resistor Tolerance 3
Resistance Temperature Coefficient
Wiper Resistance
Symbol
Conditions
Min
Typ 1
Max
Unit
R-DNL
R-INL
∆RAB/RAB
(∆RAB/RAB)/∆T × 106
RW
RWB, A = no connect
RWB, A = no connect
−0.5
−1
−20
±0.15
±0.3
+0.5
+1
+20
LSB
LSB
%
ppm/°C
Ω
Ω
DC CHARACTERISTICS POTENTIOMETER DIVIDER MODE
Resolution
N
Integral Nonlinearity3
INL
Differential Nonlinearity3, 4
DNL
Voltage Divider Temperature Coefficient
(∆VW/VW)/∆T × 106
Full-Scale Error
VWFSE
Zero-Scale Error
VWZSE
RESISTOR TERMINALS
Voltage Range 5
Capacitance A, B 6
VA, B, W
CA, B
Capacitance W6
Common-Mode Leakage
DIGITAL INPUTS (CS, CLK, U/D)
Input Logic High
Input Logic Low
Input Current
Input Capacitance6
POWER SUPPLIES
Power Supply Range
Supply Current
Power Dissipation 7
Power Supply Sensitivity
DYNAMIC CHARACTERISTICS6, 8, 9
Bandwidth −3 dB
CW
ICM
VIH
VIL
II
CI
VDD
IDD
PDISS
PSSR
Total Harmonic Distortion
BW_10 k
BW_50 k
BW_100 k
THD
Adjustment Settling Time
tS
Resistor Noise Voltage
eN_WB
35
100
50
VDD = 2.7 V
VDD = 2.8 V to 5.5 V
−1
−0.5
Midscale
≥+31 steps from midscale
−40°C < TA < +60°C,
VDD = 2.8 V to 5.5 V
≤−32 steps from midscale
−40°C < TA < +60°C,
VDD = 2.8 V to 5.5 V
With respect to GND
f = 1 MHz, measured to
GND
f = 1 MHz, measured to
GND
VA = VB = VW
250
200
0
0
Bits
LSB
LSB
ppm/°C
LSB
LSB
1.2
1
LSB
LSB
VDD
140
V
pF
150
pF
1
nA
−1.2
−1
±0.1
±0.1
5
−0.5
−0.5
0
0
0.5
0.5
0
2.4
0
VIN = 0 V or 5 V
6
+1
+0.5
5.5
0.8
±1
V
V
μA
pF
5.5
3
V
μA
17
μW
0.05
%/%
5
2.7
VIH = 5 V or VIL = 0 V,
VDD = 5 V
VIH = 5 V or VIL = 0 V,
VDD = 5 V
VDD = 5 V ± 10%
0.4
RAB = 10 kΩ, midscale
RAB = 50 kΩ, midscale
RAB = 100 kΩ, midscale
VA = 1 V rms, RAB = 10 kΩ,
VB = 0 V dc, f = 1 kHz
VA = 5 V ± 1 LSB error
band, VB = 0, measured at
VW
RWB = 5 kΩ, f = 1 kHz
460
100
50
0.05
kHz
kHz
kHz
%
1
μs
14
nV/√Hz
Footnotes on the next page.
Rev. B | Page 3 of 16
0.01
AD5227
Parameter
Symbol
INTERFACE TIMING CHARACTERISTICS (applies to all parts6, 10 )
Clock Frequency
fCLK
Input Clock Pulse Width
tCH, tCL
tCSS
CS to CLK Setup Time
tCSH
CS Rise to CLK Hold Time
tUDS
U/D to Clock Fall Setup Time
Conditions
Min
Clock level high or low
10
10
10
10
1
Typ 1
Max
Unit
50
MHz
ns
ns
ns
ns
Typicals represent average readings at 25°C, VDD = 5 V.
Resistor position nonlinearity error, R-INL, is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic.
3
NL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. VA = VDD and VB = 0 V.
4
DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions.
