FAIRCHILD FDP8030L

FDP8030L/FDB8030L
N-Channel Logic Level PowerTrench MOSFET
General Description
Features
This N-Channel Logic level MOSFET has been
designed specifically to improve the overall efficiency of
DC/DC converters using either synchronous or
conventional switching PWM controllers.
• 80 A, 30 V.
These MOSFETS feature faster switching and lower
gate charge than other MOSFETS with comparable
RDS(on) specifications.
The result is a MOSFET that is easy and safer to drive
(even at very high frequencies), and DC/DC power
supply designs with higher overall efficiency.
RDS(ON) = 0.0035 Ω @ VGS = 10 V
RDS(ON) = 0.0045 Ω @ VGS = 4.5 V
• Critical DC electrical parameters specified at
elevated temperature
• Rugged internal source-drain diode can eliminate the
need for an external Zener diode transient
suppressor
• High performance trench technology for extremely
low RDS(ON)
• 175°C maximum junction temperature rating
D
D
G
G
D
G
S
TO-220
FDP Series
S
Absolute Maximum Ratings
Symbol
TO-263AB
FDB Series
S
o
TA=25 C unless otherwise noted
Parameter
VDSS
Drain-Source Voltage
VGSS
Gate-Source Voltage
ID
Drain Current
PD
Total Power Dissipation @# TC = 25°C
– Continuous
(Note 1)
– Pulsed
(Note 1)
Derate above 25°C
TJ, TSTG
Operating and Storage Junction Temperature Range
TL
Maximum lead temperature for soldering purposes,
1/8” from case for 5 seconds
Ratings
Units
30
V
±20
V
80
A
300
187
W
1.25
W°C
-65 to +175
°C
275
°C
Thermal Characteristics
RθJC
Thermal Resistance, Junction-to-Case
0.8
°C/W
RθJA
Thermal Resistance, Junction-to-Ambient
62.5
°C/W
1999 Fairchild Semiconductor Corporation
FDP8030L Rev C(W)
FDP8030L/FDB8030L
November 1999
Electrical Characteristics
Symbol
TA = 25°C unless otherwise noted
Parameter
Test Conditions
Min
Typ
Max Units
Drain-Source Avalanche Ratings (Note 1)
WDSS
IAR
Single Pulse Drain-Source
Avalanche Energy
Maximum Drain-Source Avalanche
Current
VDD = 20 V,
ID = 80 A
1500
mJ
80
A
Off Characteristics
BVDSS
Drain–Source Breakdown Voltage
VGS = 0 V, ID = 250 µA
∆BVDSS
∆TJ
IDSS
Breakdown Voltage Temperature
Coefficient
Zero Gate Voltage Drain Current
ID = 250 µA, Referenced to 25°C
VDS = 24 V,
VGS = 0 V
10
µA
IGSSF
Gate–Body Leakage, Forward
VGS = 20 V,
VDS = 0 V
100
nA
IGSSR
Gate–Body Leakage, Reverse
VGS = –20 V
VDS = 0 V
–100
nA
2
V
On Characteristics
30
V
23
mV/°C
(Note 2)
VDS = VGS, ID = 250 µA
ID = 250 µA, Referenced to 25°C
VGS(th)
Gate Threshold Voltage
∆VGS(th)
∆TJ
RDS(on)
Gate Threshold Voltage
Temperature Coefficient
Static Drain–Source
On–Resistance
VGS = 4.5 V,
ID = 80 A
TJ=125°C
ID = 70 A
ID(on)
On–State Drain Current
VGS = 10 V,
VDS = 10 V
gFS
Forward Transconductance
VDS = 10 V,
ID = 80 A
170
VDS = 15 V,
f = 1.0 MHz
V GS = 0 V,
10500
pF
2700
pF
1650
pF
VGS = 10 V,
1
1.5
–5
3.1
4.0
3.6
mV/°C
3.5
5.6
4.5
60
mΩ
A
S
Dynamic Characteristics
Ciss
Input Capacitance
Coss
Output Capacitance
Crss
Reverse Transfer Capacitance
Switching Characteristics
tD(on)
Turn–On Delay Time
tr
Turn–On Rise Time
tD (off)
Turn–Off Delay Time
tf
Turn–Off Fall Time
Qg
Total Gate Charge
Qgs
Gate–Source Charge
Qgd
Gate–Drain Charge
(Note 2)
VDD = 15 V,
VGS = 4.5 V,
RGS = 10 Ω
ID = 50 A,
RGEN = 10 Ω
VDS = 15 V,
ID = 80 A, VGS = 5 V
20
35
ns
185
225
ns
160
200
ns
200
240
ns
120
170
nC
27
nC
48
nC
Drain–Source Diode Characteristics and Maximum Ratings
IS
Maximum Continuous Drain–Source Diode Forward Current
(Note 1)
80
ISM
Maximum Pulsed Drain-Source Diode Forward Current
(Note 1)
300
A
VSD
Drain–Source Diode Forward Voltage
1.3
V
VGS = 0 V,
IS = 80 A
(Note 1)
1
A
Notes:
1. Pulse Test: Pulse Width < 300µs, Duty Cycle < 2.0%
FDP8030L Rev C(W)
FDP8030L/FDB8030L
Typical Characteristics
3
3.0V
R DS(ON) , NORMALIZED
4.5V
3.5V
80
60
40
2.5V
20
DRAIN-SOURCE ON-RESISTANCE
I D , DRAIN-SOURCE CURRENT (A)
100
2
0
0.5
1
1.5
V DS , DRAIN-SOURCE VOLTAGE (V)
3.0V
1.5
3.5V
4.5V
10V
0
20
2
Figure 1. On-Region Characteristics.
