MAXIM MAX6842FUKD3

19-2625; Rev 1; 2/03
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
The MAX6841/MAX6843 have an active-low push-pull
reset output. The MAX6841/MAX6842/MAX6844 have
an active-high push-pull reset output, and the
MAX6842/MAX6845 have an active-low open-drain
reset output. The active-low open-drain reset output
requires a pullup resistor that can be connected to a
voltage from 0 to VCC.
The low supply current (5.7µA) and small package
(SOT23-5) make the MAX6841–MAX6845 ideal for use
in portable equipment.
Applications
Computers
Controllers
Intelligent Instruments
Critical µP and µC Power Monitoring
Portable/Battery-Powered Equipment
Features
♦ Factory-Set Reset Threshold Voltages for
Monitoring Supplies from 0.9V to 1.5V
(MAX6841/MAX6842)
♦ Adjustable Threshold RESET IN
(MAX6843/MAX6844/MAX6845)
♦ Low Power Consumption: 5.7µA (typ)
♦ ±2.5% Reset Threshold Accuracy
Over Temperature
♦ Five Timeout Periods: 150µs (Voltage Detector
Version), 1.5ms, 30ms, 210ms, and 1.68s
♦ Available in Three Output Configurations
Push-Pull RESET
Push-Pull RESET
Open-Drain RESET
♦ Guaranteed Reset Valid to VCC = 0.55V
(Active Low)
♦ Manual Reset Input
♦ Immune to Short VCC Transients
♦ Space-Saving 5-Pin SOT23 Package
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX6841_UKD_-T
-40°C to +85°C
5 SOT23-5
MAX6842_UKD_-T
-40°C to +85°C
5 SOT23-5
MAX6843UKD_-T
-40°C to +85°C
5 SOT23-5
MAX6844UKD_-T
-40°C to +85°C
5 SOT23-5
MAX6845UKD_-T
-40°C to +85°C
5 SOT23-5
Note: Insert desired suffix letter (from the Threshold Suffix Guide
and the Active Timeout Period tables) into the blanks to complete the part number. For example, the MAX6842GUKD1 has a
reset threshold of 1.11V and a typical reset timeout period of
1.5ms. Sample stock is generally available on standard versions
only (see the Standard Versions table). Standard versions
require a minimum order increment of 2.5k units. Nonstandard
versions must be ordered in 10k-unit increments. Contact factory
for availability. All parts are offered in tape-and-reel only.
Pin Configurations
Telecom/Networking Equipment
Basestations
TOP VIEW
Servers/Workstations
RESET 1
GND 2
Selector Guide and Typical Operating Circuit appear at end
of data sheet.
5 VCC
MAX6841
MAX6842
GND 2
4 MR
RESET 3
SOT23-5
RESET
1
(RESET)
5 VCC
MAX6843
MAX6844
MAX6845
4 MR
RESET IN 3
SOT23-5
( ) ARE FOR 6844
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX6841–MAX6845
General Description
The MAX6841–MAX6845 microprocessor (µP) supervisory circuits monitor ultra-low-voltage power supplies in
µP and digital systems. They provide excellent circuit
reliability at low cost by eliminating external components and adjustments when used with +0.9V to +1.5V
systems. Factory-trimmed reset thresholds are available for the MAX6841/MAX6842. The MAX6843/
MAX6844/MAX6845 provide a RESET IN input, allowing
the user to externally adjust the reset threshold. The
MAX6841–MAX6845 family features a debounced manual reset input (MR). The reset comparator is designed
to ignore fast transients on VCC.
The MAX6841–MAX6845 assert a reset signal whenever the VCC supply voltage declines below a preset or
adjustable threshold or whenever manual reset (MR) is
asserted. Reset remains asserted for a fixed timeout
delay after VCC has risen above the reset threshold and
when manual reset is deasserted. Five timeout periods
are available for each part: 150µs (voltage detector version), 1.5ms, 30ms, 210ms, and 1.68s (typ).