5
Resistor Terminals A, B, W have no limitations on polarity with respect to each other.
6
Guaranteed by design and not subject to production test.
7
PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation.
8
Bandwidth, noise, and settling time are dependent on the terminal resistance value chosen. The lowest R value results in the fastest settling time and highest
bandwidth. The highest R value results in the minimum overall power consumption.
9
All dynamic characteristics use VDD = V.
10
All input control voltages are specified with tR = tF = 1 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V. Switching characteristics are measured using
VDD = 5 V.
2
INTERFACE TIMING DIAGRAMS
CS = LOW
U/D = HIGH
04419-0-004
CLK
RWB
Figure 2. Increment RWB
CS = LOW
U/D = 0
CLK
04419-0-005
RWB
Figure 3. Decrement RWB
1
CS
0
tCSS
tCH
tCSH
tCL
1
CLK
0
tUDS
1
U/D
0
04419-0-006
tS
RWB
Figure 4. Detailed Timing Diagram (Only RWB Decrement Shown)
Rev. B | Page 4 of 16
AD5227
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
VDD to GND
VA, VB, VW to GND
Digital Input Voltage to GND (CS, CLK, U/D)
Maximum Current
IWB, IWA Pulsed
IWB Continuous (RWB ≤ 5 kΩ, A open) 1
IWA Continuous (RWA ≤ 5 kΩ, B open)1
IAB Continuous
(RAB = 10 kΩ/50 kΩ/100 kΩ)1
Operating Temperature Range
Maximum Junction Temperature (TJmax)
Storage Temperature
Lead Temperature (Soldering, 10 s – 30 s)
Thermal Resistance 2 θJA
Rating
−0.3 V, +7 V
0 V, VDD
0 V, VDD
±20 mA
±1 mA
±1 mA
±500 μA/
±100 μA/±50 μA
−40°C to +105°C
150°C
−65°C to +150°C
245°C
230°C/W
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
1
Maximum terminal current is bounded by the maximum applied voltage
across any two of the A, B, and W terminals at a given resistance, the
maximum current handling of the switches, and the maximum power
dissipation of the package. VDD = 5 V.
2
Package power dissipation = (TJmax – TA) / θJA.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 5 of 16
AD5227
CLK 1
U/D 2
AD5227
TOP VIEW
A 3 (Not to Scale)
GND 4
8
VDD
7
CS
6
B
5
W
04419-0-003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 5. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
CLK
2
3
4
5
6
7
8
U/D
A
GND
W
B
CS
VDD
Description
Clock Input. Each clock pulse executes the step-up or step-down of the resistance. The direction is determined
by the state of the U/D pin. CLK is a negative-edge trigger. Logic high signal can be higher than VDD, but lower
than 5.5 V.
Up/Down Selections. Logic 1 selects up and Logic 0 selects down. U can be higher than VDD, but lower than 5.5 V.
Resistor Terminal A. GND ≤ VA ≤ VDD.
Common Ground.
Wiper Terminal W. GND ≤ VW ≤ VDD.
Resistor Terminal B. GND ≤ VB ≤ VDD.
Chip Select. Active Low. Logic high signal can be higher than VDD, but lower than 5.5 V.
Positive Power Supply, 2.7 V to 5.5 V.
