MAXIM DG506ACK

19-0482; Rev 3; 2/10
Monolithic CMOS Analog Multiplexers
Features
Maxim’s DG506A/DG507A are monolithic CMOS analog
multiplexers. The DG506A is a single 16-channel (1 of
16) multiplexer and the DG507A is a differential 8-channel (2 of 16) multiplexer.
S Improved 2nd Source
Both devices feature break-before-make switching.
Maxim guarantees that these multiplexers will not latchup if the power supplies are turned off with the input
signals still present as long as absolute maximum ratings
are not violated. The multiplexers operate over a wide
range of power supplies from Q4.5V to Q18V.
S Logic and Enable Inputs, TTL and CMOS Compatible
Compared to the original manufacturer’s devices,
Maxim’s DG506A/DG507A consume significantly less
power, making them ideal for portable equipment.
S Pin Compatible with Harris, Siliconix, Intersil
S Operable with ±4.5V to ±18V Supplies
S Symmetrical, Bidirectional Operation
S Latch-Up Proof Construction
S Monolithic, Low-Power CMOS Design
Ordering Information
PART†
TEMP RANGE
PIN-PACKAGE
DG506AAK
-55°C to +125°C
28 CERDIP
DG506ABK
-25°C to +85°C
28 CERDIP
DG506AC/D
0°C to +70°C
Dice
DG506ACJ
0°C to +70°C
28 Plastic Dip
DG506ACK
0°C to +70°C
28 CERDIP
DG506ACWI
0°C to +70°C
28 Wide SO
DG506AMWI/PR
-55°C to +125°C
28 Wide SO
DG507AAK
-55°C to +125°C
28 CERDIP
DG507ABK
-25°C to +85°C
28 CERDIP
Data Logging Systems
DG507AC/D
0°C to +70°C
Dice
Aircraft Heads Up Displays
DG507ACJ
0°C to +70°C
28 Plastic DIP
Data Acquisition Systems
DG507ACK
0°C to +70°C
28 CERDIP
DG507ACWI
0°C to +70°C
28 Wide SO
Maxim’s DG506A/DG507A meet or exceed the specifications of, and are drop-in replacements for Intersil’s
IH6116 and IH6216, Siliconix’s DG506A and DG507A,
and Harris’ HI506 and HI507.
Applications
Control Systems
Signal Routing
Typical Operating Circuit
-15V
ANALOG
INPUT
(OUTPUTS)
+15V
V+
CLOCK IN
BH1
NC
Pin Configurations
-15V
V+
S1a
S8a
GND
S1b
S8b
A0
DG507A
A1
A2
QB
VDa
Db
EN
ANALOG
OUTPUT
(INPUTS)
V+ 1
28 D
V+ 1
28 Da
NC 2
27 V-
Db 2
27 V-
NC 3
26 S8
NC 3
26 S8a
S16 4
25 S7
S8b 4
25 S7a
S15 5
24 S6
S7b 5
24 S6a
DG506A
DG507A
QC
S14 6
23 S5
S6b 6
QD
S13 7
22 S4
S5b 7
22 S4a
S12 8
21 S3
S4b 8
21 S3a
S11 9
20 S2
S3b 9
20 S2a
S10 10
19 S1
S2b 10
19 S1a
QA
AH1
†Devices are available in a lead(Pb)-free/RoHS-compliant
package, specify lead-free by adding “+” to the part number
when ordering.
NC
r01 r02 GND
+15V
ENABLE IN
(MUX ON-OFF
CONTROL)
8-CHANNEL SEQUENTIAL DIFFERENTIAL MUX/DEMUX
23 S5a
S9 11
18 EN
S1b 11
18 EN
GND 12
17 A0
GND 12
17 A0
NC 13
16 A1
NC 13
16 A1
A3 14
15 A2
NC 14
15 A2
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
DG506A/DG507A
General Description
DG506A/DG507A
Monolithic CMOS Analog Multiplexers
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to V-.)
