EPCOS B43415C6108A000

Aluminum electrolytic capacitors
Capacitors for pulse applications
Series/Type:
B43415, B43416
Date:
November 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Capacitors for pulse applications
B43415, B43416
Compact up to 60 °C
Application
Professional flash light generators
Features
Compact design
Outstanding reliability
High charge/discharge proof, polar
Low leakage current
Low dissipation factor
RoHS-compatible
B43415
Construction
Aluminum case, fully insulated
Safety vent
B43416
Terminals
Snap-in
Solder lug
Overview
Temperature
°C
+60
(max. case temp.)
Series
Useful life
B43415
Solder lug
B43416
Snap-in
> 50000
discharges
Please read Cautions and warnings and
Important notes at the end of this document.
VR
V DC
300 ... 500
CR
µF
1000 ... 6600
200 ... 1500
Page 2 of 16
B43415, B43416
Compact up to 60 °C
Specifications and characteristics in brief
Rated voltage
Rated capacitance
Capacitance
tolerance
Leakage current
(5 min, 20 °C)
VR
CR
∆CR
Dissipation factor
Useful life
tan δ
300 ... 500 V DC
200 ... 6600 µF
10/+20%
Ileak
Vibration resistance test
IEC climatic category
15%
> 50000 discharges at:
Requirements:
Case temperature
≤ 60 °C ∆C/C ≤ ±20% of initial value
Discharge repetition
≥2s
ESR ≤ 3 times initial specified
rate
limit
Max. discharges per
≤ 5000
Ileak
≤ initial specified limit
week
Charge resistance
>10 Ω
Discharge resistance >0.5 Ω
To IEC 60068-2-6, test Fc:
Displacement amplitude 0.35 mm, frequency range 10 Hz ... 55 Hz,
acceleration max. 5 g, duration 3 × 2 h.
Capacitor mounted by its body which is rigidly clamped to the work
surface.
If terminals are used for mechanical fixation of the capacitor, the
vibration resistance can be reduced depending on capacitor size.
VR ≤ 400 V DC: 40/060/56 (40 °C/+60 °C/56 days damp heat test)
VR > 400 V DC: 25/060/56 (25 °C/+60 °C/56 days damp heat test)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 16
B43415
Compact up to 60°C
Dimensional drawing
B43415, solder lug terminals
Dimensions, weights and packing units
d×l
mm
35 × 55
35 × 65
40 × 65
40 × 70
40 × 80
40 × 90
40 × 105
40 × 110
50 × 80
50 × 100
Lead
spacing (LS)
mm
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
20.0
20.0
Approx.
weight
g
75
88
115
130
150
160
180
190
230
270
Please read Cautions and warnings and
Important notes at the end of this document.
Packing
units
pcs.
59
59
42
42
42
42
42
42
28
28
Page 4 of 16
B43415
Compact up to 60°C
Technical data and ordering codes B43415
CR
100 Hz
20 °C
µF
Case dimensions
d × l
mm
VR = 300 V DC
2100
35 × 65
3000
40 × 70
4700
40 × 105
6600
50 × 100
VR = 330 V DC
2100
40 × 65
3000
40 × 80
3800
40 × 105
5600
50 × 100
VR = 360 V DC
2100
40 × 65
3000
40 × 90
3800
40 × 110
4900
50 × 100
VR = 400 V DC
1000
35 × 55
2100
40 × 80
3000
40 × 110
3800
50 × 100
VR = 500 V DC
1000
40 × 65
2100
50 × 80
2500
50 × 100
Please read Cautions and warnings and
Important notes at the end of this document.
Ileak,max
5 min.
20 °C
mA
Ordering code
3.4
4.4
6.0
7.7
B43415C3218A000
B43415C3308A000
B43415C3478A000
B43415C3668A000
3.7
4.7
5.6
7.3
B43415C8218A000
B43415C8308A000
B43415C8388A000
B43415C8568A000
3.9
5.0
5.9
7.6
B43415C9218A000
B43415C9308A000
B43415C9388A000
B43415C9498A000
2.5
4.2
5.4
6.4
B43415C9108A000
B43415D9218A000
B43415D9308A000
B43415D9388A000
2.9
4.9
5.8
B43415C6108A000
B43415C6218A000
B43415C6258A000
Page 5 of 16
B43416
Compact up to 60°C
Dimensional drawing
B43416, snap-in terminals
Dimensions, weights and packing units
d×l
mm
25 × 45
30 × 40
30 × 50
35 × 45
35 × 50
35 x 55
Approx.
weight
g
25
36
46
56
70
81
Please read Cautions and warnings and
Important notes at the end of this document.
Packing
units
pcs.
130
80
80
60
60
60
Page 6 of 16
B43416
Compact up to 60°C
Technical data and ordering codes B43416
CR
100 Hz
20 °C
µF
Case dimensions
d×l
mm
VR = 300 V DC
1000
30 × 50
1500
35 × 50
VR = 330 V DC
1000
35 × 45
1200
35 × 50
VR = 360 V DC
560
30 × 40
1100
35 × 50
1200
35 × 55
VR = 400 V DC
330
25 × 45
700
35 × 45
900
35 × 55
VR = 500 V DC
200
25 × 45
560
35 × 50
600
35 × 55
Please read Cautions and warnings and
Important notes at the end of this document.
Ileak,max
5 min.