Rev. B | Page 6 of 16
AD5227
TYPICAL PERFORMANCE CHARACTERISTICS
0.25
0.25
–40°C
+25°C
+85°C
+105°C
VDD = 5.5V
0.05
0
–0.05
–0.10
–0.15
–0.20
0
8
16
24
32
40
CODE (Decimal)
48
56
0.10
0.05
0
–0.05
–0.10
–0.15
–0.20
–0.25
64
0
Figure 6. R-INL vs. Code vs. Temperature, VDD = 5 V
48
56
64
–0.1
–0.2
0.10
–0.3
FSE (LSB)
0.05
0
–0.05
–0.4
VDD = 5.5V
–0.5
–0.6
–0.10
VDD = 2.7V
–0.15
0
8
16
24
32
40
CODE (Decimal)
48
56
04419-0-013
–0.7
04419-0-008
RHEOSTAT MODE DNL (LSB)
0.15
–0.20
–0.8
–0.9
–40
64
Figure 7. R-DNL vs. Code vs. Temperature, VDD = 5 V
–20
0
20
40
60
TEMPERATURE (°C)
80
100
Figure 10. Full-Scale Error vs. Temperature
0.25
1.0
–40°C
+25°C
+85°C
+105°C
VDD = 5.5V
0.20
0.15
0.9
0.8
VDD = 2.7V
0.7
0.05
0.6
ZSE (LSB)
0.10
0
–0.05
0.5
0.3
–0.15
0.2
–0.20
0
8
16
24
32
40
CODE (Decimal)
48
56
VDD = 5.5V
0.4
–0.10
04419-0-010
POTENTIOMETER MODE INL (LSB)
24
32
40
CODE (Decimal)
0
–40°C
+25°C
+85°C
+105°C
VDD = 5.5V
0.20
–0.25
16
Figure 9. DNL vs. Code vs. Temperature, VDD = 5 V
0.25
–0.25
8
04419-0-014
–0.25
0.15
04419-0-012
0.10
04419-0-007
RHEOSTAT MODE INL (LSB)
0.15
–40°C
+25°C
+85°C
+105°C
VDD = 5.5V
0.20
POTENTIOMETER MODE DNL (LSB)
0.20
0.1
0
–40
64
Figure 8. INL vs. Code, VDD = 5 V
–20
0
20
40
60
TEMPERATURE (°C)
80
Figure 11. Zero-Scale Error vs. Temperature
Rev. B | Page 7 of 16
100
AD5227
20
1
10kΩ
50kΩ
100kΩ
VDD = 5.5V
–20
0
20
40
60
TEMPERATURE (°C)
80
10
5
0
–5
–10
–15
–20
100
Figure 12. Supply Current vs. Temperature
0
8
16
24
32
40
CODE (Decimal)
48
20
NOMINAL RESISTANCE, RAB (kΩ)
RAB = 100kΩ
04419-0-016
RAB = 50kΩ
RAB = 10kΩ
0
20
40
60
TEMPERATURE (°C)
80
POTENTIOMETER MODE TEMPCO (ppm/°C)
VDD = 5.5V
–20
64
10
5
0
–5
–10
–15
–20
100
10kΩ
50kΩ
100kΩ
VDD = 5.5V
15
Figure 13. Nominal Resistance vs. Temperature
0
8
16
24
32
40
CODE (Decimal)
48
56
64
Figure 16. Potentiometer Mode Tempco ΔRWB/ΔT vs. Code
120
6
REF LEVEL
0dB
/DIV
6.0dB
MARKER 461 441.868Hz
MAG (A/R) –8.957dB
TA = 25°C
VDD = 5.5V
VA = 50mV rms
VDD = 2.7V
0
100
32 STEPS
–6
16 STEPS
80
–12
8 STEPS
–18
60
dB
4 STEPS
VDD = 5.5V
–24
2 STEPS
–30
40
1 STEP
–36
0
–40
–20
0
20
40
60
TEMPERATURE (°C)
80
100
–42
04419-0-042
20
04419-0-017
WIPER RESISTANCE, RW (Ω)
56
Figure 15. Rheostat Mode Tempco ΔRWB/ΔT vs. Code
1
0.1
–40
04419-0-018
RHEOSTAT MODE TEMPCO (ppm/°C)
15
04419-0-019
0.1
–40
04419-0-015
SUPPLY CURRENT (μA)
VDD = 5.5V
–48
–54
1k
START 1 000.000Hz
Figure 14. Wiper Resistance vs. Temperature
10k
1M
100k
STOP 1 000 000.000Hz
Figure 17. Gain vs. Frequency vs. Code, RAB = 10 kΩ
Rev. B | Page 8 of 16
AD5227
REF LEVEL
0dB
/DIV
6.0dB
MARKER 100 885.289Hz
MAG (A/R) –9.060dB
TA = 25°C
VDD = 5.5V
VA = 50mV rms
0
