AD AD7475BRMZ

1 MSPS,12-Bit ADCs
AD7475/AD7495
FUNCTIONAL BLOCK DIAGRAMS
FEATURES AND APPLICATIONS
Fast throughput rate: 1 MSPS
Specified for VDD of 2.7 V to 5.25 V
Low power:
4.5 mW max at 1 MSPS with 3 V supplies
10.5 mW max at 1 MSPS with 5 V supplies
Wide input bandwidth:
68 dB SNR at 300 kHz input frequency
Flexible power/serial clock speed management
No pipeline delays
High speed serial interface:
SPI™-/QSPI™-/MICROWIRE™-/DSP-compatible
On-board reference: 2.5 V (AD7495 only)
Standby mode: 1 μA max
8-lead MSOP and SOIC packages
VDD
T/H
VIN
REF IN
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
SCLK
CONTROL
LOGIC
SDATA
CS
VDRIVE
AD7475
GND
VDD
VIN
Battery-powered systems
Personal digital assistants
Medical instruments
Mobile communications
Instrumentation and control systems
Data acquisition systems
Optical sensors
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
T/H
REF OUT
BUF
SCLK
CONTROL
LOGIC
2.5V
REFERENCE
SDATA
VDRIVE
AD7495
01684-B-001
CS
GND
GENERAL DESCRIPTION
The AD7475/AD74951 are 12-bit, high speed, low power,
successive-approximation ADCs that operate from a single
2.7 V to 5.25 V power supply with throughput rates up to
1 MSPS. They contain a low noise, wide bandwidth track-andhold amplifier that can handle input frequencies above 1 MHz.
The conversion process and data acquisition are controlled
using CS and the serial clock, allowing the devices to interface
with microprocessors or DSPs. The input signal is sampled on
the falling edge of CS and conversion is initiated at this point.
The conversion time is determined by the SCLK frequency.
There are no pipeline delays associated with the part.
Figure 1.
PRODUCT HIGHLIGHTS
1.
The AD7475 offers 1 MSPS throughput rates with 4.5 mW
power consumption.
2.
Single-supply operation with VDRIVE function. The
AD7475/AD7495 operate from a single 2.7 V to 5.25 V
supply. The VDRIVE function allows the serial interface
to connect directly to either 3 V or 5 V processor systems
independent of VDD.
3.
Flexible power/serial clock speed management. The conversion rate is determined by the serial clock, allowing the
conversion time to be reduced through the serial clock
speed increase. The parts also feature shutdown modes to
maximize power efficiency at lower throughput rates. This
allows the average power consumption to be reduced while
not converting. Power consumption is 1 μA when in full
shutdown.
4.
No pipeline delay. The parts feature a standard successive
approximation ADC with accurate control of the sampling
instant via a CS input and once-off conversion control.
The AD7475/AD7495 use advanced design techniques to
achieve very low power dissipation at high throughput rates.
With 3 V supplies and a 1 MSPS throughput rate, the AD7475
consumes just 1.5 mA, while the AD7495 consumes 2 mA.
With 5 V supplies and 1 MSPS, the current consumption is
2.1 mA for the AD7475 and 2.6 mA for the AD7495.
The analog input range for the parts is 0 V to REF IN. The 2.5 V
reference for the AD7475 is applied externally to the REF IN
pin, while the AD7495 has an on-board 2.5 V reference.
1
Protected by U.S. Patent No. 6,681,332
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
AD7475/AD7495
TABLE OF CONTENTS
AD7475 Specifications..................................................................... 3
Operating Modes............................................................................ 16
AD7495 Specifications..................................................................... 5
Normal Mode.............................................................................. 16
Timing Specifications....................................................................... 7
Partial Power-Down Mode ....................................................... 16
Timing Example 1 ........................................................................ 8
Full Power-Down Mode ............................................................ 17
Timing Example 2 ........................................................................ 8
Power vs. Throughput Rate....................................................... 19
Absolute Maximum Ratings............................................................ 9
Serial Interface ................................................................................ 20
ESD Caution.................................................................................. 9
Microprocessor Interfacing........................................................... 21
Pin Configuration and Function Descriptions........................... 10
AD7475/AD7495 to TMS320C5X/C54X ................................. 21
Terminology .................................................................................... 11
AD7475/AD7495 to ADSP-21XX ............................................. 21
Typical Performance Curves ......................................................... 12
AD7475/AD7495 to DSP56XXX ............................................... 22
Theory of Operation ...................................................................... 13
AD7475/AD7495 to MC68HC16............................................. 22
Converter Operation.................................................................. 13
Outline Dimensions ....................................................................... 23
ADC Transfer Function............................................................. 13
Ordering Guide .......................................................................... 24
Typical Connection Diagram ................................................... 14
REVISION HISTORY
5/05—Rev. A to Rev. B
Updated Format..................................................................Universal
Added Patent Information .............................................................. 1
Updated Outline Dimensions ....................................................... 23
Changes to Ordering Guide .......................................................... 24
Rev. B | Page 2 of 24
AD7475/AD7495
AD7475 SPECIFICATIONS
VDD = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, REF IN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise and Distortion
Ratio (SINAD)
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
(SFDR)
Intermodulation Distortion (IMD)
Second-Order Terms
Third-Order Terms
Aperture Delay
Aperture Jitter
Full Power Bandwidth
Full Power Bandwidth
DC ACCURACY
Resolution
Integral Nonlinearity
Differential Nonlinearity
Offset Error
Gain Error
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance
REFERENCE INPUT
REF IN Input Voltage Range
DC Leakage Current
Input Capacitance
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN 2
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
A Version 1
B Version1
Unit
Test Conditions/Comments
68
68
dB min
fIN = 300 kHz sine wave, fSAMPLE = 1 MSPS
−75
−76
−75
−76
dB max
dB max
fIN = 300 kHz sine wave, fSAMPLE = 1 MSPS
fIN = 300 kHz sine wave, fSAMPLE = 1 MSPS
−78
−78
10
50
8.3
1.3
−78
−78
10
50
8.3
1.3
dB typ
dB typ
ns typ
ps typ
MHz typ
MHz typ
@ 3 dB
@ 0.1 dB
12
±1.5
±0.5
+1.5/−0.9
12
±1
±0.5
+1.5/−0.9
Bits
LSB max
LSB typ
LSB max
±0.5
±8
±3
±0.5
±8
±3
LSB typ
LSB max
LSB max
±1
20
0 to REF IN
±1
20
@ 5 V (typ @ 3 V)
@ 25°C
@ 5 V guaranteed no missed codes to
12 bits (typ @ 3 V)
@ 25°C
Typically ±2.5 LSB
V
μA max
pF typ
2.5
±1
20
2.5
±1
20
V
μA max
pF typ
VDRIVE − 1
0.4
±1
10
VDRIVE − 1
0.4
±1
10
V min
V max
μA max
pF max
±1% for specified performance
Typically 10 nA, VIN = 0 V or VDRIVE
VDRIVE − 0.2
0.4
0.4
±10
±10
10
10
Straight (Natural) Binary
V min
V max
μA max
pF max
ISOURCE = 200 μA; VDRIVE = 2.7 V to 5.25 V
ISINK = 200 μA
800
300
325
1
ns max
ns max
ns max
MSPS max
16 SCLK cycles with SCLK at 20 MHz
Sine wave input
Full-scale step input
See the Serial Interface section
800
300
325
1
Rev. B | Page 3 of 24
AD7475/AD7495
Parameter
POWER REQUIREMENTS
VDD
VDRIVE
IDD 3
Normal Mode (Static)
Normal Mode (Operational)
Partial Power-Down Mode
Partial Power-Down Mode
Full Power-Down Mode
Power Dissipation
Normal Mode (Operational)
Partial Power-Down (Static)
Full Power-Down
A Version 1
B Version1
Unit
2.7/5.25
2.7/5.25
2.7/5.25
2.7/5.25
V min/max
V min/max
750
2.1
1.5
450
100
1
750
2.1
1.5
450
100
1
μA typ
mA max
mA max
μA typ
μA max
μA max
Digital inputs = 0 V or VDRIVE
VDD = 2.7 V to 5.25 V, SCLK on or off
VDD = 4.75 V to 5.25 V, fSAMPLE = 1 MSPS
VDD = 2.7 V to 3.6 V, fSAMPLE = 1 MSPS
fSAMPLE = 100 kSPS
Static
SCLK on or off
10.5
4.5
500
300
5
3
10.5
4.5
500
300
5
3
mW max
mW max
μW max
μW max
μW max
μW max
VDD = 5 V, fSAMPLE = 1 MSPS
VDD = 3 V, fSAMPLE = 1 MSPS
VDD = 5 V
VDD = 3 V
VDD = 5 V
VDD = 3 V
1
Temperature ranges for A, B versions: −40°C to +85°C.
