MAXIM MAX7042_07

19-3704; Rev 1; 3/07
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Ordering Information
PART
Applications
Remote Keyless Entry
Tire-Pressure Monitoring
Home and Office Lighting Control
Remote Sensing
MAX7042ATJ+
-40°C TO
+125°C
32 Thin QFN-EP*
T3255-3
MAX7042AAX+**
-40°C TO
+125°C
36 SSOP
A36-2
+Denotes a lead-free package.
*EP = Exposed paddle.
**Future product—contact factory for availability.
Pin Configuration
Security Systems
DF
OP+
DS+
Local Telemetry Systems
DGND
TOP VIEW
DVDD
Smoke Alarms
Home Automation
PKG
CODE
TEMP RANGE PIN-PACKAGE
24
23
22
21
20
PDMIN
The MAX7042 is available in a 32-pin thin QFN and
is specified over the automotive -40°C to +125°C
temperature range.
DS-
The MAX7042 includes all the active components
required in a superheterodyne receiver including a lownoise amplifier (LNA), an image-rejection (IR) mixer, a
fully integrated phase-locked loop (PLL), local oscillator
(LO), 10.7MHz IF limiting amplifier with received-signalstrength indicator (RSSI), low-noise FM demodulator,
and a 3V regulator. Differential peak-detecting data
demodulators are included for baseband data recovery.
PDMAX
The MAX7042 fully integrated, low-power, CMOS
superheterodyne RF receiver is designed to receive
frequency-shift-keyed (FSK) data at rates up to 66kbps
nonreturn-to-zero (NRZ) (33kbps Manchester). The
MAX7042 requires only a few external components to
realize a complete wireless RF receiver at 308, 315,
418, and 433.92MHz.
Features
♦ +2.4V to +3.6V or +4.5V to +5.5V Single-Supply
Operation
♦ Four User-Selectable Carrier Frequencies
308, 315, 418, and 433.92MHz
♦ -110dBm RF Input Sensitivity at 315MHz
♦ -109dBm RF Input Sensitivity at 433.92MHz
♦ Fast Startup (< 250µs)
♦ Small 32-Pin Thin QFN Package
♦ Low Operating Supply Current
6.2mA Continuous
20nA Power-Down
♦ Integrated PLL, VCO, and Loop Filter
♦ 45dB Integrated Image Rejection
♦ Selectable IF BW with External Filter
♦ Positive and Negative Peak Detectors
♦ RSSI Output
19
18
17
N.C.
25
16
IFIN+
EN
26
15
IFIN-
FSEL1
27
14
AGND
FSEL2
28
13
MIXOUT
MAX7042
HVIN
29
12
MIXIN-
DATA
30
11
MIXIN+
LNASEL
31
10
LNAOUT
N.C.
32
9
LNASRC
5
6
7
8
XTAL1
AVDD
LNAIN
N.C.
4
XTAL2
3
RSSI
2
N.C.
Typical Application Circuit appears at end of data sheet.
1
N.C.
+
THIN QFN
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX7042
General Description
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
ABSOLUTE MAXIMUM RATINGS
HVIN to AGND or DGND .......................................-0.3V to +6.0V
AVDD, DVDD to AGND or DGND..........................-0.3V to +4.0V
FSEL1, FSEL2, LNASEL,
EN, DATA...............................(DGND - 0.3V) to (HVIN + 0.3V)
All Other Pins............................(AGND - 0.3V) to (AVDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
32-Pin Thin QFN (derate 34.5mW/°C above +70°C)....2759mW
Operating Temperature Range .........................-40°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Maximum RF Input Power ................................................+0dBm
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(Typical Application Circuit, 50Ω system impedance, AVDD = DVDD = HVIN = +2.4V to +3.6V, fRF = 308, 315, 418, and 433.92MHz;
T A = -40°C to +125°C, unless otherwise noted. Typical values are at AV DD = DV DD = HV IN = +3.0V, f RF = 433.92MHz,
PRFIN ≤ -80dBm, TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Supply Voltage (3V)
VDD
HVIN, AVDD, and DVDD connected
to power supply
2.4
3.0
3.6
V
Supply Voltage (5V)
HVIN
HVIN connected to power supply,
AVDD and DVDD unconnected from
HVIN, but connected together
4.5
5.0
5.5
V
315MHz (3V)
315MHz (5V)
Supply Current
IDD
434MHz (3V)
434MHz (5V)
Shutdown Current (3V)
Shutdown Current (5V)
Startup Time
ISHDN
ISHDN
tON
All digital
inputs low
All digital
inputs low
Operating, 1x ILNA
6.2
Operating, 2x ILNA
6.8
Operating, 1x ILNA
6.4
Operating, 2x ILNA
7.0
Operating, 1x ILNA
6.4
8.7
Operating, 2x ILNA
7.0
8.6
Operating, 1x ILNA
6.6
8.4
Operating, 2x ILNA
7.2
9.2
TA = +25°C
0.02
TA = +85°C
0.1