32 STEPS
–6
150
16 STEPS
–12
IDD (μA)
8 STEPS
–18
dB
200
4 STEPS
–24
100
2 STEPS
VDD = 5V
–30
1 STEP
50
–36
04419-0-024
6
04419-0-043
–42
–48
–54
1k
10k
100k
1M
FREQUENCY (Hz)
1M
100k
START 1 000.000Hz
VDD = 3V
0
10k
STOP 1 000 000.000Hz
Figure 21. IDD vs. CLK Frequency
Figure 18. Gain vs. Frequency vs. Code, RAB = 50 kΩ
REF LEVEL
0dB
/DIV
6.0dB
MARKER 52 246.435Hz
MAG (A/R) –9.139dB
1.2
TA = 25°C
VDD = 5.5V
VA = 50mV rms
1.0
0
32 STEPS
–6
16 STEPS
–12
8 STEPS
–18
4 STEPS
–24
2 STEPS
–30
1 STEP
–36
A = OPEN
TA = 25°C
RAB = 10kΩ
0.8
0.6
0.4
RAB = 50kΩ
0.2
–42
RAB = 100kΩ
04419-0-044
–48
–54
1k
10k
START 1 000.000Hz
0
0
8
16
1M
100k
04419-0-025
dB
THEORETICAL IWB_MAX (mA)
6
10M
24
32
40
CODE (Decimal)
48
56
64
STOP 1 000 000.000Hz
Figure 22. Maximum IWB vs. Code
Figure 19. Gain vs. Frequency vs. Code, RAB = 100 kΩ
0
VB = 0V
STEP = MIDSCALE, VA = VDD, VB = 0V
VA
1
PSRR (dB)
–20
STEP N+1
VDD = 3V DC ±10% p-p AC
–40
VDD = 5V
VA = 5V
VB = 0V
1k
10k
FREQUENCY (Hz)
100k
04419-0-023
VDD = 5V DC ±10% p-p AC
04419-0-022
2
–60
100
VW
STEP N
CH1 2.00V
1M
CH2 50.0mV
M 400ns
A CH2
T
0.00000s
Figure 23. Step Change Settling Time
Figure 20. PSRR
Rev. B | Page 9 of 16
60.0mV
AD5227
THEORY OF OPERATION
The AD5227 is a 64-position 3-terminal digitally controlled
potentiometer device. It presets to a midscale at system poweron. When CS is enabled, changing the resistance settings is
achieved by clocking the CLK pin. It is negative-edge triggered,
and the direction of stepping is determined by the state of the
U/D input. When the wiper reaches the maximum or the
minimum setting, additional CLK pulses do not change the
wiper setting.
The end-to-end resistance, RAB, has 64 contact points accessed
by the wiper terminal, plus the B terminal contact, assuming
that RWB is used (see Figure 25). Clocking the CLK input steps,
RWB by one step. The direction is determined by the state of
U/D pin. The change of RWB can be determined by the number
of clock pulses, provided that the AD5227 has not reached its
maximum or minimum scale. ΔRWB can, therefore, be
approximated as
VDD
R
⎞
⎛
ΔRWB = ±⎜ CP × AB + RW ⎟
64
⎠
⎝
AD5227
6-BIT UP/DOWN
CONTROL
LOGIC
CLK
A
where:
W
CP is the number of clock pulses.
RAB is the end-to-end resistance.
RW is the wiper resistance contributed by the on-resistance of
the internal switch.
B
GND
WIPER
REGISTER
04419-0-026
POR
MIDSCALE
Since in the lowest end of the resistor string a finite wiper
resistance is present, care should be taken to limit the current
flow between W and B in this state to a maximum pulse current
of no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switches can occur.
