ONSEMI 74VCXH16373DTR

74VCXH16373
Low−Voltage 1.8/2.5/3.3 V
16−Bit Transparent Latch
With 3.6 V−Tolerant Inputs and Outputs
(3−State, Non−Inverting)
The 74VCXH16373 is an advanced performance, non−inverting
16−bit transparent latch. It is designed for very high−speed, very
low−power operation in 1.8 V, 2.5 V or 3.3 V systems. The
VCXH16373 is byte controlled, with each byte functioning
identically, but independently. Each byte has separate Output Enable
and Latch Enable inputs. These control pins can be tied together for
full 16−bit operation.
When operating at 2.5 V (or 1.8 V) the part is designed to tolerate
voltages it may encounter on either inputs or outputs when interfacing
to 3.3 V busses. It is guaranteed to be overvoltage tolerant to 3.6 V.
The 74VCXH16373 contains 16 D−type latches with 3−state
3.6 V−tolerant outputs. When the Latch Enable (LEn) inputs are
HIGH, data on the Dn inputs enters the latches. In this condition, the
latches are transparent, (a latch output will change state each time its D
input changes). When LE is LOW, the latch stores the information that
was present on the D inputs a setup time preceding the
HIGH−to−LOW transition of LE. The 3−state outputs are controlled
by the Output Enable (OEn) inputs. When OE is LOW, the outputs are
enabled. When OE is HIGH, the standard outputs are in the high
impedance state, but this does not interfere with new data entering into
the latches. The data inputs include active bushold circuitry,
eliminating the need for external pullup resistors to hold unused or
floating inputs at a valid logic state.
http://onsemi.com
TSSOP−48
DT SUFFIX
CASE 1201
48
1
MARKING DIAGRAM
48
VCXH16373
AWLYYWW
1
A
WL
YY
WW
Features
PIN NAMES
• Designed for Low Voltage Operation: VCC = 1.65 V − 3.6 V
• 3.6 V Tolerant Inputs and Outputs
• High Speed Operation: 3.0 ns max for 3.0 V to 3.6 V
•
•
•
•
•
•
•
•
3.9 ns max for 2.3 V to 2.7 V
6.8 ns max for 1.65 V to 1.95 V
Static Drive: ±24 mA Drive at 3.0 V
±18 mA Drive at 2.3 V
±6 mA Drive at 1.65 V
Supports Live Insertion and Withdrawal
Includes Active Bushold to Hold Unused or Floating Inputs at
a Valid Logic State
IOFF Specification Guarantees High Impedance When VCC = 0 V*
Near Zero Static Supply Current in All Three Logic States (20 mA)
Substantially Reduces System Power Requirements
Latchup Performance Exceeds ±250 mA @ 125°C
ESD Performance: Human Body Model >2000 V
Machine Model >200 V
Pb−Free Package is Available**
*To ensure the outputs activate in the 3−state condition,
the output enable pins should be connected to VCC through a
pull−up resistor. The value of the resistor is determined by the
current sinking capability of the output connected to the OE pin.
© Semiconductor Components Industries, LLC, 2006
June, 2006 − Rev. 6
= Assembly Location
= Wafer Lot
= Year
= Work Week
1
Pins
Function
OEn
LEn
D0−D15
O0−O15
Output Enable Inputs
Latch Enable Inputs
Inputs
Outputs
ORDERING INFORMATION
Package
Shipping †
74VCXH16373DT
TSSOP
39 / Rail
74VCXH16373DTR
TSSOP
2500/Tape & Reel
Device
74VCXH16373DTRG TSSOP 2500/Tape & Reel
(Pb−Free)
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
**For additional information on our Pb−Free strategy
and soldering details, please download the
ON Semiconductor Soldering and Mounting
Techniques Reference Manual, SOLDERRM/D.
