PHILIPS CX24118A-12Z

CX24118A
Advanced Modulation Digital Satellite Tuner
Rev. 02 — 8 September 2009
Document information
Info
Keywords
Abstract
Content
Product data sheet
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
Ordering information
Type number
Description
CX24118A-12Z*
Advanced Modulation Digital Satellite Tuner
Package
36-pin QFN
*Lead-free (Pb Free) and RoHS compliant
Revision history
Revision
Date
Description
02
20090908
Added Figure 12
01
20081125
First NXP version based on the Conexant 102322A data sheet.
Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
2
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
General description
The CX24118A is a direct down-conversion satellite tuner intended for high-volume digital
video, audio, and data receivers. The CX24118A offers excellent phase noise performance
and very low implementation loss, required for advanced modulation systems such as 8PSK
and DVB-S2.
The CX24118A has a built-in auto-tuning system that eliminates the need for software
calibration. The on-chip fractional synthesizer enables fine frequency step size without
adversely affecting lock time. The CX24118A does not require a balun, thus reducing
external BOM cost. Its highly integrated design saves valuable board space and simplifies
RF layout.
Features
‹
‹
‹
‹
‹
‹
‹
‹
Single-chip RF-to-baseband satellite receiver
Zero-IF architecture eliminates the need for image reject filtering
Very low phase noise integrated Local Oscillators (LOs) for 8PSK and DVB-S2
applications
Variable baseband filters for optimal interference rejection
Auto-tuning system eliminates need for software calibration
Very low power consumption
Small (6 mm x 6 mm) footprint
Lead-free package
Applications
‹
‹
8PSK, DVB-S2, and advanced modulation set-top boxes
Commercial digital video, audio, and PVR receivers
Product Specifications
‹
‹
‹
‹
RF input: 925–2175 MHz
Symbol rate: 1–45 MSps
Noise figure: 10 dB, typical
Input IP3 at minimum gain: 10 dBm, typical
Block diagram
PLL and VCO
DC Offset
Cancellation
I/Q
Mixer
Filter 1
VGA1
Filter 2
: 2,
:4
CP_OUT
VTUNE
VGA2
I_OUT
VCA
0o
RF_IN
Final
Amplifier
90o
Q_OUT
AGC
Control
AGC
XSEL
XTAL1
XTAL2
CKREF_OUT
DC Offset
Cancellation
Crystal Oscillator
and
Clock Control
CX24118A_N_2
Product data sheet
Filter
Control
Logic
Interface
SDA
SCL
SADD
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
3
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
4
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
1
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1
Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Functional Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Downconverter and Baseband Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Gain Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4
Local Oscillator and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5
Crystal Oscillator and Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6
Automatic Tuning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.1
Auto-tuning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Serial Programming Interface and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Serial Programming Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Register Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Register Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Application Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Thermal Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Sleep Mode Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
Changing from Normal Operation to Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2
Changing from Sleep Mode to Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Electrical, Thermal, and Mechanical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
S11 Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
Electrical and Thermal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.2
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.3
Receiver Electrical and Thermal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CX24118A_N_2
Product data sheet
11
11
12
15
15
15
16
17
18
20
20
23
23
26
27
29
37
37
37
37
37
39
39
40
40
40
40
43
45
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
5
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
6
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detailed Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Divider Settings vs. Frequency When Using 40 MHz Crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Third-Overtone Crystal Oscillator External Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Clock and Data Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Single-Byte Write Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Multiple-Bytes Write Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Single-Byte Read Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Multiple-Bytes Read Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S11 Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CX24118A_N_2
Product data sheet
11
15
18
19
23
24
24
25
26
39
43
44
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
7
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
8
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Signal Level Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum Signal Level Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Component Values for Third-Overtone Crystal Oscillator External Circuit . . . . . . . . . . . . . . . .
Crystal Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Bit Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CX24118A_N_2
Product data sheet
12
16
17
19
20
26
27
37
40
40
40
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
9
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
10
CX24118A
Chapter 1: Pin Descriptions
Rev. 02 — 8 September 2009
1.1
Product data sheet
Pin Diagram
Figure 1 provides a pinout of the CX24118A.
VCC_PS
XSEL
SADD
N/C
N/C
VCC2_RF
N/C
N/C
N/C
35
34
33
32
31
30
29
28
Pin Diagram
36
Figure 1.
N/C
1
27
N/C
VCC_VCO
2
26
RF_INN
VTUNE
3
25
RF_INP
VCC_CP
4
24
VCC1_RF
23
VCC1_BB
CP_OUT
CX24118A
5
(Exposed Paddle = Gnd)
17
18
Q_OUTN
N/C
Q_OUTP
19
16
9
I_OUTP
XTAL2
15
BB_REF
I_OUTN
20
14
8
SCL
XTAL1
13
VCC2_BB
SDA
21
12
7
GND_DIG
VCC_XTAL
11
AGC
VCC_DIG
22
10
6
CKREF_OUT
XTAL_BIAS
102322_002
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
11
CX24118A
NXP Semiconductors
Chapter 1: Pin Descriptions
1.2
Pin Assignments
Table 1 lists the CX24118A pin names, numbers, types, and descriptions.
Table 1.
Pin Assignments
Pin Name
Pin Number
Type
Description
N/C
1
N/C
VCC_VCO
2
Power
3.3V power supply for the VCO section.
VTUNE
3
Input
VCO tuning voltage input. The output of the external PLL loop filter is connected to this
pin.
VCC_CP
4
Power
3.3V power supply for the charge pump section.
CP_OUT
5
Output
Charge pump output. The input of the external PLL loop filter is connected to this pin.
XTAL_BIAS
6
Input
Crystal oscillator bias. For normal operation, leave this pin unconnected.
VCC_XTAL
7
Power
3.3V power supply for the crystal oscillator section.
XTAL1
8
Input
XTAL2
9
Output
Crystal oscillator input pins. Use a 40 MHz or 40.444 MHz third-overtone crystal
oscillator circuit.
CKREF_OUT
10
Output
Clock reference output. The maximum load allowed at this pin is 10 kΩ // 20 pF.
VCC_DIG
11
Power
3.3 V power supply for digital section.
GND_DIG
12
Ground
Digital ground.
SDA
13
I/O
SCL
14
Input
I_OUTN
15
Output
The negative differential I channel output to demodulator. Zout = 1 kΩ // 10 pF.
I_OUTP
16
Output
The positive differential I channel output to demodulator. Zout = 1 kΩ // 10 pF.
Q_OUTP
17
Output
The positive differential Q channel output to demodulator. Zout = 1 kΩ // 10 pF.
Q_OUTN
18
Output
The negative differential Q channel output to demodulator. Zout = 1 kΩ // 10 pF.
N/C
19
N/C
Not internally connected.
BB_REF
20
Input
Current reference for baseband section. Place a 698 Ω ±1% resistor to ground.
VCC2_BB
21
Power
3.3 V power supply for the baseband section.
AGC
22
Input
AGC control input from the demodulator, which controls the gain of the RF attenuator
and both baseband variable gain amplifiers. Zin = 10 kΩ // 20 pF.
