VISHAY TSOP1833XG1

TSOP18..XG1
Vishay Telefunken
Photo Modules for PCM Remote Control Systems
Available types for different carrier frequencies
Type
TSOP1830XG1
TSOP1836XG1
TSOP1838XG1
TSOP1856XG1
fo
30 kHz
36 kHz
38 kHz
56 kHz
Type
TSOP1833XG1
TSOP1837XG1
TSOP1840XG1
fo
33 kHz
36.7 kHz
40 kHz
Description
The TSOP18..XG1 – series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. The main benefit is the
reliable function even in disturbed ambient and the
protection against uncontrolled output pulses.
16 082
Features
D
D
D
D
D
Special Features
Photo detector and preamplifier in one package
Internal filter for PCM frequency
D Small size package
D Enhanced immunity against all kinds of
disturbance light
TTL and CMOS compatibility
D No occurrence of disturbance pulses at the
Output active low
output
Improved shielding against electrical field
disturbance
D Short settling time after power on (<200ms)
D Suitable burst length ≥6 cycles/burst
Block Diagram
3
Control
Circuit
Input
30 kW
1
PIN
AGC
Band
Pass
VS
OUT
Demodulator
2
GND
9612226
Document Number 82056
Rev. 4, 08-Jun-00
www.vishay.de • FaxBack +1-408-970-5600
1 (7)
TSOP18..XG1
Vishay Telefunken
Absolute Maximum Ratings
Tamb = 25_C
Parameter
Supply Voltage
Supply Current
Output Voltage
Output Current
Junction Temperature
Storage Temperature Range
Operating Temperature Range
Power Consumption
Soldering Temperature
Test Conditions
(Pin 3)
(Pin 3)
(Pin 1)
(Pin 1)
x
(Tamb
85 °C)
t
5s
x
Symbol
VS
IS
VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
Value
–0.3...6.0
5
–0.3...6.0
5
100
–25...+85
–25...+85
50
260
Unit
V
mA
V
mA
°C
°C
°C
mW
°C
Typ
1.2
1.3
Unit
mA
mA
V
m
Basic Characteristics
Tamb = 25_C
Parameter
Supply
y Current ((Pin 3))
Supply Voltage (Pin 3)
Transmission Distance
Output Voltage Low (Pin 1)
Irradiance (30 – 40 kHz)
Irradiance (56 kHz)
Irradiance
Directivity
Test Conditions
VS = 5 V, Ev = 0
VS = 5 V, Ev = 40 klx, sunlight
Ev = 0, test signal see fig.6,
IR diode TSAL6200, IF = 300 mA
IOSL = 0.5 mA,Ee = 0.7 mW/m2,
f = fo
Pulse width tolerance:
tpi – 4/fo < tpo < tpi + 6/fo,
test signal see fig.6
Angle of half transmission distance
Symbol
ISD
ISH
VS
d
Min
0.9
4.5
Max
1.5
5.5
35
VOSL
250
mV
Ee min
0.3
0.5
mW/m2
Ee min
0.4
0.7
mW/m2
Ee max
ϕ1/2
W/m2
deg
30
±45
Application Circuit
100
3
TSOP18..
m
4.7 F *)
W *)
+5V
W
>10 k
optional
TSAL62..
1
mC
2
GND
15905
www.vishay.de • FaxBack +1-408-970-5600
2 (7)
*) recommended to suppress power supply disturbances
Document Number 82056
Rev. 4, 08-Jun-00
TSOP18..XG1
Vishay Telefunken
Suitable Data Format
The circuit of the TSOP18..XG1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal ( not
suppressed) and disturbance signal (supressed) are
carrier frequency, burst length and Signal Gap Time
(see diagram below).
Some examples for suitable data format are:
NEC Code (repetitive pulse), NEC Code (repetitive
data), Toshiba Micom Format, Sharp Code, RC5
Code, RECS–80 Code, R–2000 Code.
The data signal should fullfill the following condition:
Some examples for such disturbance signals which
are suppressed by the TSOP18..XG1 are:
When a disturbance signal is applied to the
TSOP18..XG1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.
• Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).
• DC light (e.g. from tungsten bulb or sunlight),
• Burst length should be 6 cycles/burst or longer.
• After each burst a gap time of at least 9 cycles is
neccessary.
• Continuous signal at 38kHz or at any other
frequency,
• The data format should not make a continuous
signal transmission. There must be a Signal Gap Time
(longer than 15ms) at least each 90ms (see Figure A).
• Signals from fluorescent lamps (see Figure B).
• Continuous IR signal (e.g. 1ms burst, 2ms pause)
Signal Gap Time
0
10
20
30
40
50
60
70
80
90
100
time [ms]
Figure A: Data Signal (Output of IR Receiver) with a Signal Gap Time of 20ms
Signal Gap Time
0
2
4
6
8
10
12
14
16
18
20
time [ms]
Figure B: Disturbance Signal from Fluorescent Lamp with Signal Gap Time of 7ms (suppressed by TSOP18..)