Figure 24. Functional Block Diagram
A
Similar to the mechanical potentiometer, the resistance of the
RDAC between the Wiper W and Terminal A also produces a
digitally controlled complementary resistance, RWA. When these
terminals are used, the B terminal can be opened or shorted to
W. Similarly, ΔRWA can be approximated as
RS
RS
RS
W
RW
RDAC
UP/DOWN
CTRL AND
DECODE
R
ΔRWA = ±⎛⎜ (64 − CP ) AB + RW ⎞⎟
64
⎝
⎠
RS
B
RS = RAB/64
04419-0-027
D0
D1
D2
D3
D4
D5
Equations 1 and 2 do not apply when CP = 0.
Figure 25. AD5227 Equivalent RDAC Circuit
PROGRAMMING THE DIGITAL POTENTIOMETERS
Rheostat Operation
If only the W-to-B or W-to-A terminals are used as variable
resistors, the unused terminal can be opened or shorted with W.
This operation is called rheostat mode and is shown in Figure 26.
A
W
B
Potentiometer Mode Operation
If all three terminals are used, the operation is called
potentiometer mode. The most common configuration is the
voltage divider operation as shown in Figure 27.
A
W
B
The typical distribution of the resistance tolerance from device
to device is process lot dependent. It is possible to have ±20%
tolerance.
W
B
VI
A
04419-0-028
A
(2)
VC
W
Figure 26. Rheostat Mode Configuration
B
04419-0-029
CS
U/D
(1)
Figure 27. Potentiometer Mode Configuration
Rev. B | Page 10 of 16
AD5227
ΔVWB = +
ΔVWB
CP
V A U/D = 1
64
(3)
CP
=−
V A U/D = 0
64
(4)
Unlike rheostat mode operation where the absolute tolerance is
high, potentiometer mode operation yields an almost ratiometric
function of CP/64 with a relatively small error contributed by
the RW term. The tolerance effect is, therefore, almost canceled.
Although the thin film step resistor, RS, and CMOS switches
resistance, RW, have very different temperature coefficients, the
ratiometric adjustment also reduces the overall temperature
coefficient to 5 ppm/°C except at low value codes where RW
dominates.
Potentiometer mode operation includes an op amp gain
configuration among others. The A, W, and B terminals can be
input or output terminals and have no polarity constraint
provided that |VAB|, |VWA|, and |VWB| do not exceed VDD-to-GND.
DIGITAL INTERFACE
The AD5227 contains a 3-wire serial input interface. The three
inputs are clock (CLK), chip select (CS), and up/down control
(U/D). These inputs can be controlled digitally for optimum
speed and flexibility
When CS is pulled low, a clock pulse increments or decrements
the up/down counter. The direction is determined by the state
of the U/D pin. When a specific state of the U/D remains, the
device continues to change in the same direction under consecutive clocks until it comes to the end of the resistance
setting. All digital inputs, CS, CLK, and U/D pins, are protected
with a series input resistor and a parallel Zener ESD structure as
shown in Figure 28.
POWER-UP AND POWER-DOWN SEQUENCES
Because of the ESD protection diodes, it is important to power
on VDD before applying any voltage to Terminals A, B, and W.
Otherwise, the diodes are forward-biased such that VDD can be
powered unintentionally and can affect the rest of the system
circuit. Similarly, VDD should be powered down last. The ideal
power-on sequence is in the following order: GND, VDD, VA/B/W,
and digital inputs.
VDD
A
W
B
GND
Figure 29. Maximum Terminal Voltages Set by VDD and GND
LAYOUT AND POWER SUPPLY BIASING
It is a good practice to use compact, minimum lead length
layout design. The leads to the input should be as direct as
possible with a minimum conductor length. Ground paths
should have low resistance and low inductance. It is also good
practice to bypass the power supplies with quality capacitors.
Low ESR (equivalent series resistance) 1 μF to 10 μF tantalum
or electrolytic capacitors should be applied at the supplies to
minimize any transient disturbance and filter low frequency
ripple.