Guaranteed by initial characterization.
3
See the Power vs. Throughput Rate section.
2
Rev. B | Page 4 of 24
Test Conditions/Comments
AD7475/AD7495
AD7495 SPECIFICATIONS
VDD = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise and Distortion (SINAD)
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
(SFDR)
Intermodulation Distortion (IMD)
Second-Order Terms
Third-Order Terms
Aperture Delay
Aperture Jitter
Full Power Bandwidth
Full Power Bandwidth
DC ACCURACY
Resolution
Integral Nonlinearity
Differential Nonlinearity
Offset Error
Gain Error
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance
REFERENCE OUTPUT
REF OUT Output Voltage
REF OUT Impedance
REF OUT Temperature Coefficient
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN 2
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
A Version 1
B Version1
Unit
Test Conditions/Comments
68
−75
−76
68
−75
−76
dB min
dB max
dB max
fIN = 300 kHz sine wave, fSAMPLE = 1 MSPS
fIN = 300 kHz sine wave, fSAMPLE = 1 MSPS
fIN = 300 kHz sine wave, fSAMPLE = 1 MSPS
−78
−78
10
50
8.3
1.3
−78
−78
10
50
8.3
1.3
dB typ
dB typ
ns typ
ps typ
MHz typ
MHz typ
@ 3 dB
@ 0.1 dB
12
±1.5
±0.5
+1.5/−0.9
12
±1
±0.5
+1.5/−0.9
Bits
LSB max
LSB typ
LSB max
±0.6
±8
±7
±0.6
±8
±7
LSB typ
LSB max
LSB max
0 to 2.5
±1
20
0 to 2.5
±1
20
V
μA max
pF typ
2.4625/2.5375
10
50
2.4625/2.5375
10
50
V min/max
Ω typ
ppm/°C typ
VDRIVE − 1
0.4
±1
10
VDRIVE − 1
0.4
±1
10
V min
V max
μA max
pF max
@ 5 V (typ @ 3 V)
@ 25°C
@ 5 V guaranteed no missed codes to
12 bits (typ @ 3 V)
@ 25°C
Typically ±2.5 LSB
Typically ±2.5 LSB
Typically 10 nA, VIN = 0 V or VDRIVE
VDRIVE − 0.2
0.4
0.4
±10
±10
10
10
Straight (Natural) Binary
V min
V max
μA max
pF max
ISOURCE = 200 μA; VDD = 2.7 V to 5.25 V
ISINK = 200 μA
800
300
325
1
ns max
ns max
ns max
MSPS max
16 SCLK cycles with SCLK at 20 MHz
Sine wave input
Full-scale step input
See the Serial Interface section
800
300
325
1
Rev. B | Page 5 of 24
AD7475/AD7495
Parameter
POWER REQUIREMENTS
VDD
VDRIVE
IDD
Normal Mode (Static)
Normal Mode (Operational)
Partial Power-Down Mode
Partial Power-Down Mode
Full Power-Down Mode
Power Dissipation 3
Normal Mode (Operational)
Partial Power-Down (Static)
Full Power-Down
A Version 1
B Version1
Unit
2.7/5.25
2.7/5.25
2.7/5.25
2.7/5.25
V min/max
V min/max
1
2.6
2
650
230
1
1
2.6
2
650
230
1
mA typ
mA max
mA max
μA typ
μA max
μA max
Digital inputs = 0 V or VDRIVE
VDD = 2.7 V to 5.25 V, SCLK on or off
VDD = 4.75 V to 5.25 V, fSAMPLE = 1 MSPS
VDD = 2.7 V to 3.6 V, fSAMPLE = 1 MSPS
fSAMPLE = 100 kSPS
Static
Static, SCLK on or off
13
6
1.15
690
5
3
13
6
1.15
690
5
3
mW max
mW max
mW max
μW max
μW max
μW max
VDD = 5 V, fSAMPLE = 1 MSPS
VDD = 3 V, fSAMPLE = 1 MSPS
VDD = 5 V
VDD = 3 V
VDD = 5 V
VDD = 3 V
1
Temperature ranges for A, B versions: −40°C to +85°C.
Guaranteed by initial characterization.
3
See the Power vs. Throughput Rate section.
2
Rev. B | Page 6 of 24
Test Conditions/Comments
AD7475/AD7495
TIMING SPECIFICATIONS 1
VDD = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, REF IN = 2.5 V (AD7475), TA = TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter
fSCLK 2
tCONVERT
tQUIET
t2
t3 3
t4
t5
t6
t7
t8 4
t9
tPOWER-UP
Limit at TMIN, TMAX
10
20
16 × tSCLK
800
100
10
22
40
0.4 tSCLK
0.4 tSCLK
10
10
45
20
20
650
Unit
kHz min
MHz max
ns max
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns min
ns max
ns max
μs max
μs max
Description
tSCLK = 1/fSCLK
fSCLK = 20 MHz
Minimum quiet time required between conversions
CS to SCLK setup time
Delay from CS until SDATA three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time
SCLK falling edge to SDATA high impedance
SCLK falling edge to SDATA high impedance
CS rising edge to SDATA high impedance
Power-up time from full power-down (AD7475)
Power-up time from full power-down (AD7495)
1
Guaranteed by initial characterization. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDRIVE) and timed from a voltage level of 1.6 V.
Mark/space ratio for the SCLK input is 40/60 to 60/40.
3
Measured with the load circuit of Figure 4 and defined as the time required for the output to cross 0.8 V or 2.0 V.
4
t8 and t9 are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 4. The measured number is
extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times, t8 and t9, quoted in the timing characteristics are
the true bus relinquish times of the part and are independent of the bus loading.
2
Rev. B | Page 7 of 24
AD7475/AD7495
TIMING EXAMPLE 1
TIMING EXAMPLE 2
With fSCLK = 20 MHz and a throughput of 1 MSPS, the cycle
time is t2 + 12.5(1/fSCLK) + tACQ = 1 μs. With t2 = 10 ns min, tACQ
is 365 ns. The 365 ns satisfies the requirement of 300 ns for tACQ.
