1N5807US thru 1N5811US SURFACE MOUNT VOIDLESSHERMETICALLY-SEALED ULTRA FAST RECOVERY GLASS RECTIFIERS SCOTTSDALE DIVISION APPEARANCE This “Ultrafast Recovery” surface mount rectifier diode series is military qualified to MIL-PRF-19500/477 and is ideal for high-reliability applications where a failure cannot be tolerated. These industry-recognized 6.0 Amp rated rectifiers for working peak reverse voltages from 50 to 150 volts are hermetically sealed with voidlessglass construction using an internal “Category I” metallurgical bond. These devices are also available in axial-leaded package configurations (see separate data sheet for 1N5807 thru 1N5811). Microsemi also offers numerous other rectifier products to meet higher and lower current ratings with various recovery time speed requirements including standard, fast, and ultrafast device types in both throughhole and surface mount packages. WWW . Microsemi .C OM DESCRIPTION Package “E” or D-5B IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com FEATURES • • • • • • • APPLICATIONS / BENEFITS • • • Surface mount package series equivalent to the JEDEC registered 1N5807 to 1N5811 series Voidless-hermetically-sealed glass package Extremely robust construction Triple-layer passivation Internal “Category I” Metallurgical bonds JAN, JANTX, JANTXV, and JANS available per MILPRF-19500/477 Axial-leaded equivalents also available (see separate data sheet for 1N5807 thru 1N5811) • • • • Ultrafast recovery 6 Amp rectifiers series 50 to 150 V Military and other high-reliability applications Switching power supplies or other applications requiring extremely fast switching & low forward loss High forward surge current capability Low thermal resistance Controlled avalanche with peak reverse power capability Inherently radiation hard as described in Microsemi MicroNote 050 MAXIMUM RATINGS • • • • • • • o MECHANICAL AND PACKAGING o • Operating Temperature: -65 C to +175 C. Storage Temperature: -65oC to +175oC. Average Rectified Forward Current (IO): 6 Amps @ TEC = 75ºC End Cap temperature (see note 1) Thermal Resistance: 10 ºC/W junction to end cap Thermal Impedance: 1.5 ºC/W @ 10 ms heating time Forward Surge Current (8.3 ms half sine) 125 Amps Solder temperature: 260ºC for 10 s (maximum) • • • • • CASE: Hermetically sealed voidless hard glass with Tungsten slugs TERMINALS: End caps are solid Silver with Tin/Lead (Sn/Pb) finish MARKING & POLARITY: Cathode band only Tape & Reel option: Standard per EIA-481-B Weight: 539 mg See package dimensions and recommended pad layout on last page ELECTRICAL CHARACTERISTICS BREAKDOWN VOLTAGE (MIN.) @ 100µA VBR VOLTS VOLTS AVERAGE RECTIFIED CURRENT IO1 @TEC=75ºC (Note 1) AMPS AVERAGE RECTIFIED CURRENT IO2 @TA=55ºC (Note 2) AMPS MAXIMUM FORWARD VOLTAGE @4A (8.3 ms pulse) VF 1N5807US 50 60 6.0 3.0 VOLTS o o 25 C 100 C 0.875 0.800 1N5809US 100 110 6.0 3.0 0.875 0.800 REVERSE CURRENT (MAX) @ VRWM IR o 25 C 5 5 µA o 100 C 150 150 SURGE CURRENT (MAX) IFSM (NOTE 3) REVERSE RECOVERY TIME (MAX) (NOTE 4) trr AMPS ns 125 30 125 30 1N5811US 150 160 6.0 3.0 0.875 0.800 5 150 125 30 NOTE 1: Rated at TEC = 75ºC. Derate at 60 mA/ºC for TEC above 75ºC NOTE 2: Derate linearly at 25 mA/ºC above TA = 55ºC. This rating is typical for PC boards where thermal resistance from mounting point to ambient is sufficiently controlled where TJ(max) does not exceed 175ºC o NOTE 3: TA = 25 C @ IO = 3.0 A and VRWM for ten 8.3 ms surges at 1 minute intervals NOTE 4: IF = 1.0 A, IRM = 1.0 A, IR(REC) = 0.10 A and di/dt = 100 A/µs min Copyright 2004 1-14-2005 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 1 1N5807US–1N5811US TYPE WORKING PEAK REVERSE VOLTAGE VRWM 1N5807US thru 1N5811US SCOTTSDALE DIVISION VRWM VF IR C trr Minimum Breakdown Voltage: The minimum voltage the device will exhibit at a specified current. Working Peak Reverse Voltage: The maximum peak voltage that can be applied over the operating temperature range. Maximum Forward Voltage: The maximum forward voltage the device will exhibit at a specified current. Maximum Leakage Current: The maximum leakage current that will flow at the specified voltage and temperature. Capacitance: The capacitance in pF at a frequency of 1 MHz and specified voltage Reverse Recovery Time: The time interval between the instant the current passes through zero when changing from the forward direction to the reverse direction and a specified recovery decay point after a peak reverse current is reached. WWW . Microsemi .C OM SYMBOLS & DEFINITIONS Definition Symbol VBR SURFACE MOUNT VOIDLESSHERMETICALLY-SEALED ULTRA FAST RECOVERY GLASS RECTIFIERS GRAPHS FIGURE 1 TYPICAL FORWARD CURRENT vs. FORWARD VOLTAGE FIGURE 2 TYPICAL REVERSE CURRENT vs. VOLTAGE 1N5807US–1N5811US FIGURE 3 FORWARD PULSE CURRENT vs. DURATION Copyright 2004 1-14-2005 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 2 1N5807US thru 1N5811US SCOTTSDALE DIVISION SURFACE MOUNT VOIDLESSHERMETICALLY-SEALED ULTRA FAST RECOVERY GLASS RECTIFIERS WWW . Microsemi .C OM FIGURE 4 MULTIPLE SURGE CURRENT vs. DURATION PACKAGE DIMENSIONS AND PAD LAYOUT NOTE: This Package Outline has also previously been identified as “D-5B” INCHES BL mm mm MIN MAX MIN MAX A 0.288 7.32 .205 .225 5.21 5.72 B 0.070 1.78 3.61 C 0.155 3.94 .137 .142 3.48 ECT .019 .028 0.48 0.711 S .003 --- 0.08 --- Copyright 2004 1-14-2005 REV B INCHES 1N5807US–1N5811US BD PAD LAYOUT Note: If mounting requires adhesive separate from the solder, an additional 0.080 inch diameter contact may be placed in the center between the pads as an optional spot for cement. Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 3