Figure 30 illustrates the basic supply bypassing configuration
for the AD5227. The ground pin of the AD5227 is a digital
ground reference that should be joined to the common ground
at a single point to minimize the digital ground bounce.
AD5227
VDD
LOGIC
04419-0-030
1kΩ
operating voltages. Voltage present on Terminal A, B, or W that
exceeds VDD by more than 0.5 V is clamped by the diode and,
therefore, elevates VDD. There is no polarity constraint between
VAB, VWA, and VWB, but they cannot be higher than VDD-toGND.
04419-0-031
The change of VWB is known provided that the AD5227 has not
reached the maximum or minimum scale. If one ignores the
effect of the wiper resistance, the transfer functions can be
simplified as
+
C2
10μF
C1
0.1μF
VDD
04419-0-032
GND
Figure 28. Equivalent ESD Protection Digital Pins
Figure 30. Power Supply Bypassing
TERMINAL VOLTAGE OPERATION RANGE
The AD5227 is designed with internal ESD protection diodes
(Figure 29), but the diodes also set the boundary of the terminal
Rev. B | Page 11 of 16
AD5227
APPLICATIONS
ADJUSTABLE LED DRIVER
MANUAL CONTROL WITH TOGGLE AND
PUSHBUTTON SWITCHES
The AD5227’s simple interface allows it to be used with
mechanical switches for simple manual operation. The states of
the CS and U/D can be selected by toggle switches and the CLK
input can be controlled by a pushbutton switch. Because of the
numerous bounces due to contact closure, the pushbutton
switch should be debounced by flip-flops or by the ADM812 as
shown in Figure 31.
The AD5227 can be used in many electronics-level adjustments
such as LED drivers for LCD panel backlight control. Figure 33
shows an adjustable LED driver. The AD5227 sets the voltage
across the white LED D1 for the brightness control. Since U2
handles up to 250 mA, a typical white LED with VF of 3.5 V
requires a resistor, R1, to limit the U2 current. This circuit is
simple but not power-efficient, therefore the U2 shutdown pin
can be toggled with a PWM signal to conserve power.
5V
CS
UP/DOWN
C1
1μF
C2
0.1μF
VDD
CLK
RESET
ADM812
GND
A
CS
CLK
U/D
04419-0-033
MR
V+
U1
AD5227
U/D
VCC
C3
0.1μF
–
U2
AD8591
R1
SD 6Ω
W
+
10kΩ
WHITE
LED
D1
V–
B
PWM
MANUAL CONTROL WITH ROTARY ENCODER
Figure 33. Low Cost Adjustable LED Driver
Figure 32 shows another way of using AD5227 to emulate
mechanical potentiometer in a rotary knob operation. The
rotary encoder U1 has a C ground terminal and two out-ofphase signals, A and B. When U1 is turned clockwise, a pulse
generated from the B terminal leads a pulse generated from the
A terminal and vice versa. Signals A and B of U1 pass through a
quadrature decoder U2 that translates the phase difference
between A and B of U1 into compatible inputs for U3 AD5227.
Therefore, when B leads A (clockwise), U2 provides the AD5227
with a logic high U/D signal, and vice versa. U2 also filters
noise, jitter, and other transients as well as debouncing the
contact bounces generated by U1.
ADJUSTABLE CURRENT SOURCE FOR LED DRIVER
Since LED brightness is a function of current rather than
forward voltage, an adjustable current source is preferred over a
voltage source as shown in Figure 34.
VIN
5V
VOUT
U2
U1
AD5227
ADP3333
ARM-1.5
5V
SD
GND
VDD
B
W
CS
CLK
PWM
U/D
10kΩ
A
GND
5V
R1
10kΩ
QUADRATURE
DECODER
R3
10kΩ 1
U1
ROTARY
ENCODER
B
C
A
RSET
0.1Ω
R1
418kΩ
R2
10kΩ
2
3
4
U3
AD5227
CLK
VDD
U/D
VSS
X4/X1
A
V+
U2
LS7084
RBIAS
B
5V
DIGITAL
POTENTIOMETER
A1
8
1
7
2
6
3 A1
B1 6
5
4
W1 5
CLK
VDD
U/D
CS
GND
–
U3
8
AD8591
7
V–
+
VL
D1
B1
ID
W1
Figure 34. Adjustable Current Source for LED Driver
04419-0-034
RE11CT-V1Y12-EF2CS
Figure 32. Manual Rotary Control
04419-0-035
GND
Figure 31. Manual Push Button Up/Down Control
04419-0-036
5V
INCREMENT
5V
AD5227
The load current can be found as the VWB of the AD5227
divided by RSET.