VCC1_BB
23
Power
3.3 V power supply for the baseband section.
VCC1_RF
24
Power
3.3 V power supply pin for the RF section.
RF_INP
25
Input
The positive differential RF signal input pin.
Not internally connected.
Serial programming interface data signal. Open drain.
Serial programming interface clock signal.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
12
CX24118A
NXP Semiconductors
Chapter 1: Pin Descriptions
Table 1.
Pin Assignments
Pin Name
Pin Number
Type
RF_INN
26
Input
The negative differential RF signal input pin. This pin should be AC grounded with a
capacitor to ground.
N/C
27
N/C
Not internally connected.
N/C
28
N/C
Not internally connected.
N/C
29
N/C
Not internally connected.
N/C
30
N/C
Not internally connected.
VCC2_RF
31
Power
N/C
32
N/C
Not internally connected.
N/C
33
N/C
Not internally connected.
SADD
34
I/O
Serial address select pin. This pin has an internal pull-up, so an open on this pin will be
a logic level high (default address of 54) and a short to ground will be a logic level low
(address of 14).
XSEL
35
Input
Crystal bias select pin. Leave floating for operation with a 40 MHz third-overtone
crystal. This pin has an internal 30 kΩ pull-up resistor.
VCC_PS
36
Power
3.3 V power supply for the prescaler section.
Ground
The exposed paddle at the bottom of the chip is the common chip ground and the
thermal conductor.
Exposed Paddle
Description
3.3 V power supply pin for the RF section.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
13
CX24118A
NXP Semiconductors
Chapter 1: Pin Descriptions
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
14
CX24118A
Chapter 2: Functional Descriptions
Rev. 02 — 8 September 2009
2.1
Product data sheet
General Description
The CX24118A is a highly integrated direct conversion tuner requiring a minimum of off-chip
components. It incorporates a low-noise amplifier with integrated Voltage Controlled
Attenuator (VCA), quadrature down converter, variable bandwidth base-band filter/amplifier,
fractional synthesizer, crystal oscillator with buffered output, and an automatic tuning system.
The chip is controlled through a multi-byte read/write enabled I2C®-compatible interface.
A CX24118A detailed block diagram is shown in Figure 2.
Figure 2.
Detailed Block Diagram
DC Offset
Cancellation
I/Q
Mixer Filter 1
VGA1 Filter 2 VGA2
I_OUT
Final Amplifier
VCA
0o
RF_IN
90o
Q_OUT
AGC
Control
DC Offset
Cancellation
AGC
Filter
Control
: 2,
:4
LODivSel
XSEL
XTAL1
XTAL2
:2
1
Charge
Pump
PFD
0
CP_OUT
VCO
Sine Wave
0
CKREF_OUT
1
PLLRefDiv
Prescaler
18 Bit
DSM
Square Wave
:2
VTUNE
Logic
Interface
SDA
SCL
SADD
OUTRefDiv
102322_007
2.2
Downconverter and Baseband Filtering
The L band input from the LNB is fed into the CX24118A either differentially or single-ended.
The input signal goes through a low-noise amplification block and is downconverted to a
baseband frequency by quadrature downconversion. The output of the downconverter is
band limited by a variable bandwidth filter that can be set to 35, 40, 65, or 100 MHz. A
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
15
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
variable gain baseband amplifier section provides further amplification. The baseband
section includes a servo loop, which eliminates DC offset variations at the output. The
baseband amplifier section also includes a filter with finer bandwidth control between 2 MHz
and 65 MHz. The filter is optimized to provide stop band attenuation for anti-alias filtering and
adjacent channel performance.
2.3
Gain Settings
The CX24118A is controlled by a single AGC signal, providing a dynamic range of 90 dB.
The gain stages include an LNA (Low Noise Amplifier) and VCA (Voltage Controlled
Attenuator), VGA1 (Variable Gain Amplifier 1), VGA2, and a final amplifier. These gain
stages are shown in figure 2-1.
The gain and offset of the different stages can be adjusted to provide the best overall IP3 and
Noise Figure performance over input power. To optimize the performance at both high and
low powers, split gain settings are recommended. This involves estimating the input power in
order to select the best set of gain settings. The maximum signal level settings given in
Table 2 should be used when the input power is high while there is significant power from
other carriers within the satellite frequency range. The minimum signal level settings given in
Table 3 should be used when the input power is low or when significant power from other
carriers within the satellite frequency range does not exist. The transition point between the
minimum signal level settings and the maximum signal level settings is set at Pthreshold = -50
dBm.
Table 2.
Maximum Signal Level Settings
Parameter
Register Location
Register Setting
Meaning
RFVCAOff[1:0]
0x20[3:2]
00b
-70 dB
BBVGA2Off[2:0]
0x1F[5:3]
111b
-27 dB
BBVGA1Off[2:0]
0x1F[2:0]
111b
-22 dB
BBAmpGain[3:0]
0x1D[3:0]
0011b
31 dB(1)
FOOTNOTES:
(1) This value is valid for the CX24116, CX24126, and CX24114 demodulators. For the CX24123
demodulator, use the setting that corresponds to 25 dB.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
16
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
Table 3.
Minimum Signal Level Settings
Parameter
Register Location
Register Setting
Meaning
RFVCAOff[1:0]
0x20[3:2]
10b
-64 dB
BBVGA2Off[2:0]
0x1F[5:3]
011b
-29 dB
BBVGA1Off[2:0]
0x1F[2:0]
010b
-32 dB
BBAmpGain[3:0]
0x1D[3:0]
0011b
31 dB(1)
FOOTNOTES:
(1) This value is valid for the CX24116, CX24126, and CX24114 demodulators. For the CX24123
demodulator, use the setting that corresponds to 25 dB.
2.4
Local Oscillator and PLL
A bank of six Voltage Controlled Oscillators (VCOs) cover the entire 925 MHz to 2175 MHz
range for downconversion with adequate overlap between VCOs. Each VCO has two bands
of operation, high and low, resulting in a total of 12 virtual VCOs. All the VCOs are integrated
into the chip, eliminating the need for external varactor diodes. The automatic tuning system
selects the appropriate VCO to generate the Local Oscillator (LO), eliminating the need for
calibration during initialization or channel change. The VCOs can also be selected manually,
overriding the automatic tuning system. For more information on the automatic tuning
system, see Section 2.6
The on-chip fractional synthesizer generates the LO with a very fine step size. The fractional
synthesizer consists of a 9-bit integer divider and an 18-bit sigma delta modulator with an 8level quantizer. The sigma delta modulator dithers the fractional division ratio to convert
spurious tones and quantization noise to white noise. The charge pump current selection is
based on the VCO tuning voltage, i.e., VCO output frequency. The charge pump tuning
system uses four tuning voltage ranges, and the charge pump current level for each range is
set automatically at every channel change to give optimum integrated phase noise.
The values to be programmed into the PLL’s integer and fractional divider registers are
computed as follows:
1. Set the dividers LODivSel (0x18[6]) and PLLRefDiv (0x02[1]) based on pre-defined or
calculated frequency ranges.
• See Figure 3 for recommended divider settings when using a 40 MHz crystal.