TA = +125°C
0.85
TA = +25°C
0.6
TA = +85°C
1.4
TA = +125°C
4
Time from EN = high to final signal
detection; does not include
baseband filter or dataslicer reference settling
mA
µA
6
µA
7
250
µs
DIGITAL I/O
Input High Threshold
VIH
Input Low Threshold
VIL
2
0.9 x HVIN
V
0.1 x HVIN
_______________________________________________________________________________________
V
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
(Typical Application Circuit, 50Ω system impedance, AVDD = DVDD = HVIN = +2.4V to +3.6V, fRF = 308, 315, 418, and 433.92MHz;
T A = -40°C to +125°C, unless otherwise noted. Typical values are at AV DD = DV DD = HV IN = +3.0V, f RF = 433.92MHz,
PRFIN ≤ -80dBm, TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
Input High Pulldown Current
IIH
Input Low-Leakage Current
IIL
TYP
MAX
HVIN = +3.6V
CONDITIONS
8
15
HVIN = +5.5V
20
40
HVIN = +3.6V
<1
1
HVIN = +5.5V
<1
1
Output High Voltage
VOH
ISOURCE = 500µA
Output Low Voltage
VOL
ISINK = 500µA
MIN
UNITS
µA
µA
HVIN - 0.4
V
0.4
V
VOLTAGE REGULATOR
Output Voltage
VREG
2.5
3.0
3.5
V
AC ELECTRICAL CHARACTERISTICS
(Typical Application Circuit, 50Ω system impedance, AVDD = DVDD = HVIN = +2.4V to +3.6V, fRF = 308, 315, 418, and 433.92MHz;
T A = -40°C to +125°C, unless otherwise noted. Typical values are at AV DD = DV DD = HV IN = +3.0V, f RF = 433.92MHz,
PRFIN ≤ -80dBm, TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
Maximum Input Level
MIN
TYP
0
315MHz
setting
Operating, 1x ILNA
-107
Operating, 2x ILNA
-110
434MHz
setting
Operating, 1x ILNA
-106
Operating, 2x ILNA
-109
Sensitivity (Note 1)
Receiver Image Rejection
45
MAX
UNITS
dBm
dBm
dB
LNA/MIXER
Input Impedance (Note 2)
Z11
1dB Input Compression Point
(Notes 2, 3)
P1dB
Input-Referred 3rd-Order Intercept
Point (Notes 2, 3)
IIP3
Normalized to 2x ILNA 315MHz
50Ω
2x ILNA 433.92MHz
1x ILNA 315MHz
-52
1x ILNA 315MHz
-37
2x ILNA 315MHz
-42
ZoutMIX
1x ILNA 315MHz
330Ω IF filter
load
(Notes 2, 3)
Voltage Conversion Gain
-47
2x ILNA 315MHz
LO Signal Feedthrough to
Antenna
Mixer Output Impedance
0.94 - j3.2
0.94 - j2.1
dBm
dBm
-80
dBm
330
Ω
52
2x ILNA 315MHz
57
1x ILNA 433.92MHz
47
2x ILNA 433.92MHz
52
dB
IF LIMITING AMPLIFIER
Input Impedance
-3dB Bandwidth
Z11
330
Ω
10
MHz
_______________________________________________________________________________________
3
MAX7042
DC ELECTRICAL CHARACTERISTICS (continued)
AC ELECTRICAL CHARACTERISTICS (continued)
(Typical Application Circuit, 50Ω system impedance, AVDD = DVDD = HVIN = +2.4V to +3.6V, fRF = 308, 315, 418, and 433.92MHz;
T A = -40°C to +125°C, unless otherwise noted. Typical values are at AV DD = DV DD = HV IN = +3.0V, f RF = 433.92MHz,
PRFIN ≤ -80dBm, TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
Operating Frequency
CONDITIONS
MIN
TYP
fIF
MAX
UNITS
10.7
RSSI Slope
MHz
10
16
21
mV/dB
1.1
2.1
3.0
mV/kHz
FSK DEMODULATOR
Conversion Gain
ANALOG BASEBAND
Maximum Peak-Detector Bandwidth
50
kHz
Maximum Data-Filter Bandwidth
BWDF
50
kHz
Maximum Data-Slicer Bandwidth
BWDS
100
kHz
Maximum Data Rate
Manchester coded
33
NRZ
66
kHz
CRYSTAL OSCILLATOR
Crystal Frequency
fXTAL
Crystal Load Capacitance
(fRF - 10.7)
/ 32
MHz
4.5
pF
Note 1: 0.2% BER, 4kbps, Manchester coded, 280kHz IF BW, ±50kHz frequency deviation.
Note 2: Input impedance is measured at the LNAIN pin 2x ILNA. Note that the impedance at 315MHz includes the 3.9nH inductive
degeneration from the LNA source to ground. The impedance at 433.92MHz includes a 0nH inductive degeneration connected from the LNA source to ground. The equivalent input circuit is 47Ω in series with 3.2pF at 315MHz and 47Ω in series
with 3.5pF at 433.92MHz.
Note 3: The voltage conversion gain is measured with the LNA input matching inductor, the degeneration inductor, and the
LNA/mixer resonator in place, and does not include the IF filter insertion loss.
Typical Operating Characteristics
(Typical Application Circuit, VDD = 3.0V, fRF = 433.92MHz, IF BW = 280kHz, data rate = 4kbps Manchester encoded, frequency
deviation = ±50kHz, BER = 0.2%, TA = +25°C, unless otherwise noted.)