6.0V
1
0.5
0
VGS = 2.5V
2.5
40
60
80
I D, DRAIN CURRENT (A)
100
120
Figure 2. On-Resistance Variation with
Drain Current and Gate Voltage.
0.01
ID = 40A
0.009
RDS(ON), ON-RESISTANCE (OHM)
ID = 80A
VGS = 10V
1.4
1.2
1
0.8
0.008
0.007
0.006
TA = 125oC
0.005
0.004
0.003
TA = 25oC
0.002
0.001
0.6
-50
-25
0
25
50
75
100
T J, JUNCTION TEMPERATURE (°C)
125
0
150
2
4
5
6
7
8
Figure 4. On-Resistance Variation with
Gate-to-Source Voltage.
60
60
I S, REVERSE DRAIN CURRENT (A)
V DS = 10V
50
40
TA = -55°C
25°C
125°C
30
20
10
0
3
VGS, GATE TO SOURCE VOLTAGE (V)
Figure 3. On-Resistance Variation with
Temperature.
I D, DRAIN CURRENT (A)
R DS(ON), NORMALIZED
DRAIN-SOURCE ON-RESISTANCE
1.6
1
2
3
V GS, GATE TO SOURCE VOLTAGE (V)
Figure 5. Transfer Characteristics.
4
10
TA = 125°C
1
25°C
0.1
-55°C
0.01
0.001
0.0001
V GS = 0V
0
0.2
0.4
0.6
0.8
1
1.2
V SD , BODY DIODE FORWARD VOLTAGE (V)
1.4
Figure 6. Body Diode Forward Voltage Variation
with Source Current and Temperature.
FDP8030L Rev C(W)
FDP8030L/FDB8030L
Typical Characteristics
18000
10
V DS = 5V
10V
15V
8
6
4
2
0
40
80
120
160
Q g, GATE CHARGE (nC)
200
C oss
2000
C rss
VGS = 0V
500
0.1
240
Figure 7. Gate Charge Characteristics.
0.5
1
2
5
10
V DS, DRAIN TO SOURCE VOLTAGE (V)
30
Figure 8. Capacitance Characteristics.
600
5000
100
µs
it
Lim
)
R
(ON
DS
1ms
10
ms
100
ms
DC
100
50
20
10
VGS = 10V
SINGLE PULSE
RθJC = 0.8 °C/W
TC = 25 °C
5
2
1
0.5
0.3
SINGLE PULSE
R θJC = 0.8°C/W
TC = 25°C
4000
POWER (W)
300
I D, DRAIN CURRENT (A)
5000
1000
0
C iss
10000
CAPACITANCE (pF)
V GS , GATE-SOURCE VOLTAGE (V)
ID = 80A
3000
2000
1000
1
3
5
10
20
V DS , DRAIN-SOURCE VOLTAGE (V)
30
50
0
0.1
Figure 9. Maximum Safe Operating Area.
0.3
1
3
10
30
100
SINGLE PULSE TIME (mSEC)
300
1,000
Figure 10. Single Pulse Maximum
Power Dissipation.
TRANSIENT THERMAL RESISTANCE
r(t), NORMALIZED EFFECTIVE
1
0.5
D = 0.5
0.3
0.2
0.2
0.1
0.05
0.03
0.02
RθJC (t) = r(t) * RθJC
RθJC = 0.8 °C/W
0.1
P(pk)
0.05
t1
0.02
0.01
Single Pulse
0.005
0.01
0.05
t2
TJ - TC = P * R θJC (t)
Duty Cycle, D = t 1 /t 2
0.1
0.5
1
5
t1 ,TIME (ms)
10
50
100
500
1000
Figure 11. Transient Thermal Response Curve.
