Toshiba Matsushita Display Technology Co., Ltd. 22.6cm COLOUR TFT-LCD MODULE (8.9 TYPE) LTD089EXWS (p-Si TFT) PRODUCT INFORMATION FEATURES (1) (2) (3) (4) (5) 8.9”WIDE-XGA(1280x768 pixels) display size for notebook PC LED Backlight (7pcs. LEDs serial connection and 6 parallel circuits) Transflective Type Glare Surface Treatment Wedge Shape TENTATIVE Transflective Type MECHANICAL SPECIFICATIONS Item Dimensional Outline (typ.) Number of Pixels Active Area Pixel Pitch Weight (approximately) Backlight Specifications 224.0(W) x 133 (H) x 3.5/5.15 max(D) mm *) 1280 (W) x 768(H) pixels 193.920(W) x 116.352(H) mm 0.1515(W) x 0.1515(H) mm 130 g LED *) Exclude mounting hole ABSOLUTE MAXIMUM RATINGS Item Supply Voltage Min. -0.3 0 -0.3 0 -20 10 (VDD) (VLED) LED Currency (ILED) Input Signal Voltage (VIN) Operating Temperature Storage Temperature Storage Humidity Max. 4.0 5.0 30 VDD+0.3 50 60 90 Unit V V mA V °C °C %(RH) ELECTRICAL SPECIFICATION Item Supply Voltage Supply LED Voltage Common Mode Input Voltage Differential Input Amplitude Current Consumption (VDD) (VLED) (VCM) (VID) *1 (IDD) *2 (ILED) Power Consumption Min. 3.0 18.5 0.9 250 ------- Typ. 3.3 22.4 1.20 --280 15 2.94 Max. 3.6 25.7 1.75 450 20 --- Unit V V V mV mA mA W Remarks @1 parallel ILED=15 mA *1 : 8 color bars pattern *2 : The current value of each row should be the same value. *3 : The LED drive recommends to use the PWM drive. OPTICAL SPECIFICATION (Ta=25°C) Item Contrast Ratio (CR) Response Time (tON) (tOFF) Luminance (L) Reflectance (%) Viewing Angle Top/Bottom CR>10 Left/Right Min. 80 ----150 ------- Typ. 140 ----225 7.0 20/30 25/25 Max. --50 50 --------- Unit --ms cd/m2 % ° ° Remarks ILED=15mA B/L OFF *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba Matsushita Display technology or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba Matsushita Display technology or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display technology before proceeding with the design of equipment incorporating this product. (1/10) 2007-03-20 (Ver.0.3) LTD089EXWS DIMENSIONAL OUTLINE (Front side) TENTATIVE Unit : mm Standard tolerance : ±0.5 (2/10) 2007-03-20 (Ver.0.3) LTD089EXWS DIMENSIONAL OUTLINE (Back side) TENTATIVE Note 1) Never push LCD back side. If LCD back side was pressed, It may cause damage of the back light system. (3/10) 2007-03-20 (Ver.0.3) LTD089EXWS BLOCK DIAGRAM Gray scale Manipulation Voltage Generation Circuit Liquid Cr ystal Panel 128 0 x 768 pix els Y-driv er Y-driv er DC/DC converte r Connect or CN1 P anel Cont roller L VD S in c lu d e X-dr iver LED 1280 pixels 1, 1 1, 2 1, Y 2, 1 X2n-1, 1 X2n, 1 X2n-1, Y X2n, Y 1, 768 1280, 1 768 pixels 1280,768 (4/10) 2007-03-20 (Ver.0.3) LTD089EXWS TIMING CHART tv tvw VSYNC tvsu tvhd th HSYNC tvｆp tvbp tvd tvds DE 767 1 768 2 th thw HSYNC thbp thfp thds thd DE 1280 pixel 1 2 3 4 CLK (5/10) 2007-03-20 (Ver.0.3) LTD089EXWS TIMING SPECIFICATION 1) 2) 3) 4) 5) 6) Item Horizontal Scanning Term H-sync Pulse Width Horizontal Front Porch Horizontal Back Porch Horizontal Data Sync Period Horizontal Display Term Frame Period V-sync Pulse Width V-sync Set Up Time (to H-sync) V-sync Hold Time Vertical Front Porch Vertical Back Porch Vertical Data Sync Period Vertical Display Term Clock Period Symbol th thw thfp thbp thds thd tv tvw tvsu tvhd tvfp tvbp tvds tvd tc min. 1560 x tc 4 x tc 8 x tc 8 x tc 12 x tc 1280 x tc 771 x th 1 x th 4 x tc 4 x tc 1 x th 1 x th 2 x th 768 x th 12.20 (82.0MHz) typ. 1664 x tc 128 x tc 64 x tc 192 x tc 320 x tc 1280 x tc 798 x th 7 x th 3 x th 20 x th 27 x th 768 x th 12.58 (79.5MHz) max. 1712 x tc 1280 x tc 825 x th 768 x th 13.33 (75.0MHz) unit clock clock clock clock clock clock line line clock clock line line line line ns Note 1) Refer to “Timing Chart” and LVDS specifications in TIA/EIA-644. Note 2) If DE is fixed to "H" or "L" level for certain period while NCLK is supplied, the panel displays black with some flicker. Note 3) If NCLK is fixed to "H" or "L" level for certain period while DE is supplied, the panel may be damaged. Note4) tvb = tvw + tvfp + tvbp thb = thw + thfp + thbp Note5) In case of using the long frame period, the deterioration of display quality, noise etc. may be occurred. Note6) NCLK count of each Horizontal Scanning Time should be always the same. V-Blanking period should be “n” X “Horizontal Scanning Time”. (n: integer) Frame period should be always the same. (6/10) 2007-03-20 (Ver.0.3) LTD089EXWS CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector : 20347-030E-02/I-PEX Mating Connector : 20345-*30T-##/I-PEX Terminal No. Symbol Function Power Supply : +3.3V 1 VDD Power Supply : +3.3V 2 VDD Power Supply : +3.3V 3 VDD Power Supply : +3.3V 4 