6.4
6.2
+25°C
6.0
5.8
7.6
+85°C
7.4
7.2
7.0
+25°C
6.8
7.0
6.8
6.6
6.6
+125°C
6.4
+85°C
+25°C
6.2
6.0
6.4
5.6
6.2
-40°C
5.4
5.8
-40°C
6.0
2.4
2.7
3.0
3.3
SUPPLY VOLTAGE (V)
4
+125°C
SUPPLY CURRENT (mA)
6.6
SUPPLY CURRENT vs. RF FREQUENCY
(1x ILNA)
MAX7042 toc02
+85°C
6.8
7.8
SUPPLY CURRENT (mA)
+125°C
7.0
8.0
MAX7042 toc01
7.2
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(2x ILNA)
MAX7042 toc03
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(1x ILNA)
SUPPLY CURRENT (mA)
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
3.6
-40°C
5.6
2.4
2.7
3.0
3.3
SUPPLY VOLTAGE (V)
3.6
300
325
350
375
400
RF FREQUENCY (MHz)
_______________________________________________________________________________________
425
450
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
+85°C
6.9
+25°C
6.7
6.5
MAX7042 toc05
100
800
fRF = 433.92MHz
10
BIT-ERROR RATE
7.1
1000
DEEP-SLEEP CURRENT (nA)
+125°C
7.3
600
VCC = +3.6V
400
VCC = +3.0V
0.2% BER
0.1
VCC = +2.4V
200
1
fRF = 315MHz
-40°C
6.3
0.01
0
6.1
300
325
350
375
400
425
-40
450
-15
10
35
60
85
-114
110
-112
-110
-106
-108
-104
RF FREQUENCY (MHz)
TEMPERATURE (°C)
AVERAGE INPUT POWER (dBm)
BIT-ERROR RATE vs. AVERAGE INPUT POWER
(2x ILNA)
SENSITIVITY vs. TEMPERATURE
(1x ILNA)
SENSITIVITY vs. TEMPERATURE
(2x ILNA)
-106
MAX7042 toc08
fRF = 433.92MHz
-103
MAX7042 toc07
100
-104
MAX7042 toc09
SUPPLY CURRENT (mA)
MAX7042 toc04
7.5
BIT-ERROR RATE vs. AVERAGE INPUT POWER
(1x ILNA)
DEEP-SLEEP CURRENT vs. TEMPERATURE
MAX7042 toc06
SUPPLY CURRENT vs. RF FREQUENCY
(2x ILNA)
-107
1
0.2% BER
SENSITIVITY (dBm)
SENSITIVITY (dBm)
BIT-ERROR RATE
10
-105
-106
fRF = 433.92MHz
-107
-108
-109
fRF = 433.92MHz
-110
0.1
-108
fRF = 315MHz
0.01
-109
-113
-111
-109
-112
-40
-15
10
35
60
85
110
-40
-15
10
35
60
85
110
TEMPERATURE (°C)
TEMPERATURE (°C)
SENSITIVITY
vs. FREQUENCY DEVIATION
RSSI AND DELTA
vs. IF INPUT POWER
FSK DEMODULATOR OUTPUT
vs. IF FREQUENCY
2
RSSI
1
0.9
0
-108
0.6
-1
-110
0.3
RSSI (V)
-104
-106
DELTA
-2
0
-112
10
FREQUENCY DEVIATION (kHz)
100
-3
-90
-70
-50
2.0
-30
RF INPUT POWER (dBm)
-10
10
DELTA (%)
1.5
3
MAX7042 toc12
MAX7042 toc11
1.8
1.2
1
fRF = 315MHz
AVERAGE INPUT POWER (dBm)
FREQUENCY DEVIATION IS
MEASURED FROM 0 TO PEAK
-102
-107
FSK DEMODULATION OUTPUT (V)
-100
-115
MAX7042 toc10
-117
SENSITIVITY (dBm)
-111
fRF = 315MHz
1.6
1.2
0.8
0.4
0
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11.0
IF FREQUENCY (MHz)
_______________________________________________________________________________________
5
MAX7042
Typical Operating Characteristics (continued)
(Typical Application Circuit, VDD = 3.0V, fRF = 433.92MHz, IF BW = 280kHz, data rate = 4kbps Manchester encoded, frequency
deviation = ±50kHz, BER = 0.2%, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(Typical Application Circuit, VDD = 3.0V, fRF = 433.92MHz, IF BW = 280kHz, data rate = 4kbps Manchester encoded, frequency
deviation = ±50kHz, BER = 0.2%, TA = +25°C, unless otherwise noted.)