Publication Order Number:
74VCXH16373/D
74VCXH16373
OE1 1
48 LE1
O0 2
O1 3
47 D0
46 D1
GND 4
O2 5
45 GND
44 D2
O3 6
43 D3
VCC 7
O4 8
42 VCC
41 D4
O5 9
GND 10
40 D5
39 GND
O6 11
O7 12
38 D6
O8 13
36 D8
O9 14
GND 15
OE1
LE1
D0
D1
D2
37 D7
D3
35 D9
34 GND
O10 16
O11 17
33 D10
32 D11
VCC 18
31 VCC
O12 19
O13 20
30 D12
29 D13
GND 21
O14 22
28 GND
27 D14
O15 23
OE2 24
26 D15
25 LE2
D4
D5
D6
D7
1
OE2
48
LE2
nLE
47
D
nLE
46
D
nLE
44
D
nLE
43
D
nLE
41
D
nLE
40
D
nLE
38
D
nLE
37
D
2
Q
3
Q
5
Q
6
Q
8
Q
9
Q
11
Q
12
Q
Figure 1. 48−Lead Pinout
(Top View)
O0
D8
O1
D9
O2
D10
O3
D11
O4
D12
O5
D13
O6
D14
O7
D15
24
25
36
35
33
32
30
29
27
26
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
Figure 2. Logic Diagram
OE1 1
LE1 48
25
LE2
24
OE2
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
47
46
44
43
41
40
38
37
36
35
33
32
30
29
27
26
EN1
EN2
EN3
EN4
1
1∇
1
2∇
1
3∇
1
4∇
2
3
5
6
8
9
11
12
13
14
16
17
19
20
22
23
Figure 3. IEC Logic Diagram
http://onsemi.com
2
O0
O1
O2
O3
O4
O5
O6
O7
O8
O9
O10
O11
O12
O13
O14
O15
Q
Q
Q
Q
Q
Q
Q
Q
13
14
16
17
19
20
22
23
O8
O9
O10
O11
O12
O13
O14
O15
74VCXH16373
TRUTH TABLE
Inputs
Outputs
Inputs
Outputs
LE1
OE1
D0:7
O0:7
LE2
OE2
D8:15
O8:15
X
H
X
Z
X
H
X
Z
H
L
L
L
H
L
L
L
H
L
H
H
H
L
H
H
L
L
X
O0
L
L
X
O0
H = High Voltage Level
L = Low Voltage Level
Z = High Impedance State
X = High or Low Voltage Level and Transitions Are Acceptable, for ICC reasons, DO NOT FLOAT Inputs.
O0 = No Change.
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
VCC
DC Supply Voltage
VI
VO
Value
Condition
Unit
−0.5 to +4.6
V
DC Input Voltage
−0.5 ≤ VI ≤ +4.6
V
DC Output Voltage
−0.5 ≤ VO ≤ +4.6
Output in 3−State
V
−0.5 ≤ VO ≤ VCC + 0.5
Note 1; Outputs Active
V
−50
VI < GND
mA
−50
VO < GND
mA
+50
VO > VCC
mA
IIK
DC Input Diode Current
IOK
DC Output Diode Current
IO
DC Output Source/Sink Current
±50
mA
ICC
DC Supply Current Per Supply Pin
±100
mA
IGND
DC Ground Current Per Ground Pin
±100
mA
TSTG
Storage Temperature Range
−65 to +150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. IO absolute maximum rating must be observed.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Typ
Max
Unit
1.65
1.2
3.3
3.3
3.6
3.6
V
−0.3
3.6
V
0
0
VCC
3.6
V
HIGH Level Output Current, VCC = 3.0 V − 3.6 V
−24
mA
IOL
LOW Level Output Current, VCC = 3.0 V − 3.6 V
24
mA
IOH
HIGH Level Output Current, VCC = 2.3 V − 2.7 V
−18
mA
IOL
LOW Level Output Current, VCC = 2.3 V − 2.7 V
18
mA
IOH
HIGH Level Output Current, VCC = 1.65 V − 1.95 V
−6
mA
IOL
LOW Level Output Current, VCC = 1.65 V − 1.95 V
6
mA
TA
Operating Free−Air Temperature
−40
+85
°C
Dt/DV
Input Transition Rise or Fall Rate, VIN from 0.8 V to 2.0 V, VCC = 3.0 V
0
10
ns/V
VCC
Supply Voltage
VI
Input Voltage
VO
Output Voltage
IOH
Operating
Data Retention Only
(Active State)
(3−State)
http://onsemi.com
3
74VCXH16373
DC ELECTRICAL CHARACTERISTICS
TA = −40°C to +85°C
Symbol
VIH
VIL
VOH
VOL
II
Characteristic
HIGH Level Input Voltage (Note 2)
LOW Level Input Voltage (Note 2)
HIGH Level Output Voltage
LOW Level Output Voltage
Input Leakage Current
II(HOLD)
II (OD)
Minimum Bushold Input Current
Minimum Bushold Over−Drive
Current Needed to Change State
IOZ
3−State Output Current
IOFF
Power−Off Leakage Current
ICC
DICC
2.
3.
4.
