MAXIM MAX9164EUD

19-2738; Rev 0; 1/03
3.3V Single LVDS Driver/Receiver
The MAX9164 driver output uses a current-steering
configuration to generate a 3.1mA drive current. The
driver accepts a single-ended input and translates it to
LVDS signals at speeds up to 200Mbps over controlled-impedance media of approximately 100Ω. The
transmission media may be printed circuit board traces
or cables. The enable logic input, DE, is used to enable
or disable the driver.
The MAX9164 receiver detects a differential input as
low as 100mV and translates it to single-ended output
at speeds up to 200Mbps. The enable logic input, RE,
is used to enable or disable the receiver.
Inputs and outputs conform to the ANSI TIA/EIA-644
LVDS standard. The MAX9164 is offered in 14-lead SO
and TSSOP packages, and is specified for operation
from -40°C to +85°C.
Features
♦ 3.3V Operation
♦ 35% Lower Power than DS90LV019
♦ 200Mbps Data Signaling Rate
♦ ±1V Common-Mode Range
♦ ±100mV Receiver Sensitivity
♦ Flow-Through Pinout
♦ Receiver Output High for Open Input
Ordering Information
TEMP RANGE
PIN-PACKAGE
MAX9164ESD
PART
-40°C to +85°C
14 SO
MAX9164EUD
-40°C to +85°C
14 TSSOP
Pin Configuration
TOP VIEW
DE 1
Applications
14 VCC
DIN
2
13 N.C.
N.C.
3
12 DO+
ROUT 4
MAX9164
11 DO-
Cell-Phone Base Stations
Network Switches/Routers
N.C. 5
10 RI+
Add/Drop Muxes
Backplane Interconnect
N.C. 6
9
RI-
Digital Cross-Connects
Clock Distribution
GND 7
8
RE
DSLAMs
SO/TSSOP
Typical Application Circuit
MAX9164
DIN
DO+
RI+
100Ω
DORI+
DE
ROUT
RI-
100Ω
RE
RIDO+
DO-
MAX9164
ROUT
RE
DIN
DE
TABLE 1. DRIVER FUNCTION TABLE
INPUTS
DE
DIN
H
L (≤ 0.8V)
H
H (≥ 2.0V)
H (> 0.8V and < 2.0V)
L
X
X: High or low
Z: High impedance
OUTPUTS
DO+
DOL
H
H
L
Undefined Undefined
Z
Z
TABLE 2. RECEIVER FUNCTION TABLE
INPUTS
OUTPUT
RE
RI+ - RIROUT
L
L (≤ -100mV)
L
L
H(≥ 100mV)
H
L (> -100mV and < 100mV)
Undefined
L
Open
H
H
X
Z
X: High or low
Z: High impedance
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX9164
General Description
The MAX9164 high-speed LVDS driver/receiver is
designed specifically for low-power point-to-point applications. The MAX9164 operates from a single 3.3V
power supply, and is pin compatible with DS90LV019.
The device features an independent differential driver
and receiver.
