KEMET C1210X473KCRACTU

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP)
X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Overview
KEMET’s High Voltage with Flexible Termination (HV FT-CAP)
surface mount MLCCs in X7R dielectric combine high voltage and
flexible termination technologies. Featuring a 125°C maximum
operating temperature and considered “temperature stable,”
these devices address the primary failure mode of MLCCs—flex
cracks, which are typically the result of excessive shear stresses
produced during board flexure or thermal cycling. Utilizing a
conductive silver epoxy between the base metal and nickel
barrier layers of KEMET’s standard termination system, flexible
termination technology directs board flex stress away from the
ceramic body and into the termination area, therefore mitigating
flex cracks which can result in low IR or short circuit failures.
Although flexible termination technology does not eliminate the
potential for mechanical damage that may propagate during
extreme environmental and handling conditions, it does provide
superior flex performance over standard termination systems.
The HV FT-CAP offers low leakage current, exhibits low ESR at
high frequencies and finds conventional use as snubbers or filters
in applications such as switching power supplies and lighting
ballasts. Their exceptional performance at high frequencies has
made them a preferred choice of design engineers worldwide.
In addition to their use in power supplies, these capacitors
are widely used in industries related to telecommunications,
medical, military, aerospace, semiconductors and test/diagnostic
equipment.
Combined with the stability of an X7R dielectric and designed to
accommodate all capacitance requirements, these flex-robust
devices are RoHS-compliant, offer up to 5mm of flex-bend
capability and exhibit a predictable change in capacitance with
respect to time and voltage. Capacitance change with reference
to ambient temperature is limited to ±15% from -55°C to +125°C.
Benefits
Applications
•
•
•
•
•
•
•
•
•
•
-55°C to +125°C operating temperature range
Superior flex performance (up to 5mm)
Pb-Free and RoHS compliant
EIA 0805, 1206, 1210, 1808, 1812, 1825, 2220 and 2225 case sizes
DC voltage ratings of 500V, 630V, 1KV, 1.5KV, 2KV, 2.5KV and 3KV
Capacitance offerings ranging from 62pF to 0.27μF
Available capacitance tolerances of ±5%, ±10% or ±20%.
Low ESR and ESL
Non-polar device, minimizing installation concerns
100% pure matte tin-plated end metallization allowing for
excellent solderability
• SnPb plated end metallization option available upon request (5% min)
Typical applications include switch mode power supplies (input
filters, resonators, tank circuits, snubber circuits, output filters),
high voltage coupling and DC blocking, lighting ballasts, voltage
multiplier circuits, DC/DC converters and coupling capacitors in
Ćuk converters. Markets include power supply, LCD fluorescent
backlight ballasts, HID lighting, telecom equipment, industrial and
medical equipment/control, LAN/WAN interface, analog and digital
modems, and automotive. X7R dielectrics are not designed for AC
line filtering or pulse applications.
Ordering Information
C
Ceramic
1210
Case Size Specification/
(L" x W")
Series
0805
1206
1210
1808
1812
1825
2220
2225
1
2
X
X = Flexible
Termination
473
K
C
R
A
C
TU
Capacitance
Code (pF)
Capacitance
Tolerance
Voltage
Dielectric
Failure Rate/
Design
End Metallization1
Packaging/Grade
(C-Spec)2
C = 500V
B = 630V
D = 1000V
F = 1500V
G = 2000V
Z = 2500V
H = 3000V
R = X7R
A = N/A
2 Sig. Digits +
Number of Zeros
J = ±5%
K = ±10%
M = ±20%
C = 100% Matte Sn
L = SnPb (5% min)
Blank = Bulk
TU = 7" Reel
Unmarked
TM = 7" Reel Marked
Additional termination options may be available. Contact KEMET for details.
Additional reeling or packaging options may be available. Contact KEMET for details.
One WORLD
One Brand
One Strategy
One Focus
One Team
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
One KEMET
C1025-1 • 9/13/2010
1
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Dimensions – Millimeters (Inches)
W
L
B
T
S
EIA Size
Code
Metric Size
Code
L Length
W Width
B Bandwidth
0805
1206
1210
1808
1812
1825
2220
2225
2012
3216
3225
4520
4532
4564
5650
5664
2.1 (.083) ± 0.30 (.012)
3.3 (.130) ± 0.40 (.016)
3.3 (.130) ± 0.40 (.016)
4.7 (.185) ± 0.50 (.020)
4.5 (.178) ± 0.40 (.016)
4.6 (.181) ± 0.40 (.016)
5.9 (.232) ± 0.75 (.030)
5.9 (.232) ± 0.75 (.030)
1.25 (.049) ± 0.20 (.008)
1.60 (.063) ± 0.20 (.008)
2.50 (.098) ± 0.20 (.008)
2.00 (.079) ± 0.20 (.008)
3.20 (.126) ± 0.30 (.012)
6.40 (.252) ± 0.40 (.016)
5.00 (.197) ± 0.40 (.016)
6.40 (.248) ± 0.40 (.016)
0.50 (0.02) ± 0.25 (.010)
0.60 (.024) ± 0.25 (.010)
0.60 (.024) ± 0.25 (.010)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
T Thickness
Mounting
Technique
Solder Wave or
Solder Reflow
See Table 2 for
Thickness
Solder Reflow
Only
Qualification/Certification
Commercial grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table
4, Performance and Reliability.