5.
Quiescent Supply Current (Note 5)
Increase in ICC per Input
Condition
Min
1.65 V ≤ VCC < 2.3 V
0.65 x VCC
2.3 V ≤ VCC ≤ 2.7 V
1.6
2.7 V < VCC ≤ 3.6 V
2.0
Max
V
1.65 V ≤ VCC < 2.3 V
0.35 x VCC
2.3 V ≤ VCC ≤ 2.7 V
0.7
2.7 V < VCC ≤ 3.6 V
0.8
1.65 V ≤ VCC ≤ 3.6 V; IOH = −100 mA
VCC − 0.2
VCC = 1.65 V; IOH = −6 mA
1.25
VCC = 2.3 V; IOH = −6 mA
2.0
VCC = 2.3 V; IOH = −12 mA
1.8
VCC = 2.3 V; IOH = −18 mA
1.7
VCC = 2.7 V; IOH = −12 mA
2.2
VCC = 3.0 V; IOH = −18 mA
2.4
VCC = 3.0 V; IOH = −24 mA
2.2
0.2
VCC = 1.65 V; IOL = 6 mA
0.3
VCC = 2.3 V; IOL = 12 mA
0.4
VCC = 2.3 V; IOL = 18 mA
0.6
VCC = 2.7 V; IOL = 12 mA
0.4
VCC = 3.0 V; IOL = 18 mA
0.4
VCC = 3.0 V; IOL = 24 mA
0.55
±5.0
VCC = 3.0 V, VIN = 0.8 V
75
VCC = 3.0 V, VIN = 2.0 V
−75
VCC = 2.3 V, VIN = 0.7 V
45
VCC = 2.3 V, VIN = 1.6 V
−45
VCC = 1.65 V, VIN = 0.57 V
25
VCC = 1.65 V, VIN = 1.07 V
−25
VCC = 3.6 V, (Note 3)
450
VCC = 3.6 V, (Note 4)
−450
VCC = 2.7 V, (Note 3)
300
VCC = 2.7 V, (Note 4)
−300
VCC = 1.95 V, (Note 3)
200
VCC = 1.95 V, (Note 4)
−200
V
V
1.65 V ≤ VCC ≤ 3.6 V; IOL = 100 mA
1.65 V ≤ VCC ≤ 3.6 V; 0V ≤ VI ≤ 3.6 V
Unit
V
mA
mA
mA
1.65 V ≤ VCC ≤ 3.6 V; 0 V ≤ VO ≤ 3.6 V;
VI = VIH or VIL
±10
mA
VCC = 0 V; VI or VO = 3.6 V
10
mA
1.65 V ≤ VCC ≤ 3.6 V; VI = GND or VCC
20
mA
1.65 V ≤ VCC ≤ 3.6 V; 3.6 V ≤ VI, VO ≤ 3.6 V
±20
mA
2.7 V < VCC ≤ 3.6 V; VIH = VCC − 0.6 V
750
mA
These values of VI are used to test DC electrical characteristics only.
An external driver must source at least the specified current to switch from LOW−to−HIGH.
An external driver must source at least the specified current to switch from HIGH−to−LOW.
Outputs disabled or 3−state only.
http://onsemi.com
4
74VCXH16373
AC CHARACTERISTICS (Note 6; tR = tF = 2.0 ns; CL = 30 pF; RL = 500 W)
TA = −40°C to +85°C
VCC = 3.0 V to 3.6 V
Symbol
Parameter
VCC = 2.3 V to 2.7 V
VCC = 1.65 V to 1.95 V
Waveform
Min
Max
Min
Max
Min
Max
Unit
tPLH
tPHL
Propagation Delay
Dn−to−On
1
0.8
0.8
3.0
3.0
1.0
1.0
3.4
3.4
1.5
1.5
6.8
6.8
ns
tPLH
tPHL
Propagation Delay
LE−to−On
1
0.8
0.8
3.0
3.0
1.0
1.0
3.9
3.9
1.5
1.5
7.8
7.8
ns
tPZH
tPZL
Output Enable Time to
High and Low Level
2
0.8
0.8
3.5
3.5
1.0
1.0
4.6
4.6
1.5
1.5
9.2
9.2
ns
tPHZ
tPLZ
Output Disable Time From
High and Low Level
2
0.8
0.8
3.5
3.5
1.0
1.0
3.8
3.8
1.5
1.5
6.8
6.8
ns
ts
Setup Time, High or Low
Dn−to−LE
3
1.5
1.5
2.5
ns
th
Hold Time, High or Low
Dn−to−LE
3
1.0
1.0
1.0
ns
tw
LE Pulse Width, High
3
1.5
1.5
4.0
ns
tOSHL
tOSLH
Output−to−Output Skew
(Note 7)
0.5
0.5
0.5
0.5
0.75
0.75
ns
6. For CL = 50 pF, add approximately 300 ps to the AC maximum specification.
7. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH−to−LOW (tOSHL) or LOW−to−HIGH (tOSLH); parameter
guaranteed by design.
