LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only FEATURES * TTL INTERFACE COMPATIBLE * HIGH SPEED OPTIC SIGNAL TRANSMISSION * BUILT-IN LED DRIVER * BUILT-IN CURRENT LIMIT RESISTOR * LOW POWER CONSUMPTION PACKAGE DIMENSIONS 2 1 D N 3 G D D V N VI D D V n i V D N G NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15mm(.006") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 1 of 5 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ABSOLUTE MAXIMUM RATINGS AT TA=25℃ PARAMETER MAXIMUM RATING UNIT -0.5 ~ +7 V -0.5 ~ VDD +0.5 V Supply Voltage (VDD) Input Voltage (VIN) Operating Temperature Range -20 ℃ to + 70 ℃ Storage Temperature Range -30 ℃ to + 80 ℃ Lead Soldering Temperature [1.6mm(.063") From Body] 260℃ for 5 Seconds ELECTRICAL OPTICAL CHARACTERISTICS AT TA=25℃ PARAMETER Transmission Speed SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION NRZ signal Ts － － 13.2 Mbps Operating Voltage VDD 2.75 － 5.25 V Peak Emission Wavelength λPeak 630 650 690 nm Fiber coupling light output Pc -21 -17 -15 dBm *1 Dissipation current IDD － 6 8 mA *2 High level input voltage VIH 2 － － V Low level input voltage VIL － － 0.8 V “LowÆHigh”propagation delay time tPLH － － 166 hs “HighÆLow”propagation delay time tPHL － － 155 hs Pulse width distortion ΔtW -18 － +18 hs Viewing Angle (See FIG.2) 2θ1/2 － 90 － deg. Δtj － 1 18 hs Jitter Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : *3 2 of 5 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only *1 Measuring method of optical output coupling power LTDL-TA12B Optical power meter Standard plastic optical fiber cable V IN Calibrate the optical power meter to sense the light with wavelength 660nm. VDD GND +- VDD 0.1uF *2 Power dissipation measuring method LTDL-TA12B V IN V DD GND 0.1uF A IDD +- VDD Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 3 of 5 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only *3 Measuring pulse response LTDL-TA12B Standard receiver Standard plastic optical fiber cable V IN Output Signal V DD GND +- V DD Oscilloscope Trigger:CH1 0.1uF Input CH1 NRZ code, 12Mbps, "1010..." pattern CH2 50% Input signal (CH1) Standard receiver output (CH2) t PLH Pulse width distortion 50% t PHL tw = t PHL-t PLH Note (1)The impedance of the probe for the oscilloscope must be more than 1MΩ and less than 10pf. Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 4 of 5 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only TYPICAL ELECTRICAL / OPTICAL CHARACTERISTICS CURVES (25℃ Ambient Temperature Unless Otherwise Noted) 0 Relative Radiant Intensity Relative Radiant Intensity 1.0 0.5 0 600 650 700 o 10 o 20 o 30 o 40 o 1.0 0.9 50 o 0.8 60 o 0.7 70 80 90 o 0.5 0.3 0.1 o o 0.2 0.4 0.6 Wavelength (nm) FIG.1 SPECTRAL DISTRIBUTION Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 FIG.2 RADIATION DIAGRAM Page : 5 of 5