ID =
Rev. B | Page 12 of 16
VWB
RSET
(5)
AD5227
ADJUSTABLE HIGH POWER LED DRIVER
Figure 35 shows a circuit that can drive three to four high power
LEDs. ADP1610 is an adjustable boost regulator that provides
the voltage headroom and current for the LEDs. The AD5227
and the op amp form an average gain of 12 feedback network
that servos the RSET voltage and ADP1610’s FB pin 1.2 V band
gap reference voltage. As the loop is set, the voltage across RSET
is regulated around 0.1 V and adjusted by the digital
potentiometer.
I LED =
VRSET
AUTOMATIC LCD PANEL BACKLIGHT CONTROL
With the addition of a photocell sensor, an automatic brightness
control can be achieved. As shown in Figure 36, the resistance
of the photocell changes linearly but inversely with the light
output. The brighter the light output, the lower the photocell
resistance and vice versa. The AD5227 sets the voltage level that
is gained up by U2 to drive N1 to a desirable brightness. With the
photocell acting as the variable feedback resistor, the change in
the light output changes the R2 resistance, therefore causing U2
to drive N1 accordingly to regulate the output. This simple low
cost implementation of the LED controller can compensate for
the temperature and aging effects typically found in high power
LEDs. Similarly, for power efficiency, a PWM signal can be
applied at the gate of N2 to switch the LED on and off without
any noticeable effect.
5V
5V
R2
R1
1kΩ
D1
PHOTOCELL
5V
C1
1μF
(6)
C2
0.1μF
RSET
RSET should be small enough to conserve power but large
enough to limit maximum LED current. R3 should also be used
in parallel with AD5227 to limit the LED current within an
achievable range. A wider current adjustment range is possible
by lowering the R2 to R1 ratio, as well as changing R3
accordingly.
V+
U1
AD5227
VDD
A
N1
–
U2
AD8591
2N7002
W
+
10kΩ
CLK
C3
0.1μF
5V
CS
WHITE
LED
V–
SD
B
U/D
GND
04419-0-038
The U1 ADP3333ARM-1.5 is a 1.5 V LDO that is lifted above
or lowered below 0 V. When VWB of the AD5227 is at minimum,
there is no current through D1, so the GND pin of U1 would be
at −1.5 V if U3 were biased with the dual supplies. As a result,
some of the U2 low resistance steps have no effect on the output
until the U1 GND pin is lifted above 0 V. When VWB of the
AD5227 is at its maximum, VOUT becomes VL + VAB, so the U1
supply voltage must be biased with adequate headroom.
Similarly, a PWM signal can be applied at the U1 shutdown pin
for power efficiency. This circuit works well for a single LED.
PWM
Figure 36. Automatic LCD Panel Backlight Control
6-BIT CONTROLLER
5V
R4
13.5kΩ
U2
IN
L1
10μF
ADP1610
PWM
SD
1.2V
FB
COMP
RC
100kΩ
CC
390pF
SS
VOUT
SW
D1
C3
10μF
RT GND
D2
CSS
10nF
D3
C8
5V
0.1μF
D4
The AD5227 can form a simple 6-bit controller with a clock
generator, a comparator, and some output components. Figure 37
shows a generic 6-bit controller with a comparator that first
compares the sampling output with the reference level and
outputs either a high or low level to the AD5227 U/D pin. The
AD5227 then changes step at every clock cycle in the direction
indicated by the U/D state. Although this circuit is not as elegant
as the one shown in Figure 36, it is self-contained, very easy to
design, and can adapt to various applications.
