TD3063 Zero-Volt Switching Triac Driver DESCRIPTION The TD3063 consists of a single input LED optically coupled to a zero-volt crossing triac driver. The TD3063 provides high input-to-output isolation and is designed to drive high-powered triacs. Typical uses include interfacing logic level control signals to equipment powered from 110Vac and 220Vac lines. FEATURES APPLICATIONS • Zero-volt switching • Home appliances • 600V blocking voltage • Motor/ Drive controls • High input-to-output isolation (5kV) • Solid state relays • Low trigger current (5mA MAX) • Solenoid / Valve control • High reliability • Temperature Control OPTIONS/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* • -S Surface Mount Leadform Option • -TR Tape and Reel Option • -V Signifies VDE approval • -H 0.4" Lead Spacing (see mechanical dimension) NOTE: Suffixes listed above are not included in marking on device for part number identification. SCHEMATIC DIAGRAM + Input - Input 1 6 2 3 PARAMETER UNIT MIN TYP MAX Storage Temperature °C -55 125 Operating Temperature °C -40 85 Continuous Input Current mA 50 Transient Input Current mA 400 Reverse Input Control Voltage V 6 +/- AC Output Total Power Dissipation mW 330 5 Do Not Use Soldering Temperature (10s) ºC 260 4 -/+ AC Output *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. APPROVALS © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 • UL and C-UL Approved File # E201932 • VDE Approved, Lic # 40011225 Page 1 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX 1.2 1.5 TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V LED Reverse Voltage V Reverse Leakage Current µA 6 12 If = 10mA Ir = 10uA 10 Vr = 4V OUTPUT SPECIFICATIONS Blocking Voltage V Peak Blocking Current nA On-state Voltage V Critical Rate of Rise V/ 600 µs Io = 1uA 60 500 Vdrm = Rated 1.8 3 Itm = 100mA 600 COUPLED SPECIFICATIONS Isolation Voltage V Trigger Current mA Inhibit Voltage V Isolation Resistance GΩ Holding Current µA Leakage Current µA © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 5000 T = 1 minute 5 5 Main terminal voltage = 3V 20 If = 5mA 50 DC 500V 100 1 Page 2 of 5 If = Rated, Vdrm = Rated, Off State TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver PERFORMANCE DATA VTM,ON-STATE VOLTAGE (VOLTS) Ta,AMBIENT TEMPERATURE (°C) Ta,AMBIENT TEMPERATURE (°C) Fig.5 Trigger Current versus Temperature IFT , NORMALIZED IDRM2 NORMALIZED Fig.4 IDRM2 ,Leakage in Inhibit State versus Temperature Fig.3 Leakage with LED Off versus Temperature IDRM1,PEAK BLOCKING CURRENT (nA) Fig.2 Inhibit Voltage versus Temperature VINH, NORMALIZED ITM,ON-STATE CURRENT (mA) Fig.1 On-State Characteristics Ta,AMBIENT TEMPERATURE (°C) © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Ta,AMBIENT TEMPERATURE (°C) Page 3 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver MECHANICAL DIMENSIONS 6 PIN DUAL IN-LINE PACKAGE (Through Hole) 6 PIN SURFACE MOUNT DEVICE (SMD) -H Suffix 0.4" Lead Spacing TOLERANCE :+ 0.25mm Unit in (mm) © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 4 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 5 of 5 TD3063 rev 1.40 (10/25/2004)