MAX9164
3.3V Single LVDS Driver/Receiver
ABSOLUTE MAXIMUM RATINGS
VCC to GND ...........................................................-0.3V to +4.0V
DO+, DO-, RI+, RI- to GND...................................-0.3V to +4.0V
DIN, ROUT, DE, RE to GND .......................-0.3V to (VCC + 0.3V)
Driver Short-Circuit Current .......................................Continuous
Continuous Power Dissipation (TA = +70°C)
14-Pin SO (derate 8.3mW/°C above +70°C)................667mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) .........727mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
ESD Protection
HBM (1.5kΩ, 100pF), DO+, DO-, RI+, RI-, DE, RE, DIN,
ROUT ......................................................................> ±2kV
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 3.0V to 3.6V, |VID| = 0.1V to 2.4V, common-mode input voltage (VCM) = |VID/2| to 2.4V - |VID|/2, RL = 100Ω ±1%, TA = -40°C to
+85°C. Typical values are at VCC = 3.3V, |VID| = 0.2V, VCM = 1.2V, TA = +25°C, unless otherwise noted.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SINGLE-ENDED INPUTS (DIN, DE, RE)
Input High Voltage
VIH
2.0
VCC
V
Input Low Voltage
VIL
0
0.8
V
Input Current
IIN
RE, DE, DIN = high or low
-10
+10
µA
VCL
ICLAMP = -18mA
-1.5
VOD
Figure 1
250
∆VOD
Figure 1
VOS
Figure 1
Change in Magnitude of VOS Between
Complementary Output States
∆VOS
Figure 1
High-Impedance Leakage Current
IOZD
DE = 0; DO+, DO- = VCC or 0
-1
Power-Off Leakage Current
IOXD
DO+, DO- = 3.6V or 0; VCC = 0
-1
Input Diode Clamp Voltage
V
DRIVER OUTPUT (DO+, DO-)
Differential Output Voltage
Change in Magnitude of VOD Between
Complementary Output States
Offset Voltage
Output Short-Circuit Current
IOSD
Output Capacitance
CDO
1.0
310
450
mV
0.02
25
mV
1.29
1.7
V
0.8
25
mV
+1
µA
+1
µA
DO+ = 0 at DIN = VCC
-3
-10
DO- = 0 at DIN = 0
-3
-10
Capacitance from DO+ or
DO- to 0
3.7
mA
pF
RECEIVER INPUT (RI+, RI-)
Differential Input High Threshold
VTH
Differential Input Low Threshold
VTL
100
-100
Input Current
IIN
VCC = 3.6V or 0;
RI+, RI- = 2.4V or 0
Input Capacitance
CRI
RI+ or RI- to 0
Output High Voltage
VOH
IOH = -400µA
Output Low Voltage
VOL
IOS
IOL = +2.0mA, VID = -100mV
mV
mV
-10
+10
µA
5
pF
3.28
V
RECEIVER OUTPUT (ROUT)
Output Short-Circuit Current
2
VID = 100mV
RI+, RI- open
VID = +100mV, ROUT = 0
2.9
-20
0.025
0.4
V
-28
-75
mA
_______________________________________________________________________________________
3.3V Single LVDS Driver/Receiver
(VCC = 3.0V to 3.6V, |VID| = 0.1V to 2.4V, common-mode input voltage (VCM) = |VID/2| to 2.4V - |VID|/2, RL = 100Ω ±1%, TA = -40°C to
+85°C. Typical values are at VCC = 3.3V, |VID| = 0.2V, VCM = 1.2V, TA = +25°C, unless otherwise noted.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DE = VCC, RE = 0
7.4
12.5
mA
SUPPLY CURRENT
Supply Current
ICC
Driver Supply Current
ICCD
DE = RE = VCC
7.4
12.5
mA
Receiver Supply Current
ICCR
DE = RE = 0
4.4
7.0
mA
Disable Supply Current
ICCZ
DE = 0, RE = VCC
4.4
7.0
mA
AC ELECTRICAL CHARACTERISTICS