20 °C
mA
Ordering code
2.0
2.7
B43416C3108A000
B43416C3158A000
2.2
2.5
B43416C8108A000
B43416C8128A000
1.5
2.6
2.8
B43416C9567A000
B43416C9118A000
B43416C9128A000
1.2
2.0
2.6
B43416C9337A000
B43416C9707A000
B43416C9907A000
0.9
2.0
2.1
B43416C6207A000
B43416C6567A000
B43416C6607A000
Page 7 of 16
B43415, B43416
Compact up to 60 °C
Packing of snap-in capacitors
Packing of solder lug capacitors
For ecological reasons the packing is pure cardboard.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 16
B43415, B43416
Compact up to 60 °C
AC capacitance versus temperature
VR = 350 V DC
Typical behaviour
Dissipation factor tan δ versus temperature
VR = 350 V DC, measuring frequency = 120 Hz
Typical behaviour
Leakage current Ileak versus temperature
Measurement duration = 5 minutes
Typical behaviour
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 16
B43415, B43416
Compact up to 60 °C
Questionnaire
Please use the questionnaire when having other, improved or additional technical requirements
which cannot be covered by our standard series.
The characteristic data listed in the questionnaire below are essentially the most important
information for determining design dimensions of electrolytic capacitors for professional
photo flash applications.
µF
Rated capacitance per capacitor
Rated voltage per capacitor
V DC
Charge/discharge voltage
/
Required dimensions: Diameter (max.)
V
mm
Length (max.)
mm
Style of terminals
°C
Ambient temperature
Method of cooling
Discharge conditions
Internal resistance of the discharge tube (if applicable)
Ω
Charging resistance (series resistance)
Ω
No. of capacitors in series
No. of capacitors in parallel
Flash sequence
Pause periods
Other special operating conditions
Expected useful life
flashes
Annual demand of capacitors
For any further support, please contact your nearest EPCOS representative.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 16
B43415, B43416
Compact up to 60 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 16
B43415, B43416
Compact up to 60 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Polarity
Make sure that polar capacitors are connected
with the right polarity.
Reverse voltage
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1
"Mounting positions of
capacitors with screw
terminals"
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 16
B43415, B43416
Compact up to 60 °C
Topic
Soldering,
cleaning agents
Passive
flammability
Active
flammability
Safety information
Reference
Chapter "General
technical information"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Avoid external energy, such as fire or electricity.
8.1
"Passive flammability"
Avoid overload of the capacitors.
8.2
"Active flammability"
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 16
Reference
Chapter "Capacitors
with screw terminals"
"Screw terminals accessories"
B43415, B43416
Compact up to 60 °C
Symbols and terms
Symbol
English
German
C
CR
CS
CS,T
Cf
d
dmax
ESL
ESR
ESRf
Capacitance
Rated capacitance
Series capacitance
Series capacitance at temperature T
Capacitance at frequency f
Case diameter, nominal dimension
Maximum case diameter
Self-inductance
Equivalent series resistance
Equivalent series resistance at
frequency f
Equivalent series resistance at
temperature T
Frequency
Current
Alternating current (ripple current)
Root-mean-square value of alternating
current
Ripple current at frequency f
Maximum permissible ripple current
Rated ripple current
Rated ripple current for base cooling
Leakage current
Operating leakage current
Case length, nominal dimension
Maximum case length (without
terminals and mounting stud)
Resistance
Insulation resistance
Balancing resistance
Temperature
Temperature difference
Ambient temperature
Case temperature
Capacitor base temperature
Time
Period
Service life (operating hours)
Kapazität
Nennkapazität
Serienkapazität
Serienkapazität bei Temperatur T
Kapazität bei Frequenz f
Gehäusedurchmesser, Nennmaß
Maximaler Gehäusedurchmesser
Eigeninduktivität
Ersatzserienwiderstand
Ersatzserienwiderstand bei Frequenz f
ESRT
f
I
IAC
IAC,rms
IAC,f
IAC,max
IAC,R
IAC,R (B)
Ileak
Ileak,op
l
lmax
R
Rins
Rsymm
T
∆T
TA
TC
TB
t
∆t
tb
Please read Cautions and warnings and
Important notes at the end of this document.
Ersatzserienwiderstand bei Temperatur T
Frequenz
Strom
Wechselstrom
Wechselstrom, Effektivwert
Wechselstrom bei Frequenz f
Maximal zulässiger Wechselstrom
Nennwechselstrom
Nennwechselstromstrom für Bodenkühlung
Ableitstrom
Ableitstrom bei Betrieb
Gehäuselänge, Nennmaß
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
Widerstand
Isolationswiderstand
Symmetrierwiderstand
Temperatur
Temperaturdifferenz
Umgebungstemperatur
Gehäusetemperatur
Temperatur des Becherbodens
Zeit
Zeitraum
Brauchbarkeitsdauer (Betriebszeit)
Page 14 of 16
B43415, B43416
Compact up to 60 °C
Symbol
V
VF
Vop
VR
VS
XC
XL
Z
ZT
tan δ
λ
ε0
εr
ω
English
Voltage
Forming voltage
Operating voltage
Rated voltage, DC voltage
Surge voltage
Capacitive reactance
Inductive reactance
Impedance
Impedance at temperature T
Dissipation factor
Failure rate
Absolute permittivity
Relative permittivity
Angular velocity; 2 π f
German
Spannung
Formierspannung
Betriebsspannung
Nennspannung, Gleichspannung
Spitzenspannung
Kapazitiver Blindwiderstand
Induktiver Blindwiderstand
Scheinwiderstand
Scheinwiderstand bei Temperatur T
Verlustfaktor
Ausfallrate
Elektrische Feldkonstante
Dielektrizitätszahl
Kreisfrequenz; 2 π f
Notes
All dimensions are given in mm.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 16
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
Page 16 of 16