2. Calculate the total PLL division ratio.
F
×1
F xtal × 2
VCO
- ; if PLLRefDiv = 0
Ndivider = ---------------------
F
×2
F xtal × 2
VCO
- ; if PLLRefDiv = 1
= ---------------------
3. Calculate the integer divider PLLIntDiv[8:0].
PLLIntDiv[8:0] = Round[Ndivider] – 32
• The Round function rounds the result to the nearest integer.
• PLLIntDiv[8:0] can range from 6d to 511d. This is taken into consideration when
selecting the divider ranges.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
17
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
4. Calculate the fractional divider PLLFracDiv[17:0].
PLLFracDiv[17:0] = Round [218 x (Ndivider - PLLIntDiv[8:0] - 32)]
• To avoid fractional spurs, the fractional divider should not produce VCO
frequencies within 250 kHz or 125 kHz of the frequencies generated by
PLLFracDiv[17:0] = 0.0 or 0.5 respectively.
• When the requested frequency is within 250 kHz of the frequency generated by
PLLFracDiv[17:0] = 0.0, the PLL should be put into integer mode. Integer mode is
enabled by setting register bit DSMByp (0x10[6]) to 1.
• When the requested frequency is within 125 kHz of the frequency generated by
PLLFracDiv[17:0] = 0.5, the closest fractional value outside of the keep-out range
should be used.
Figure 3.
Recommended Divider Settings vs. Frequency When Using 40 MHz Crystal
÷4
LODivSel (1)
Divider ratio
÷2
÷2
PLLRefDiv (2)
÷1
925
1165
f (MHz)
1500 (3)
2175
REN_003
(1)
The LO divider is changed to ÷4 below 1165 MHz in order to keep the VCO frequency out of the input frequency range of 925
to 2175 MHz.
(2) The PLL frequency divider is changed across the frequency band to optimize phase noise while keeping the value of
PLLInDiv[8:0] within its usable range of 65-511d.
(3) This reference divider break-point is set at 37.5*Fxtal. For a 40 MHz Xtal, this value is 1500 MHz.
2.5
Crystal Oscillator and Reference Clock
The crystal oscillator should be used with a 40 MHz or 40.444 MHz third-overtone crystal. It
generates the reference frequency for the fractional synthesizer and provides the clock for
the rest of the system. It is also divided and buffered to produce an external clock that can be
used as a clock signal for the demodulator. Register bit OutRefDiv (0x02[2]) sets the
frequency of the reference clock output at pin CKREF_OUT so that when OUTRefDiv = 0, a
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
18
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
40 MHz sinusoidal clock is produced, and when OUTRefDiv = 1, a 20 MHz square clock is
produced (when OUTRefDiv = 1 mode is used, the XTAL_BIAS pin needs to be grounded).
The third overtone crystal requires external circuitry to load the crystal properly at the thirdovertone frequency while suppressing the fundamental frequency. This circuit is shown in
Figure 4, and the recommended component values are listed in Table 4. The external
components should be RF type components (high Q) with good characteristics at 40 MHz.
Figure 4.
Third-Overtone Crystal Oscillator External Circuit
OUTRefDiv
To System
CX24118A
:2
1
6
CKREF_OUT
XSEL
XTAL_BIAS
0
XTAL2
9
XTAL1
8
35
To Demodulator
C3
C2
C1
L1
102322_014
Table 4.
Recommended Component Values for Third-Overtone Crystal Oscillator
External Circuit
Component
Value
C1
22 pF
C2
56 pF
C3
1 nF
L1
390 nH
The selected crystal should be a high-quality crystal with minimum drive level dependencies.
Table 5 lists the required crystal characteristics. Component tolerances should be 5 percent
or better.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
19
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
Table 5.
Crystal Requirements
Parameter
Specification
Frequency
40.000 MHz (40.444 MHz(3))
Mode
Parallel resonant, 3rd overtone
Frequency tolerance at 25 ºC
25 ppm
Frequency tolerance over
temperature
50 ppm
Maximum equivalent series
resistance (ESR) (1)
80
Aging
5 ppm/Year
Load Capacitance
18 pF
Maximum Drive Level(2)
1 mW
Operating Temperature Range
0 ºC to 70 ºC
FOOTNOTES:
(1) This is the maximum crystal series resistance for reliable startup at low energy levels. Compliance with
this spec at 10 nW is required. This number is also required at operating power levels.
(2) The power dissipated across the crystal will depend on the ESR of the crystal and the bias level of the
oscillator. Leaving the XTAL_BIAS pin open will create a lower bias current than if it were shorted to
ground.
(3) A 40.444 MHz crystal is only needed when DVB symbol rates of 44–45 MSps are required for the
CX24116 DVB-S2 demodulator.
2.6
Automatic Tuning System
The CX24118A uses an automatic tuning system to select the VCO and band during channel
change. The system selects among the 12 virtual VCOs (VCO1–VCO6, each with a high and
low band) based on preload values that are programmed during initialization. The automatic
tuning system does not require time-consuming calibration during initialization or channel
change. The procedure for using the automatic tuning system is given in Section 2.6.1.
2.6.1
Auto-tuning Procedure
During Initialization
1. Program the tuning system preload values with the values provided by Conexant and
enable the automatic tuning system.
a. Set register field TUN1[5:0] (0x14[5:0]) to 0x0F.
– Register 0x14 also contains the tuning system enable bits, TUNAutoEn[1:0], which
should be programmed to 00b at the same time.
b. Set register TUN2[7:0] (0x15[7:0]) to 0xFF.
c. Set register TUN3[7:0] (0x16[7:0]) to 0xFF.
d. Set register TUN4[7:0] (0x17[7:0]) to 0xF0.
2. Program automatic charge pump levels with the values provided by Conexant. These
values are selected based on the VCO tuning voltage.
a. Set register field CPLevel1[1:0] (0x11[7:6]) to 11b.
b. Set register field CPLevel2[1:0] (0x11[5:4]) to 11b.
c. Set register field CPLevel3[1:0] (0x11[3:2]) to 10b.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
20
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
d. Set register field CPLevel4[1:0] (0x11[1:0]) to 00b.
3. There are other registers not directly related to tuning system initialization that must also
be programmed. These values are not discussed here.
During Channel Change
1. Choose the appropriate dividers using register bits LODivSel (0x18[6]) and PLLRefDiv
(0x02[1])). For more detail, see Section 2.4
2. Select the gain settings. The minimum signal level settings can be used at this point.
3. Set the bandwidths of the baseband filters using register fields BBFil1BW[1:0] and
BBFil2BW[1:0] based on the symbol rate, roll-off, and desired carrier acquisition range.
4. Program the PLL dividers PLLIntDiv[8:0] and PLLFracDiv[17:0] using the values
generated from the procedure given in Section 2.4, and start the tuning process as
follows:
a. Program registers 0x19-0x1B.
b. Program the remaining PLL dividers into register 0x1C while setting the start bit
TUNReset (0x1C[4]) to 1.