(VCC = 3.0V to 3.6V, |VID| = 0.2V, VCM = 1.2V, RL = 100Ω ±1%, CL = 10pF, TA = -40°C to +85°C. Typical values are at VCC = 3.3V,
|VID| = 0.2V, VCM = 1.2V, TA = +25°C, unless otherwise noted.) (Notes 3, 4, 5)
PARAMETER
SYMBOL
Differential High-to-Low Propagation Delay
tPHLD
Differential Low-to-High Propagation Delay
Differential Skew | tPHLD - tPLHD |
CONDITIONS
MIN
TYP
MAX
UNITS
Figure 2
2.0
4.4
6.5
ns
tPLHD
Figure 2
1.0
4.2
7.0
ns
tSKD
Figure 2
0.2
1.0
ns
Rise Time
tTLHD
Figure 2
0.2
0.9
3.0
ns
Fall Time
tTHLD
Figure 2
0.2
0.8
3.0
ns
Disable Time High to Z
tPHZ
Figure 3
1.5
6.0
8.0
ns
Disable Time Low to Z
tPLZ
Figure 3
2.5
5.5
9.0
ns
Enable Time Z to High
tPZH
Figure 3
4.0
5.5
8.0
ns
Enable Time Z to Low
tPZL
Figure 3
3.8
5.0
8.0
ns
Differential High-to-Low Propagation Delay
tPHL
Figure 4
3.0
5.4
7.0
ns
Differential Low-to-High Propagation Delay
tPLH
Figure 4
3.0
Differential Skew | tPHL - tPLH |
TSK
Figure 4
Rise Time
tTLH
Figure 4
0.15
Fall Time
tTHL
Figure 4
0.15
0.4
3.0
ns
Disable Time High to Z
tPHZ
Figure 5
3.0
5.4
6.0
ns
Disable Time Low to Z
tPLZ
Figure 5
3.0
5.1
6.0
ns
Enable Time Z to High
tPZH
Figure 5
3.0
5.4
8.0
ns
Enable Time Z to Low
tPZL
Figure 5
3.0
5.1
8.0
ns
DRIVER
RECEIVER
5.3
9.0
ns
0.14
1.5
ns
0.8
3.0
ns
Note 1: Maximum and minimum limits over temperature are guaranteed by design and characterization. Devices are 100% tested
at TA = +25°C.
Note 2: Current into a pin is defined as positive. Current out of a pin is defined as negative. All voltages are referenced to device
ground except VTH, VTL, VID, VOD, and ∆VOD.
Note 3: CL includes probe and jig capacitance.
Note 4: AC parameters are guaranteed by design and characterization.
Note 5: Generator waveforms for all tests unless otherwise specified: f = 100MHz, Z0 = 50Ω, tR = tF = 6.0ns (0 to 3V, 0% to 100%)
for DE and RE, tR = tF = 3.0ns (0 to 3V, 0% to 100%) for DIN, and tR = tF = 1.0ns (|VID| = 0.2V, 20% to 80%) for RI+/RIinputs.
_______________________________________________________________________________________
3
MAX9164
DC ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VCC = 3.3V, |VID| = 0.2V, VCM = 1.2V, RL = 100Ω ±1%, FREQ = 100MHz, CL = 10pF, TA = +25°C, unless otherwise noted.)
310
309
308
307
306
3.1
3.2
3.3
3.4
3.5
MAX9164 toc03
9
7
70
0
90 100 110 120 130 140 150
80
25
50
75
100 125 150 175 200
SUPPLY CURRENT (ICC)
vs. TEMPERATURE
DRIVER SUPPLY CURRENT (ICC)
vs. SUPPLY VOLTAGE
DRIVER DIFFERENTIAL PROPAGATION
DELAY vs. SUPPLY VOLTAGE
7.6
7.4
7.2
7.7
DE = HIGH
RE = HIGH
DC CURRENT
7.6
7.5
7.4
7.3
7.2
7.0
-15
10
35
60
3.0
85
3.1
3.2
3.3
3.4
3.5
6.0
MAX9164 toc06
7.8
MAX9164 toc05
MAX9164 toc04
DE = HIGH
RE = LOW
DC CURRENT
DRIVER DIFFERENTIAL PROPAGATION DELAY (ns)
FREQUENCY (MHz)
5.5
5.0
tPHLD
4.5
4.0
tPLHD
3.5
3.0
3.6
3.0
3.1
3.2
3.3
3.4
3.5
TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
DRIVER DIFFERENTIAL PROPAGATION
DELAY vs. TEMPERATURRE
DRIVER DIFFERENTIAL SKEW
vs. SUPPLY VOLTAGE
DRIVER DIFFERENTIAL SKEW
vs. TEMPERATURE
tPHLD
4.5
4.0
tPLHD
3.5
3.0
0.21