In Figure 3, tACQ comprises 2.5(1/fSCLK) + t8 + tQUIET, where t8 =
45 ns. This allows a value of 195 ns for tQUIET, satisfying the
minimum requirement of 100 ns.
With fSCLK = 5 MHz and a throughput of 315 KSPS, the cycle
time is t2 + 12.5(1/fSCLK) + tACQ = 3.174 μs. With t2 = 10 ns min,
tACQ is 664 ns. The 664 ns satisfies the requirement of 300 ns for
tACQ. In Figure 3, tACQ comprises 2.5(1/fSCLK) + t8 + tQUIET, where
t8 = 45 ns. This allows a value of 119 ns for tQUIET, satisfying the
minimum requirement of 100 ns. As in this example and with
other slower clock values, the signal may already be acquired
before the conversion is complete, but it is still necessary
to leave 100 ns minimum tQUIET between conversions. In
Example 2, the signal should be fully acquired at approximately
Point C in Figure 3.
CS
tCONVERT
t6
1
4
3
2
B
5
13
15
14
t5
t7
t8
t4
t3
0
SDATA
THREE-STATE
0
0
0
DB11
DB10
tQUIET
DB0
DB1
DB2
16
01684-B-002
t2
SCLK
THREE-STATE
FOUR LEADING ZEROS
Figure 2. Serial Interface Timing Diagram
CS
tCONVERT
t6
t2
2
3
B
5
4
C
13
14
15
t5
16
t8
tQUIET
12.5 (1/fSCLK)
tACQUISITION
10ns
1/THROUGHPUT
Figure 3. Serial Interface Timing Example
200μA
TO OUTPUT
PIN
IOL
1.6V
CL
50pF
200μA
IOH
Figure 4. Load Circuit for Digital Output Timing Specifications
Rev. B | Page 8 of 24
01684-B-003
45ns
01684-B-004
SCLK
1
AD7475/AD7495
ABSOLUTE MAXIMUM RATINGS
TA = 25°C unless otherwise noted.
Table 4.
Parameters
VDD to GND
VDRIVE to GND
Analog Input Voltage to GND
Digital Input Voltage to GND
VDRIVE to VDD
Digital Output Voltage to GND
REF IN to GND
Input Current to Any Pin Except
Supplies 1
Operating Temperature Range
Commercial (A, B Version)
Storage Temperature Range
Junction Temperature
SOIC, MSOP Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
ESD
1
Ratings
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDD + 0.3 V
±10 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
−40°C to +85°C
−65°C to +150°C
150°C
450 mW
157°C/W (SOIC)
205.9°C/W (MSOP)
56°C/W (SOIC)
43.74°C/W (MSOP)
215°C
220°C
4 kV
Transient currents of up to 100 mA do not cause SCR latch-up.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 9 of 24
AD7475/AD7495
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
REF IN 1
8 VDD
AD7475
7 CS
TOP VIEW
GND 3 (Not to Scale) 6 VDRIVE
5 SDATA
SCLK 4
01684-B-005
VIN 2
Figure 5. AD7475 SOIC/MSOP Pin Configuration
REF OUT 1
8 VDD
AD7495
7 CS
TOP VIEW
GND 3 (Not to Scale) 6 VDRIVE
SCLK 4
5 SDATA
01684-B-006
VIN 2
Figure 6. AD7495 SOIC/MSOP Pin Configuration
Table 5. Pin Descriptions
Pin No.
1 (AD7475)
Mnemonic
REF IN
1 (AD7495)
REF OUT
2
3
VIN
GND
4
SCLK
5
SDATA
6
VDRIVE
7
CS
8
VDD
Function
Reference Input for the AD7475. An external reference must be applied to this input. The voltage range for
the external reference is 2.5 V ± 1% for specified performance. A cap of a least 0.1 μF should be placed on the
REF IN pin.
Reference Output for the AD7495. A minimum 100 nF capacitance is required from this pin to GND. The
internal reference can be taken from this pin, but buffering is required before it is applied elsewhere in a
system.
Analog Input. Single-ended analog input channel. The input range is 0 to REF IN.
Analog Ground. Ground reference point for all circuitry on the AD7475/AD7495. All analog input signals and
any external reference signal should be referred to this GND voltage.
Serial Clock, Logic Input. SCLK provides the serial clock for accessing data from the part. This clock input is
also used as the clock source for the AD7475/AD7495 conversion process.
Data Out, Logic Output. The conversion result from the AD7475/AD7495 is provided on this output as a serial
data stream. The bits are clocked out on the falling edge of the SCLK input. The data stream consists of four
leading zeros followed by the 12 bits of conversion data, which is provided MSB first.
Logic Power Supply Input. The voltage supplied at this pin determines the operating voltage for the serial
interface of the AD7475/AD7495.
Chip Select, Active Low Logic Input. This input provides the dual function of initiating conversions on the
AD7475/AD7495 and also frames the serial data transfer.
Power Supply Input. The VDD range for the AD7475/AD7495 is from 2.7 V to 5.25 V.
Rev. B | Page 10 of 24
AD7475/AD7495
TERMINOLOGY
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. The endpoints of
the transfer function are zero scale, a point ½ LSB below the
first code transition, and full scale, a point ½ LSB above the last
code transition.
Total Harmonic Distortion (THD)
The ratio of the rms sum of harmonics to the fundamental. For
the AD7475/AD7495, THD is defined as
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Offset Error
The deviation of the first code transition (00 . . . 000) to
(00 . . . 001) from the ideal, that is, AGND + 0.5 LSB.
Peak Harmonic or Spurious Noise
The ratio of the rms value of the next largest component in
the ADC output spectrum (up to fS/2 and excluding dc) to
the rms value of the fundamental. Normally, the value of this
specification is determined by the largest harmonic in the
spectrum, but for ADCs where the harmonics are buried in
the noise floor, it is a noise peak.
Gain Error
This is the deviation of the last code transition (111. . . 110) to
(111. . . 111) from the ideal (that is, VREF − 1.5 LSB) after the
offset error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns into track mode on the
13th SCLK rising edge (see the Serial Interface section). The
track-and-hold acquisition time is the minimum time required
for the track-and-hold amplifier to remain in track mode for its
output to reach and settle to within 0.5 LSB of the applied input
signal, given a step change to the input signal.
Signal-to-Noise and Distortion Ratio (SINAD)
The measured ratio of signal-to-noise and distortion at the
output of the analog-to-digital converter (ADC). The signal is
the rms amplitude of the fundamental. Noise is the sum of all
nonfundamental signals up to half the sampling frequency
(fS/2), excluding dc. The ratio is dependent on the number of
quantization levels in the digitization process; the more levels,
the smaller the quantization noise. The theoretical SINAD ratio
for an ideal N-bit converter with a sine wave input is given by
Signal to (Noise + Distortion ) = (6.02 N + 1.76) dB
THD (dB) = 20 log
V2 2 + V3 2 + V4 2 + V5 2 +V6 2
V1
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation distortion terms are those
for which neither m nor n is equal to zero. For example, the
second-order terms include (fa + fb) and (fa − fb), while the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
The AD7475/AD7495 are tested using the CCIF standard where
two input frequencies near the top end of the input bandwidth
are used. In this case, the second-order terms are usually
distanced in frequency from the original sine waves while the
third order terms are usually at a frequency close to the input
frequencies. As a result, the second- and third-order terms are
specified separately. Like THD, intermodulation distortion is
calculated as the rms sum of the individual distortion products
to the rms amplitude of the sum of the fundamentals, expressed
in dBs.