SYSTEM GAIN vs. IF FREQUENCY
(2x ILNA)
45dB IMAGE
REJECTION
20
10
SYSTEM GAIN (dB)
FROM RFIN
TO MIXOUT
fRF = 433.92MHz
30
50
LOWER SIDEBAND
40
FROM RFIN
TO MIXOUT
fRF = 433.92MHz
45dB IMAGE
REJECTION
30
60
IMAGE REJECTION (dB)
UPPER SIDEBAND
UPPER SIDEBAND
MAX7042 toc14
40
60
MAX7042 toc13
50
IMAGE REJECTION vs. TEMPERATURE
(1x ILNA)
20
LOWER SIDEBAND
10
0
5
10
15
20
25
30
5
0
10
IF FREQUENCY (MHz)
15
20
25
20
-15
35
MAX7042 toc17
-3
fRF = 315MHz
30
20
10
-6
-9
-12
-15
0
-18
-40
-15
10
35
60
85
110
10
1
TEMPERATURE (°C)
100
IF FREQUENCY (MHz)
S11 vs. RF FREQUENCY
MAX7042 toc18
0
S11 (dB)
-4
-8
433.92MHz
-12
-16
100
250
400
550
700
850
1000
RF FREQUENCY (MHz)
6
60
TEMPERATURE (°C)
0
MAX7042 toc16
fRF = 433.92MHz
10
NORMALIZED IF GAIN
vs. IF FREQUENCY
NORMALIZED IF GAIN (dB)
IMAGE REJECTION (dB)
30
IF FREQUENCY (MHz)
60
40
fRF = 315MHz
-40
30
IMAGE REJECTION vs. TEMPERATURE
(2x ILNA)
50
40
0
-10
0
fRF = 433.92MHz
10
0
-10
50
MAX7042 toc15
SYSTEM GAIN vs. IF FREQUENCY
(1x ILNA)
SYSTEM GAIN (dB)
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
_______________________________________________________________________________________
85
110
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
INPUT IMPEDANCE
vs. INDUCTIVE DEGENERATION
S11 SMITH PLOT OF RFIN
MAX7042 toc20
MAX7042 toc19
70
-150
433.92MHz
60
-160
50
-170
40
-180
REAL IMPEDANCE
30
IMAGINARY IMPEDANCE (Ω)
REAL IMPEDANCE (Ω)
fRF = 315MHz
-190
IMAGINARY
IMPEDANCE
20
-200
10
1
100
INDUCTIVE DEGENERATION (nH)
PHASE NOISE
vs. OFFSET FREQUENCY
INPUT IMPEDANCE
vs. INDUCTIVE DEGENERATION
fRF = 433.92MHz
-70
-100
fRF = 315MHz
IMAGINARY
IMPEDANCE
-120
50
REAL IMPEDANCE
40
-130
-80
PHASE NOISE (dBc/Hz)
-110
70
IMAGINARY IMPEDANCE (Ω)
REAL IMPEDANCE (Ω)
80
60
MAX7042 toc22
MAX7042 toc21
90
fRF = 433.92MHz
-90
-100
-110
-120
30
-140
20
1
10
INDUCTIVE DEGENERATION (nH)
100
-130
100
1k
10k
100k
1M
10M
OFFSET FREQUENCY (Hz)
_______________________________________________________________________________________
7
MAX7042
Typical Operating Characteristics (continued)
(Typical Application Circuit, VDD = 3.0V, fRF = 433.92MHz, IF BW = 280kHz, data rate = 4kbps Manchester encoded, frequency
deviation = ±50kHz, BER = 0.2%, TA = +25°C, unless otherwise noted.)
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
MAX7042
Pin Description
8
PIN
NAME
1, 2
N.C.
No Connection. Internally pulled down.
FUNCTION
3, 25, 32
N.C.
No Connection. Not internally connected.
4
RSSI
Buffered Received-Signal-Strength-Indicator Output
5
XTAL2
Crystal Input 2. XTAL2 can be driven from an AC-coupled external reference.
6
XTAL1
Crystal Input 1. Bypass to GND if XTAL2 is driven by an AC-coupled external reference.
7
AVDD
Analog Power-Supply Voltage. AVDD is connected to an on-chip +3.0V regulator in +5V operation.
Bypass AVDD to GND with 0.1µF and 220pF capacitors placed as close to the pin as possible.
8
LNAIN
Low-Noise Amplifier Input. Must be AC-coupled.
9
LNASRC
Low-Noise Amplifier Source for External Inductive Degeneration. Connect an inductor to GND to set
the LNA input impedance.
10
LNAOUT
Low-Noise Amplifier Output. Connect to AVDD through a parallel LC tank filter. AC-couple to MIXIN+.
11
MIXIN+
Noninverting Mixer Input. Must be AC-coupled to the LNA output.
12
MIXIN-
Inverting Mixer Input. Bypass to AVDD or AGND with a capacitor.
13
MIXOUT
330Ω Mixer Output. Connect to the input of the 10.7MHz IF filter.
14
AGND
15
IFIN-
Inverting 330Ω IF Limiter Amplifier Input. Bypass to AGND with a capacitor.
16
IFIN+
Noninverting 330Ω IF Limiter Amplifier Input. Connect to the output of the 10.7MHz IF filter.
Analog Ground
17
PDMIN
Minimum-Level Peak Detector for Demodulator Output
18
PDMAX
Maximum-Level Peak Detector for Demodulator Output
19
DS-
Inverting Data-Slicer Input
20
DS+
Noninverting Data-Slicer Input
21
OP+
Noninverting Op-Amp Input for the Sallen-Key Data Filter
22
DF
23
DGND
Data-Filter Feedback Node. Input for the feedback of the Sallen-Key data filter.
Digital Ground
24
DVDD
Digital Power-Supply Voltage. Bypass to DGND with 0.01µF and 220pF capacitors placed as close to
the pin as possible.
26
EN
Enable. Internally pulled down. Drive high for normal operation. Drive low or leave unconnected to put
the device into shutdown mode.
27
FSEL1
Frequency-Select Pin 1 (see Table 1). Internally pulled down. Connect to EN for logic-high operation.