U3
V+
AD5227
VDD
AD8541
U1
CLK
RSET
0.25Ω
–
V–
W
B
A
–
U3
U/D
U1
AD5227
L1–SLF6025-100M1R0
D1–MBR0520LT1
R2
1.1kΩ
U1
5V
+
B
CS
GND
R1
100Ω
OUTPUT
+
OP AMP
10kΩ
–
04419-0-037
R3
200Ω
AD8531
SAMPLING_OUTPUT
U2
COMPARATOR
+
REF
Figure 35. Adjustable Current Source for LEDs in Series
Figure 37. 6-Bit Controller
Rev. B | Page 13 of 16
04419-0-039
C2
10μF
AD5227
CONSTANT BIAS WITH SUPPLY TO
RETAIN RESISTANCE SETTING
3.50
Users who consider EEMEM potentiometers but cannot justify
the additional cost and programming for their designs can consider constantly biasing the AD5227 with the supply to retain
the resistance setting as shown in Figure 38. The AD5227 is
designed specifically with low power to allow power conservation
even in battery-operated systems. As shown in Figure 39, a
similar low power digital potentiometer is biased with a 3.4 V
450 mA/hour Li-Ion cell phone battery. The measurement shows
that the device drains negligible power. Constantly biasing the
potentiometer is a practical approach because most portable
devices do not require detachable batteries for charging.
Although the resistance setting of the AD5227 is lost when the
battery needs to be replaced, this event occurs so infrequently
that the inconvenience is minimal for most applications.
3.48
TA = 25°C
VDD
SW1
U1
U2
AD5227
VDD
COMPONENT X
COMPONENT Y
GND
GND
+
GND
–
GND
04419-0-040
BATTERY OR
SYSTEM POWER
VDD
U3
VDD
Figure 38. Constant Bias AD5227 for Resistance Retention
Rev. B | Page 14 of 16
3.47
3.46
3.45
3.44
3.43
3.42
04419-0-041
BATTERY VOLTAGE (V)
3.49
3.41
3.40
0
2
4
6
DAYS
8
10
Figure 39. Battery Consumption Measurement
12
AD5227
OUTLINE DIMENSIONS
2.90 BSC
8
7
6
5
1
2
3
4
1.60 BSC
2.80 BSC
PIN 1
INDICATOR
0.65 BSC
*0.90
0.87
0.84
1.95
BSC
*1.00 MAX
0.10 MAX
0.38
0.22
0.20
0.08
SEATING
PLANE
8°
4°
0°
0.60
0.45
0.30
*COMPLIANT TO JEDEC STANDARDS MO-193-BA WITH
THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
Figure 40. 8-Lead Thin Small Outline Transistor Package [TSOT]
(UJ-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD5227BUJZ10-RL7 2
AD5227BUJZ10-R22
AD5227BUJZ50-RL72
AD5227BUJZ50-R22
AD5227BUJZ100-RL72
AD5227BUJZ100-R22
AD5227EVAL
RAB 1 (kΩ)
10
10
50
50
100
100
10
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
8-Lead TSOT
8-Lead TSOT
8-Lead TSOT
8-Lead TSOT
8-Lead TSOT
8-Lead TSOT
Evaluation Board
1
Package Option
UJ-8
UJ-8
UJ-8
UJ-8
UJ-8
UJ-8
Ordering Quantity
3000
250
3000
250
3000
250
1
Branding
D3G
D3G
D3H
D3H
D3J
D3J
The end-to-end resistance RAB is available in 10 kΩ, 50 kΩ, and 100 kΩ versions. The final three characters of the part number determine the nominal resistance value,
for example, 10 kΩ = 10.
2
Z = RoHS Compliant Part.
Rev. B | Page 15 of 16
AD5227
NOTES
© 2004–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04419–0–5/09(B)
Rev. B | Page 16 of 16