5. Monitor PLL lock using register bit TUNLD. When lock has been achieved, measure the
power to determine the appropriate gain settings. Set new gain settings if required. See
Section 2.3 for more detail.
a. After lock, the charge pump values are automatically selected, based on the VCO
tuning voltage and the charge pump initialization values.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
21
CX24118A
NXP Semiconductors
Chapter 2: Functional Descriptions
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
22
CX24118A
Chapter 3: Serial Programming Interface and Registers
Rev. 02 — 8 September 2009
3.1
Product data sheet
Serial Programming Interface
The CX24118A uses an I2C-compatible serial interface. The serial clock and data lines, SCL
and SDA, are used to transfer data at a clock rate of up to 1 MHz. A direct, exclusive
connection is preferred between controlling master and the tuner slave. If the chip is put on a
common I2C bus shared by other devices, the ongoing traffic on the bus may cause RF
interference. Both lines operate on 3.3 V I/O voltage levels. The SDA line is open drain,
requiring an external pull-up resistor.
The serial clock and data signals for a typical transaction is shown in Figure 5.
Figure 5.
Serial Clock and Data Signals
SCL
4
5
6
Start Condition
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
(1)
Slave
Address
Stop Condition
3
MSB
SDA
2
LSB
1
(1)
Register
Address
Data
(2)
FOOTNOTE:
(1)
(2)
Acknowledge generated by CX24118A.
Subsequent bytes are assumed to be data for registers whose addresses follow in ascending order.
102322_012
The START condition occurs on the falling edge of the SDA line when the SCL line is held
high. A STOP condition occurs on the rising edge of the SDA line when the SCL line is held
high. Every data word is 8 bits long with MSB first, followed by an acknowledge bit generated
by the receiving device. Each data transaction occurs between a START and a STOP
condition. The START condition is followed by a slave address. If this is the CX24118A
address, it generates an acknowledge bit on the SDA line.
The following are some typical read/write sequences:
Typical Single-Byte Write Procedure
1. Send the Start condition.
2. Send the CX24118A slave address, a write bit, and receive an ACK.
3. Send the CX24118A desired register address = n, and receive an ACK.
4. Send the byte for a desired register = n, and receive an ACK.
5. Send the Stop condition.
The above-described single-byte write procedure is shown in Figure 6.
In the figure, the following abbreviations are used:
‹ S = Start
‹ Dev Addr/wr = Device address with a write command
‹ A = Acknowledge
‹ P = Stop
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
23
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Figure 6.
Typical Single-Byte Write Procedure
S
Dev Addr/wr
A
Reg. Address = n
A
Data (n)
A
P
Master
Slave
Master
Slave
Master
Slave
102322_008
Typical Multiple-Bytes Write Procedure
1. Send the Start condition.
2. Send the CX24118A slave address, a write bit, and receive an ACK.
3. Send the CX24118A desired register address = n, and receive an ACK.
4. Send the byte destined for register n, and receive an ACK.
5. Send the byte destined for register n+1, and receive an ACK.
6. Send the byte destined for register n+2, and receive an ACK.
7. Send the data destined for register n+m, and receive an ACK
8. Send the Stop condition.
The above-described multiple-bytes write procedure is shown in Figure 7.
In the figure, the following abbreviations are used:
‹ S = Start
‹ Dev Addr/wr = Device address with a write command
‹ A = Acknowledge
‹ P = Stop
Figure 7.
Typical Multiple-Bytes Write Procedure
S
Dev Addr/wr
A
Reg. Address = n
A
Data (n)
A
Master
Slave
Master
Slave
Master
Slave
Data (n+1)
A
Data (n+2)
A
Data (n+m)
A
Master
Slave
Master
Slave
Master
Slave
P
102322_009
Typical Single-Byte Read Procedure
1. Send the Start condition.
2. Send the CX24118A slave address, a write bit, and receive an ACK.
3. Send the CX24118A desired register address = n, and receive an ACK.
4. Send the Start condition.
5. Send the part's slave address, a read bit, and receive an ACK.
6. Receive the byte from the desired register n, and do not supply an ACK.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
24
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
7. Send the Stop condition.
NOTE:
When reading data from a slave, no ACK is supplied from master after the
last desired byte.
The above-described single-byte read procedure is shown in Figure 8.
In the figure, the following abbreviations are used:
‹ S = Start
‹ Dev Addr/wr = Device address with a write command
‹ A = Acknowledge
‹ P = Stop
‹ Dev Addr/r = Device address with a read command
Figure 8.
Typical Single-Byte Read Procedure
S
Dev Addr/wr
A
Reg. Address = n
A
Master
Slave
Master
Slave
A
Data (n)
A
Slave
Master
Slave
S
Dev Addr/rd
Master
P
102322_010
Multiple-Bytes Read Procedure
1. Send the Start condition.
2. Send the CX24118A slave address, a write bit, and receive an ACK.
3. Send the CX24118A desired register address = n, and receive an ACK.
4. Send the Start condition.
5. Send the part's slave address, a read bit, and receive an ACK.
6. Receive the byte from register n, and supply an ACK.
7. Receive the byte from register n+1, and supply an ACK.
8. Receive the byte from register n+2, and supply an ACK.
9. Receive the data from register n+m, and do not supply an ACK.
10. Send the Stop condition.
NOTE:
When reading data from a slave, no ACK is supplied from master after the
last desired byte.
The above-described multiple-bytes read procedure is shown in Figure 9.
In the figure, the following abbreviations are used:
‹ S = Start
‹ Dev Addr/wr = Device address with a write command
‹ A = Acknowledge
‹ P = Stop
‹ Dev Addr/r = Device address with a read command
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
25
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Figure 9.
Typical Multiple-Bytes Read Procedure
S
Dev Addr/wr
A
Reg. Address = n
A
Master
Slave
Master
Slave
A
Data (n)
A
Data (n+1)
Slave
Master
Slave
S
Dev Addr/rd
Master
A
Data (n+m)
A
Slave
Master
P
102322_011
3.2
Registers
The register bit map is shown in Table 6.
Table 6.
Register Bit Map (Sheet 1 of 2)
Register Address(1)
D7
D6
D5
D4
D3
D2
D1
D0
OUTRefDiv
PLLRefDiv
Reserved
TUNLD
CPSel
Global
00
CHPId[7:0]
01
CHPVer[7:0]
02
Reserved
Tuner
10
11
DSMClkPol
DSMByp
CPLevel1[1:0]
12
BsDelayVal[3:0]
13
14
CPMan[1:0]
CPDVal[1:0]
CPLevel2[1:0]
CPLevel3[1:0]
Reserved
TUNAutoEn[1:0]
TUN1[5:0]
TUN2[7:0]
16
TUN3[7:0]
17
TUN4[7:0]
VCOSel[5]
19
1A
LODivSel
VCOSel[4:0]
VCOBandSel
PLLIntDiv[8:1]
PLLIntDiv[0]
PLLFracDiv[17:11]
CX24118A_N_2
Product data sheet
CPVal[1:0]
Reserved
15
18
CPCtrl
CPLevel4[1:0]
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
26
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Table 6.