For a 12-bit converter, the SINAD is 74 dB.
Rev. B | Page 11 of 24
AD7475/AD7495
TYPICAL PERFORMANCE CURVES
Figure 7 shows a typical FFT plot for the AD7475 at a 1 MHz
sample rate and a 100 kHz input frequency.
8192 POINT FFT
fSAMPLE = 1MSPS
fIN = 100kHz
SINAD = 70.46dB
THD = –87.7dB
SFDR = –89.5dB
–15
–35
71.0
VDD = VDRIVE = 4.75V
70.5
VDD = VDRIVE = 3.60V
–55
SINAD (dB)
SINAD (dB)
Figure 9 shows the SINAD performance vs. input frequency for
various supply voltages while sampling at 1 MSPS with an SCLK
of 20 MHz.
–75
70.0
VDD = VDRIVE = 2.70V
69.5
VDD = VDRIVE = 5.25V
–95
50
100
150
200 250 300
350
FREQUENCY (kHz)
400
450
500
68.5
Figure 7. AD7475 Dynamic Performance
Figure 8 shows a typical FFT plot for the AD7495 at a 1 MHz
sample rate and a 100 kHz input frequency.
8192 POINT FFT
fSAMPLE = 1MSPS
fIN = 100kHz
SINAD = 69.95dB
THD = –89.2dB
SFDR = –91.2dB
–15
SINAD (dB)
–35
–55
–75
–115
0
50
100
150
200 250 300
350
FREQUENCY (kHz)
400
450
500
01684-B-008
–95
Figure 8. AD7495 Dynamic Performance
Rev. B | Page 12 of 24
10
100
INPUT FREQUENCY (kHz)
1000
Figure 9. AD7495 SINAD vs. Input Frequency at 1 MSPS
01684-B-009
0
01684-B-007
69.0
–115
AD7475/AD7495
THEORY OF OPERATION
The AD7475/AD7495 also feature power-down options to allow
power saving between conversions. The power-down feature is
implemented across the standard serial interface, as described
in the Operating Modes section.
CONVERTER OPERATION
The AD7475/AD7495 are 12-bit, successive approximation
analog-to-digital converters based around a capacitive DAC.
The AD7475/AD7495 can convert analog input signals in the
range 0 V to 2.5 V. Figure 10 and Figure 12 show simplified
schematics of the ADC. The ADC comprises control logic, SAR,
and a capacitive DAC, which are used to add and subtract fixed
amounts of charge from the sampling capacitor to bring the
comparator back into a balanced condition. Figure 10 shows the
ADC during its acquisition phase. SW2 is closed and SW1 is in
Position A. The comparator is held in a balanced condition and
the sampling capacitor acquires the signal on VIN.
CAPACITIVE
DAC
COMPARATOR
AGND
Figure 11. ADC Conversion Phase
ADC TRANSFER FUNCTION
The output coding of the AD7475/AD7495 is straight binary.
The designed code transitions occur midway between
successive LSB integer values (that is, ½ LSB, 3/2 LSBs, etc.). The
LSB size is = VREF/4096. The ideal transfer characteristic for the
AD7475/AD7495 is shown in Figure 12.
111...111
111...110
111...000
1LSB = VREF/4096
011...111
000...010
000...001
000...000
0V 0.5LSB
VREF –1.5LSB
ANALOG INPUT
CONTROL LOGIC
COMPARATOR
01684-B-010
Figure 12. AD7475/AD7495 Transfer Characteristic
B
SW2
AGND
CONTROL LOGIC
SW2
4kΩ
A
SW1
B
01684-B-011
SW1
CAPACITIVE
DAC
VIN
4kΩ
A
VIN
Figure 10. ADC Acquisition Phase
Rev. B | Page 13 of 24
01684-B-012
The AD7475/AD7495 ADCs have an on-chip track-and-hold
with a serial interface housed in either an 8-lead SOIC_N or
MINI_SO package, features that offer the user considerable
space-saving advantages over alternative solutions. The AD7495
also has an on-chip 2.5 V reference. The serial clock input
accesses data from the part but also provides the clock source
for the successive-approximation ADC. The analog input range
is 0 V to REF IN for the AD7475 and 0 V to REF OUT for the
AD7495.
When the ADC starts a conversion (see Figure 11), SW2 opens
and SW1 moves to Position B causing the comparator to
become unbalanced. The control logic and the capacitive DAC
are used to add and subtract fixed amounts of charge from the
sampling capacitor to bring the comparator back into a
balanced condition. When the comparator is rebalanced, the
conversion is complete. The control logic generates the ADC
output code.
ADC CODE
The AD7475/AD7495 are fast, micropower, 12-bit, singlesupply analog-to-digital converters (ADCs). The parts can be
operated from a 2.7 V to 5.25 V supply. When operated from
either a 5 V supply or a 3 V supply, the AD7475/AD7495 are
capable of throughput rates of 1 MSPS when provided with a
20 MHz clock.
AD7475/AD7495
TYPICAL CONNECTION DIAGRAM
Analog Input
Figure 13 and Figure 15 show typical connection diagrams for
the AD7475 and AD7495, respectively. In both setups the GND
pin is connected to the analog ground plane of the system. In
Figure 13, REF IN is connected to a decoupled 2.5 V supply
from a reference source, the AD780, to provide an analog input
range of 0 V to 2.5 V. Although the AD7475 is connected to a
VDD of 5 V, the serial interface is connected to a 3 V microprocessor. The VDRIVE pin of the AD7475 is connected to the
same 3 V supply of the microprocessor to allow a 3 V logic
interface (see the Digital Inputs section.) In Figure 15, the REF
OUT pin of the AD7495 is connected to a buffer and then
applied to a level-shifting circuit used on the analog input to
allow a bipolar signal to be applied to the AD7495. A minimum
100 nF capacitance is required on the REF OUT pin to GND.
The conversion result from both ADCs is output in a 16-bit
word with four leading zeros followed by the MSB of the 12-bit
result. For applications where power consumption is of concern,
the power-down modes should be used between conversions or
bursts of several conversions to improve power performance.
See the Operating Modes section for more information.
Figure 14 shows an equivalent circuit of the analog input
structure of the AD7475/AD7495. The D1 and D2 diodes
provide ESD protection for the analog inputs. Care must be
taken to ensure that the analog input signal never exceeds the
supply rails by more than 200 mV. This causes these diodes to
become forward-biased and start conducting current into the
substrate. The maximum current these diodes can conduct
without causing irreversible damage to the part is 20 mA.
The capacitor C1 in Figure 14 is typically about 4 pF and can
primarily be attributed to pin capacitance. The resistor R1 is a
lumped component made up of the on resistance of a switch.
This resistor is typically about 100 Ω. The capacitor C2 is
the ADC sampling capacitor and has a capacitance of 16 pF,
typically. For ac applications, it is recommended to remove
high frequency components from the analog input signal
using an RC low-pass filter on the relevant analog input pin. In
applications where harmonic distortion and signal-to-noise
ratio are critical, the analog input should be driven from a low
impedance source. Large source impedances significantly affect
the ac performance of the ADC. This may necessitate the use of
an input buffer amplifier. The choice of the op amp is a function
of the particular application.