Environmental Compliance
RoHS PRC ( Peoples Republic of China) compliant
Electrical Parameters/Characteristics
Item
Parameters/Characteristics
Operating Temperature Range:
Capacitance Change with Reference to +25°C and 0 Vdc Applied (TCC):
Aging Rate (Max % Cap Loss/Decade Hour):
Dielectric Withstanding Voltage:
Dissipation Factor (DF) Maximum Limit @ 25ºC:
Insulation Resistance (IR) Limit @ 25°C:
Insulation Resistance (IR) Limit @ 125°C:
-55°C to +125°C
±15%
3.5%
150% of rated voltage for voltage rating of < 1000V
120% of rated voltage for voltage rating of ≥ 1000V
2.5%
1000 megohm microfarads or 100GΩ
100 megohm microfarads or 10GΩ
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and Dissipation Factor (DF) measured under the following conditions:
1kHz and 1 Vrms if capacitance >1000pF
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
2
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Table 1A – (0805 - 1812 Case Sizes)
Cap
Cap
Code
Series
Voltage Code
C0805
C
B
C1206
D
C
B
D
C1210
F
G
C
B
D
C1808
F
G
C
B
D
F
C1812
G
Z
H
C
B
D
F
G
Z
H
Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000
Cap Tolerance
Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions
10 pF
100
J
K M
11 pF
110
J
K M
12 pF
120
J
K M
13 pF
130
J
K M
15 pF
150
J
K M
16 pF
160
J
K M
18 pF
180
J
K M
20 pF
200
J
K M
22 pF
220
J
K M
24 pF
240
J
K M
27 pF
270
J
K M
30 pF
300
J
K M
33 pF
330
J
K M
J
K M
36 pF
360
39 pF
390
J
K M
43 pF
430
J
K M
47 pF
470
J
K M
51 pF
510
J
K M
56 pF
560
J
K M
62 pF
620
J
K M DG DG DG
68 pF
680
J
K M DG DG DG
75 pF
750
J
K M DG DG DG EG EG EG
82 pF
820
J
K M DG DG DG EG EG EG
91 pF
910
J
K M DG DG DG EG EG EG
100 pF
101
J
K M DG DG DG EG EG EG
110 pF
111
J
K M DG DG DG EF EF EF
120 pF
121
J
K M DG DG DG EF EF EF
130 pF
131
J
K M DG DG DG EF EF EF
150 pF
151
J
K M DG DG DG EF EF EF
180 pF
181
J
K M DG DG DG EF EF EF
220 pF
221
J
K M DG DG DG EF EF EF
270 pF
271
J
K M DG DG DG EF EF EF
330 pF
331
J
K M DG DG DG EF EF EF
390 pF
391
J
K M DG DG DG EF EF EF
470 pF
471
J
K M DG DG DG EF EF EF
560 pF
561
J
K M DG DG DG EF EF EF
680 pF
681
J
K M DG DG DG EF EF EF
820 pF
821
J
K M DG DG DG EF EF EF
1,000 pF
102
J
K M DG DG DG EF EF EF
1,200 pF
122
J
K M DG DG DG EF EF EF
1,500 pF
152
J
K M DG DG DG EF EF EF
1,800 pF
182
J
K M DG DG DG EF EF EF
2,000 pF
202
J
K M DG DG DG EF EF EF
2,200 pF
222
J
K M DG DG DG EF EF EF
2,700 pF
272
J
K M DG DG DG EF EF EF
3,300 pF
332
J
K M DG DG DG EF EF EF
3,900 pF
392
J
K M DG UD UD EF EF EF
4,700 pF
472
J
K M DG UD UD EF EF EF
EF EF
5,600 pF
J1210
K M DG XUD UD EF 473
C562
6,800 pF
682
J
K M DG UD UD EG EG EG
Case
Capacitance
EG EG
8,200 pF Ceramic
822
J Size
K MSpecifi
DG cation/
UD UD EG
(L"
Series
EG(pF)EG
10,000 pF
103
J x W")
K M UD
UD UD EGCode
12,000 pF
123
J
K M UD UD UD EG UD UD
0805
X = Flexible
2 Sig. Digits +
15,000 pF
153
J
K M UD UD UD EG UD UD
1206
Termination Number of Zeros
18,000 pF
183
J
K M UD UD UD UD UD UD
1210K M
J
22,000 pF
223
UD
UD UD UD
27,000 pF
273
J1808K M UD
UD UD UD
1812
1825
Cap
Voltage
2220 Code C B D
Code
2225
Series
C0805
EG
EG
EG
EG
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
EG
LB LB LB LB LB LB LB
LB LB LB LB LB LB LB
LB LB LB LB LB LB LB
LB LB LB LB LB LB LB
LB LB LB LB LB LB LB
LA LA LA LA LB LB LB
FL FL FL FL FL LA LA LA LA LB LB LB
FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK
FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK
FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK
FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK
FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK
FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK
FL FL FL FL FL LA LA LA LA LB LB LC GH GH GH GH GH
FL FL FL FL FL LA LA LA LA LB LB LC GH GH GH GH GH
EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH
EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH
EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH
EG FL FL FL FL FM LB LB LB LB LC
GH GH GH GH GH
EG FL FL FL FL FM LA LA LA LB LC
GH GH GH GH GH
EG FL FL FL FL FM LA LA LA LB LC
GH GH GH GH GH
EG FL FL FL FL FM LA LA LA LB LC
GH GH GH GH GH
GH GH GH GH GH
EG FL FL FL FL FM LA LA LA LB LC
FL FL FL FL FM LA LA LA LB LC
GH GH GH GH GK
FL FL FL FL FM LA LA LA LB
GH GH GH GH GK
FL FL FL FL FK LA LA LA LB
GH GH GH GH GK
FL FL FL FL FK LA LA LA LB
GH GH GH GH
GH GH GHTUGK
K FL FL CFL FM R LA LB ALB LC
C
FL FL FL FM
LA LB LB LC
GH GH GH GK
Rate/LC
Capacitance
Packaging/Grade
FL FLVoltage
FL FK Dielectric
LA Failure
LB LB
End Metallization1 GH GH GH GK2
Tolerance
FL FL FL FK
LA LBDesign
LB LC
GH GH (C-Spec)
GH GK
FL FK
LA LC LC
GK GK GK
J = ±5%FL FL
C = 500V
R = X7R
A = N/A
C = 100% Matte SnGH Blank
= Bulk
FL FL FL
LA LC LC
GH GK GK
K = ±10% B = 630V
L = SnPb (5% min) TU = 7" Reel
FL FL FL
LA UD UD
GH GK GK
M = ±20%
D = 1000V
Unmarked
FL FM FM
LA UD UD
GH GK GK
F = 1500V
FM FK
FK
LA UD UD
GH TM = 7" Reel Marked
G = 2000V
Z = 2500V
BH = 3000V
D
F
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000
Cap
C
B
D
C1206
F
G
C
C1210
G
C
B
D
F
C1808
G
Z
H
C
B
D
F
G
Z
H
C1812
UD = Under Developement
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Roll Over for
Order Info.