28
FSEL2
Frequency-Select Pin 2 (see Table 1). Internally pulled down. Connect to EN for logic-high operation.
29
HVIN
High-Voltage Supply Input. For +3V operation, connect HVIN to AVDD and DVDD. For +5V operation,
connect only HVIN to +5V. Bypass HVIN to AGND with 0.01µF and 220pF capacitors placed as close
to the pin as possible.
30
DATA
Receiver Data Output
31
LNASEL
EP
GND
LNA Bias Current Select Pin. Internally pulled down. Set LNASEL to logic-low for low LNA current and
set LNASEL to logic-high for high LNA current. Connect to EN for logic-high operation.
Exposed Paddle. Connect to ground.
_______________________________________________________________________________________
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
LNAOUT
MIXIN+
MIXIN-
10
11
12
MIXOUT IFIN-
13
IFIN+
15
16
IMAGE
REJECTION
LNAIN
8
LNASRC
9
LNA
0˚
Σ
90˚
XTAL2
6
CRYSTAL
OSCILLATOR
AGND 14
XTAL1
IF LIMITING
AMPS
DIVIDEBY-32
RSSI
4
RSSI
VCO
FSK
FSK
DEMODULATOR
5
PHASE
DETECTOR
27 FSEL1
RDF1
100kΩ
LOOP
FILTER
EN 26
RDF2
100kΩ
DVDD 24
EXPOSED
PADDLE*
MAX7042
FSK
DATA
FILTER
DGND 23
HVIN 29
AVDD
7
28 FSEL2
31 LNASEL
3.0V
REG
3.0V
30
19
18
17
DATA
DS-
PDMAX
PDMIN
20
21
22
DS+
OP+
DF
*MUST BE CONNECTED TO AGND.
_______________________________________________________________________________________
9
MAX7042
Functional Diagram
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Detailed Description
The MAX7042 CMOS superheterodyne receiver and a
few external components provide a complete FSK
receive chain from the antenna to the digital output
data. FSK uses the difference in frequency of the carrier to represent a logic 0 and logic 1. Depending on signal power and component selection, data rates as high
as 66kbps NRZ can be achieved.
Frequency Selection
The MAX7042 can be tuned to one of four frequencies
using the 2 frequency-select bits FSEL1 and FSEL2:
308, 315, 418, and 433.92MHz, as shown in Table 1.
The LO frequencies are 32 times the reference crystal
frequencies of 9.29063, 9.50939, 12.72813, and
13.22563MHz. The selected crystal frequency is used
to calibrate the FSK detector PLL so that it operates at
the middle of the 10.7MHz IF.
Table 1. Frequency Selection Table
FSEL2
FSEL1
FREQUENCY
(MHz)
0
0
308
0
1
315
1
0
418
1
1
433.92
Low-Noise Amplifier (LNA)
The LNA is a cascode amplifier with off-chip inductive
degeneration. The gain and the noise figure are dependent on both the antenna matching network at the LNA
input and the LC tank network between the LNA output
and the mixer input.
The MAX7042 allows for user programmability of the
LNA bias current. Input LNASEL programs 1x to 2x
bias currents in increments of 0.6mA from 0.6mA to
1.2mA. Setting LNASEL to logic-low programs the LNA
to consume 1x bias current and setting LNASEL to
logic-high programs the LNA to consume 2x bias current. Larger bias currents yield better sensitivity and
gain at the expense of current drain.
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to AGND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible match to a low-input
10
impedance such as printed circuit board (PCB) trace
antenna. A nominal value of this inductor for a 50Ω input
impedance is 3.9nH at 315MHz and 0nH (short) at
433.92MHz, but is affected by the PCB trace. See the
Typical Operating Characteristics for the relationship
between the inductance and input impedance.
The LC tank filter connected to LNAOUT consists of L2
and C9 (see the Typical Application Circuit). Select L2
and C9 to resonate at the desired RF input frequency.
The resonant frequency is given by:
f =
1
2π LTOTAL x CTOTAL
where LTOTAL = L2 + LPARASITICS and CTOTAL = C9 +
CPARASITICS.
LPARASITICS and CPARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, LNA output impedance, etc. These
parasitics at high frequencies cannot be ignored, and
can have a dramatic effect on the tank filter center frequency. Lab experimentation is required to optimize the
center frequency of the tank. The parasitic capacitance
is generally 5pF to 7pF.
There are two ways to verify experimentally that the resonant frequency of the tank is centered at the desired
RF frequency:
1) Drive the crystal oscillator externally and sweep both
the RF frequency and the LO frequency (FXTAL x
32) to keep the IF at 10.7MHz while monitoring the
RSSI voltage (pin 4). There is a peak in the RSSI
voltage at resonance. The external source must be
AC-coupled into XTAL1 and the XTAL2 pin must
have an AC bypass to ground. The recommended
drive power is -10dBm.
2) Use a network analyzer to measure the resonance.
The port 1 power from the network analyzer is input
to the receiver, and this power must be -30dBm or
less. A coaxial stub with the center conductor
exposed (commonly called an RF “sniffer” is used to
monitor the tank power and serves as the port 2
input to the network analyzer. The sniffer should be
placed in close proximity to, but not actually touching, the tank inductor.