0.1μF
5V
SUPPLY
10μF
VDD
μC/μP
VIN
C1
4pF
CS
GND
0.1μF
3V
SUPPLY
C2
16pF
CONVERSION PHASE: SWITCH OPEN
TRACK PHASE: SWITCH CLOSED
10μF
2.5V
AD780
R1
D2
VDRIVE
REF IN
Figure 14. Equivalent Analog Input Circuit
Figure 13. AD7475 Typical Connection Diagram
0.1μF
10μF
5V
SUPPLY
SERIAL
INTERFACE
V
0V
V
R
0V TO
2.5V
INPUT
R
3R
VDD
SCLK
VIN
AD7495
SDATA
μC/μP
CS
R
GND
VDRIVE
REF OUT
0.1μF
0.1μF
(MIN)
Figure 15. AD7495 Typical Connection Diagram
Rev. B | Page 14 of 24
10μF
3V
SUPPLY
01684-B-015
0.1μF
(MIN)
D1
SDATA
AD7475
01684-B-013
VIN
SCLK
01684-B-014
VDD
0V TO
2.5V
INPUT
SERIAL
INTERFACE
AD7475/AD7495
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance depends on the amount of total harmonic
distortion (THD) that can be tolerated. The THD increases as
the source impedance increases and performance degrades.
Figure 16 shows a graph of the total harmonic distortion vs.
source impedance for various analog input frequencies.
–10
–20
–30
fIN = 10kHz
THD (dB)
–40
fIN = 500kHz
fIN = 200kHz
–60
–70
fIN = 100kHz
10
100
SOURCE IMPEDANCE (Ω)
1000
01684-B-016
–80
1
10000
Figure 16. THD vs. Source Impedance for Various Analog Input Frequencies
Figure 17 shows a graph of total harmonic distortion vs. analog
input frequency for various supply voltages while sampling at
1 MSPS with an SCLK of 20 MHz.
–75
VDD = VDRIVE = 5.25V
–77
VDD = VDRIVE = 2.70V
–79
–81
THD (dB)
The AD7475/AD7495 also has the VDRIVE feature. This feature
controls the voltage at which the serial interface operates. VDRIVE
allows the ADC to easily interface to both 3 V and 5 V
processors.
For example, if the AD7475/AD7495 were operated with a VDD
of 5 V, the VDRIVE pin could be powered from a 3 V supply. The
AD7475/AD7495 have better dynamic performance with a VDD
of 5 V, while still being able to interface to 3 V digital parts.
Care should be taken to ensure VDRIVE does not exceed VDD by
more than 0.3 V. (See the Absolute Maximum Ratings section.)
Reference Section
–50
–90
VDRIVE
An external reference source should be used to supply the 2.5 V
reference to the AD7475. Errors in the reference source result
in gain errors in the AD7475 transfer function and add the
specified full-scale errors on the part. The AD7475 voltage
reference input, REF IN, has a dynamic input impedance. A
small dynamic current is required to charge the capacitors in
the capacitive DAC during the bit trials. This current is typically
50 μA for a 2.5 V reference. A capacitor of at least 0.1 μF should
be placed on the REF IN pin. Suitable reference sources for the
AD7475 are the AD780, AD680, AD1582, ADR391, ADR381,
ADR431, and ADR03.
The AD7495 contains an on-chip 2.5 V reference. As shown in
Figure 18, the voltage that appears at the REF OUT pin is
internally buffered before being applied to the ADC; the output
impedance of this buffer is typically 10 Ω. The reference is
capable of sourcing up to 2 mA. The REF OUT pin should be
decoupled to AGND using a 100 nF or greater capacitor.
–83
If the 2.5 V internal reference is used to drive another device
that is capable of glitching the reference at critical times, then
the reference has to be buffered before driving the device. To
ensure optimum performance of the AD7495, it is recommended that the internal reference not be over driven. If an
ADC with external reference capability is required, the AD7475
should be used.
VDD = VDRIVE = 3.60V
–85
–87
VDD = VDRIVE = 4.75V
–89
–91
–95
10
100
INPUT FREQUENCY (kHz)
1000
01684-B-017
–93
Figure 17. THD vs. Analog Input Frequency for Various Supply Voltages
V
REF OUT
Digital Inputs
The digital inputs applied to the AD7475/AD7495 are not
limited by the maximum ratings, which limit the analog inputs.
Instead, the digital inputs applied can go to 7 V and are not
restricted by the VDD + 0.3 V limit as on the analog inputs.
Another advantage of SCLK and CS not being restricted by the
VDD + 0.3 V limit is that power supply sequencing issues are
avoided. If CS or SCLK are applied before VDD, there is no risk
of latch-up as there would be on the analog inputs if a signal
greater than 0.3 V were applied prior to VDD.
Rev. B | Page 15 of 24
160kΩ
40kΩ
Figure 18. AD7495 Reference Circuit
01684-B-018
25Ω
AD7475/AD7495
OPERATING MODES
The AD7475/AD7495 operating mode is selected by controlling
the logic state of the CS signal during a conversion. There are
three possible modes of operation: normal mode, partial powerdown mode, and full power-down mode. The point at which CS
is pulled high after the conversion has been initiated determines
which power-down mode, if any, the device enters. Similarly, if
already in a power-down mode, CS can control whether the
device returns to normal operation or remains in power-down.
These modes of operation are designed to provide flexible
power management options. These options can be chosen to
optimize the power dissipation/throughput rate ratio for
differing application requirements.
NORMAL MODE
This mode is intended for fastest throughput rate performance,
because the user does not have to worry about any power-up
times with the AD7475/AD7495 remaining fully powered all
the time. Figure 19 shows the general diagram of the AD7475/
AD7495 operating in this mode.
The conversion is initiated on the falling edge of CS, as
described in the Serial Interface section. To ensure the part
remains fully powered-up at all times, CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high any time after the 10th SCLK falling
edge, but before the 16th SCLK falling edge, the part remains
powered up but the conversion is terminated and SDATA goes
back into three-state. Sixteen serial clock cycles are required to
complete the conversion and access the conversion result. CS
may idle high until the next conversion or may idle low until
sometime prior to the next conversion (effectively idling CS
low).
Once a data transfer is complete (SDATA has returned to threestate), another conversion can be initiated after the quiet time,
tQUIET, has elapsed, by bringing CS low again.
PARTIAL POWER-DOWN MODE
This mode is intended for use in applications where slower
throughput rates are required; either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and then the ADC is
powered down for a relatively long duration between these
bursts of several conversions. When the AD7475 is in partial
power-down, all analog circuitry is powered down except for
the bias current generator; and, in the case of the AD7495, all
analog circuitry is powered down except for the on-chip
reference and reference buffer.
To enter partial power-down, the conversion process must be
interrupted by bringing CS high anywhere after the second
falling edge of SCLK and before the tenth falling edge of SCLK,
as shown in Figure 20. Once CS has been brought high in this
window of SCLKs, the part enters partial power-down, the
conversion that was initiated by the falling edge of CS is
terminated, and SDATA goes back into three-state. If CS is
brought high before the second SCLK falling edge, the part
remains in normal mode and does not power down. This avoids
accidental power-down due to glitches on the CS line.
CS
1
10
16
SDATA
01684-B-019
SCLK
FOUR LEADING ZEROS + CONVERSION RESULT
Figure 19. Normal Mode
CS
2
10
16
01684-B-020
1
SCLK
Figure 20. Entering Partial Power-Down Mode
Rev. B | Page 16 of 24
AD7475/AD7495
To exit this operating mode and power up the AD7475/AD7495
again, a dummy conversion is performed. On the falling edge of
CS, the device begins to power up and continues to power up as
long as CS is held low until after the falling edge of the tenth
SCLK. The device is fully powered up once 16 SCLKs have
elapsed, and valid data results from the next conversion, as
shown in Figure 21. If CS is brought high before the second
falling edge of SCLK, the AD7475/AD7495 go back into partial
power-down again. This avoids accidental power-up due to
glitches on the CS line; although the device may begin to power
up on the falling edge of CS, it powers down again on the rising
edge of CS. If in partial power-down and CS is brought high
between the second and tenth falling edges of SCLK, the device
enters full power-down mode.