C1025-1 • 9/13/2010
3
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Table 1A con't – (0805 - 1812 Case Sizes)
Cap
Cap
Code
33,000 pF
39,000 pF
47,000 pF
56,000 pF
68,000 pF
82,000 pF
0.10 uF
0.12 uF
0.15 uF
0.18 uF
0.22 uF
0.27 uF
0.33 uF
333
393
473
563
683
823
104
124
154
184
224
274
334
Series
C0805
Voltage Code
C
B
C1206
D
C
B
D
C1210
F
G
C
B
D
C1808
F
G
C
B
D
F
C1812
G
Z
H
C
B
D
F
G
Z
H
Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000
Cap Tolerance
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
M
M
M
M
M
M
M
M
M
M
M
Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions
UD
UD UD UD
UD UD UD
UD UD UD
UD
UD
UD
UD
FM
FK
FK
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD
UD UD
UD UD
UD UD
UD
UD
UD
UD
LC
LC
LC
LC
UD
UD
UD
UD
UD
UD
UD
GH
GH
GH
GH
GK
GK
GK
Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000
Cap
Cap
Voltage Code C
Code
Series
B
D
C
B
C0805
D
F
G
C
B
C1206
D
F
G
C
B
D
C1210
F
G
Z
H
C
B
D
F
C1808
G
Z
H
C1812
Table 1B – (1825 - 2225 Case Sizes)
Cap
Cap
Code
Series
C1825
Voltage Code
C
B
Voltage VDC
500
630
Cap Tolerance
Cap
1812
Voltage VDC
1825
Voltage Code
2220
2225Series
F
G
Z
H
1000 1500 2000 2500 3000
C
B
500
630
D
F
C2225
G
Z
H
1000 1500 2000 2500 3000
C
B
500
630
D
F
G
Z
H
1000 1500 2000 2500 3000
Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions
100 pF
101
J
K
M
110 pF
111
J
K
M
120 pF
121
J
K
M
130 pF
131
J
K
M
150 pF
151
J
K
M
180 pF
181
J
K
M
220 pF
221
J
K
M
270 pF
271
J
K
M
330 pF
331
J
K
M
HG
390 pF
391
J
K
M
HG
K
M
HG
470 pF
471
J
560 pF
561
J
K
M
HG
680 pF
681
J
K
M
HG
820 pF
821
J
K
M
HG
1,000 pF
102
J
K
M
HG
1,200 pF
122
J
K
M
HG
1,500 pF
152
J
K
M
HG
1,800 pF
182
J
K
M
HE
C
1210
X
2,000 pF
202
J
K
M
HE
2,200 pF
222 Case
J SizeK Specifi
M cation/
HE
2,700 pF Ceramic
272
M
HE
(L" xJ W") K
Series
3,300 pF
332
J
K
M
HE
0805
= Flexible
3,900 pF
392
J
K XM
HE
1206
4,700 pF
472
J
K Termination
M
HE
5,600 pF
562
J
K
M
HE
1210
6,800 pF
682
J
K
M
HE
1808
Cap
Code
D
C2220
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HG
HE
HE
HE
473 HE
HE
HE
HE Capacitance
HE
HE
HE
HE
Code
(pF)HE
HE
HE
HE
HE2 Sig.
HEDigitsHE+
Number
HE
HE of Zeros
HE
HE
HE
HE
HE
HE
HE
500
630
C
B
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HG
HG
HG
JP
JP
JP
HE
HG
HG
JP
JP
JP
C
RJE
HE KHG
HG
JE
JE
HE
HG
HG
JE
JE
JE
Capacitance
HG Voltage
JE
JE Dielectric
JE
HE
HG
Tolerance
HE
HG
HG
JE
JE
JE
C = 500V
X7R
HEJ = ±5%
JE
JE R = JE
B = 630V
HEK = ±10%
JE
JE
JE
HEM = ±20% D = 1000V
JE
JE
JE
HE
JE
JE
JE
F = 1500V
2000V630
1000 1500 2000 2500 3000G = 500
D
F
C1825
G
Z
H
Z = 2500V
C
B
H = 3000V
JP
JP
JP
JP
JP
JP
JP
JP
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
JP
JP
JP
JP
KF
KF
KF
KF
KF
AJE JP JP C KF KF KF KF
TU KF
JE
JE
JP
KF
KF
KF
KF
KF
FailureJERate/JP
Packaging/Grade
1
Metallization
JE
JE
JP EndJP
KE
KE
KE
KE
2KE
Design
(C-Spec)
JE
JE
JP
JP
KE
KE
KE
KE
KE
N/A JPC = 100%
JE A = JE
JP Matte
KE Sn
KE Blank
KE = Bulk
KE
KE
L = SnPb (5%
JE
JP
KE min)KE TUKE= 7" Reel
KE
KE
JE
JP
KE
KE
KE Unmarked
KE
KE
JE
JP
KE
KE TM
KE= 7" Reel
KE Marked
KF
1000 1500 2000 2500 3000
D
F
G
C2220
Z
H
500
630
C
B
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
1000 1500 2000 2500 3000
D
F
G
Z
H
C2225
UD = Under Developement.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Roll Over for
Order Info.