0.20
0.19
0.18
0.17
-40
-15
10
35
TEMPERATURE (°C)
60
85
3.6
MAX9164 toc09
0.22
0.35
DRIVER DIFFERENTIAL SKEW (ns)
5.0
0.23
DRIVER DIFFERENTIAL SKEW (ns)
MAX9164 toc07
5.5
MAX9164 toc08
SUPPLY CURRENT (mA)
10
LOAD RESISTANCE (Ω)
7.8
4
11
SUPPLY VOLTAGE (V)
8.0
-40
12
8
60
3.6
DRIVER SUPPLY CURRENT (mA)
3.0
13
DRIVER SUPPLY CURRENT (mA)
311
460
440
420
400
380
360
340
320
300
280
260
240
220
200
180
160
MAX9164 toc02
312
DRIVER DIFFERENTIAL OUTPUT VOLTAGE (mV)
MAX9164 toc01
DRIVER DIFFERENTIAL OUTPUT VOLTAGE (mV)
313
DRIVER SUPPLY CURRENT
vs. FREQUENCY
DRIVER DIFFERENTIAL OUTPUT VOLTAGE
vs. LOAD RESISTANCE
DRIVER DIFFERENTIAL OUTPUT VOLTAGE
vs. SUPPLY VOLTAGE
DRIVER PROPAGATION DELAY (ns)
MAX9164
3.3V Single LVDS Driver/Receiver
0.30
0.25
0.20
0.15
0.10
3.0
3.1
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
3.5
3.6
-40
-15
10
35
TEMPERATURE (°C)
_______________________________________________________________________________________
60
85
3.3V Single LVDS Driver/Receiver
tTHLD
1.0
0.9
0.8
tTLHD
0.7
0.6
tTLHD
1.0
0.8
0.6
tTHLD
0.4
3.0
3.1
3.2
3.3
3.4
3.5
3.6
2.0
1.5
tTHLD
1.0
0
-40
-15
10
35
60
85
10
15
20
25
30
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
CAPACITANCE (pF)
RECEIVER OUTPUT SHORT-CIRCUIT
CURRENT vs. SUPPLY VOLTAGE
RECEIVER OUTPUT HIGH VOLTAGE
vs. SUPPLY VOLTAGE
RECEIVER OUTPUT LOW VOLTAGE
vs. SUPPLY VOLTAGE
25
20
15
10
5
VID = +100mV
3.5
3.4
3.3
3.2
3.1
3.0
ILOAD = -400µA
VID = +100mV
2.9
0.029
2.8
0
3.1
3.2
3.3
3.4
3.5
3.0
3.6
3.1
3.2
3.3
3.4
3.5
0.028
0.027
0.026
0.025
0.024
0.023
ILOAD = 2mA
VID = -100mV
0.022
3.6
3.0
3.1
3.2
3.3
3.4
3.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
RECEIVER DIFFERENTIAL PROPAGATION
DELAY vs. SUPPLY VOLTAGE
RECEIVER DIFFERENTIAL PROPAGATION
DELAY vs. TEMPERATURE
RECEIVER TRANSITION TIME
vs. TOTAL LOAD CAPACITANCE
5.5
5.0
tPLH
4.5
4.0
3.5
3.0
3.0
3.1
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
3.5
3.6
5.75
tPHL
5.50
5.25
tPLH
5.00
3.0
3.6
MAX9164 toc18
tPHL
6.0
6.00
RECEIVER TRANSITION TIME (ns)
MAX9164 toc16
6.5
RECEIVER DIFFERENTIAL PROPAGATION DELAY (ns)
SUPPLY VOLTAGE (V)
7.0
35
MAX9164 toc15
3.6
RECEIVER OUTPUT LOW VOLTAGE (V)
30
MAX9164 toc14
35
3.7
RECEIVER OUTPUT HIGH VOLTAGE (V)
MAX9164 toc13
40
3.0
tTLHD
2.5
0.5
0
3.0
RECEIVER OUTPUT SHORT-CIRCUIT CURRENT (mA)
1.2
0.2
0.5
RECEIVER DIFFERENTIAL PROPAGATION DELAY (ns)
MAX9164 toc11
1.4
3.5
DRIVER TRANSITION TIME (ns)
1.1
DRIVER TRANSITION TIME
vs. TOTAL LOAD CAPACITANCE
MAX9164 toc17
DRIVER TRANSITION TIME (ns)
1.2
1.6
DRIVER TRANSITION TIME (ns)
MAX9164 toc10
1.3
DRIVER TRANSITION TIME
vs. TEMPERATURE
MAX9164 toc12
DRIVER TRANSITION TIME
vs. SUPPLY VOLTAGE
2.5
tTLH
2.0
1.5
tTHL
1.0
0.5
0
4.75
-40
-15
10
35
TEMPERATURE (°C)
60
85
10
15
20
25
30
35
CAPACITANCE (pF)
_______________________________________________________________________________________
5
MAX9164
Typical Operating Characteristics (continued)
(VCC = 3.3V, |VID| = 0.2V, VCM = 1.2V, RL = 100Ω ±1%, FREQ = 100MHz, CL = 10pF, TA = +25°C, unless otherwise noted.)