Power-Up Time
The power-up time of the AD7475/AD7495 from partial
power-down is typically 1 μs, which means that with any
frequency of SCLK up to 20 MHz, one dummy cycle is
sufficient to allow the device to power up from partial powerdown. Once the dummy cycle is complete, the ADC is fully
powered up and the input signal is acquired properly. The quiet
time, tQUIET, must still be allowed from the point where the bus
goes back into three-state after the dummy conversion to the
next falling edge of CS. When running at a 1 MSPS throughput
rate, the AD7475/AD7495 power up and acquire a signal within
±0.5 LSB in one dummy cycle, 1 μs.
THE PART BEGINS
TO POWER UP
When powering up from the power-down mode with a dummy
cycle, as in Figure 21, the track-and-hold that was in hold mode
while the part was powered down returns to track mode after
the first SCLK edge the part receives after the falling edge of CS.
This is shown as Point A in Figure 21. Although at any SCLK
frequency one dummy cycle is sufficient to power up the device
and acquire VIN, it does not necessarily mean that a full dummy
cycle of 16 SCLKs must always elapse to power up the device
and fully acquire VIN; 1 μs is sufficient to power up the device
and acquire the input signal. If, for example, a 5 MHz SCLK
frequency were applied to the ADC, the cycle time would be
3.2 μs. In one dummy cycle, 3.2 μs, the part would be powered
up and VIN fully acquired. However, after 1 μs with a 5 MHz
SCLK, only 5 SCLK cycles would have elapsed. At this stage,
the ADC would be fully powered up and the signal acquired.
In this case, the CS can be brought high after the tenth SCLK
falling edge and brought low again after a time, tQUIET, to initiate
the conversion.
FULL POWER-DOWN MODE
Full power-down mode is intended for use in applications
where slower throughput rates are required than that in the
partial power-down mode, because power up from a full powerdown would not be complete in just one dummy conversion.
This mode is more suited to applications where a series of
conversions performed at a relatively high throughput rate are
followed by a long period of inactivity and therefore power
down. When the AD7475/AD7495 are in full power-down, all
analog circuitry is powered down.
THE PART IS FULLY
POWERED UP
CS
A1
16
10
16
1
SDATA
INVALID DATA
01684-B-021
SCLK
VALID DATA
Figure 21. Exiting Partial Power-Down Mode
THE PART BEGINS
TO POWER UP
THE PART ENTERS
PARTIAL POWER-DOWN
THE PART ENTERS
FULL POWER-DOWN
CS
1
2
16
10
1
2
10
16
SDATA
INVALID DATA
THREE-STATE
THREE-STATE
INVALID DATA
Figure 22. Entering Full Power-Down Mode
Rev. B | Page 17 of 24
01684-B-023
SCLK
AD7475/AD7495
Full power-down is entered in a way similar to partial powerdown, except the timing sequence shown in Figure 20 must be
executed twice. The conversion process must be interrupted in a
similar fashion by bringing CS high anywhere after the second
falling edge of SCLK and before the tenth falling edge of SCLK.
The device enters partial power-down at this point. To reach
full power-down, the next conversion cycle must be interrupted
in the same way, as shown in Figure 22. Once CS has been
brought high in this window of SCLKs, then the part powers
down completely.
Note that it is not necessary to complete the 16 SCLKs once CS
has been brought high to enter a power-down mode.
To exit full power-down, and power up the AD7475/AD7495
again, a dummy conversion is performed as when powering up
from partial power-down. On the falling edge of CS, the device
begins to power up and continues to power up as long as CS is
held low until after the falling edge of the tenth SCLK. The
power-up time is longer than one dummy conversion cycle
however, and this time, tPOWER-UP, must elapse before a
conversion can be initiated, as shown in Figure 23. See the
Timing Specifications section for more information.
When power supplies are first applied to the AD7475/AD7495,
the ADC may power up in either of the power-down modes
or normal mode. Because of this, it is best to allow a dummy
cycle to elapse to ensure the part is fully powered up before
attempting a valid conversion. Likewise, if the intent is to keep
the part in partial power-down mode immediately after the
supplies are applied, then two dummy cycles must be initiated.
The first dummy cycle must hold CS low until after the tenth
THE PART BEGINS
TO POWER UP
SCLK falling edge, as shown in Figure 19. In the second cycle,
CS must be brought high before the tenth SCLK edge, but
after the second SCLK falling edge, as shown in Figure 20.
Alternatively, if the intent is to place the part in full powerdown mode when the supplies have been applied, then three
dummy cycles must be initiated. The first dummy cycle must
hold CS low until after the tenth SCLK edge, as shown in
Figure 19; the second and third dummy cycle place the part in
full power-down, as shown in Figure 22. (See the Operating
Modes section.) Once supplies are applied to the AD7475,
enough time must be allowed for the external reference to
power up and charge the reference capacitor to its final value.
For the AD7495, enough time should be allowed for the
internal reference buffer to charge the reference capacitor. Then,
to place the AD7475/ AD7495 in normal mode, a dummy cycle,
1 μs, should be initiated. If the first valid conversion is then
performed directly after the dummy conversion, ensure that
adequate acquisition time has been allowed. As mentioned
earlier, when powering up from the power-down mode, the part
returns to track upon the first SCLK edge applied after the
falling edge of CS. However, when the ADC powers up initially
after supplies are applied, the track-and-hold is already in track.
This means (assuming one has the facility to monitor the ADC
supply current) if the ADC powers up in the desired mode of
operation, and a dummy cycle is not required to change mode,
then neither is a dummy cycle required to place the track-andhold into track. If no current monitoring facility is available, the
relevant dummy cycle(s) should be performed to ensure the
part is in the required mode.
THE PART IS FULLY
POWERED UP
t POWER-UP
CS
1
10
16
16
1
SDATA
INVALID DATA
VALID DATA
Figure 23. Exiting Full Power-Down Mode
Rev. B | Page 18 of 24
01684-B-022
SCLK
AD7475/AD7495
POWER VS. THROUGHPUT RATE
By using the partial power-down mode on the AD7475/
AD7495 when not converting, the average power consumption
of the ADC decreases at lower throughput rates. Figure 24
shows how, as the throughput rate is reduced, the part remains
in its partial power-down state longer and the average power
consumption over time drops accordingly.
100
AD7495 5V
SCLK = 20MHz
AD7475 3V
SCLK = 20MHz
AD7495 3V
SCLK = 20MHz
0.1
0.001
0
50
100
150
200
250
THROUGHPUT (kSPS)
300
350
01684-B-025
0.01
Figure 24. Power vs. Throughput for Partial Power Down
For example, if the AD7495 is operated in a continuous
sampling mode with a throughput rate of 100 kSPS and an
SCLK of 20 MHz (VDD = 5 V), and the device is placed in partial
power-down mode between conversions, then the power
consumption is calculated as follows. The maximum power
dissipation during normal operation is 13 mW (VDD = 5 V). If
the power-up time from partial power-down is one dummy
cycle, that is, 1 μs, and the remaining conversion time is another
cycle, that is, 1 μs, then the AD7495 can be said to dissipate
13 mW for 2 μs during each conversion cycle. For the
remainder of the conversion cycle, 8 μs, the part remains in
partial power-down mode. The AD7495 dissipates 1.15 mW for
the remaining 8 μs of the conversion cycle. If the throughput
rate is 100 kSPS, and the cycle time is 10 μs, the average power
dissipated during each cycle is (2/10) × (13 mW) + (8/10) ×
(1.15 mW) = 3.52 mW. If VDD = 3 V, SCLK = 20 MHz and the
device is again in partial power-down mode between conversions, the power dissipated during normal operation is 6 mW.