C1025-1 • 9/13/2010
4
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Table 1B con't – (1825 - 2225 Case Sizes)
Cap
Cap
Code
8,200 pF
10,000 pF
12,000 pF
15,000 pF
18,000 pF
22,000 pF
27,000 pF
33,000 pF
39,000 pF
47,000 pF
56,000 pF
68,000 pF
82,000 pF
0.10 uF
0.12 uF
0.15 uF
0.18 uF
0.22 uF
0.27 uF
0.33 uF
0.39 uF
0.47 uF
0.56 uF
0.68 uF
0.82 uF
1.0 uF
1.2 uF
1.5 uF
1.8 uF
2.2 uF
2.7 uF
3.3 uF
822
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
564
684
824
105
125
155
185
225
275
335
Cap
Cap
Code
Series
C1825
Voltage Code
C
B
Voltage VDC
500
630
HE
HE
HE
HE
HE
HE
HE
HE
HE
HE
HE
HG
HG
HG
HG
HG
HG
HG
HE
HE
HE
HE
HE
HG
HG
HG
HG
HG
Voltage VDC
500
630
Voltage Code
C
B
Cap Tolerance
C
Ceramic
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
D
Z
H
C
B
500
630
D
F
C2225
G
Z
H
1000 1500 2000 2500 3000
C
B
500
630
D
F
G
Z
H
1000 1500 2000 2500 3000
Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
HE
HE
HE
HE
HE
HG
HG
HG
HG
HG
HE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JE
JP
JP
JP
JE
JE
JP
JP
JP
JP
JP
JP
JP
JP
1000 1500 2000 2500 3000
500
630
C
B
D
HE
HE
HG
HG
HG
HG
HG
F
G
Z
H
JE
JE
JP
JP
JP
JP
JP
JP
JP
JP
JP
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
1000 1500 2000 2500 3000
500
630
X
X = Flexible
Termination
JE
JE
JP
JP
JP
JP
JP
JP
C
B
D
C1825
Case Size Specification/
(L" x W")
Series
0805
1206
1210
1808
1812
1825
2220
2225
G
1000 1500 2000 2500 3000
Series
1210
F
C2220
F
G
Z
H
C2220
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
1000 1500 2000 2500 3000
D
F
G
473
K
C
R
A
C
TU
Capacitance
Code (pF)
Capacitance
Tolerance
Voltage
Dielectric
Failure Rate/
Design
End Metallization1
Packaging/Grade
(C-Spec)2
C = 500V
B = 630V
D = 1000V
F = 1500V
G = 2000V
Z = 2500V
H = 3000V
R = X7R
A = N/A
2 Sig. Digits +
Number of Zeros
J = ±5%
K = ±10%
M = ±20%
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Roll Over for
Order Info.
Z
H
C2225
C = 100% Matte Sn
L = SnPb (5% min)
Blank = Bulk
TU = 7" Reel
Unmarked
TM = 7" Reel Marked
C1025-1 • 9/13/2010
5
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Table 2 – Chip Thickness / Packaging Quantities
Thickness
Code
AA
AB
BB
CB
CC
CD
DC
DD
DL
DE
DF
DG
DH
EB
EK
EC
EN
ED
EE
EF
EM
EG
EH
EJ
FB
FC
FD
FE
FF
FG
FL
FO
FH
FP
FM
FJ
FN
FT
FK
FR
FS
PA
MA
NA
NA
LD
LA
LB
LC
GB
GC
GD
GE
GH
GF
GG
GK
GJ
GN
GL
GM
GO
HB
HC
HD
HE
HF
HG
JB
JC
JD
JE
JF
JP
JG
JH
JO
KB
KC
KD
KE
KF
Chip
Size
01005
0201
0402
0603
0603
0603
0805
0805
0805
0805
0805
0805
0805
1206
1206
1206
1206
1206
1206
1206
1206
1206
1206
1206
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1210
1220
1632
1706
1706
1808
1808
1808
1808
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
1812
1825
1825
1825
1825
1825
1825
2220
2220
2220
2220
2220
2220
2220
2220
2220
2225
2225
2225
2225
2225
Thickness ±
Range (mm)
0.20 ± 0.02
0.30 ± 0.03
0.50 ± 0.05
0.80 ± 0.07
0.80 ± 0.10
0.80 ± 0.15
0.78 ± 0.10
0.90 ± 0.10
0.95 ± 0.10
1.00 ± 0.10
1.10 ± 0.10
1.25 ± 0.15
1.25 ± 0.20
0.78 ± 0.10
0.80 ± 0.10
0.90 ± 0.10
0.95 ± 0.10
1.00 ± 0.10
1.10 ± 0.10
1.20 ± 0.15
1.25 ± 0.15
1.60 ± 0.15
1.60 ± 0.20
1.70 ± 0.20
0.78 ± 0.10
0.90 ± 0.10
0.95 ± 0.10
1.00 ± 0.10
1.10 ± 0.10
1.25 ± 0.15
1.40 ± 0.15
1.50 ± 0.20
1.55 ± 0.15
1.60 ± 0.20
1.70 ± 0.20
1.85 ± 0.20
1.85 ± 0.20
1.90 ± 0.20
2.10 ± 0.20
2.25 ± 0.20
2.50 ± 0.20
0.80 ± 0.10
0.80 ± 0.10
0.90 ± 0.10
0.90 ± 0.10
0.90 ± 0.10
1.40 ± 0.15
1.60 ± 0.15
2.00 ± 0.15
1.00 ± 0.10
1.10 ± 0.10
1.25 ± 0.15
1.30 ± 0.10
1.40 ± 0.15
1.50 ± 0.10
1.55 ± 0.10
1.60 ± 0.20
1.70 ± 0.15
1.70 ± 0.20
1.90 ± 0.20
2.00 ± 0.20
2.50 ± 0.20
1.10 ± 0.15
1.15 ± 0.15
1.30 ± 0.15
1.40 ± 0.15
1.50 ± 0.15
1.60 ± 0.20
1.00 ± 0.15
1.10 ± 0.15
1.30 ± 0.15
1.40 ± 0.15
1.50 ± 0.15
1.60 ± 0.20
1.70 ± 0.15
1.80 ± 0.15
2.40 ± 0.15
1.00 ± 0.15
1.10 ± 0.15