3.3V Single LVDS Driver/Receiver
MAX9164
Pin Description
PIN
NAME
FUNCTION
1
DE
LVTTL/LVCMOS Driver Enable Input. The driver is enabled when DE is high. When DE is low,
the driver outputs, DO+ and DO-, are disabled and are high impedance.
2
DIN
LVTTL/LVCMOS Driver Input
3, 5, 6, 13
N.C.
No Connection. Not internally connected.
4
ROUT
LVTTL/LVCMOS Receiver Output
7
GND
Ground
8
RE
LVTTL/LVCMOS Receiver Enable Input. The receiver is enabled when RE is low. When RE is
high, the receiver output is disabled and is high impedance.
9
RI-
Inverting LVDS Receiver Input. RI- has an integrated pulldown to GND.
10
RI+
Noninverting LVDS Receiver Input. RI+ has an integrated pullup to VCC.
11
DO-
Inverting LVDS Driver Output
12
DO+
Noninverting LVDS Driver Output
14
VCC
Power-Supply Input. Bypass VCC to GND with 0.1µF and 0.001µF ceramic capacitors.
DO+
RL/2
2.0V
DIN
VOS
VOD
0.8V
RL/2
DO-
Figure 1. Differential Driver DC Test Circuit
6
_______________________________________________________________________________________
3.3V Single LVDS Driver/Receiver
RI+
PULSE
GENERATOR
DO+
DIN
PULSE
GENERATOR
RL
DO-
50Ω
MAX9164
CL
CL
50Ω
50Ω
CL
ROUT
RI-
3V
1.5V
1.5V
0V
DIN
tPLHD
1.3V
RIVCM = 1.2V
RI+
VOD
0V
VID
0V DIFF
tPHLD
DO-
tPHL
tPLH
DO+
1.1V
VOH
80%
80%
VOD
80%
VOD
20%
1.5V
1.5V
0V (DIFFERENTIAL)
DO+ - DO-
80%
20%
ROUT
20%
20%
tTHL
tTLH
tTHLD
tTLHD
Figure 2. Driver Differential Propagation Delay and Transition
Time Test Circuit and Waveforms
Figure 4. Receiver Propagation Delay and Transition Time Test
Circuit and Waveforms
RI+
CL
DO+
2.0V
0.8V
ROUT
RICL
RL/2
DIN
CL
DE
PULSE
GENERATOR
VOL
RL/2
1.2V
PULSE
GENERATOR
DO-
500Ω
VCC
RE
50Ω
50Ω
VCC WHEN ROUT IS LOW,
GND WHEN ROUT IS HIGH.