______________________________________________________________________________________
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
MAX7042
TO FSK
BASEBAND FILTER
AND DATA SLICER
IF
LIMITING
AMPS
PHASE
DETECTOR
CHARGE
PUMP
LOOP
FILTER
10.7MHz VCO
2.1mV/kHz
Figure 1. FSK Demodulator PLL Block Diagram
Mixer
Intermediate Frequency (IF)
A unique feature of the MAX7042 is the integrated image
rejection of the mixer. This device is designed to eliminate the need for a costly front-end SAW filter in many
applications. The advantages of not using a SAW filter
are increased sensitivity, simplified antenna matching,
less board space, and lower cost.
The mixer cell is a pair of double-balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz intermediate frequency (IF) with low-side
injection (i.e., fLO = fRF - fIF). The image-rejection circuit
then combines these signals to achieve a typical image
rejection of approximately 45dB. Low-side injection is
required as high-side injection is not possible due to
the on-chip image rejection. The IF output is driven by
a source follower, biased to create a driving impedance of 330Ω to interface with an off-chip 330Ω ceramic IF filter. Note that MIXIN+ and MIXIN- are functionally
identical.
The IF section presents a differential 330Ω load to provide matching for the off-chip ceramic filter. The internal six AC-coupled limiting amplifiers produce an
overall gain of approximately 65dB. The limiting amplifiers have a bandpass-filter-type response centered
near the 10.7MHz IF frequency with a 3dB bandwidth
of approximately 10MHz. The limiter output is fed into a
PLL to demodulate the IF, producing a baseband voltage with a demodulation slope of 2.1mV/kHz. The RSSI
circuit produces a DC output proportional to the log of
the IF signal level with a slope of approximately
16mV/dB.
Phase-Locked Loop (PLL)
The PLL block contains a phase detector, charge
pump/integrated loop filter, voltage-controlled oscillator
(VCO), asynchronous 32x frequency divider, and crystal oscillator. This PLL does not require any external
components. The relationship between the RF, IF, and
reference frequencies is given by:
fREF =
(fRF − fIF)
32
To allow the smallest possible IF bandwidth (for best
sensitivity), minimize the tolerance of the reference.
FSK Demodulator
The FSK demodulator uses an integrated 10.7MHz PLL
that tracks the input RF modulation and determines the
difference between frequencies as logic ones and
zeros. The PLL is illustrated in Figure 1. The input to the
PLL comes from the output of the IF limiting amplifiers.
The PLL control voltage responds to changes in the frequency of the input signal with a nominal gain of
2.1mV/kHz. For example, an FSK peak-to-peak deviation of 50kHz generates a 105mVP-P signal on the control line. This control line is then filtered and sliced by
the FSK baseband circuitry.
The FSK demodulator PLL requires calibration to overcome variations in process, voltage, and temperature.
The maximum calibration time is 120µs, which is included in the startup time. Recalibration is necessary after a
significant change in temperature or supply voltage.
Calibration occurs automatically each time the
MAX7042 is powered up. Drive EN low and then high to
force a recalibration. EN must be driven from low to
high after the MAX7042 supply voltage is stable for
proper initial FSK calibration.
______________________________________________________________________________________
11
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Crystal Oscillator
Frequency Tolerance
The XTAL oscillator in the MAX7042 is used to generate
the LO for mixing with the received signal. The XTAL oscillator frequency sets the received signal frequency as:
fRECEIVE = (fXTAL x 32) + 10.7MHz
The received image frequency at:
fIMAGE = (fXTAL x 32) - 10.7MHz
The frequency tolerance of the crystal, the frequency
and bandwidth tolerance of the IF filter, and the desired
modulation bandwidth of the signal are all interrelated.
The combination of these characteristics should be such
to ensure that the modulated signal bandwidth stays
within the passband of the IF filter after downconversion.
As is shown below, a 50ppm tolerance crystal in combination with a 280kHz bandwidth IF filter is sufficient for
most FSK-modulated signals.
Smaller IF filter bandwidths can be used if high-tolerance
crystals are used for generating both transmitter and
MAX7042 receiver PLL references. The modulated spectrum of the transmitted signal must be downconverted by
the MAX7042 to fall within the passband of the IF filter.
The crystal tolerances must take into account the initial
+25°C tolerance, aging, load capacitance tolerances,
and temperature drift for both the transmitter and
MAX7042 receiver. To achieve acceptable signal reception, the following equation must hold:
2 x (∆FTX + ∆FRX + ∆FIF + FDEV + 5 x FMOD) < IFBWmin
is suppressed by the integrated quadrature imagerejection circuitry.
The XTAL oscillator in the MAX7042 is designed to present a capacitance of approximately 3pF between
XTAL1 and XTAL2. In most cases, this corresponds to a
4.5pF load capacitance applied to the external crystal
when typical PCB parasitics are added. It is very important to use a crystal with a load capacitance that is equal
to the capacitance of the MAX7042 crystal oscillator plus
PCB parasitics. If a crystal designed to oscillate with a
different load capacitance is used, the crystal is pulled
away from its intended operating frequency, introducing
an error in the reference frequency. Crystals designed to
operate with higher differential load capacitance always
pull the reference frequency higher.
In reality, the oscillator pulls every crystal. A crystal’s natural frequency is really below its specified frequency, but
when loaded with the specified load capacitance, the
crystal is pulled and oscillates at its specified frequency.