1.30 ± 0.15
1.40 ± 0.15
1.60 ± 0.20
Qty per Reel
7" Plastic
4000
2500
2500
2500
2500
4000
2000
4000
4000
2500
2500
2500
2500
2000
2000
2000
4000
4000
4000
2500
2500
2500
2000
2000
2000
2000
2000
2000
2000
1500
2000
2000
1000
4000
4000
4000
4000
2500
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
500
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
500
1000
1000
1000
1000
1000
Qty per Reel
13" Plastic
10000
10000
10000
10000
10000
10000
8000
10000
10000
10000
10000
10000
10000
8000
8000
8000
10000
10000
10000
10000
10000
10000
8000
8000
8000
8000
8000
8000
8000
4000
8000
8000
4000
10000
10000
10000
10000
10000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
2000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
2000
4000
4000
4000
4000
4000
Qty per Reel
7" Paper
15000
15000
10000
4000
4000
4000
4000
4000
4000
Qty per Reel
13" Paper
Qty per Bulk
Cassette
50000
10000
10000
10000
10000
10000
50000
15000
10000
Package Quantity
Based on Finished Chip
Thickness Specifications
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
6
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Soldering Process
Recommended Soldering Technique:
• Solder wave or solder reflow for case sizes 1206 and less
• Case sizes 1210 and greater are limited to solder reflow only
Recommended Soldering Profile
• KEMET recommends following the guidelines outlined in IPC/JEDEC J-STD-020D.1
Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC-7351 (mm)
EIA
Size
Code
Metric
Size
Code
Density Level A:
Maximum (Most)
Land Protrusion (mm)
C
Y
X
V1
Density Level B:
Median (Nominal)
Land Protrusion (mm)
V2
C
Y
X
V1
Density Level C:
Minimum (Least)
Land Protrusion (mm)
V2
C
Y
X
V1
V2
0603
1608
0.85
1.25
1.10
4.00
2.10
0.75
1.05
1.00
3.10
1.50
0.65
0.85
0.90
2.40
1.20
0805
2012
1.05
1.45
1.55
4.60
2.60
0.95
1.25
1.45
3.70
2.00
0.85
1.05
1.35
3.00
1.70
1206
3216
1.60
1.65
1.90
5.90
2.90
1.50
1.45
1.80
5.00
2.30
1.40
1.25
1.70
4.30
2.00
1210
3225
1.60
1.65
2.80
5.90
3.80
1.50
1.45
2.70
5.00
3.20
1.40
1.25
2.60
4.30
2.90
1808
4520
2.25
1.85
2.30
7.40
3.30
2.15
1.65
2.20
6.50
2.70
2.05
1.45
2.10
5.80
2.40
1812
4532
2.10
1.80
3.60
7.00
4.60
2.00
1.60
3.50
6.10
4.00
1.90
1.40
3.40
5.40
3.70
1825
4564
2.15
1.80
6.90
7.10
7.90
2.05
1.60
6.80
6.20
7.30
1.95
1.40
6.70
5.50
7.00
2220
5650
2.85
2.10
5.50
8.80
6.50
2.75
1.90
5.40
7.90
5.90
2.65
1.70
5.30
7.20
5.60
2225
5664
2.85
2.10
6.90
8.80
7.90
2.75
1.90
6.80
7.90
7.30
2.65
1.70
6.70
7.20
7.00
Density Level A: For low-density Product applications. Recommended for wave solder applications and provides a wider process window for reflow solder
processes. KEMET only recommends wave soldering of EIA 0603, 0805 and 1206 case sizes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC standard 7351 (IPC-7351).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
7
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Table 4 – Performance & Reliability: Test Methods and Conditions
Stress
Reference
Ripple Current
"Heat Generation
∆T : 20ºC max."
Test or Inspection Method
Terminal Strength
JIS-C-6429
Appendix 1, Note: Force of 1.8kg for 60 seconds.
Board Flex
JIS-C-6429
Appendix 2, Note: 2mm (min) for all except 3mm for C0G.
"Reflow solder the capacitor onto a PC board and apply voltage with 10kHz~1Mhz sine curve.
(Ripple voltage must be < rated voltage)"
Magnification 50X. Conditions:
Solderability
J-STD-002
a) Method B, 4 hrs @ 155°C, dry heat @ 235°C
b) Method B @ 215°C category 3
c) Method D, category 3 @ 260°C
Temperature Cycling
JESD22 Method JA-104
1000 Cycles (-55°C to +125°C), Measurement at 24 hrs. +/- 2 hrs after test conclusion.
Load Humidity: 1000 hours 85°C/85%RH and 300VDC Max. Add 100K ohm resistor. Measurement
at 24 hrs. +/- 2 hrs after test conclusion.