Register Bit Map (Sheet 2 of 2)
Register Address(1)
D7
D6
D5
D4
1B
D3
D2
D1
D0
PLLFracDiv[10:3]
1C
PLLFracDiv[2:0]
1D
TUNReset
Reserved
Reserved
1E
BBFil1BW[1:0]
1F
Reserved
20
BBFAmpGain[3:0]
BBFil2BW[5:0]
BBVGA2Off[2:0]
Reserved
21
Reserved
BBVGA1Off[2:0]
RFVCABCDis
CPEn
PSEn
RFVCAOff[1:0]
BBEn
DCCorrEn
Reserved
Reserved
RFVCAEn
FOOTNOTES:
(1) The values in this column are hexadecimal.
3.3
Register Index
The register index is shown in Table 7.
Table 7.
Register Index
Address(1)
Field Name
Description
BBEn
21[3]
Baseband Enable.
BBFAmpGain[3:0]
1D[3:0]
Final Baseband Amplifier Gain.
BBFil1BW[1:0]
1E[7:6]
Baseband Filter 1 Bandwidth.
BBFil2BW[5:0]
1E[5:0]
Baseband Filter 2 Bandwidth.
BBVGA1Off[2:0]
1F[2:0]
Baseband VGA1 Offset Control.
BBVGA2Off[2:0]
1F[5:3]
Baseband VGA2 Offset Control.
BsDelayVal[3:0]
12[7:4]
VCO Tuning System Delay.
CHPId[7:0]
00[7:0]
Chip Identification Number.
CHPVer[7:0]
01[7:0]
Chip Version Number.
CPCtrl
12[2]
Charge Pump Control.
CPDVal[1:0]
10[3:2]
Digital Charge Pump Valve.
CPEn
21[5]
Charge Pump Enable.
CPLevel1[1:0]
11[7:6]
Automatic Charge Pump Level 1 Select.
CPLevel2[1:0]
11[5:4]
Automatic Charge Pump Level 2 Select.
CPLevel3[1:0]
11[3:2]
Automatic Charge Pump Level 3 Select.
CPLevel4[1:0]
11[1:0]
Automatic Charge Pump Level 4 Select.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
27
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Table 7.
Register Index
Address(1)
Field Name
Description
CPMan[1:0]
10[5:4]
Manual Analog Charge Pump Select.
CPSel
10[0]
Manual Override of Automatic Charge Pump Level Select.
CPVal[1:0]
12[1:0]
Analog Charge Pump Level.
DCCorrEn
21[2]
DC Offset Correction Enable.
DSMByp
10[6]
Delta Sigma Modulator Bypass.
DSMClkPol
10[7]
DSM Clock Polarity Select.
LODivSel
18[6]
Local Oscillator (LO) Divider Select.
OUTRefDiv
02[2]
Output Reference Divider.
PLLFracDiv[17:0]
1A[6:0],
1B[7:0],
1C[7:5]
PLL Fractional Divider.
PLLIntDiv[8:0]
19[7:0],
1A[7]
PLL Integer Divider.
PLLRefDiv
02[1]
PLL Reference Divider.
PSEn
21[4]
Prescaler Enable.
RFVCABCDis
20[4]
RF VCA Bias Control Circuit Disable.
RFVCAEn
21[0]
RF VCA Enable.
RFVCAOff[1:0]
20[3:2]
RF VCA Offset Select.
TUN1[5:0]
14[5:0]
Tuning System Configuration Register 1.
TUN2[7:0]
15[7:0]
Tuning System Configuration Register 2.
TUN3[7:0]
16[7:0]
Tuning System Configuration Register 3.
TUN4[7:0]
17[7:0]
Tuning System Configuration Register 4.
TunAutoEn[1:0]
14[7:6]
Auto-tuning System Enable.
TUNLD
10[1]
PLL Lock Detect.
TUNReset
1C[4]
Tuning System Reset.
VCOBandSel
18[0]
VCO Band Select.
VCOSel[5:0]
18[7],
18[5:1]
VCO Select.
FOOTNOTES:
The values in this column are hexadecimal.
(1)
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
28
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
3.4
Register Detail
This section provides the register detail.
NOTE:
POR refers to power-on reset value.
NOTE:
All bits in the registers are Read/Write unless indicated otherwise in the bit
description.
Register 00
Register (Hex)
POR
00
43
D7
D6
D5
D4
D3
D2
D1
D0
D3
D2
D1
D0
D3
D2
D1
D0
OUTRefDiv
PLLRefDiv
Reserved
CHPId[7:0]
Chip Identification Number.
The current chip ID is 0x23. Read only.
CHPId[7:0]
Register 01
Register
(Hex)
POR
01
03
D7
D6
D5
D4
CHPVer[7:0]
Chip Version Number.
The current chip version is 0x03. Read only.
CHPVer[7:0]
Register 02
Register
(Hex)
POR
02
00
D7
D6
D5
D4
Reserved
OUTRefDiv
Output Reference Divider.
This bit selects the reference clock divider for the CKREF_OUT pin. See Section 2.5 for more detail.
0 = ÷1.
1 = ÷2.
PLLRefDiv
PLL Reference Divider.
This bit selects the divider for the tuner synthesizer reference frequency.
0 = ÷1.
1 = ÷2.
Register 10
Register
(Hex)
POR
D7
D6
10
00
DSMClkPol
DSMByp
D5
D4
D3
CPMan[1:0]
CX24118A_N_2
Product data sheet
D2
CPDVal[1:0]
D1
D0
TUNLD
CPSel
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
29
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Register
(Hex)
POR
D7
D6
D5
D4
D3
D2
D1
D0
DSMClkPol
DSM Clock Polarity Select.
0 = No clock inversion.
1 = Clock inversion. Use this setting for normal operation.
DSMByp
Delta Sigma Modulator Bypass.
1 = Disables the delta sigma modulator, resulting in integer division.
0 = Delta sigma modulator along with prescaler defines the divider. Normal operation.
CPMan[1:0]
Manual Analog Charge Pump Select.
Selection of analog charge pump level in manual mode when register bit CPSel is set to 1. The levels are defined as
follows:
00b = 0.5 mA.
01b = 1.0 mA.
10b = 1.5 mA.
11b = 2.0 mA.
CPDVal[1:0]
Digital Charge Pump Valve.
The digital charge pump is enabled during tuning only.
00b = 0.5 x analog charge pump level.
01b = 1.0 x analog charge pump level.
10b = 2.0 x analog charge pump level. Use this setting for normal operation.
11b = 3.0 x analog charge pump level.
TUNLD
PLL Lock Detect.
0 = Synthesizer not frequency locked.
1 = Synthesizer is frequency locked.
CPSel
Manual Override of Automatic Charge Pump Level Select.
0 = Automatic charge pump current selection.
1 = Manual charge pump current selection.
Register 11
Register
(Hex)
POR
11
00
D7
D6
CPLevel1[1:0]
D5
D4
D3
CPLevel2[1:0]
CX24118A_N_2
Product data sheet
D2
CPLevel3[1:0]
D1
D0
CPLevel4[1:0]
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
30
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Register
(Hex)
POR
D7
D6
D5
D4
D3
D2
D1
D0
CPLevel1[1:0]
Automatic Charge Pump Level 1 Select.