V+...........................................................................................44V
GND........................................................................................25V
Digital Inputs VS, VD (Note 1)........................-2V to (V+ + 2V) or
20mA, whichever occurs first
Current, Any Terminal Except S or D..................................30mA
Continuous Current, S or D.................................................20mA
Peak Current, S or D (pulsed at 1ms, 10% duty cycle max).... 40mA
Continuous Power Dissipation (TA = +70°C)*
28-Pin Ceramic DIP (derate 16.7mW/NC above +70NC)...1333mW
28-Pin Plastic DIP (derate 14.3mW/NC above +70NC)....1143mW
28-Pin Wide SO (derate 12.5mW/°C above +70°C)...1000mW
Operating Temperature Range (A Suffix)......... -55NC to +125NC
(B Suffix)........... -25NC to +85NC
(C Suffix)................. 0NC to +70N
Storage Temperature (A and B Suffix).............. -65NC to +150NC
(C Suffix)........................ -65NC to +125NC
Lead Temperature (soldering, 10s).................................+300NC
*All leads soldered or welded to PCB.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = 15V, V- = -15V, VGND = 0V, TA = +25NC, unless otherwise indicated.)
PARAMETER
SYMBOL
CONDITIONS
DG506AA
DG507AA
MIN
TYP
(Note 2) (Note 3)
DG506AB/C
DG507AB/C
MAX
MIN
TYP
(Note 2) (Note 3)
UNITS
MAX
SWITCH
Analog Signal
Range
Drain-toSource
On-Resistance
Greatest
Change in
Drain-Source
On-Resistance
Between
Channels
Source OffLeakage
Current
Drain OffLeakage
Current
2
VANALOG
RDS(ON)
RDS(ON)
IS(OFF)
-15
Sequence each
switch on,
VAL = 0.8V,
VAH = 2.4V,
VEN = 2.4V
VD = 10V,
IS = -200FA
270
230
ID(OFF)
DG507A,
VEN = 0.8V,
VAL = 0.8V
400
+15
270
400
230
6
-10V P VS P +10V
DG506A,
VEN = 0.8V,
VAL = 0.8V
-15
V
450
I
VD = -10V,
IS = -200FA
 R DS(ON)MAX − R DS(ON)MIN 
∆R DS(ON) = 



R DS(ON)AVE


VEN = 0.8V,
VAL = 0.8V
+15
450
6
%
VS = 10V,
VD = -10V
-1
0.002
+1
-5
0.002
+5
VS = -10V,
VD = 10V
-1
-0.005
+1
-5
-0.005
+5
VD = 10V,
VS = -10V
-10
0.02
+10
-20
0.02
+20
VD = -10V,
VS = 10V
-10
-0.03
+10
-20
-0.03
+20
VD = 10V,
VS = -10V
-5
0.007
+5
-10
0.007
+10
VD = -10V,
VS = 10V
-5
-0.015
+5
-10
-0.015
+10
nA
nA
Monolithic CMOS Analog Multiplexers
DG506A/DG507A
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 15V, V- = -15V, VGND = 0V, TA = +25NC, unless otherwise indicated.)
PARAMETER
Channel
On-Leakage
Current
SYMBOL
ID(ON)
(Note 4)
CONDITIONS
DG506AA
DG507AA
MIN
TYP
(Note 2) (Note 3)
DG506AB/C
DG507AB/C
MAX
MIN
TYP
(Note 2) (Note 3)
UNITS
MAX
DG506A,
sequence each
switch on,
VAL = 0.8V,
VAH = 2.4V,
VEN = 2.4V
VS(all) = VD
= 10V
-10
0.03
+10
-20
0.03
+20
VS(all) = VD
= -10V
-10
-0.06
+10
-20
-0.06
+20
DG507A,
sequence each
switch on,
VAL = 0.8V,
VAH = 2.4V,
VEN = 2.4V
VS(all) = VD
= 10V
-5
0.015
+5
-10
0.015
+10
VS(all) = VD
= -10V
-5
-0.03
+5
-10
-0.03
+10
-10