Low Volt Humidity: 1000 hours 85C°/85%RH and 1.5V. Add 100K ohm resistor. Measurement at
24 hrs. +/- 2 hrs after test conclusion.
t = 24 hours/cycle. Steps 7a & 7b not required. Unpowered. Measurement at 24 hrs. +/- 2 hrs after
test conclusion.
-55°C/+125°C. Note: Number of cycles required-300, Maximum transfer time-20 seconds, Dwell
time-15 minutes. Air-Air.
Biased Humidity
MIL-STD-202 Method 103
Moisture Resistance
MIL-STD-202 Method 106
Thermal Shock
MIL-STD-202 Method 107
High Temperature Life
MIL-STD-202 Method 108
1000 hours at 125°C (85°C for X5R, Z5U and Y5V) with rated voltage applied.
Storage Life
MIL-STD-202 Method 108
150°C, 0VDC, for 1000 Hours.
Mechanical Shock
MIL-STD-202 Method 213
Figure 1 of Method 213, Condition F.
Resistance to Solvents
MIL-STD-202 Method 215
Add Aqueous wash chemical - OKEM Clean or equivalent.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
8
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Tape & Reel Packaging Information
KEMET offers Multilayer Ceramic Chip Capacitors packaged in
8mm, 12mm and 16mm tape on 7" and 13" reels in accordance
with EIA standard 481. This packaging system is compatible with
all tape fed automatic pick and place systems. See Table 2 for
details on reeling quantities for commercial chips.
Bar Code Label
Anti-Static Reel
®
Embossed Plastic* or
Punched Paper Carrier.
T
ME
KE
Chip and KPS Orientation in Pocket
(except 1825 Commercial, and 1825 & 2225 Military)
Sprocket Holes
Embossment or Punched Cavity
8mm, 12mm
or 16mm Carrier Tape
178mm (7.00")
or
330mm (13.00")
Anti-Static Cover Tape
(.10mm (.004") Max Thickness)
*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.
Table 5 – Carrier Tape Configuration (mm)
EIA Case Size
Tape size (W)*
Pitch (P1)*
01005 - 0402
8
2
0603 - 1210
8
4
1805 - 1808
12
4
≥ 1812
12
8
KPS 1210
12
8
KPS 1812 & 2220
16
12
Array 0508 & 0612
8
4
*Refer to Figure 1 for W and P1 carrier tape reference locations.
*Refer to Table 6 for tolerance specifications.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
9
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
P2
T
T2
ØDo
Po
[10 pitches cumulative
tolerance on tape ±0.2 mm]
E1
Ao
F
Ko
B1
E2
Bo
S1
W
P1
T1
Center Lines of Cavity
ØD 1
Cover Tape
B 1 is for tape feeder reference only,
including draft concentric about B o.
Embossment
For cavity size,
see Note 1 Table 6
User Direction of Unreeling
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
D0
8mm
12mm
1.5 +0.10/-0.0
(0.059 +0.004/-0.0)
16mm
D1 Min.
Note 1
1.0
(0.039)
1.5
(0.059)
E1
P0
P2
1.75 ± 0.10
(0.069 ± 0.004)
4.0 ± 0.10
(0.157 ± 0.004)
2.0 ± 0.05
(0.079 ± 0.002)
R Ref.
Note 2
25.0
(0.984)
30
(1.181)
S1 Min.
Note 3
T Max.
T1 Max.
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
Variable Dimensions — Millimeters (Inches)
Tape Size
Pitch
8mm
Single (4mm)
12mm
Single (4mm) &
Double (8mm)
16mm
Triple (12mm)
B1 Max.
Note 4
4.35
(0.171)
8.2
(0.323)
12.1
(0.476)
E2 Min.
F
P1
T2 Max
W Max
A0,B0 & K0
6.25
(0.246)
10.25
(0.404)
14.25
(0.561)
3.5 ± 0.05
(0.138 ± 0.002)
5.5 ± 0.05
(0.217 ± 0.002)
5.5 ± 0.05
(0.217 ± 0.002)
4.0 ± 0.10
(0.157 ± 0.004)
8.0 ± 0.10
(0.315 ± 0.004)
8.0 ± 0.10
(0.315 ± 0.004)
2.5
(0.098)
4.6
(0.181)
4.6
(0.181)
8.3
(0.327)
12.3
(0.484)
16.3
(0.642)
Note 5
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 5).
3. If S1<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4).
(e) for KPS Series product A0 and B0 are measured on a plane 0.3mm above the bottom of the pocket.
(f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
10
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Figure 2 – Punched (Paper) Carrier Tape Dimensions
P2
T
Po
ØDo
[10 pitches cumulative
tolerance on tape ±0.2 mm]
A0
F
P1
T1
T1
Top Cover Tape
W
E2
B0
Bottom Cover Tape
E1
G
Cavity Size,
See
Note 1, Table 7
Center Lines of Cavity
Bottom Cover Tape
User Direction of Unreeling
Table 7 – Punched (Paper) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
D0
E1
P0
P2
T1Max
G Min
8mm
1.5 +0.10-0.0
(0.059 +0.004, -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
0.10
(.004) Max.
0.75
(.030)
R Ref.
Note 2
25
(.984)
T Max
W Max
A0 B 0
1.1
(0.098)
8.3
(0.327)
8.3
(0.327)
Variable Dimensions — Millimeters (Inches)
Tape Size
Pitch
8mm
Half (2mm)
8mm
Single (4mm)
E2 Min
6.25
(0.246)
F
3.5 ± 0.05
(0.138 ± 0.002)
P1
2.0 ± 0.05
(0.079 ± 0.002)
4.0 ± 0.10
(0.157 ± 0.004)
Note 5
1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that:
a) the component does not protrude beyond either surface of the carrier tape.
b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).
e) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
2. The tape with or without components shall pass around R without damage (see Figure 5).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
11
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg Minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
Peel Strength
8mm
12mm & 16mm
0.1 Newton to 1.0 Newton (10g to 100g)
0.1 Newton to 1.3 Newton (10g to 130g)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180° from the plane of the
carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556 and EIA-624.