MAX6841–MAX6845
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
ABSOLUTE MAXIMUM RATINGS
Terminal Voltage (with respect to GND)
VCC .......................................................................-0.3V to +6V
MR, RESET IN, RESET (open-drain).........................-0.3V to +6V
Push-Pull RESET and RESET .....................-0.3V to (VCC + 0.3V)
Input Current (all pins) ........................................................20mA
Output Current (RESET, RESET).........................................20mA
Continuous Power Dissipation (TA = +70°C)
5-Pin SOT23 (derate 7.1mW/°C above +70°C)............571mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +0.55V to +1.8V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Supply Voltage Range
VCC
Supply Current
ICC
CONDITIONS
MIN
VTH
RESET IN Threshold
VRSTIN
RESET IN Leakage Current
IRSTIN
Reset Threshold Hysteresis
VHYS
0.55
1.80
MAX6841/MAX6842/MAX6844 (Note 2)
0.75
1.80
VCC = 0.9V, no load, reset not asserted
5.7
20
VCC = 1.5V, no load, reset not asserted
7.3
20
MR Input Voltage (Note 3)
tRP
V
µA
8.1
20
1.350
1.388
1.425
H
1.275
1.313
1.350
G
1.080
1.110
1.140
F
1.020
1.050
1.080
E
0.810
0.833
0.855
D, TA = 0°C to +85°C
0.765
0.788
0.810
MAX6843/MAX6844/MAX6845 (Note 3)
181.2
187.4
191.5
mV
+25
nA
-25
0.75
µs
0.15
D1
1
1.5
2
D2
20
30
40
D3
140
210
280
D4
1120
1680
2240
0.3 × VCC
VIL
0.7 × VCC
VIH
V
%VTH
150
D0 (voltage detector)
Reset Active Timeout Period
UNITS
I
VCC falling, step signal from (VTH + 10%)
to (VTH - 10%) within 1µs
VCC or RESET IN to Reset Delay
MAX
MAX6843/MAX6845
VCC = 1.8V, no load, reset not asserted
Reset Threshold
(VCC Falling)
TYP
ms
V
MR Minimum Input Pulse Width
MR driven from VCC to 0 (Note 3)
MR Glitch Rejection
MR driven from VCC to 0 (Note 3)
150
ns
MR to Reset Delay
MR driven from VCC to 0 (Note 3)
500
ns
MR Pullup Resistance to VCC
2
1
10
µs
20
_______________________________________________________________________________________
26
kΩ
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
(VCC = +0.55V to +1.8V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Open-Drain RESET Output
Voltage
VOL
Open-Drain RESET Output
Leakage Current
ILKG
CONDITIONS
MIN
TYP
MAX
VCC ≥ 0.55V, ISINK = 10µA, reset asserted
0.2 × VCC
VCC ≥ 0.83V, ISINK = 80µA, reset asserted
0.2 × VCC
VCC > VTH, reset not asserted
VOL
Push-Pull RESET Output Voltage
VOH
VOH
Push-Pull RESET Output Voltage
V
1
VCC ≥ 0.55V, ISINK = 10µA, reset asserted
0.2 × VCC
VCC ≥ 0.83V, ISINK = 80µA, reset asserted
0.2 × VCC
VCC ≥ 0.83V, ISOURCE = 40µA, reset not
asserted
0.8 × VCC
VCC ≥ 0.75V, ISOURCE = 10µA, reset
asserted
0.8 × VCC
VCC ≥ 0.83V, ISOURCE = 40µA, reset
asserted
0.8 × VCC
µA
V
V
VCC ≥ 0.83V, ISINK = 80µA, reset not
asserted
VOL
UNITS
0.2 × VCC
Note 1: 100% production tested at +25°C. Overtemperature limits are guaranteed by design.
Note 2: The active-low output RESET has VCC(MIN) = 0.55V (MAX6841/MAX6842).
Note 3: For VCC > 0.788V, TA = 0°C to +85°C, and for VCC > 0.833V, TA = -40°C to +85°C.
Typical Operating Characteristics
(VCC = 1.5V, TA = +25°C, unless otherwise noted.)