Thermal characterization performed using the conditions described in Note 1c.
Transient thermal response will change depending on the circuit board design.
FDP8030L Rev C(W)
TO-220 Tape and Reel Data and Package Dimensions
TO-220 Tube Packing
Configuration: Figur e 1.0
Packaging Description:
TO-220 parts are ship ped normally in tube. The tube is
made of PVC plastic treated with anti -stati c agent.These
tubes in standard option are placed inside a dissipative
plastic bag, barcode labeled, and placed inside a box
made of recyclable corrugated pa per. One box contains
two ba gs maximum (see fig. 1.0). And one or several o f
these boxes are placed inside a labeled shipp ing bo x
whic h c omes in different sizes dependi ng on the nu mber
of parts ship ped. The other option comes in bulk as
described in the Packagin g Information table. The unit s in
this option are placed inside a small box laid w ith antistatic bubble sheet. These smaller boxes are individually
labeled and placed ins ide a larger box (see fig. 3.0).
These larger or intermediate boxes then will b e placed
finally inside a labeled shipping box whic h still comes in
different sizes depending on the number of units shipped.
45 unit s per Tube
12 Tubes per Bag
530mm x 130mm x 83mm
Intermediate box
2 bag s per Box
Conduct ive Plasti c B ag
TO-220 Packaging
Information: Figure 2.0
FSCINT Labe l samp le
FAIRCHILD SEMICONDUCTOR CORPORATION
TO-220 Packaging Information
Packaging Option
Packaging type
Qty per Tube/Box
NSID:
Standard
CBVK741B019
QTY:
FDP7060
HTB:B
1080
SPEC:
S62Z
(no f l ow code )
Rail/Tube
BULK
45
300
D/C1:
D9842
SPEC REV:
B2
QA REV:
530x130x83
114x102x51
Max qty per Box
1,080
1,500
Weight per unit (gm)
1.4378
1.4378
Box Dimension (mm)
LOT:
1080 uni ts maxi mum
quant it y per bo x
FSCINT Label
(FSCINT)
Note/Comments
TO-220 bulk Packing
Configuration: Figure 3.0
An ti-stati c
Bubbl e Sheet s
FSCINT Label
530mm x 130mm x 83mm
Intermediate box
1500 uni ts maxi mum
quant it y per intermediate box
300 units per
EO70 box
5 EO70 boxe s per per
Interm ediate Bo x
114mm x 102mm x 51mm
EO70 Immed iate Box
FSCINT Label
TO-220 Tube
Configuration: Figure 4.0
0.123
+0.001
-0.003
0.165
0.080
Note: All dim ensions are in inches
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
F 9852
NDP4060L
0.275
0.450
±.030
F 9852
NDP4060L
1.300
±.015
0.032
±.003
20.000
+0.031
-0.065
0.160
0.800
0.275
August 1999, Rev. B
TO-220 Tape and Reel Data and Package Dimensions, continued
TO-220 (FS PKG Code 37)
1:1
Scale 1:1 on letter size paper
Dimensions shown below are in:
inches [millimeters]
Part Weight per unit (gram): 1.4378
September 1998, Rev. A
TO-263AB/D2PAK Tape and Reel Data and Package
Dimensions
TO-263AB/D2PAK Packaging
Configuration: Figure 1.0
Packaging Description:
TO-263/D2PAK parts are shipped in tape. The carrier tape
is made from a dissipative (carbon filled) polycarbonate
resin. The cover tape is a multilayer film (Heat Activated
Adhesive in nature) primarily composed of polyester film,
adhesive layer, sealant, and anti-static sprayed agent.
These reeled parts in standard option are shipped with
800 units per 13" or 330cm diameter reel. The reels are
dark blue in color and is made of polystyrene plastic (antistatic coated). This and some other options are further
described in the Packaging Information table.
EL ECT ROST AT IC
SEN SIT IVE DEVICES
DO NO T SHI P OR STO RE N EAR ST RO NG EL ECT ROST AT IC
EL ECT RO M AGN ETI C, M AG NET IC O R R ADIO ACT IVE FI ELD S
TNR D ATE
PT NUMB ER
PEEL STREN GTH MIN ___ __ ____ __ ___gms
MAX ___ ___ ___ ___ _ gms
Antistatic Cover Tape
ESD Label
These full reels are individually barcode labeled, dry
packed, and placed inside a standard intermediate box
(illustrated in figure 1.0) made of recyclable corrugated
brown paper. One box contains one reel maximum. And
these boxes are placed inside a barcode labeled shipping
box which comes in different sizes depending on the
number of parts shipped.