Figure 25 shows a typical graph of current vs. throughput for
the AD7495 while operating in different modes. At slower
throughput rates, for example, 10 SPS to 1 kSPS, the AD7495
was operated in full power-down mode. As the throughput rate
increased, up to 100 kSPS, the AD7495 was operated in partial
power-down mode, with the part being powered down between
conversions. With throughput rates from 100 kSPS to 1 MSPS,
the part operated in normal mode, remaining fully powered up
at all times.
2.0
VDD = 5V
1.8
1.6
1.4
1.2
1.0
0.8
FULL
POWER-DOWN
PARTIAL
POWER-DOWN
NORMAL
0.6
0.4
0.2
0
10
100
1k
10k
THROUGHPUT (SPS)
100k
Figure 25. Typical AD7495 Current vs. Throughput
Rev. B | Page 19 of 24
1M
01684-B-026
1
Full power-down mode is intended for use in applications with
slower throughput rates than required for partial power-down
mode. It is necessary to leave 650 μs for the AD7495 to be fully
powered up from full power-down before initiating a conversion. Current consumptions between conversions is typically
less than 1 μA.
CURRENT (mA)
POWER (mW)
AD7475 5V
10 SCLK = 20MHz
The AD7495 dissipates 6 mW for 2 μs during each conversion
cycle and 0.69 mW for the remaining 8 μs where the part is in
partial power-down. With a throughput rate of 100 kSPS, the
average power dissipated during each conversion cycle is (2/10)
× (6 mW) + (8/10) × (0.69 mW) = 1.752 mW. Figure 24 shows
the power vs. throughput rate when using partial power-down
mode between conversions with both 5 V and 3 V supplies for
both the AD7475 and AD7495. For the AD7475, partial powerdown current is lower than that of the AD7495.
AD7475/AD7495
SERIAL INTERFACE
Sixteen serial clock cycles are required to perform the conversion process and to access data from the AD7475/AD7495.
CS going low provides the first leading zero to be read in by the
microcontroller or DSP. The remaining data is then clocked out
by subsequent SCLK falling edges beginning with the second
leading zero; thus the first falling clock edge on the serial clock
has the second leading zero provided. The final bit in the data
transfer is valid on the 16th falling edge, having been clocked out
on the previous (15th) falling edge.
Figure 26 shows the detailed timing diagram for serial interfacing to the AD7475/AD7495. The serial clock provides the
conversion clock and also controls the transfer of information
from the AD7475/AD7495 during conversion.
CS initiates the data transfer and conversion process. The falling
edge of CS puts the track-and-hold into hold mode and takes
the bus out of three-state. The analog input is sampled at this
point.
The conversion is also initiated at this point and requires
16 SCLK cycles to complete. Once 13 SCLK falling edges have
elapsed, the track-and-hold goes back into track on the next
SCLK rising edge, as shown in Figure 26 at Point B. On the 16th
SCLK falling edge, the SDATA line goes back into three-state.
If the rising edge of CS occurs before 16 SCLKs have elapsed,
the conversion is terminated and the SDATA line goes back
into three-state, as shown in Figure 27; otherwise SDATA
returns to three-state on the 16th SCLK falling edge, as shown
in Figure 26.
In applications with a slower SCLK, it may be possible to read in
data on each SCLK rising edge, although the first leading zero
still has to be read on the first SCLK falling edge after the CS
falling edge. Therefore, the first rising edge of SCLK after the
CS falling edge provides the second leading zero and the 15th
rising SCLK edge has DB0 provided. This method may not
work with most microprocessors/DSPs, but could possibly be
used with FPGAs and ASICs.
CS
tCONVERT
t6
SCLK
4
3
2
1
B
5
13
t5
t7
t8
t4
t3
0
SDATA
THREE-STATE
0
0
0
DB11
DB10
DB2
16
15
14
tQUIET
DB0
DB1
THREE-STATE
FOUR LEADING ZEROS
01684-B-027
t2
Figure 26. Serial Interface Timing Diagram
CS
tCONVERT
t6
4
3
2
1
B
5
13
15
16
tQUIET
t4
t3
0
SDATA
THREE-STATE
14
t9
t7
0
0
0
DB11
DB10
DB2
THREE-STATE
FOUR LEADING ZEROS
Figure 27. Serial Interface Timing Diagram — Conversion Termination
Rev. B | Page 20 of 24
01684-B-028
t2
SCLK
AD7475/AD7495
MICROPROCESSOR INTERFACING
AD7475/AD7495 TO TMS320C5X/C54X
The serial interface on the TMS320C5x/C54x uses a continuous
serial clock and frame synchronization signals to synchronize
the data transfer operations with peripheral devices like the
AD7475/AD7495. The CS input allows easy interfacing
between the TMS320C5x/C54x and the AD7475/AD7495
without any glue logic required. The serial port of the
TMS320C5x/C54x is set up to operate in burst mode with
internal CLKX (Tx serial clock) and FSX (Tx frame sync).
The serial port control register (SPC) must have the following
setup: FO = 0, FSM = 1, MCM = 1, and TXM = 1. The format
bit, FO, may be set to 1 to set the word length to 8 bits, in order
to implement the power-down modes on the AD7475/AD7495.
The connection diagram is shown in Figure 28. Note that for
signal processing applications, it is imperative that the frame
synchronization signal from the TMS320C5x/C54x provide
equidistant sampling. The VDRIVE pin of the AD7475/AD7495
takes the same supply voltage as that of the TMS320C5x/C54x.
This allows the ADC to operate at a higher voltage than the
serial interface, that is, TMS320C5x/C54x, if necessary.
AD7475/AD7495*
SCLK
TMS320C5x/C54x*
CLKX
CLKR
CS
VDRIVE
*ADDITIONAL PINS OMITTED FOR CLARITY
DR
FBX
FSR
VDD
01684-B-029
SDATA
AD7475/AD7495 TO ADSP-21XX
The ADSP-21xx family of DSPs is interfaced directly to the
AD7475/AD7495 without any glue logic required. The VDRIVE
pin of the AD7475/AD7495 takes the same supply voltage as
that of the ADSP-21xx. This allows the ADC to operate at a
higher voltage than the serial interface, that is, ADSP-21xx, if
necessary.
The SPORT control register should be set up as shown in Table 6.
Table 6.
SPORT Control Register Bits
TFSW = RFSW = 1
INVRFS = INVTFS = 1
DTYPE = 00
SLEN = 1111
ISCLK = 1
TFSR = RFSR = 1
IRFS = 0
ITFS = 1
Function
Alternate framing
Active low frame signal
Right-justify data
16-bit data words
Internal serial clock
Frame every word
To implement the power-down modes, SLEN should be set to
1001 to issue an 8-bit SCLK burst.