POWER-DOWN RESET DELAY
vs. TEMPERATURE
VCC = 1.5V
6
5
VCC = 0.9V
4
3
2
300
VOD = 10mV
250
VOD = 20mV
200
150
100
VOD = 100mV
50
1
1.06
NORMALIZED RESET TIMEOUT PERIOD
7
350
MAX6841-45 toc02
VCC = 1.8V
POWER-DOWN RESET DELAY (µs)
SUPPLY CURRENT (µA)
8
MAX6841-45 toc01
9
NORMALIZED RESET TIMEOUT PERIOD
vs. TEMPERATURE
1.04
MAX6841-45 toc03
SUPPLY CURRENT
vs. TEMPERATURE
D2 OPTION
D3 OPTION
1.02
1.00
D4 OPTION
0.98
0.96
VOD = OVERDRIVE (mV)
0
0.94
0
-40
-20
0
20
40
TEMPERATURE (°C)
60
80
-40
-20
0
20
40
TEMPERATURE (°C)
60
80
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
_______________________________________________________________________________________
3
MAX6841–MAX6845
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics (continued)
(VCC = 1.5V, TA = +25°C, unless otherwise noted.)
NORMALIZED VCC RESET THRESHOLD
vs. TEMPERATURE
NORMALIZED RESET IN THRESHOLD
vs. TEMPERATURE
1.010
1.005
1.000
0.995
0.990
MAX6841-45 toc06
1.015
0.985
POWER-UP/POWER-DOWN
CHARACTERISTICS (MAX6843AUKD3)
MAX6841-45 toc05
VTH = 0.833V
NORMALIZED RESET IN THRESHOLD
MAX6841-45 toc04
1.015
NORMALIZED VCC RESET THRESHOLD
MAX6841–MAX6845
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
1.010
VCC
1V/div
1.005
1.000
RESET
1V/div
0.995
0.990
0.985
-40
-20
0
20
40
60
80
-40
-20
TEMPERATURE (°C)
0
20
40
60
200ms/div
80
TEMPERATURE (°C)
Pin Description
PIN
MAX6841
MAX6842
1
MAX6843
MAX6845
—
MAX6844
NAME
Push-Pull (MAX6841) or Open-Drain (MAX6842) Active-Low Reset Output. RESET
changes from high to low when VCC drops below the selected reset threshold or
MR is pulled low. RESET remains low for the reset timeout period after VCC
exceeds the device reset threshold and MR is released high.
—
RESET
—
1
—
2
2
2
3
—
GND
—
RESET
—
4
—
FUNCTION
1
Push-Pull (MAX6843) or Open-Drain (MAX6845) Active-Low Reset Output. RESET
changes from high to low when RESET IN drops below the 187.4mV reset
threshold (referenced to VCC) or MR is pulled low. RESET remains low for the
reset timeout period after RESET IN exceeds the reset threshold and MR is
released high.
Ground
Push-Pull Active-High Reset Output. RESET changes from low to high when VCC
input drops below the selected reset threshold or MR is pulled low. RESET
remains high for the reset timeout period after VCC exceeds the device reset
threshold and MR is released high.
Push-Pull Active-High Reset Output. RESET changes from low to high when the
RESET IN input drops below the 187.4mV reset threshold (referenced to VCC).
RESET remains high for the reset timeout period after RESET IN exceeds the reset
threshold.
Adjustable Reset Input. High-impedance input for reset comparator. Connect this
pin to an external resistive-divider network to set the reset threshold voltage; the
RESET IN typical threshold is 187.4mV (referenced to VCC). The MAX6843/MAX6844/
MAX6845 assert a reset signal when the VCC to RESET IN differential falls below
its threshold voltage.
—
3
3
4
4
4
MR
Active-Low Manual Reset Input. Internal 20kΩ pullup to VCC. Pull low to force a
reset. Reset remains active as long as MR is low and for the reset timeout period
after MR goes high. Leave unconnected or connect to VCC if unused.
5
5
5
VCC
Supply Voltage. Monitored supply for the MAX6841/MAX6842.
_______________________________________________________________________________________
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
MR
MR
VCC
VCC
MR
PULLUP
VREF
MANUAL
RESET
DETECT
MAX6841
MAX6842
MR
PULLUP
MANUAL
RESET
DETECT
VREF = 187.4mV
MAX6843
MAX6844
MAX6845
RESET IN
RESET
TIMEOUT
PERIOD
RESET
OUTPUT
RESET
TIMEOUT
PERIOD
RESET
RESET
RESET
OUTPUT
RESET
RESET
GND
GND
Detailed Description
Reset Output
A microprocessor’s (µP’s) reset input starts the µP in a
known state. The MAX6841–MAX6845 assert a reset during power-up, power-down, and brownout conditions.