AC CHARACTERISTICS (tR = tF = 2.0 ns; CL = 50 pF; RL = 500 W)
TA = −40°C to +85°C
VCC = 3.0 V to 3.6 V
Symbol
Parameter
Waveform
Min
Max
VCC = 2.7 V
Min
Max
Unit
tPLH
tPHL
Propagation Delay
Dn−to−On
4
1.0
1.0
3.6
3.6
4.3
4.3
ns
tPLH
tPHL
Propagation Delay
LE−to−On
4
1.0
1.0
3.9
3.9
4.6
4.6
ns
tPZH
tPZL
Output Enable Time to
High and Low Level
5
1.0
1.0
4.7
4.7
5.7
5.7
ns
tPHZ
tPLZ
Output Disable Time From
High and Low Level
5
1.0
1.0
4.1
4.1
4.5
4.5
ns
tOSHL
tOSLH
Output−to−Output Skew
(Note 8)
0.5
0.5
0.5
0.5
ns
8. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH−to−LOW (tOSHL) or LOW−to−HIGH (tOSLH); parameter
guaranteed by design.
http://onsemi.com
5
74VCXH16373
DYNAMIC SWITCHING CHARACTERISTICS
TA = +25°C
Symbol
VOLP
VOLV
VOHV
Condition
Typ
Unit
VCC = 1.8 V, CL = 30 pF, VIH = VCC, VIL = 0 V
0.25
V
VCC = 2.5 V, CL = 30 pF, VIH = VCC, VIL = 0 V
0.6
VCC = 3.3 V, CL = 30 pF, VIH = VCC, VIL = 0 V
0.8
VCC = 1.8 V, CL = 30 pF, VIH = VCC, VIL = 0 V
−0.25
VCC = 2.5 V, CL = 30 pF, VIH = VCC, VIL = 0 V
−0.6
VCC = 3.3 V, CL = 30 pF, VIH = VCC, VIL = 0 V
−0.8
VCC = 1.8 V, CL = 30 pF, VIH = VCC, VIL = 0 V
1.5
VCC = 2.5 V, CL = 30 pF, VIH = VCC, VIL = 0 V
1.9
VCC = 3.3 V, CL = 30 pF, VIH = VCC, VIL = 0 V
2.2
Characteristic
Dynamic LOW Peak Voltage
(Note 9)
Dynamic LOW Valley Voltage
(Note 9)
Dynamic HIGH Valley Voltage
(Note 10)
V
V
9. Number of outputs defined as “n”. Measured with “n−1” outputs switching from HIGH−to−LOW or LOW−to−HIGH. The remaining output is
measured in the LOW state.
10. Number of outputs defined as “n”. Measured with “n−1” outputs switching from HIGH−to−LOW or LOW−to−HIGH. The remaining output is
measured in the HIGH state.