-0.002
-10
-0.002
nA
INPUT
Address Input
Current, InputVoltage High
IAH
Address Input
Current, InputVoltage Low
IAL
VA = 2.4V
VA = 15V
All VA = 0V
0.006
10
0.006
VEN = 2.4V
-10
-0.002
-10
-0.002
VEN = 0V
-10
-0.002
-10
-0.002
10
FA
FA
DYNAMIC
Switching Time
of Multiplexer
ttransition
Figure 1
0.6
Break-BeforeMake Interval
tOPEN
Figure 3
Enable TurnOn Time
tON(EN)
Enable TurnOff Time
tOFF(EN)
Off-Isolation
(Note 5)
1
0.06
Fs
0.2
0.2
Fs
Figure 2
1
1
Fs
Figure 2
0.4
0.4
Fs
OIRR
VEN = 0V, RL = 1kI, CL =
15pF, VS = 7VRMS, f = 500kHz
68
68
dB
Source OffCapacitance
CS(OFF)
VEN = 0V, f = 140kHz, VS = 0V
6
6
pF
Drain OffCapacitance
CD(OFF)
VEN = 0V,
f = 140kHz
DG506A, VD = 0V
45
45
DG507A, VD = 0V
23
23
pF
SUPPLY
Positive Supply
Current
I+
Negative
Supply Current
I-
VEN = 0 or 5V, all VA = 0V
0.13
0.25
0.13
0.3
mA
VEN = 0 or 5V, all VA = 0V
-0.15
-0.07
-0.25
-0.07
3
DG506A/DG507A
Monolithic CMOS Analog Multiplexers
ELECTRICAL CHARACTERISTICS (Overtemperature)
(V+ = 15V, V- = -15V, VGND = 0V, TA = overtemperature range, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
DG506AA
DG507AA
MIN
TYP
(Note 2) (Note 3)
DG506AB/C
DG507AB/C
MAX
MIN
TYP
(Note 2) (Note 3)
UNITS
MAX
SWITCH
Analog Signal
Range
Drain-to-Source
On-Resistance
Source OffLeakage
Current
Drain OffLeakage
Current
Channel
On-Leakage
Current
VANALOG
RDS(ON)
IS(OFF)
-15
Sequence each
switch on,
VAL = 0.8V,
VAH = 2.4V,
VEN = 2.4V
-15
500
+15
I
VD = -10V,
IS = -200FA
500
550
-50
VS = -10V,
VD = 10V
-50
+50
-50
+50
VD = 10V,
VS = -10V
-300
+300
-300
+300
VD = -10V,
VS = 10V
-300
+300
-300
+300
VD = 10V,
VS = -10V
-200
+200
-200
+200
VD = -10V,
VS = 10V
-200
+200
-200
+200
DG506A,
sequence each
switch on,
VAL = 0.8V,
VAN = 2.4V,
VEN = 2.4V
VS(all) = VD
= 10V
-300
+300
-300
+300
VS(all) = VD
= -10V
-300
+300
-300
+300
DG507A,
sequence each
switch on,
VAL = 0.8V,
VAN = 2.4V,
VEN = 2.4V
VS(all) = VD
= 10V
-200
+200
-200
+200
VS(all) = VD
= -10V
-200
+200
-200
+200
ID(OFF)
DG507A,
VEN = 0.8V,
VAL = 0.8V
V
550
VS = 10V,
VD = -10V
VEN = 0.8V,
VAL = 0.8V
DG506A,
VEN = 0.8V,
VAL = 0.8V
ID(ON)
(Note 4)
VD = 10V, IS
= -200FA
+15
+50
-50
+50
nA
nA
nA
INPUT
4
Address Input
Current, InputVoltage High
IAH
Address Input
Current, InputVoltage Low
IAL
VA = 2.4V
-30
VA = 15V
All VA = 0V
-30
30
VEN = 2.4V
VEN = 0V
-30
30
FA
-30
30
30
FA
Monolithic CMOS Analog Multiplexers
(V+ = 15V, V- = -15V, VGND = 0V, TA = over temperature range, unless otherwise noted.)
Note 1: Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum
current ratings.
Note 2: The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is
used in this data sheet.
Note 3: Typical values are for design aid only, not guaranteed nor subject to production testing.
Note 4: ID(ON) is leakage from driver into on switch.
Note 5: Off-isolation = 20log x VO/VS, VS = input to off switch, VD = output due to VS.