VDD 5 NC Non-Connection GND 6 VSS GND 7 VSS GND 8 VSS GND 9 VSS 10 RxIN0Negative LVDS differential data input (R0-R5,G0) 11 RxIN0+ Positive LVDS differential data input (R0-R5,G0) GND 12 VSS 13 RxIN1Negative LVDS differential data input (G1-G5, B0-B1) 14 RxIN1+ Positive LVDS differential data input (G1-G5, B0-B1) GND 15 VSS 16 RxIN2Negative LVDS differential data input (B2-B5, HSYNC, VSYNC, DE) 17 RxIN2+ Positive LVDS differential data input (B2-B5, HSYNC, VSYNC, DE) GND 18 VSS 19 RxCLKINClock Signal(-) 20 RxCLKIN+ Clock Signal(+) GND 21 VSS 22 NC Non-Connection 23 VCD1 LED Cathode (Negative) 24 VCD2 LED Cathode (Negative) 25 VCD3 LED Cathode (Negative) 26 VCD4 LED Cathode (Negative) 27 VCD5 LED Cathode (Negative) 28 VCD6 LED Cathode (Negative) 29 NC Non-Connection 30 VAD LED Anode (Positive) Note 1) Please connect GND pin to ground. Don't use it as no-connect nor connection with high impedance. Note 2) Please connect NC to nothing. Don't connect it to ground nor to other signal input. R x IN 0 T IN6 G0 R x IN 1 T IN13 B1 R x IN 2 T IN20 DE T IN5 T IN4 T IN3 T IN2 T IN1 T IN0 R5 R4 R3 R2 R1 R0 T IN12 T IN11 T IN10 T IN9 T IN8 T IN7 B0 G5 G4 G3 G2 G1 T IN19 T IN18 T IN17 T IN16 T IN15 VSYNC HSYNC B5 (7/10) B4 B3 T IN14 B2 2007-03-20 (Ver.0.3) LTD089EXWS EQUIVALENT CIRCUIT OF LED Terminal No.28 No.27 No.26 No.25 No.24 No.23 Connector (CN1) I LED I LED I LED I LED I LED I LED 7 LEDs Terminal No.30 (8/10) 2007-03-20 (Ver.0.3) LTD089EXWS 256k (k=1024) COLORS COMBINATION TABLE Display Basic Color Gray Scale of Red Black Blue Green Light Blue Red Purple Yellow White Black Dark ↑ ↓ Light Red Black Gray Scale of Green Dark ↑ ↓ Light Green Black Gray Scale of Blue Dark ↑ ↓ Light Blue Black Gray Scale of White & Black Dark ↑ ↓ Light White R5 R4 R3 R2 R1 R0 L L L L H H H H L L L L L L L H H H H L L L L L L L H H H H L L L L L L L H H H H L L L L L L L H H H H L L H L L L L H H H H L H L G5 G4 G3 G2 G1 G0 L L H H L L H H L L L L L H H L L H H L L L L L H H L L H H L L L : : H H H L L L H H H L L L H H H L L L L L L L L L H H H L L L L L L L L L L H H L L L H L H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H H H L L L H H H L L L H H H H H H L H L H L H L H L L L L H L H L H L H L L L L H L H L H L H L L L L L L L L H L L L L H L L L L L L L L L L L L L L L L L L L L H H L L L H L H L L L L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L H L L L L H L L L L L L L L L L L L L L L L L L L L H H H L H H H H H H H H H H L H L H L H L H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H L L L L H L L61 L62 Green L63 L 0 L 1 L 2 L3… L60 H H H L L L L H H L L H H L H L H L L61 L62 Blue L63 L 0 L 1 L 2 L3… L60 H H H L H H H L H L61 L62 White L63 : : L L L L L L L L L L L H L L L L H L H H H L L L H H H L L L H H H L L L : : H H H L H L H L H L H L L L : : H H H L L L : : H H H (9/10) L H H H L H H H H H H H H H H Gray Scale Level L 0 L 1 L 2 L3… L60 L H L H L H L H L L L : : L L L L L L H H H L L L : : H H H L L H H L L H H L L L : : : : L L L L L L L L H H L L H H L L L : : : : L L L L L L L L H H L L H H L L L B5 B4 B3 B2 B1 B0 L61 L62 Red L63 L 0 L 1 L 2 L3… L60 2007-03-20 (Ver.0.3) LTD089EXWS ! FOR SAFETY LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-D-001A,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA MATSUSHITA DISPLAY TECHNOLOGY CO., LTD LCD MODULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information. 1) SPECIAL PURPOSES A) Toshiba Matsushita Display technology's Standard LCD Modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic. B) Since Toshiba Matsushita Display technology's Standard LCD Modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba Matsushita Display technology's published specification limits. C) In addition, since Toshiba Matsushita Display technology Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) DISASSEMBLING OR MODIFICATION DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. Toshiba Matsushita Display technology doses not warrant the module, if customer disassembled or modified it. 3) BREAKAGE OF LCD PANEL DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is broken and liquid crystal material spills out. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) GLASS OF LCD PANEL BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken. 5) ELECTRIC SHOCK DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module and the connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from power supply is turned on. 6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged. Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design. 7) DISPOSAL When dispose LCD module, obey to the applicable environmental regulations. (10/10) 2007-03-20 (Ver.0.3)