Figure 3 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Width (mm)
8,12
16-200
Bo
Maximum
Rotation (
20
10
°
T)
Typical Component Centerline
Ao
°
s
Tape
Width (mm)
8,12
16-56
72-200
Maximum
Rotation (
20
10
5
°
S)
Figure 4 – Maximum Lateral Movement
8mm & 12mm Tape
16mm Tape
0.5 mm maximum
0.5 mm maximum
1.0 mm maximum
1.0 mm maximum
Figure 5 – Bending Radius
Embossed
Carrier
R
Punched
Carrier
Bending
Radius
R
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
12
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Figure 6 – Reel Dimensions
Full Radius,
See Note
W3 (Includes
Access Hole at
Slot Location
(Ø 40 mm min.)
flange distortion
at outer edge)
W2 (Measured at hub)
D
A
(See Note)
N
C
(Arbor hole
diameter)
B
(see Note)
W1 (Measured at hub)
If present,
tape slot in core
for tape start:
2.5 mm min. width x
10.0 mm min. depth
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 8 – Reel Dimensions
Metric Dimensions Will Govern
Constant Dimensions — Millimeters (Inches)
Tape Size
A
B Min
C
D Min
8mm
178 ± 0.20
(7.008 ± 0.008)
or
330 ± 0.20
(13.000 ± 0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12mm
16mm
Variable Dimensions — Millimeters (Inches)
Tape Size
N Min
8mm
12mm
16mm
50
(1.969)
W1
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
12.4 +2.0/-0.0
(0.488 +0.078/-0.0)
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
W2 Max
14.4
(0.567)
18.4
(0.724)
22.4
(0.882)
W3
Shall accommodate tape width
without interference
C1025-1 • 9/13/2010
13
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Figure 7 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Punched Carrier
8 mm & 12 mm only
Round Sprocket Holes
END
START
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
Trailer
160 mm minimum,
Components
100 mm Min.
Leader
400 mm Minimum,
Top Cover Tape
Figure 8 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm maximum, either direction
Straight Edge
250 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
14
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Figure 9 – Bulk Cassette Packaging (Ceramic Chips Only)
Meets Dimensional Requirements IEC-286 and EIAJ 7201
6 8 ± 0.1
8 8 ± 0.1
12.0 ± 0.1
Unit mm *Reference
19.0*
36 ± 00.2
31.5 ± 0.2
0
53 3*
10*
1.5 ±
2.0 ±
3.0 ±
0.1
0
0
0.1
0.2
0
5 0*
110 ± 0.7
Table 9 – Capacitor Dimensions for Bulk Cassette
Cassette Packaging – Millimeters
EIA Size Metric Size
L Length
Code
Code
W Width
B Bandwidth
S Separation
minimum
T Thickness
Number of
Pcs/Cassette
0402
1005
1.0 ± 0.05
0.5 ± 0.05
0.2 to 0.4
0.3
0.5 ± .05
50,000
0603
1608
1.6 ± 0.07
0.8 ± 0.07
0.2 to 0.5
0.7
0.8 ± .07
15,000
Table 10 – Capacitor Marking
Laser marking is available as an extra-cost option for most KEMET ceramic chips. Such marking is two sided, and includes a K to
identify KEMET, followed by two characters (per EIA-198) to identify the capacitance value. Note that marking is not available for any
Y5V chip. ln addition, the 0603 marking option is limited to the K only. (Marking Optional – Not Available for 0402 Size)
Numeral
Alpha
Character
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
Y
Z
a
b
d
e
f
m
n
t
y
Capacitance (pF) For Various Numeral Identifiers
9
0.1
0.11
0.12
0.13
0.15
0.16
0.18
0.2
0.22
0.24
0.27
0.3
0.33
0.36
0.39
0.43
0.47
0.51
0.56
0.62
0.68
0.75
0.82
0.91
0.25
0.35
0.4
0.45
0.5
0.6
0.7
0.8
0.9
0
1
1.1
1.2
1.3
1.5
1.6
1.8
2
2.2
2.4
2.7
3
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
2.5
3.5
4
4.5
5
6
7
8
9
1
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
25
35
40
45
50
60
70
80
90
2
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
250
350
400
450
500
600
700
800
900
3
1000
1100
1200
1300
1500
1600
1800
2000
2200
2400
2700
3000
3300
3600
3900
4300
4700
5100
5600
6200
6800
7500
8200
9100
2500
3500
4000
4500
5000
6000
7000
8000
9000
4
10000
11000
12000
13000
15000
16000
18000
20000
22000
24000
27000
30000
33000
36000
39000
43000
47000
51000
56000
62000
68000
75000
82000
91000
25000
35000
40000
45000
50000
60000
70000
80000
90000
5
100000
110000
120000
130000
150000
160000
180000
200000
220000
240000
270000
300000
330000
360000
390000
430000
470000
510000
560000
620000
680000
750000
820000
910000
250000
350000
400000
450000
500000
600000
700000
800000
900000
6
1000000
1100000
1200000
1300000
1500000
1600000
1800000
2000000
2200000
2400000
2700000
3000000
3300000
3600000
3900000
4300000
4700000
5100000
5600000
6200000
6800000
7500000
8200000
9100000
2500000
3500000
4000000
4500000
5000000
6000000
7000000
8000000
9000000
7
10000000
11000000
12000000
13000000
15000000
16000000
18000000
20000000
22000000
24000000
27000000
30000000
33000000
36000000
39000000
43000000
47000000
51000000
56000000
62000000
68000000
75000000
82000000
91000000
25000000
35000000
40000000
45000000
50000000
60000000
70000000
80000000
90000000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Example shown is 1,000 pF capacitor
C1025-1 • 9/13/2010
15
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Other KEMET Resources
Tools
Resource
Location
Configure A Part: CapEdge
http://capacitoredge.kemet.com
SPICE & FIT Software
http://www.kemet.com/spice
Search Our FAQs: KnowledgeEdge
http://www.kemet.com/keask
Product Information
Resource
Location
Products
Technical Resources (Including Soldering
Techniques)
RoHS Statement
Quality Documents
http://www.kemet.com/products
http://www.kemet.com/technicalpapers
http://www.kemet.com/rohs
http://www.kemet.com/qualitydocuments
Product Request
Resource
Location
Sample Request
Engineering Kit Request
http://www.kemet.com/sample
http://www.kemet.com/kits
Contact
Resource
Location
Website
Contact Us
Investor Relations
www.kemet.com
http://www.kemet.com/contact
http://www.kemet.com/ir
Call Us
1-877-MyKEMET
Twitter
http://twitter.com/kemetcapacitors
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) are subject to change without notice.