The connection diagram is shown in Figure 29. The ADSP-21xx
has the TFS and RFS of the SPORT tied together, with TFS set
as an output and RFS set as an input. The DSP operates in
alternate framing mode and the SPORT control register is set
up as described. The frame synchronization signal generated
on the TFS is tied to CS and, as with all signal processing
applications, equidistant sampling is necessary. However, in this
example, the timer interrupt is used to control the sampling rate
of the ADC and, under certain conditions, equidistant sampling
may not be achieved.
ADSP-21xx*
AD7475/AD7495*
SCLK
Figure 28. Interfacing to the TMS320C5x/54x
SDATA
SCLK
DR
CS
RFS
VDRIVE
TFS
*ADDITIONAL PINS OMITTED FOR CLARITY
VDD
Figure 29. Interfacing to the ADSP-21xx
Rev. B | Page 21 of 24
01684-B-030
The serial interface on the AD7475/AD7495 allows the parts
to be directly connected to a range of many different microprocessors. This section explains how to interface the AD7475/
AD7495 with some of the more common microcontroller and
DSP serial interface protocols.
AD7475/AD7495
For example, the ADSP-2111 has a master clock frequency of
16 MHz. If the SCLKDIV register is loaded with the value 3, an
SCLK of 2 MHz is obtained, and eight master clock periods
elapse for every one SCLK period. If the timer registers are
loaded with the value 803, 100.5 SCLKs occur between
interrupts and subsequently between transmit instructions.
This situation results in nonequidistant sampling because the
transmit instruction is occurring on a SCLK edge. If the
number of SCLKs between interrupts is a whole integer figure
of N, equidistant sampling is implemented by the DSP.
AD7475/AD7495 TO MC68HC16
The serial peripheral interface (SPI) on the MC68HC16 is
configured for master mode (MSTR) = 1, clock polarity bit
(CPOL) = 1, and the clock phase bit (CPHA) = 0. The SPI is
configured by writing to the SPI control register (SPCR), as
described in the 68HC16 User Manual. The serial transfer takes
place as a 16-bit operation when the size bit in the SPCR
register is set to size = 1. To implement the power-down modes
with an 8-bit transfer, set size = 0. (A connection diagram is
shown in Figure 31.) The VDRIVE pin of the AD7475/AD7495
takes the same supply voltage as that of the MC68HC16. This
allows the ADC to operate at a higher voltage than the serial
interface, that is, the MC68HC16, if necessary.
AD7475/AD7495*
SDATA
MISO/PMC0
SS/PMC3
VDRIVE
*ADDITIONAL PINS OMITTED FOR CLARITY
VDD
Figure 31. Interfacing to the MC68HC16
The connection diagram in Figure 30 shows how the AD7475/
AD7495 can be connected to the synchronous serial interface
(SSI) of the DSP56xxx family of devices from Motorola. The SSI
is operated in synchronous mode (SYN bit in CRB = 1) with
internally generated 1-bit clock period frame sync for both Tx
and Rx (Bits FSL1 = 1 and FSL0 = 0 in CRB). Set the word
length to 16 by setting Bits WL1 = 1 and WL0 = 0 in CRA. To
implement the power-down modes on the AD7475/AD7495,
the word length can be changed to 8 bits by setting Bit WL1 = 0
and Bit WL0 = 0 in CRA. For signal processing applications, it
is imperative that the frame synchronization signal from the
DSP56xxx provide equidistant sampling. The VDRIVE pin of the
AD7475/AD7495 takes the same supply voltage as that of the
DSP56xxx. This allows the ADC to operate at a voltage higher
than the serial interface, that is, DSP56xxx, if necessary.
AD7475/AD7495*
DSP56xxx*
SCLK
SDATA
SRD
CS
SC2
VDD
01684-B-031
VDRIVE
*ADDITIONAL PINS OMITTED FOR CLARITY
SCLK/PCM2
CS
AD7475/AD7495 TO DSP56XXX
SCLK
MC68HC16*
SCLK
Figure 30. Interfacing to the DSP56xxx
Rev. B | Page 22 of 24
01684-B-032
The timer registers are loaded with a value that provides an
interrupt at the required sample interval. When an interrupt is
received, a value is transmitted with TFS/DT (ADC control
word). The TFS is used to control the RFS, and therefore, the
reading of data. The frequency of the serial clock is set in the
SCLKDIV register. When the instruction to transmit with TFS
is given, (that is, AX0 = TX0), the state of the SCLK is checked.
The DSP waits until the SCLK has gone high, low, and high
before transmission starts. If the timer and SCLK values are
chosen such that the instruction to transmit occurs on or near
the rising edge of SCLK, the data can be transmitted or it can
wait until the next clock edge.
AD7475/AD7495
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
5
4.00 (0.1574)
3.80 (0.1497) 1
6.20 (0.2440)
4 5.80 (0.2284)
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
0.50 (0.0196)
× 45°
0.25 (0.0099)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 32. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
3.00
BSC
8
3.00
BSC
1
5
4.90
BSC
4
PIN 1
0.65 BSC
1.10 MAX
0.15
0.00
0.38
0.22
COPLANARITY
0.10
0.23
0.08
8°
0°
0.80
0.60
0.40
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 33. 8-Lead Mini Small Outline Package [MINI_SO]
(RM-8)
Dimensions shown in millimeters
Rev. B | Page 23 of 24
AD7475/AD7495
ORDERING GUIDE
Model
AD7475AR
AD7475AR-REEL
AD7475AR-REEL7
AD7475BR
AD7475BR-REEL
AD7475BR-REEL7
AD7475ARM
AD7475ARM-REEL
AD7475ARM-REEL7
AD7475BRM
AD7475BRM-REEL
AD7475BRM-REEL7
AD7475BRMZ3
AD7475BRMZ-REEL3
AD7475BRMZ-REEL73
AD7495AR
AD7495AR-REEL
AD7495AR-REEL7
AD7495BR
AD7495BR-REEL
AD7495BR-REEL7
AD7495BRZ 3
AD7495BRZ-REEL3
AD7495BRZ-REEL73
AD7495ARM
AD7495ARM-REEL
AD7495ARM-REEL7
AD7495ARMZ3
AD7495ARMZ-REEL3
AD7495ARMZ-REEL73
AD7495BRM
AD7495BRM-REEL
AD7495BRM-REEL7
EVAL-AD7495CB 4
EVAL-AD7475CB
EVAL-CONTROL BRD2 5
Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Linearity Error (LSB) 1
±1.5
±1.5
±1.5
±1
±1
±1
±1.5
±1.5
±1.5
±1
±1
±1
±1
±1
±1
±1.5
±1.5
±1.5
±1
±1
±1
±1
±1
±1
±1.5
±1.5
±1.5
±1.5
±1.5
±1.5
±1
±1
±1
1
Package Option 2
SO-8
SO-8
SO-8
SO-8
SO-8
SO-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
SO-8
SO-8
SO-8
SO-8
SO-8
SO-8
SO-8
SO-8
SO-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
Branding Information
C9A
C9A
C9A
C9B
C9B
C9B
C3C
C3C
C3C
CCA
CCA
CCA
C3B
C3B
C3B
CCB
CCB
CCB
Evaluation Board
Evaluation Board
Controller Board
Linearity error here refers to integral linearity error.
SO = SOIC; RM = MSOP.
3
Z = Pb-free part.
4
This can be used as a standalone evaluation board or in conjunction with the evaluation controller board for evaluation/demonstration purposes.
5
The evaluation board controller is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
2
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01684–0–5/05(B)
Rev. B | Page 24 of 24