Charge pump level 1 is selected by the automatic tuning system when the VCO tuning voltage is greater than 2.0 V.
For normal operation, set to 11b.
CPLevel2[1:0]
Automatic Charge Pump Level 2 Select.
Charge pump level 2 is selected by the automatic tuning system when the VCO tuning voltage is between 1.5 V and
2.0 V.
For normal operation, set to 11b.
CPLevel3[1:0]
Automatic Charge Pump Level 3 Select.
Charge pump level 3 is selected by the automatic tuning system when the VCO tuning voltage is between 1.0 V and
1.5 V.
For normal operation, set to 10b.
CPLevel4[1:0]
Automatic Charge Pump Level 4 Select.
Charge pump level 4 is selected by the automatic tuning system when the VCO tuning voltage is lower than 1.0 V.
For normal operation, set to 00b.
For each of the above register fields, the analog charge pump levels are set as follows:
00b = 0.5 mA.
01b = 1.0 mA.
10b = 1.5 mA.
11b = 2.0 mA.
Register 12
Register
(Hex)
POR
12
80
D7
D6
D5
D4
BsDelayVal[3:0]
D3
D2
Reserved
CPCtrl
D1
D0
CPVal[1:0]
VCO Tuning System Delay.
VCO tuning system delay in reference clock cycles between the time tuning system is enabled and tuning starts. The
default is 8 counts and can be set between 0 and 15 counts of reference cycle. The reference cycle period is:
BsDelayVal[3:0]
TREF = R/Reference oscillator frequency
R is the reference divider value selected by register bit PLLRefDiv (0x02[1]).
For normal operation, set to 0x8.
CPCtrl
Charge Pump Control.
0 = Analog charge pump turns OFF when the digital charge pump turns ON (when register bit TUNLD (0x10[1]) is
low).
1 = Analog charge pump always ON. Use this setting for normal operation.
CPVal[1:0]
Analog Charge Pump Level.
This is the value selected by the automatic tuning system, as specified in register 0x11. The values correspond to the
following charge pump levels. Read only.
00b = 0.5 mA.
01b = 1.0 mA.
10b = 1.5 mA.
11b = 2.0 mA.
Register 14
Register
(Hex)
POR
14
00
D7
D6
D5
D4
D3
TUNAutoEn[1:0]
D1
D0
TUN1[5:0]
CX24118A_N_2
Product data sheet
D2
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
31
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Register
(Hex)
POR
D7
D6
D5
D4
D3
D2
TUNAutoEn[1:0]
Auto-tuning System Enable.
00b = Auto-tuning mode. The auto-tuning system selects the VCO. Normal operation.
01b = Manual tuning mode. The VCO is selected using register field VCOSel[5:0].
10b - 11b = Reserved.
TUN1[5:0]
Tuning System Configuration Register 1.
For normal operation, set to 0x0F.
D1
D0
Register 15
Register
(Hex)
POR
15
00
D7
D6
D5
D4
D3
D2
D1
D0
D3
D2
D1
D0
D3
D2
D1
D0
D3
D2
D1
D0
TUN2[7:0]
Tuning System Configuration Register 2.
For normal operation, set to 0xFF.
TUN2[7:0]
Register 16
Register
(Hex)
POR
16
00
D7
D6
D5
D4
TUN3[7:0]
Tuning System Configuration Register 3.
For normal operation, set to 0xFF.
TUN3[7:0]
Register 17
Register
(Hex)
POR
17
00
D7
D6
D5
D4
TUN4[7:0]
Tuning System Configuration Register 4.
For normal operation, set to 0xF0.
TUN4[7:0]
Register 18
Register
(Hex)
POR
D7
D6
18
00
VCOSel[5]
LODivSel
D5
D4
VCOSel[4:0]
CX24118A_N_2
Product data sheet
VCOBandSel
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
32
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Register
(Hex)
POR
D7
D6
D5
D4
D3
D2
D1
D0
VCOSel[5]
VCO 6 Select.
This bit, when read, indicates if VCO6 is selected.
0 = VCO 6 deselected.
1 = VCO 6 selected when VCOSel[4:0] = 00000b.
LODivSel
Local Oscillator (LO) Divider Select.
This bit, when read, indicates the LO divider selected by the auto-tuning system. When written to, this bit selects the
divider.
0 = ÷2.
1 = ÷4.
VCOSel[4:0]
VCO Select.
These bits, when read, indicate the VCO selected by the auto-tuning system. The VCO can be manually selected by
writing to these bits. Only one VCO should be selected at a time.
00000b = None of these VCOs are selected.
00001b = VCO5 selected.
00010b = VCO4 selected.
00100b = VCO3 selected.
01000b = VCO2 selected.
10000b = VCO1 selected.
VCOBandSel
VCO Band Select.
This bit is common to all VCOs.
This bit, when read, indicates the VCO band selected by the auto-tuning system. When written to, this bit selects the
VCO band.
0 = High band.
1 = Low band.
Register 19 – 1C
Register
(Hex)
POR
19
00
1A
00
1B
00
1C
10
D7
D6
D5
D4
D3
D2
D1
D0
PLLIntDiv[8:1]
PLLIntDiv[0]
PLLFracDiv[17:11]
PLLFracDiv[10:3]
PLLFracDiv[2:0]
TUNReset
Reserved
PLLIntDiv[8:0]
PLL Integer Divider.
PLLFracDiv[17:0]
PLL Fractional Divider.
TUNReset
Tuning System Reset.
Setting this bit to 1 resets the auto-tuning system and starts the auto-tuning process. Write only.
Register 1D
Register
(Hex)
POR
1D
00
BBFAmpGain[3:0]
D7
D6
D5
D4
D3
Reserved
D1
D0
BBFAmpGain[3:0]
Final Baseband Amplifier Gain.
0000b = 37 dB gain.
0001b = 34 dB gain.
0011b = 31 dB gain. Use this setting under all conditions.
0111b = 28 dB gain.
1111b = 25 dB gain.
CX24118A_N_2
Product data sheet
D2
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
33
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Register 1E
Register
(Hex)
POR
1E
00
D7
D6
D5
D4
D3
BBFil1BW[1:0]
D2
D1
D0
BBFil2BW[5:0]
BBFil1BW[1:0]
Baseband Filter 1 Bandwidth.
00b = 100 MHz.
01b = 65 MHz. Use this setting for 30–45 MSps operation.
10b = 40 MHz. Use this setting for 20–30 MSps operation.
11b = 35 MHz. Use this setting for 1–20 MSps operation.
BBFil2BW[5:0]
Baseband Filter 2 Bandwidth.
The filter bandwidth set is given by:
BW = 2 + BBFil2BW[5:0]
The bandwidth is adjustable in 63 steps with a step size of 1 MHz. The bandwidth range is 2 MHz to
65 MHz.
Register 1F
Register
(Hex)
POR
1F
00
D7
D6
D5
Reserved
D4
D3
D2
BBVGA2Off[2:0]
D1
D0
BBVGA1Off[2:0]
BBVGA2Off[2:0]
Baseband VGA2 Offset Control.
