94SVPD www.vishay.com Vishay OS-CON SMD Aluminum Solid Capacitors with Conductive Polymer FEATURES • New OS-CON 94SVPD series provides improved characteristics with up to 125 °C temperature capability and 35 V maximum voltage rating in a SMD package • Improved damp heat (steady state) 85 °C x 85 % RH performance • Suitable for use in smoothing circuits of vehicle-mounted equipment, industrial equipment, etc. • This product can support lead (Pb)-free reflow (2) • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 QUICK REFERENCE DATA DESCRIPTION Operating temperature range Capacitance tolerance Tangent of loss angle (tan ) Leakage current (μA/2 min) (or less) (1) ESR Characteristics of impedance ratio at high and low temperature CONDITIONS 120 Hz 120 Hz After 2 min - VALUE - 55 °C to + 125 °C M: ± 20 % values in Electrical Data and Ordering Information table values in Electrical Data and Ordering Information table values in Electrical Data and Ordering Information table - 55 °C Z/Z20 °C 0.75 to 1.25 + 125 °C Z/Z20 °C 0.75 to 1.0 C/C Within ± 20 % tan 2 x or < than an initial standard ESR 2 x or < than an initial standard Leakage current Below an initial standard C/C Within ± 20 % tan 2 x or < than an initial standard ESR 2 x or < than an initial standard Leakage current Below an initial standard C/C Within ± 10 % tan 1.3 x or < than an initial standard ESR 1.3 x or < than an initial standard Below an initial standard Leakage current (after voltage procesing) 100 kHz, + 20 °C + 125 °C, 2000 h rated voltage applied Endurance Damp heat (steady state) + 85 °C, 85 % to 90 % RH, 1000 h rated voltage applied Solder heat resistance (2) (VPS) (230 °C x 75 s) Notes (1) If any doubt arises, measure the current after applying voltage (voltage treatment). Voltage treatment: The rated voltage is applied (10 V to 35 V) for 120 min at 125 ºC. (2) Refer to “Recommended Reflow Profile” for maximum temperatures. DIMENSIONS in millimeters 0.2 max. L SIZE CODE C6 E7 F8 E12 F12 Revision: 03-Aug-12 Ø D ± 0.5 6.3 8.0 10.0 8.0 10.0 L + 0.1/- 0.4 5.9 6.9 7.9 11.9 12.6 W ± 0.2 6.6 8.3 10.3 8.3 10.3 H ± 0.2 6.6 8.3 10.3 8.3 10.3 W P C H ØD Series C6 size is PD E7, F8, E12, F12 size is SVPD Polarity marking (Cathode) Case No. 003 SVPD Rated capacitance 47 35 Rated voltage R C ± 0.2 7.3 9.0 11.0 9.0 11.0 (+) R 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.8 to 1.1 0.8 to 1.1 P ± 0.2 2.1 3.2 4.6 3.2 4.6 Document Number: 90022 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON CASE CODE LIST RATED VOLTAGE (SURGE AT 125 °C) CAPACITANCE (μF) 10.0 (11.5) 16.0 (18.4) 25.0 (29.0) 35.0 (40.0) 8.2 E7 10 C6 18 F8 22 E7 39 F8 47 E12 56 E12 F12 C6 82 E7 F12 RECOMMENDED LAND PATTERN DIMENSIONS (in millimeters) SIZE CODE a b c C6 2.1 9.1 1.6 E7 2.8 11.1 1.9 a F8 4.3 13.1 1.9 b E12 2.8 11.1 1.9 F12 4.3 13.1 1.9 c FREQUENCY COEFFICIENT FOR RIPPLE CURRENT FREQUENCY 120 Hz f < 1 kHz 1 kHz f < 10 kHz 10 kHz f < 100 kHz 100 kHz f < 500 kHz COEFFICIENT 0.05 0.3 0.7 1 ELECTRICAL DATA AND ORDERING INFORMATION UR (V) CR (μF) CASE CODE MAX. ESR (100 kHz TO 300 kHz) (m) RATED RIPPLE CURRENT 105 °C < Tx 125 °C ALLOWABLE RIPPLE CURRENT MAX. LEAKAGE CURRENT (μA) (2) PART NUMBER (1) Tx 105 °C MAX. TANGENT OF LOSS ANGLE 94SVPD566X0010C6 100 kHz (mA) (3) 10 56 C6 45 538 1700 0.12 112 16 82 E7 40 670 2120 0.12 262 94SVPD826X0016E7 10 C6 65 474 1500 0.10 50 