3V
DE
1.5V
1.5V
DO- (DIN = L)
DO+ (DIN = H)
VOH
0V
tPHZ
50%
50%
VOL
tPZL
50%
1.2V
1.5V
tPHZ
tPZH
ROUT
1.2V
0V
VOH - 0.5V
tPLZ
50%
ROUT
Figure 3. Driver High-Impedance Delay Test Circuit and
Waveforms
1.5V
RE
tPZH
tPLZ
DO- (DIN = H)
DO+ (DIN = L)
3V
VOH
50%
GND
50%
VCC
VOL
tPZL
VOL + 0.5V
Figure 5. Receiver High-Impedance Delay Test Circuit and
Waveforms
_______________________________________________________________________________________
7
MAX9164
3.3V Single LVDS Driver/Receiver
Detailed Description
The MAX9164 high-speed LVDS driver/receiver is
designed specifically for low-power point-to-point
applications. The MAX9164 operates from a single 3.3V
power supply, and is pin compatible with the
DS90LV019. The device features an independent differential driver and receiver.
The MAX9164 driver outputs use a current-steering
configuration to generate a 3.1mA (typ) output current.
This current-steering approach induces less ground
bounce and no shoot-through current, enhancing noise
margin and system speed performance. The outputs
are short-circuit current limited. The MAX9164 output
requires a resistive load to terminate the signal and
complete the transmission loop. With a typical 3.1mA
output current, the MAX9164 produces a 310mV output
voltage when driving a bus terminated with a 100Ω
resistor (3.1mA x 100Ω = 310mV).
The MAX9164 receiver detects a differential input as
low as 100mV and translates it to single-ended output.
The device features input biasing that drives the output
high if the inputs are left open.
The differential output requires a termination resistor at
the far end of the transmission line. This termination
resistor should match the differential impedance of the
output transmission line.
These termination resistors are typically 100Ω. Minimize the distance between the input termination resistor and the MAX9164 receiver input.
Traces, Cables, and Connectors
The characteristics of differential input and output connections affect the performance of the device. Use
controlled-impedance traces, cables, and connectors
with matched characteristic impedance.
Ensure that noise couples as common mode by running the traces of a differential pair close together.
Reduce within-pair skew by matching the electrical
length of the conductors within a differential pair.
Excessive skew can result in a degradation of magnetic field cancellation.
Maintain the distance between conductors within a differential pair to avoid discontinuities in differential
impedance. Minimize the number of vias to further prevent impedance discontinuities.
Power-On Reset
The power-on reset voltage of the MAX9164 is typically
2.2V. When the supply falls below this voltage, the
device is disabled and the outputs (DO+, DO-, and
ROUT) are high impedance.
Board Layout
For LVDS applications, a four-layer PC board with separate power, ground, LVDS, and logic signal layers is
recommended. Separate the LVTTL/LVCMOS and
LVDS signals to prevent coupling.
Applications Information
Power-Supply Bypassing
Bypass V CC with high-frequency, surface-mount
ceramic 0.1µF and 0.001µF capacitors in parallel as
close to the device as possible, with the smaller valued
capacitor closest to VCC.
Chip Information
TRANSISTOR COUNT: 901
PROCESS: CMOS
Termination
The MAX9164 requires an external termination resistor
at the differential input. This termination resistor should
match the differential impedance of the input transmission line.
8
_______________________________________________________________________________________
3.3V Single LVDS Driver/Receiver
N
E
H
INCHES
MILLIMETERS
MAX
MIN
0.069
0.053
0.010
0.004
0.014
0.019
0.007
0.010
0.050 BSC
0.150
0.157
0.228
0.244
0.016
0.050
MAX
MIN
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
1.27 BSC
3.80
4.00
5.80
6.20
0.40
SOICN .EPS
DIM
A
A1
B
C
e
E
H
L
1.27
VARIATIONS:
1
INCHES
TOP VIEW
DIM
D
D
D
MIN
0.189
0.337
0.386
MAX
0.197
0.344
0.394
MILLIMETERS
MIN
4.80
8.55
9.80
MAX
5.00
8.75
10.00
N MS012
8
AA
14
AB
16
AC
D
A
B
e
C
0 -8
A1
L
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, .150" SOIC
APPROVAL
DOCUMENT CONTROL NO.
21-0041
REV.
B
1
1
_______________________________________________________________________________________
9
MAX9164
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
MAX9164
3.3V Single LVDS Driver/Receiver
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
10 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.