000b = –41 dB.
100b = –39 dB.
010b = –37 dB.
110b = –35 dB.
001b = –33 dB.
101b = –31 dB. Use this setting when fixed gain settings are desired.
011b = –29 dB. Use this setting for minimum signal levels.
111b = –27 dB. Use this setting for maximum signal levels.
BBVGA1Off[2:0]
Baseband VGA1 Offset Control.
000b = –36 dB.
100b = –34 dB.
010b = –32 dB. Use this setting for minimum signal levels.
110b = –30 dB.
001b = –28 dB. Use this setting when fixed gain settings are desired.
101b = –26 dB.
011b = –24 dB.
111b = –22 dB. Use this setting for maximum signal levels.
Register 20
Register
(Hex)
POR
20
00
D7
D6
Reserved
D5
D4
D3
RFVCABCDis
CX24118A_N_2
Product data sheet
D2
RFVCAOff[1:0]
D1
D0
Reserved
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
34
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
Register
(Hex)
POR
D7
D6
D5
D4
D3
D2
D1
D0
RFVCABCDis
RF VCA Bias Control Circuit Disable.
The VCA is made up of multiple, parallel, gain stages. When stages are unused, they are either turned off, or
completely disabled by shutting off their bias, according to the state of this bit.
0 = Bias in unused stages is turned off.
1 = Bias in unused stages is not turned off.
RFVCAOff[1:0]
RF VCA Offset Select.
00b = –70 dB. Use this setting for maximum signal levels, and when fixed gain settings are desired.
01b = –67 dB.
10b = –64 dB. Use this setting for minimum signal levels.
11b = –61 dB.
Register 21
Register
(Hex)
POR
21
00
D7
D6
Reserved
CPEn
Charge Pump Enable.
1 = Enable.
0 = Disable.
PSEn
Prescaler Enable.
1 = Enable.
0 = Disable.
BBEn
Baseband Enable.
1 = Enable.
0 = Disable.
DCCorrEn
DC Offset Correction Enable.
1 = Enable.
0 = Disable.
RFVCAEn
RF VCA Enable.
1 = Enable.
0 = Disable.
D5
D4
D3
D2
D1
D0
CPEn
PSEn
BBEn
DCCorrEn
Reserved
RFVCAEn
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
35
CX24118A
NXP Semiconductors
Chapter 3: Serial Programming Interface and Registers
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
36
CX24118A
Chapter 4: Application Information
Rev. 02 — 8 September 2009
4.1
Product data sheet
Thermal Recommendations
The CX24118A uses a thermally enhanced QFN package with an exposed paddle
underneath the device to dissipate heat. The exposed paddle is soldered directly to exposed
PCB ground on the top layer of the board. Thermal vias then connect the top PCB layer to
the other board layers. The more layers that are used, the better the thermal properties of the
chip will be. Table 8 lists the CX24118A thermal layout recommendations.
Table 8.
Thermal Recommendations
Parameter
Recommendations
Number of PCB layers(1)
2 or 4
Numbers of thermal vias
16 (4x4 square matrix)
Thermal via spacing
0.85 mm from center to center
Solder mask opening under exposed
paddle(2)
3.7 x 3.7 mm
Metallization land pattern
3.7 x 3.7 mm
Via diameter
0.33 mm drill-hole size with 1 oz copper plating.
FOOTNOTES:
(1)
As many of the layers should be grounded and connected to the thermal vias as possible.
(2) Same as the package exposed paddle. The area outside the solder mask opening to the pin pads
should be covered with solder mask.
4.2
Sleep Mode Procedures
4.2.1
Changing from Normal Operation to Sleep Mode
To change the tuner from normal operation to sleep mode, use the following procedure:
1. Set register field TUNAutoEn[1:0] (0x14[7:6]) to 01b.
2. Set register field VCOSel[5:0] (0x18[7] and 0x18[5:0]) to 0.
3. Set the system enable bits (0x21[5:0]) to 0x00.
4.2.2
Changing from Sleep Mode to Normal Operation
To change the tuner from sleep mode to normal operation, use the following procedure:
1. Set register field TUNAutoEn[1:0] (0x14[7:6]) to 01b.
2. Set the system enable bits (0x21[5:0]) to 0x3F.
3. Restart the tuning system by setting TUNReset to 1.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
37
CX24118A
NXP Semiconductors
Chapter 4: Application Information
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
38
CX24118A
Chapter 5: Electrical, Thermal, and Mechanical Specifications
Rev. 02 — 08 September 2009
5.1
S11 Plot
Figure 10.
S11 Plot
m1
Product data sheet
m2
GENERAL NOTES:
1. m1
Frequency = 2.175 GHz
S (1,1) = 0.626 / -119.116
Impedance = Z0 * (0.304 - j0.547)
2. m2
Frequency = 925.0 MHz
S (1,1) = 0.482 / -84.258
Impedance = Z0 * (0.676 - j0.845), where Z0 = 50 Ω
3. The measurement was taken at the input of the device using a short 50 Ω coaxial cable stub.
102322_015
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 08 September 2009
39
CX24118A
NXP Semiconductors
Chapter 5: Electrical, Thermal, and Mechanical Specifications
5.2
Electrical and Thermal Specifications
5.2.1
Absolute Maximum Ratings
Table 9.
Absolute Maximum Ratings
Parameters
Minimum
Maximum
Units
Supply voltage
–0.3
3.6
V
Input voltage range (digital)
–0.3
Vcc
V
Storage temperature
–65
+150
°C
+150
°C
Junction temperature
5.2.2
Table 10.
Recommended Operating Conditions
Recommended Operating Conditions
Parameter
Ambient operating temperature
Supply voltage
5.2.3
Table 11.
Minimum
Typical
Maximum
Units
0
+25
+70
°C
3.13
3.3
3.47
V
Receiver Electrical and Thermal Specifications
Receiver Electrical Specifications (Sheet 1 of 3)
Parameter
Conditions
Min
Typ
Max
Units
Supply current
160
240
mA
Powerdown current(1)
11
mA
RF frequency
925
2175
MHz
Input power(2)
–69
(–81)
–23
(–6)
dBm
–70
dBm
3
Volts
LO leakage(4)
–80
Gain control voltage
Maximum voltage gain
0.1
At 1 MSps (Pin = –81 dBm)
77
dB
At 20 MSps (Pin = –70 dBm)
66
dB
At 45 MSps (Pin = –65 dBm)
61
dB
AGC range
Gain control voltage
0.5 to 2.5 V
90
Vout into minimum load of 500 Ω single-ended
or 1 kΩ differential
Single-ended
500
CX24118A_N_2
Product data sheet
dB
1000
mVpp
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 08 September 2009
40
CX24118A
NXP Semiconductors
Chapter 5: Electrical, Thermal, and Mechanical Specifications
Table 11.
Receiver Electrical Specifications (Sheet 2 of 3)
Parameter
Conditions
Min
Typ
Max
Units
Harmonics on baseband outputs @ 1 Vpp output
level (single-ended)
–30
dBc
I/Q phase balance
±3
±5
Deg.