This pulling is accounted for in the specification of the
load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency
pulling is given by:
fp =

1
1
Cm 
−
x 106

2  Ccase + Cload
Ccase + Cspec 
where:
fp is the amount the crystal frequency is pulled in ppm.
Cm is the motional capacitance of the crystal.
Ccase is the case capacitance.
Cspec is the specified load capacitance.
Cload is the actual load capacitance.
When the crystal is loaded as specified, i.e., Cload =
Cspec, the frequency pulling equals zero.
12
where:
∆FTX = (transmitter crystal tolerance in ppm) x (carrier
frequency in MHz). This includes aging, load capacitance, and temperature effects for the crystal tolerance.
∆FRX = (MAX7042 crystal tolerance in ppm) x (carrier
frequency in MHz). This includes aging, load capacitance, and temperature effects for the crystal tolerance.
∆FIF = The center frequency tolerance of the selected
IF filter. This includes temperature drift of the IF filter
center frequency.
FDEV = ±FSK frequency deviation from carrier frequency.
FMOD = One half of NRZ data rate, or the data rate if
Manchester coding is used.
IFBWmin = The minimum bandwidth of the selected IF
filter.
As an example, assume 315MHz carrier frequency,
±50ppm crystal tolerances for both transmitter and
MAX7042, ±30kHz IF filter center frequency tolerance,
±50kHz frequency deviation, and 4.8kHz Manchester
data rate:
2 x [(315 x 50) + (315 x 50) + 30000 +50000 + 5 x
4800] = 271kHz < IFBWmin
This operating condition necessitates a 280kHz IF filter.
______________________________________________________________________________________
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Table 2. Coefficients to Calculate CF1 and
CF2
FILTER TYPE
a
b
Butterworth
(Q = 0.707)
1.414
1.000
Bessel
(Q = 0.577)
1.3617
0.618
The configuration shown in Figure 2 creates a Butterworth
or Bessel response. The Butterworth filter offers a very
flat amplitude response in the passband and a rolloff rate
of 40dB/decade for the two-pole filter. The Bessel filter
has a linear phase response, which works well for filtering digital data. To calculate the value of the capacitors,
use the following equations along with the coefficients in
Table 2:
b
a(100kΩ)(π)(fC)
a
CF2 =
4(100kΩ)(π)(fC)
CF1 =
MAX7042
FSK DEMOD
100kΩ
DS+
OP+
CF2
100kΩ
DF
CF1
Figure 2. Sallen-Key Lowpass Data Filter
where fC is the desired 3dB corner frequency.
For example, choose a Butterworth filter response with
a 5kHz corner frequency:
1.000
≈ 450pF
(1.414)(100kΩ)(3.14)(5kHz)
1.414
CF2 =
≈ 225pF
(4)(100kΩ)(3.14)(5kHz)
CF1 =
Choosing standard capacitor values changes CF1 to
470pF and C F2 to 220pF. In the Typical Application
Circuit, CF1 and CF2 are named C4 and C3, respectively.
Data Slicer
The purpose of a data slicer is to take the analog output
of a data filter and convert it to a digital signal. This is
achieved by using a comparator and comparing the analog input to a threshold voltage. The threshold voltage is
set by the voltage on the DS- pin, which is connected to
the negative input of the data-slicer comparator. The positive input of the data-slicer comparator is connected to
the output of the data filter internally.
______________________________________________________________________________________
13
MAX7042
Data Filters
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the combination of two on-chip resistors and two external
capacitors. Adjusting the value of the external capacitors changes the corner frequency to optimize for different data rates. The corner frequency in kHz should
be to approximately the fastest expected data rate in
kbps for NRZ and twice the fastest expected data rate
in kbps for Manchester coding from the transmitter.
Keeping the corner frequency near the data rate
rejects any noise at higher frequencies, resulting in an
increase in receiver sensitivity.
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Numerous configurations can be used to generate the
data-slicer threshold. For example, the circuit in Figure 3
shows a simple method using only one resistor and one
capacitor. This configuration averages the analog output of the filter and sets the threshold to approximately
50% of that amplitude. With this configuration, the
threshold automatically adjusts as the analog signal
varies, minimizing the possibility for errors in the digital
data. The values of R and C affect how fast the threshold tracks the analog amplitude. Be sure to keep the
corner frequency of the RC circuit much lower than the
lowest expected data rate.
With this configuration, a long string of zeros or ones
can cause the threshold to drift. This configuration
works best if a coding scheme, such as Manchester
coding, which has an equal number of zeros and ones,
is used.
Figure 4 shows a configuration that uses the positive and
negative peak detectors to generate the threshold. This
configuration sets the threshold to the midpoint between
a high output and a low output of the data filter.
Peak Detectors
The maximum peak detector (PDMAX) and minimum
peak detector (PDMIN) outputs, in conjunction with a
resistor and capacitor connected to GND, create DC
output voltages proportional to the high- and low-peak
values of the data signal. The resistor provides a path
for the capacitor to discharge, allowing the peak detector to dynamically follow peak changes of the data-filter
output voltage.
The positive and negative peak detectors can be used
together to form a data-slicer threshold voltage at a
midvalue between the most positive and most negative
voltage levels of the data stream (see the Data Slicers
section and Figure 4). Set the RC time constant of the
peak-detector combining network to at least 5 times the
data period.