CAUTION
Static Dissipative
Embossed Carrier Tape
Moisture Sensitive
Label
F63TNR
Label
F9835
FDB603AL
F9835
FDB603AL
F9835
FDB603AL
Customized
Label
F9835
FDB603AL
TO-263AB/D2PAK Packaging Information
Packaging Option
Packaging type
Qty per Reel/Tube/Bag
Reel Size
Box Dimension (mm)
Standard
(no flow code)
TNR
Rail/Tube
800
45
L86Z
13" Dia
-
359x359x57
530x130x83
800
1,080
Weight per unit (gm)
1.4378
1.4378
Weight per Reel
1.6050
-
Max qty per Box
TO-263AB/D2PAK Unit Orientation
359mm x 359mm x 57mm
Standard Intermediate box
ESD Label
Note/Comments
Moisture Sensitive
Label
F63TNR Label sample
F63TNR Label
LOT: CBVK741B019
QTY: 800
FSID: FDB6320L
SPEC:
D/C1: D9842
D/C2:
QTY1:
QTY2:
SPEC REV:
CPN:
N/F: F
DRYPACK Bag
(F63TNR)3
TO-263AB/D2PAK Tape Leader and Trailer
Configuration: Figure 2.0
Carrier Tape
Cover Tape
Components
Trailer Tape
400mm minimum or
25 empty pockets
Leader Tape
1520mm minimum or
95 empty pockets
September 1999, Rev. B
TO-263AB/D2PAK Tape and Reel Data and Package Dimensions, continued
TO-263AB/D2PAK Embossed Carrier Tape
Configuration: Figure 3.0
P0
D0
T
E1
F
K0
Wc
W
E2
B0
Tc
A0
D1
P1
User Direction of Feed
Dimensions are in millimeter
Pkg type
A0
B0
TO263AB/
D2PAK
(24mm)
10.60
+/-0.10
15.80
+/-0.10
W
24.0
+/-0.3
D0
D1
E1
E2
1.55
+/-0.05
1.60
+/-0.10
1.75
+/-0.10
F
22.25
min
11.50
+/-0.10
P1
P0
16.0
+/-0.1
4.0
+/-0.1
K0
T
4.90
+/-0.10
0.450
+/-0.150
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481
rotational and lateral movement requirements (see sketches A, B, and C).
Wc
0.06
+/-0.02
0.9mm
maximum
10 deg maximum
Typical
component
cavity
center line
B0
21.0
+/-0.3
Tc
0.9mm
maximum
10 deg maximum component rotation
Typical
component
center line
Sketch A (Side or Front Sectional View)
A0
Component Rotation
2PAK
TO-263AB/D
Figure 4.0
Sketch C (Top View)
Component lateral movement
Sketch B (Top View)
Reel Configuration:
Component Rotation
W1 Measured at Hub
Dim A
Max
B Min
Dim C
Dim A
max
Dim D
min
Dim N
DETAIL AA
See detail AA
W3
13" Diameter Option
W2 max Measured at Hub
Dimensions are in inches and millimeters
Tape Size
24mm
Reel
Option
13" Dia
Dim A
Dim B
13.00
330
0.059
1.5
Dim C
512 +0.020/-0.008
13 +0.5/-0.2
Dim D
0.795
20.2
Dim N
4.00
100
Dim W1
0.961 +0.078/-0.000
24.4 +2/0
Dim W2
1.197
30.4
Dim W3 (LSL-USL)
0.941 – 0.1.079
23.9 – 27.4
August 1999, Rev. B
TO-263AB/D2PAK Tape and Reel Data and Package Dimensions, continued
TO-263AB/D2PAK (FS PKG Code 45)
1:1
Scale 1:1 on letter size paper
Dimensions shown below are in:
inches [millimeters]
Part Weight per unit (gram): 1.4378
August 1998, Rev. A
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is
not intended to be an exhaustive list of all such trademarks.
ISOPLANAR™
MICROWIRE™
POP™
PowerTrench 
QFET™
QS™
Quiet Series™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
ACEx™
CoolFET™
CROSSVOLT™
E2CMOSTM
FACT™
FACT Quiet Series™
FAST®
FASTr™
GTO™
HiSeC™
SyncFET™
TinyLogic™
UHC™
VCX™
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or
2. A critical component is any component of a life
support device or system whose failure to perform can
systems which, (a) are intended for surgical implant into
be reasonably expected to cause the failure of the life
the body, or (b) support or sustain life, or (c) whose
support device or system, or to affect its safety or
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
effectiveness.
reasonably expected to result in significant injury to the
user.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or
In Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Obsolete
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. D