When the VCC supply voltage falls below a preset threshold (MAX6841/MAX6842) or RESET IN falls below the
adjustable threshold (MAX6843/MAX6844/MAX6845),
reset asserts and stays asserted for a fixed timeout delay
(Table 2) after VCC or RESET IN has risen above the
reset threshold. The MAX6841–MAX6845 are available
with five typical timeout options for each part: 150µs
(voltage detector), 1.5ms, 30ms, 210ms, and 1.68s.
The MAX6841/MAX6842 have two reset outputs
(RESET and RESET); one is the inverse of the other.
The MAX6841 has one active-high push-pull output and
one active-low push-pull output. The MAX6842 has one
active-high push-pull output and one active-low opendrain output. The MAX6843 features an active-low
push-pull output. The MAX6844 features an activehigh push-pull output, and the MAX6845 has an activelow open-drain output stage. Connect a pullup resistor
from the open-drain RESET output to any voltage
between 0 and 6V.
tion, connect a normally open momentary switch from
MR to ground; external debounce circuitry is not
required. If MR is driven from long cables or the device
is used in a noisy environment, connect a 0.1µF capacitor from MR to ground to provide additional noise
immunity.
RESET IN
The MAX6843/MAX6844/MAX6845 feature a RESET IN
input, which allows users to adjust the reset threshold
voltage. The internal reference voltage is 187.4mV with
respect to VCC. An external resistive-divider network
can be used to set voltage monitoring thresholds, as
shown in Figure 1. The resistive-divider network must
be referenced to V CC . As V CC falls, the voltage at
VCC
R1
VCC
RESET IN
R2
MAX6843
MAX6844
MAX6845
Manual Reset Input
Many µP-based systems require a manual reset capability, allowing the operator, a test technician, or external logic circuitry to initiate a reset. Reset remains
asserted while MR is low, and for a fixed timeout delay
after MR returns high. This input has an internal 20kΩ
pullup resistor, so it can be left open if it is not used.
MR can be driven with CMOS logic level or with opendrain/collector outputs. To create a manual reset func-
MR
R1 =
R2
VCC-TH
-1
VREF
RESET
(RESET)
GND
( ) ARE FOR
MAX6844
WHERE VREF = 187.4mV (WITH RESPECT TO VCC) AND
VCC-TH IS THE VCC THRESHOLD.
Figure 1. Setting the Adjustable Threshold Externally
_______________________________________________________________________________________
5
MAX6841–MAX6845
Functional Diagrams
RESET IN decreases. The MAX6843/MAX6844/
MAX6845 assert a reset when the voltage at RESET IN
falls below the RESET IN threshold (VRSTIN). The lowleakage current at RESET IN allows for relatively largevalue resistors to be used, which reduces power
consumption. For example, for VCC-TH = 0.9V, if R2 =
100kΩ, then R1 = 26.3kΩ.
Applications Information
VCC Falling Transients
The MAX6841–MAX6845 are relatively immune to shortduration falling V CC transients (glitches). Figure 2
shows typical transient duration vs. reset comparator
overdrive, for which the MAX6841–MAX6845 do not
generate a reset pulse. The graph was generated using
a falling pulse applied to VCC, starting 0.1V above the
actual reset threshold and ending below it by the magnitude indicated (reset comparator overdrive). The
graph indicates the maximum pulse width that a falling
VCC transient can have without causing a reset pulse.
As the magnitude of the transient increases (goes further below the reset threshold), the maximum allowable
pulse width decreases. A 0.1µF bypass capacitor
mounted as close as possible to the VCC pin provides
additional transient immunity.
Ensuring a Valid Reset Output
Down to VCC = 0
When VCC falls below 0.55V, the MAX6841/MAX6843
push-pull RESET output no longer sinks current; it
becomes an open circuit. Therefore, high-impedance
CMOS-logic inputs connected to RESET can drift to
undetermined voltages. This presents no problem in
MAXIMUM TRANSIENT DURATION
vs. OVERDRIVE
most applications, because most µP and other circuitry
are inoperative with VCC lower than 0.55V. However, in
applications in which RESET must be valid down to 0,
adding a pulldown resistor to RESET causes any stray
leakage currents to flow to ground, holding RESET low
(Figure 3). R3’s value is not critical; 200kΩ is large
enough not to load RESET and small enough to pull
RESET to ground.