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
CIN
Input Capacitance
COUT
Output Capacitance
CPD
Power Dissipation Capacitance
Condition
Typical
Unit
Note 11
6
pF
Note 11
7
pF
Note 11, 10 MHz
20
pF
11. VCC = 1.8 V, 2.5 V or 3.3 V; VI = 0 V or VCC.
http://onsemi.com
6
74VCXH16373
VIH
Vm
Dn
Vm
0V
tPLH
tPHL
VOH
On
Vm
Vm
VOL
WAVEFORM 1 − PROPAGATION DELAYS
tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns
Figure 4. AC Waveforms
VIH
Vm
OEn
VIH
Dn
Vm
Vm
Vm
0V
tPZH
On
0V
ts
tPHZ
VIH
VOH
Vy
LEn
Vm
tw
Vm
tPLH, tPHL
tPLZ
≈ VCC
On
Vm
0V
≈ 0V
tPZL
th
VOH
On
Vm
Vm
VOL
Vx
VOL
WAVEFORM 3 − LE to On PROPAGATION DELAYS, LE MINIMUM
PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES
tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns except when noted
WAVEFORM 2 − OUTPUT ENABLE AND DISABLE TIMES
tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns
Figure 5. AC Waveforms
Table 1. AC WAVEFORMS
VCC
Symbol
3.3 V ± 0.3 V
2.5 V ± 0.2 V
1.8 V ± 0.15 V
VIH
2.7 V
VCC
VCC
Vm
1.5 V
VCC/2
VCC/2
Vx
VOL + 0.3 V
VOL + 0.15 V
VOL + 0.15 V
Vy
VOH − 0.3 V
VOH − 0.15 V
VOH − 0.15 V
http://onsemi.com
7
74VCXH16373
VCC
PULSE
GENERATOR
RL
DUT
RT
CL
RL
Figure 6. Test Circuit
Table 2. TEST CIRCUIT
TEST
SWITCH
tPLH, tPHL
Open
tPZL, tPLZ
6 V at VCC = 3.3 ± 0.3 V;
VCC × 2 at VCC = 2.5 ± 0.2 V; 1.8 ± 0.15 V
tPZH, tPHZ
GND
CL = 30 pF or equivalent (Includes jig and probe capacitance)
RL = 500 W or equivalent
RT = ZOUT of pulse generator (typically 50 W)
http://onsemi.com
8
6 V or VCC × 2
OPEN
GND
74VCXH16373
VIH
Vm
Dn
Vm
0V
tPLH
tPHL
VOH
On
Vm
Vm
VOL
WAVEFORM 4 − PROPAGATION DELAYS
tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns
Figure 7. AC Waveforms
VIH
Vm
OEn
VIH
Dn
Vm
Vm
Vm
0V
tPZH
On
0V
ts
tPHZ
VIH
VOH
Vy
LEn
Vm
tw
Vm
tPLH, tPHL
tPLZ
≈ VCC
On
Vm
0V
≈0V
tPZL
th
Vm
WAVEFORM 5 − OUTPUT ENABLE AND DISABLE TIMES
tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns
VOH
On
Vm
VOL
Vx
VOL
WAVEFORM 6 − LE to On PROPAGATION DELAYS, LE MINIMUM
PULSE WIDTH, Dn−to−LE SETUP AND HOLD TIMES
tR = tF = 2.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns except when noted
Figure 8. AC Waveforms
Table 3. AC WAVEFORMS
VCC
Symbol
3.3 V ± 0.3 V
2.7 V
VIH
2.7 V
2.7 V
Vm
1.5 V
1.5 V
Vx
VOL + 0.3 V
VOL + 0.3 V
Vy
VOH − 0.3 V
VOH − 0.3 V
http://onsemi.com
9
74VCXH16373
VCC
PULSE
GENERATOR
RL
DUT
RT
CL
RL
Figure 9. Test Circuit
Table 4. TEST CIRCUIT
TEST
SWITCH
tPLH, tPHL
Open
tPZL, tPLZ
6 V at VCC = 3.3 ± 0.3 V;
VCC × 2 at VCC = 2.5 ± 0.2 V; 1.8 ± 0.15 V
tPZH, tPHZ
GND
CL = 50 pF or equivalent (Includes jig and probe capacitance)
RL = 500 W or equivalent
RT = ZOUT of pulse generator (typically 50 W)
http://onsemi.com
10
6 V or VCC × 2
OPEN
GND
74VCXH16373
PACKAGE DIMENSIONS
TSSOP
DT SUFFIX
CASE 1201−01
ISSUE A
48X
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K REF
0.12 (0.005)
M
T U
S
V
S
T U
S
J J1
25
0.254 (0.010)
M
48
SECTION N−N
B
−U−
L
N
1
24
A
−V−
PIN 1
IDENT.
N
F
DETAIL E
D
0.076 (0.003)
−T− SEATING
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSIONS A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
K
K1
C
M
0.25 (0.010)
−W−
G
H
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
12.40
12.60
6.00
6.20
−−−
1.10
0.05
0.15
0.50
0.75
0.50 BSC
0.37
−−−
0.09
0.20
0.09
0.16
0.17
0.27
0.17
0.23
7.95
8.25
0_
8_
INCHES
MIN
MAX
0.488
0.496
0.236
0.244
−−− 0.043
0.002
0.006
0.020
0.030
0.0197 BSC
0.015
−−−
0.004
0.008
0.004
0.006
0.007
0.011
0.007
0.009
0.313
0.325
0_
8_
DETAIL E
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
74VCXH16373/D