All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we
specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite
experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the
use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.
Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur.
Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or
redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
16
SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
KEMET Corporation
World Headquarters
P.O. Box 5928
Greenville, SC 29606
2835 KEMET Way
Simpsonville, SC 29681
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
North America
Corporate Offices
101 NE Third Avenue
Tower 101, Suite 1700
Fort Lauderdale, FL 33301
Tel: 954-766-2800
Fax: 954-766-2805
Southeast
801 International Parkway, Suite 5070
Lake Mary, FL 32746
Tel: 407-855-8886
Northeast
340-X Fordham Road
Wilmington, MA 01887
Tel: 978-658-1663
Fax: 978-658-1790
Central
1900 North Roselle Road, Suite 405
Schaumburg, IL 60195
Tel: 847-882-3590
Fax: 847-882-3046
Europe
Southern Europe
15bis chemin des Mines, 4th floor
1202 Geneva
Switzerland
Tel: 41-22-715-0100
Fax: 41-22-715-0170
Zac Paris Rive Gauche
118-122 avenue de France
75013 Paris
France
Tel: 33-1-4646-1009
Fax: 33-1-4646-1599
Via San Lorenzo 19
Sasso Marconi, BO
40037
Italy
Tel: 39-051-939111
Fax: 39-051-840684
Viale Milanofiori 1
Palazzo E1
20090 Assago
Milano
Italy
Tel: 39-02-57518176
Fax: 39-02-57512093
Central Europe
Hermann-Koehl-Str. 2
Landsberg am Lech
86899 Germany
Tel: 49-8191-3350800
Fax: 49-8191-3350990
West
1551 McCarthy Boulevard, Suite 117
Milpitas, CA 95035
Tel: 408-433-9946
Fax: 408-433-9946
Ruhrallee 9
Dortmund
44139 Germany
Tel: 49-2307-3619672
Fax: 49-2307-961527
Mexico
Northern Europe
Tezozomoc No. 47
Col. Ciudad del Sol
Zapopan, Jalisco C.P. 45050
Mexico
Tel: 52-33-3123-2141
Fax: 52-33-3123-2144
Unit 1, Ducketts Wharf
South Street
Bishops Stortford
Hertfordshire CM23 3AL
United Kingdom
Tel: 44-1279-757201
Fax: 44-1279-465237
20-21 Cumberland Drive
Granby Industrial Estate
Weymouth, Dorset DT4 9TE
United Kingdom
Tel: 44-1305-830747
Fax: 44-1305-760670
Room 305, Floor 3, #142
Sec. 4, Chung Hsiao East Road
Taipei 106
Taiwan ROC
Tel: 886-2-27528585
Fax: 886-2-27213129
Thörnblads Väg 6
Färjestaden 386 90
Sweden
Tel: 46-485-563934
Fax: 46-485-563938
Southeast Asia
Stella Business Park
Lars Sonckin kaari 16
Espoo 02600
Finland
Tel: 358-9-5406-5000
Fax: 358-9-5406-5010
Asia
Northeast Asia
30 Canton Road, Room 1512
Silvercord Tower II
Tsimshatshui, Kowloon
Hong Kong
Tel: 852-2305-1168
Fax: 852-2759-0345
73 Bukit Timah Road
#05-01 Rex House
229832 Singapore
Tel: 65-6586-1900
Fax: 65-6586-1901
1-5-20 Krystal Point 2
Lebuh Bukit Kecil 6
11900 Bayan Baru
Penang
Malaysia
Tel: 6- 04-6430200
Fax: 6 -04-6444220
Office No. 605, 6th Floor
Barton Centre M.G. Road
Bangalore 560 001
India
Tel: 91-80-653-76817
Fax: 91-80-2532-0160
Room 1411, 14/F New China
Insurance Edifice
Mintian Road, CBD Futian District
Shenzhen 518001
China
Tel: 1-867-55-25181306
Fax: 1-867-55-25181307
Floor 17, Tower B, Ping An IFC
No.1-3 Xin Yuan South Road
Chao Yang District
Beijing 100027
China
Tel: 86-10-5829-1711
Fax: 86-10-5829-1963
Room 2602, Grand Gateway Tower 1
No.1 Hong Qiao Road
Shanghai 200030
China
Tel: 86-21-6447-0707
Fax: 86-21-6447-0070
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1025-1 • 9/13/2010
17