Truth Tables
A3
A2
A1
A0
EN
ON SWITCH
A2
A1
A0
EN
ON SWITCH
X
X
X
X
0
None
X
X
X
0
None
0
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
2
0
0
1
1
2
0
0
1
0
1
3
0
1
0
1
3
0
0
1
1
1
4
0
1
1
1
4
0
1
0
0
1
5
1
0
0
1
5
0
1
0
1
1
6
1
0
1
1
6
0
1
1
0
1
7
1
1
0
1
7
0
1
1
1
1
8
1
1
1
1
8
1
0
0
0
1
9
1
0
0
1
1
10
1
0
1
0
1
11
1
0
1
1
1
12
1
1
0
0
1
13
1
1
0
1
1
14
1
1
1
0
1
15
1
1
1
1
1
16
Note: Logic “0” = VAL ≤ 0.8V, Logic “1” = VAH ≥ 2.4V,
“0” = Don’t Care.
Switching Time Test Circuits
+2.4V
+15V
EN
A3
A2
A1
A0
LOGIC
INPUT
V+
S1
S2 THRU S15
±10V
S16
D
±10V
DG506A
GND
+2.4V
V-
50Ω
-15V
Figure 1a. Transition Switching Time
1MΩ
+15V
EN
35pF
SWITCH
OUTPUT
VO
A2
A1
A0
LOGIC
INPUT
V+
S1b
S1a THRU S8a, Da
S2b, AND S7b
±10V
S8b
Db
±10V
DG507A
GND
V-
50Ω
1MΩ
35pF
SWITCH
OUTPUT
VO
-15V
Figure 1b. Transition Switching Time
5
DG506A/DG507A
ELECTRICAL CHARACTERISTICS (Overtemperature) (continued)
DG506A/DG507A
Monolithic CMOS Analog Multiplexers
Switching Time Test Circuits (continued)
+15V
EN
A3
A2
A1
A0
LOGIC
INPUT
50Ω
V+
-5V
S1
S2 THRU S16
DG506A
V-
GND
D
1kΩ
3V
50%
0
LOGIC INPUT
tr < 20ns
ti < 20ns
35pF
SWITCH
OUTPUT
VO
SWITCH OUTPUT
VO
(SEE FIGURE 1)
TRANSITION
TIME
-15V
VS1
0.8 VS1
0
0.8 VS8
VS8
ttransition
S1 ON
Figure 2a. Enable Switching Time
SWITCH OUTPUT
VO
(SEE FIGURE 2)
ENABLE t(ON)/t(OFF)
TIME
+15V
EN
A2
A1
A0
LOGIC
INPUT
50Ω
V+
-5V
S1b
S1a THRU S4a, Da,
S2b, S3b, S4b
DG507A
V-
GND
Db
1kΩ
35pF
SWITCH
OUTPUT
VO
-15V
OPEN TIME
BREAK-BEFORE-MAKE
INTERVAL
Figure 2b. Enable Switching Time
+2.4V
V+
ALL S AND Da
A0 A1 A2 A3
GND
Db, D
V-
50Ω
-15V
Figure 3. Break-Before-Make
6
toff (En)
0.9 VO
VO
VS
VS
50%
0V
tOPEN
Package Information
VS = +5V
DG506A
DG507A
LOGIC
INPUT
tON (En)
0
0.1 VO
Figure 4. Timing Diagrams for Figures 1, 2, and 3
+15V
EN
SWITCH OUTPUT
VO
(SEE FIGURE 3)
ttransition
S8 ON
1kΩ
35pF
SWITCH
OUTPUT
VO
For the latest package outline information and land patterns,
go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package
drawings may show a different suffix number, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
28 CERDIP
J28-2
21-0046
28 Plastic DIP
P28-2
21-0044
28 Wide SO
W28-5
21-0042
Monolithic CMOS Analog Multiplexers
REVISION
NUMBER
REVISION
DATE
0
8/92
Initial release
1
1/99
Updated to Word format.
2
5/09
Added ruggedized plastic part.
3
2/10
• Added lead temperature to the Absolute Maximum Ratings.
• Changed the derate rate of all packages to above 70°C in the Absolute
Maximum Ratings.
DESCRIPTION
PAGES
CHANGED
—
1–7
1–4, 7
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2010
Maxim Integrated Products 7
Maxim is a registered trademark of Maxim Integrated Products, Inc.
DG506A/DG507A
Revision History