VCC
MAX6841
MAX6843
RESET
GND
R3
Figure 3. RESET Valid to VCC = 0
A 200kΩ pullup resistor to VCC is also recommended
for the MAX6841/MAX6842/MAX6844 if push-pull
RESET is required to remain valid for VCC ≤ 0.75V.
Interfacing to µPs with Bidirectional
Reset Pins
Because the RESET output on the MAX6842/MAX6845
is open drain, these devices interface easily with µPs
that have bidirectional reset pins. Connecting the µP
supervisor’s RESET output directly to the µP’s RESET
pin with a single pullup resistor allows either device to
assert reset (Figure 4).
600
MAXIMUM TRANSIENT DURATION (µs)
MAX6841–MAX6845
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
550
RESET OCCURS ABOVE THIS LINE
500
VCC
450
VCC
VCC
400
350
MAX6842
MAX6845
300
250
RESET
200
GND
150
µP
RESET
INPUT
GND
100
1
10
100
OVERDRIVE VTH - VCC (mV)
Figure 2. Maximum Transient Duration vs. Overdrive
6
Figure 4. Interfacing to Microprocessors with Bidirectional
Reset I/0
_______________________________________________________________________________________
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
VCC
Table 1. Threshold Suffix Guide
VCC
RPULLUP
MAX6842
MAX6845
µP
RESET
RESET
GND
MAX6841–MAX6845
+5.0V
0.9V
GND
SUFFIX
RESET THRESHOLD (V)
I
1.388
H
1.313
G
1.110
F
1.050
E
0.833
D
0.788
Table 2. Active Timeout Period Guide
Figure 5. Using the MAX6842/MAX6845 Open-Drain RESET
Output with Multiple Supplies
Using the MAX6842/MAX6845 Open-Drain
RESET Output with Multiple Supplies
Generally, the pullup connected to the MAX6842/
MAX6845 connects to the supply voltage being monitored at the IC’s VCC pin. However, some systems use
the open-drain output to level-shift from the monitored
supply to reset circuitry powered by some other supply
(Figure 5). Note that as the MAX6842/MAX6845’s VCC
decreases, so does the IC’s ability to sink current at
RESET. Also, with any pullup, RESET is pulled high as
VCC decays toward 0. The voltage where this occurs
depends on the pullup resistor value and the voltage to
which it is connected.
Chip Information
TRANSISTOR COUNT: 788
PROCESS: BiCMOS
SUFFIX
RESET ACTIVE TIMEOUT PERIOD (ms)
MIN
TYP
MAX
D0
—
0.15
—
D1
1
1.5
2
D2
20
30
40
D3
140
210
280
D4
1120
1680
2240
Table 3. Standard Versions
DEVICE
TOP MARK
MAX6841HUKD0
AEDR
MAX6841HUKD3
AEDS
MAX6841FUKD0
AEDP
MAX6841FUKD3
AEDQ
MAX6841DUKD0
AEDN
MAX6841DUKD3
AEDO
MAX6842HUKD0
AEDX
MAX6842HUKD3
AEDY
MAX6842FUKD0
AEDV
MAX6842FUKD3
AEDW
MAX6842DUKD0
AEDT
MAX6842DUKD3
AEDU
MAX6843UKD0
AEDZ
MAX6843UKD3
AEAV
MAX6844UKD0
AEEB
MAX6844UKD3
AEEC
MAX6845UKD0
AEAX
MAX6845UKD3
AEAY
_______________________________________________________________________________________
7
MAX6841–MAX6845
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
Selector Guide
PART
MANUAL RESET
ADJUSTABLE
RESET INPUT
PUSH-PULL
RESET
PUSH-PULL
RESET
OPEN-DRAIN
RESET
MAX6841
✔
—
✔
✔
—
MAX6842
✔
—
—
✔
✔
MAX6843
✔
✔
✔
—
—
MAX6844
✔
✔
—
✔
—
MAX6845
✔
✔
—
—
✔
Typical Operating Circuit
VIN
3.3V
0.9V
DC/DC
CONVERTER
CORE
SUPPLY
I/O
SUPPLY
VCC
µP
MAX6842D/E
RESET
PUSHBUTTON
SWITCH
MR
RESET
RESET
GND
GND
8
_______________________________________________________________________________________
Ultra-Low-Voltage µP Reset Circuits and
Voltage Detectors
SOT5L.EPS
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 9
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
MAX6841–MAX6845
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)