I/Q amplitude balance
±1
±3
dB
12
dB
Noise figure floor at minimum input level of
–70 dBm
SR = 20 MSps, filter BW = 18.5 MHz
10
Passband amplitude ripple at baseband output
DC to 0.8 x f3dB(4)
1
dB
Group delay ripple at baseband output
170 kHz to 0.8 x f3dB
SR = 1 MSps
f3dB = 3.175 MHz(5)
66
ns
SR = 20 MSps
f3dB = 16 MHz(5)
57
ns
SR = 45 MSps
f3dB = 33 MHz(5)
37
ns
Stopband attenuation at 2 * f3dB(4) at baseband
output
33
dB
Stopband attenuation at 3 * f3dB(4) at baseband
output
40
dB
IIP3 (Out-of-band)(6)
+(31 and 60) MHz, Pin = –30 dBm(8)
–5
10
dBm
+(91 and 180) MHz, Pin = –30 dBm(8)
5.5
10
dBm
In-Band OIP3 (into 1 kΩ load)
–1
18
dBm
Spurious rejection (2xLO – RF) wanted and
interferer level set at –25dBm
–30
–40
dBc
Spurious rejection (2xRF - LO) wanted and
interferer level set at –25 dBm
–40
–45
dBc
θjc: using two-layer board
7.2
°C/W
θja: using two-layer board
47
°C/W
θjc: using four-layer board
4.8
°C/W
θja: using four-layer board
31.5
°C/W
Thermal resistance
of package
Serial Interface Specifications
Serial programming interface clock frequency
Input voltage
1
High logic voltage: VIH
Low logic voltage: VIL
2.1
MHz
V
1.05
V
LO Specifications
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 08 September 2009
41
CX24118A
NXP Semiconductors
Chapter 5: Electrical, Thermal, and Mechanical Specifications
Table 11.
Receiver Electrical Specifications (Sheet 3 of 3)
Parameter
Conditions
Operating VCO frequency
Min
Typ
2330
Max
Units
4660
MHz
Tuning step size @ 40 MHz fref
160
Hz
Reference frequency
40
MHz
Spurs
1 MHz to 40 MHz offset frequencies
–40
–30
dBc
Integrated DSB phase noise with 40 MHz reference
frequency
Integrated from 1 kHz to 1 MHz offset
frequencies
–44
–36
dBc
Lock time(8)
Between any two frequencies within the
operating range of 925 MHz to 2175
MHz
1
5
msec
Reference Oscillator Output Specifications
Reference oscillator output frequency(9)
40 (20)
MHz
2
Vp–p
1.6
V
Reference oscillator output level
Reference oscillator output DC offset
FOOTNOTES:
This is the current drawn when all blocks are disabled except the crystal oscillator and digital sections.
(2)
–25 dBm is single tone power and –6 dBm is the aggregate average power of 40 QPSK modulated carriers.
–69 dBm is the minimum power at 20 MSps, and –81 dB is the minimum power at 1 MSps.
(3) This LO leakage is at RF_INP pin from 925 MHz–2175 MHz.
(1)
(4)
SR
2
1
2
f3dB is the baseband bandwidth given by: -------- × ( 1 + alpha ) + LNB offset + --- × ( PLL step size )
(5)
f3dB is calculated for alpha of 0.35, LNBoffset of 2.5 MHz. PLL step size, being very small (160 Hz), can be ignored.
These IIP3 tone offsets are specifically for a symbol rate of 20 MSps, with the overall filter bandwidth set at 18.5 MHz and the bandwidth
of the filter at the mixer output set at 35 MHz. The IIP3 tone offsets scale with symbol rate assuming a channel spacing of 1.5*SR. Thus
the ±(31,60) MHz tones correspond to ±(1.5*SR, 3*SR) MHz and the ±(91,180) MHz tones correspond to ±(4.5*SR, 9*SR) MHz.
(7) This level is derived assuming –23 dBm is the maximum level of all other transponders, an operating symbol rate of 20 MSps and a C/I of
7 dB.
(8) From after serial communication has been received to stable lock.
(9)
The output level is across 10 kΩ || 20 pF load. The output waveform is sinusoidal when register bit OUTRefDiv (0x02[2]) is set to ÷1, and
is a square wave when OutRefDiv is set to ÷2.
(6)
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 08 September 2009
42
CX24118A
NXP Semiconductors
Chapter 5: Electrical, Thermal, and Mechanical Specifications
5.3
Mechanical Specifications
The CX24118A uses two 36-pin Quad Flat No-Lead (QFN) plastic packages.
The CX24118A package diagrams are shown in Figure 11 and Figure 12.
Figure 11.
Package Diagram
b
4xP
D
D2
Pin 1
Indicator
D1
Pin 1
Indicator
4xP
D
1
1
2
2
3
3
D1
D2
L
TOP VIEW
e
BOTTOM VIEW
θ
See Detail A
Seating
Plane
A2
A3
A
A1
SIDE VIEW
b
A1
Detail A
Dim.
A
A1
A2
A3
D
D1
D2
b
e
L
P
θ
All Dimensions
in Millimeters
Min.
Nom. Max.
---0.00
----
3.55
0.18
0.50
0.24
----
0.85
0.01
0.65
0.20 REF.
6.00 BSC
5.75 BSC
3.70
0.23
0.50 BSC
0.60
0.42
----
0.90
0.05
0.70
3.85
0.30
0.75
0.60
12O
102322_006
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 08 September 2009
43
CX24118A
NXP Semiconductors
Chapter 5: Electrical, Thermal, and Mechanical Specifications
Figure 12.
Package Diagram
HVQFN36: plastic thermal enhanced very thin quad flat package; no leads;
36 terminals; body 6 x 6 x 0.85 mm
A
B
D
SOT1092-2
terminal 1
index area
E
A
A1
c
detail X
e1
e
10
18
C
C A B
C
v
w
b
y1 C
y
L
19
9
e
e2
Eh
1
27
terminal 1
index area
36
28
X
Dh
0
2.5
Dimensions
Unit
A(1)
A1
b
max 1.00 0.05 0.30
nom 0.85 0.02 0.21
min 0.80 0.00 0.18
mm
5 mm
scale
c
D(1)
Dh
E(1)
Eh
e
e1
e2
L
v
0.2
6.1
6.0
5.9
4.05
3.90
3.75
6.1
6.0
5.9
4.05
3.90
3.75
0.5
4
4
0.65
0.55
0.45
0.1
w
y
0.05 0.05
y1
0.1
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
Outline
version
SOT1092-2
References
IEC
JEDEC
JEITA
---
---
CX24118A_N_2
Product data sheet
sot1092-2_po
European
projection
Issue date
09-02-23
09-02-24
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 08 September 2009
44
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
Legal information
Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
CX24118A_N_2
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 02 — 8 September 2009
45
CX24118A
NXP Semiconductors
Advanced Modulation Digital Satellite Tuner
46
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 8 September 2009
Document identifier: CX24118A_N_2