The MAX7042 peak detectors track the baseband filter
output voltage until all internal circuits are stable following an enable pin low-to-high transition. This feature
allows for an extremely fast startup because the peak
detectors never “catch” a false level created by a startup
transient. The peak detectors exhibit a fast-attack/slowdecay response.
Power-Supply Connections
The MAX7042 can be powered from a 2.4V to 3.6V
supply or a 4.5V to 5.5V supply. The device has an on-
14
MAX7042
DATA
SLICER
DATA
DS-
DS+
R
C
Figure 3. Generating Data-Slicer Threshold
MAX7042
PEAK
DET
DATA
SLICER
DATA
PEAK
DET
PDMAX
PDMIN
R
C
R
C
Figure 4. Generating Data-Slicer Threshold Using the Peak
Detectors
chip linear regulator that reduces the 5V supply to 3V
needed to operate the chip.
To operate the MAX7042 from a 3V supply, connect
DVDD, AVDD, and HVIN to the 3V supply. When using a
5V supply, connect the supply to HVIN only. In both
cases, bypass DVDD and HVIN with a 0.01µF capacitor
and AVDD with a 0.1µF capacitor. Place all bypass
capacitors as close to the respective supply pin as
possible.
______________________________________________________________________________________
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Typical Application Circuit
LNASEL
VDD
DATA
3.0V
FSEL2
FSEL1
VDD
C16
EN
5
EN
FSEL1
DVDD
XTAL2
DF
XTAL1
MAX7042
VDD
OP+
7
DS+
DS-
C1
PDMAX
9 10
11
12
C11
PDMIN
IFIN-
MIXOUT
AGND
MIXIN-
MIXIN+
EXPOSED PADDLE
C2
22
21
20
19
C4
R1
C5
18
17
IFIN+
LNAIN
LNAOUT
8
23
C3
C13
L1
24
AVDD
LNASRC
RF INPUT
VDD
C15
6
C7
26
DGND
Y1
C6
27
FSEL2
RSSI
28
HVIN
4
29
DATA
C14
30
LNASEL
31
15 16
13 14
C12
C8
L3
C9
VDD
IN
L2
GND
Y2
OUT
C10
______________________________________________________________________________________
15
MAX7042
have a dramatic effect on the effective inductance of a
passive component. For example, a 0.5in trace connecting a 100nH inductor adds an extra 10nH of inductance or 10%.
To reduce the parasitic inductance, use wider traces
and a solid ground or power plane below the signal
traces. Also, use low-inductance connections to ground
on all GND pins, and place decoupling capacitors
close to all VDD or HVIN connections.
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. On high-frequency inputs and
outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radiation. At high frequencies, trace lengths that are on the
order of λ/10 or longer act as antennas.
Keeping the traces short also reduces parasitic inductance. Generally, 1in of a PCB trace adds about 20nH
of parasitic inductance. The parasitic inductance can
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Table 3. Component Values for Typical Application Circuit
COMPONENT
VALUE FOR
315MHz RF
VALUE FOR
433.92MHz RF
C1
0.01µF
0.01µF
5%
C2
220pF
220pF
5%
C3
220pF
220pF
5%
C4
470pF
470pF
5%
C5
0.047µF
0.047µF
10%
DESCRIPTION
C6
0.1µF
0.1µF
10%
C7
100pF
100pF
10%
C8
100pF
100pF
10%
C9
1.2pF
Open
±0.1pF
C10
220pF
220pF
10%
C11
100pF
100pF
10%
C12
1500pF
1500pF
10%
C13
220pF
220pF
10%
C14
100pF
100pF
10%
C15
100pF
100pF
10%
C16
0.1µF
0.1µF
10%
L1
82nH
39nH
Coilcraft 0603CS
L2
30nH
16nH
Murata LQW18A
L3
3.9nH
Short
Coilcraft 0603CS
R1
100kΩ
100kΩ
5%
Y1
9.50939MHz
13.22563MHz
Crystal
Y2
10.7MHz ceramic filter
10.7MHz ceramic filter
Murata SFECV10.7 series
Chip Information
PROCESS: CMOS
16
______________________________________________________________________________________
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
QFN THIN.EPS
______________________________________________________________________________________
17
MAX7042
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
MAX7042
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
18
______________________________________________________________________________________
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
SSOP.EPS
36
E
DIM
A
A1
B
C
e
E
H
L
D
H
INCHES
MILLIMETERS
MAX
MIN
0.104
0.096
0.004
0.011
0.017
0.012
0.013
0.009
0.0315 BSC
0.299
0.291
0.398
0.414
0.040
0.020
0.598
0.612
MAX
MIN
2.65
2.44
0.29
0.10
0.44
0.30
0.23
0.32
0.80 BSC
7.40
7.60
10.11
10.51
0.51
15.20
1.02
15.55
1
TOP VIEW
D
A1
e
A
B
FRONT VIEW
C
0∞-8∞
L
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, 36L SSOP, 0.80 MM PITCH
APPROVAL
DOCUMENT CONTROL NO.
21-0040
REV.
E
1
1
Revision History
Pages changed at Rev 1: 1, 10, 11, 12, 15, 15, 17, 18, 19
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19
© 2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
MAX7042
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)