Document Number 82056
Rev. 4, 08-Jun-00
www.vishay.de • FaxBack +1-408-970-5600
3 (7)
TSOP18..XG1
Vishay Telefunken
Typical Characteristics (Tamb = 25_C unless otherwise specified)
100.0
E e min – Threshold Irradiance (mW/m2 )
eE
min
/eE – Rel. Responsitivity
1.0
0.8
0.6
0.4
0.2
f = f0
"5%
Df ( 3 dB ) = f0 / 7
0.0
0.7
0.8
0.9
1.0
1.1
3.5
^
^
Correlation with ambient light sources
( Disturbance effect ) : 1 0W/m2 1.4 klx
( Stand.illum.A, T = 2855 K ) 8.2 klx
( Daylight, T = 5900 K )
3.0
2.5
2.0
Ambient, l = 950 nm
1.5
1.0
0.5
0
0.01
0.10
1.00
10.00
100.00
E – DC Irradiance (W/m2)
96 12214
100 Hz
0.1
0.1
1.0
10.0
100.0
1000.0
DVs RMS – AC Voltage on DC Supply Voltage (mV)
1.0
0.9
0.8
Sensitivity in dark ambient
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
VS – Supply Voltage ( V )
14312
Figure 2. Sensitivity in Bright Ambient
Figure 5. Sensitivity vs. Supply Voltage
Ee
Ee min – Threshold Irradiance ( mW/m2 )
1.0
Figure 4. Sensitivity vs. Supply Voltage Disturbances
E e min – Threshold Irradiance (mW/m2 )
E e min – Threshold Irradiance (mW/m2 )
4.5
10 kHz
1 kHz
96 12215
Figure 1. Frequency Dependence of Responsivity
4.0
10.0
1.3
1.2
f / f0 – Relative Frequency
94 9102
f = fo
Optical Test Signal
2.0
f ( E ) = f0
1.6
600 ms
600 ms
1.2
t
TD*
Trep=100 ms
* Trep–TD > 15 ms is recommended for optimal function
0.8
VO
0.4
Output Signal, ( see Fig.7 )
9612218
VOH
0.0
0.0
94 8147
0.4
0.8
1.2
1.6
2.0
E – Field Strength of Disturbance ( kV / m )
Figure 3. Sensitivity vs. Electric Field Disturbances
www.vishay.de • FaxBack +1-408-970-5600
4 (7)
VOL
Ton
Toff
t
Figure 6. Output Function
Document Number 82056
Rev. 4, 08-Jun-00
TSOP18..XG1
Vishay Telefunken
0.75
0.70
Toff
0.65
0.60
Ton
0.55
0.50
0.45
0.4
0.1
optical test signal, fig.6
1.0
10.0
100.0 1000.0 10000.0100000.0
Ee – Irradiance (mW/m2)
16163
Figure 10. Supply Current vs. Supply Voltage
S ( l ) rel – Relative Spectral Sensitivity
2.0
1.8
Vs = 5 V
I s – Supply Current ( mA )
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
–30 –15
0
15
30
45
60
75
1.2
1.0
0.8
0.6
0.4
0.2
0
750
90
Tamb – Ambient Temperature ( °C )
14315
VS – Supply Voltage ( V )
14317
Figure 7. Output Pulse Diagram
850
950
1150
1050
l – Wavelength ( nm )
94 8408
Figure 8. Supply Current vs. Ambient Temperature
E e min – Threshold Irradiance (mW/m2 )
1.7
1.6
Supply current in dark ambient
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
I s – Supply Current ( mA )
T on ,Toff – Output Pulse Length (ms)
0.80
Figure 11. Relative Spectral Sensitivity vs. Wavelength
0°
1.0
10°
20°
30°
0.9
0.8
Sensitivity in dark ambient
0.7
40°
0.6
1.0
0.5
0.9
50°
0.8
60°
0.4
0.3
0.2
70°
0.7
80°
0.1
0
–30 –15
96 12221
0
15
30
45
60
75
90
Tamb – Ambient Temperature ( °C )
Figure 9. Sensitivity vs. Ambient Temperature
Document Number 82056
Rev. 4, 08-Jun-00
0.6
96 12223p2
0.6
0.4
0.2
0
0.2
0.4
drel – Relative Transmission Distance
Figure 12. Directivity tsop
www.vishay.de • FaxBack +1-408-970-5600
5 (7)
TSOP18..XG1
Vishay Telefunken
Dimensions in mm
14273
www.vishay.de • FaxBack +1-408-970-5600
6 (7)
Document Number 82056
Rev. 4, 08-Jun-00
TSOP18..XG1
Vishay Telefunken
Ozone Depleting Substances Policy Statement
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating
systems with respect to their impact on the health and safety of our employees and the public, as well as their
impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as
ozone depleting substances ( ODSs ).
The Montreal Protocol ( 1987 ) and its London Amendments ( 1990 ) intend to severely restrict the use of ODSs and
forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban
on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of
ODSs listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively
2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency ( EPA ) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting
substances and do not contain such substances.
We reserve the right to make changes to improve technical design and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application
by the customer. Should the buyer use Vishay-Telefunken products for any unintended or unauthorized application, the
buyer shall indemnify Vishay-Telefunken against all claims, costs, damages, and expenses, arising out of, directly or
indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423
Document Number 82056
Rev. 4, 08-Jun-00
www.vishay.de • FaxBack +1-408-970-5600
7 (7)