94SVPD106X0025C6 22 E7 48 580 1835 0.10 110 94SVPD226X0025E7 39 F8 45 664 2100 0.10 195 94SVPD396X0025F8 47 E12 30 943 2980 0.12 235 94SVPD476X0025E12 82 F12 28 1202 3800 0.12 410 94SVPD826X0025F12 8.2 E7 70 400 1300 0.10 57 94SVPD825X0035E7 18 F8 60 550 1800 0.10 126 94SVPD186X0035F8 22 E12 50 700 2300 0.12 154 94SVPD226X0035E12 47 F12 30 1150 3650 0.12 329 94SVPD476X0035F12 25 35 Notes (1) Capacitance tolerance: M ± 20 % (2) After 2 min (3) Tx: Ambient temperature Revision: 03-Aug-12 Document Number: 90022 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON FREQUENCY CHARACTERISTICS 1000 ESR, Impedance (Ω) 100 10 1 Curve 1: 94SVPD476X0035F12 Impedance (Ω) Curve 2: 94SVPD476X0035F12 ESR (Ω) Curve 3: 94SVPD186X0035F8 Impedance (Ω) Curve 4: 94SVPD186X0035F8 ESR (Ω) Curve 5: 94SVPD106X0025C6 Impedance (Ω) Curve 6: 94SVPD106X0025C6 ESR (Ω) Curve 7: 94SVPD826X0025F12 Impedance (Ω) Curve 8: 94SVPD826X0025F12 ESR (Ω) 5 3 1 7 4 6 2 8 0.1 0.01 0.001 0.1 1 100 10 1000 10 000 Frequency (kHz) FREQUENCY (kHz) 0.12 0.5 1 10 100 500 1000 5000 10 000 94SVPD106X0025C6 IMPEDANCE () 127.769 31.001 15.608 1.612 0.176 0.046 0.032 0.093 0.179 94SVPD106X0025C6 ESR () 1.303 0.482 0.306 0.081 0.044 0.035 0.032 0.033 0.040 94SVPD186X0035F8 IMPEDANCE () 72.87 17.781 8.955 0.918 0.096 0.023 0.037 0.200 0.397 94SVPD186X0035F8 ESR () 1.681 0.333 0.179 0.043 0.027 0.023 0.023 0.026 0.034 94SVPD476X0035F12 IMPEDANCE () 30.178 7.389 3.725 0.392 0.05 0.016 0.025 0.134 0.266 94SVPD476X0035F12 ESR () 0.852 0.206 0.121 0.045 0.023 0.016 0.014 0.017 0.023 94SVPD826X0025F12 IMPEDANCE () 16.736 4.096 2.074 0.229 0.029 0.014 0.028 0.144 0.285 94SVPD826X0025F12 ESR () 0.339 0.135 0.094 0.033 0.015 0.011 0.011 0.014 0.019 Revision: 03-Aug-12 Document Number: 90022 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD106X0025C6 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE LOT. NUMBER Endurance (after V.P.S. test) 125 °C 25 V 7130A2714 Change in capacitance (120 Hz) Tangent of loss angle (120 Hz) 20 0.12 0.11 10 0.10 Tangent of loss angle Max. Δ (%) 0 Av. Min. - 10 - 20 - 30 0.09 0.08 0.07 0.06 0.05 0.04 0.03 Av. 0.02 Max. 0.01 - 40 Min. 0 0 2000 Time (h) 0 2000 Time (h) Leakage current (25 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 ESR (mΩ) 140 120 100 80 Av. 60 40 Max. Min. Leakage current (µA) 160 100 10 Max. 1 Av. 0.1 20 Min. 0 0.01 0 TIME (h) 2000 0 Time (h) 2000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD186X0035F8 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE LOT. NUMBER Endurance (after V.P.S. test) 125 °C 35 V 6517A3254 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 0.10 Av. Δ (%) 0 Max. Min. - 10 - 20 Tangent of loss angle 10 - 30 0.09 0.08 0.07 0.06 0.05 0.04 Av. 0.03 Max. 0.02 0.01 Min. 0 - 40 0 2000 Time (h) 0 2000 Time (h) Leakage current (35 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 Leakage current (µA) 160 ESR (mΩ) 140 120 100 80 60 Av. 40 Max. 100 10 Av. 0.1 20 Max. 1 Min. Min. 0 0.01 0 Time (h) 2000 0 Time (h) 2000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD476X0035F12 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE LOT. NUMBER Endurance (after V.P.S. test) 125 °C 35 V 7209A6544 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 0.10 10 Max. Δ (%) 0 Min. - 10 - 20 Tangent of loss angle Av. - 30 0.09 0.08 0.07 0.06 0.05 0.04 Av. 0.03 Max. 0.02 0.01 Min. 0 - 40 0 2000 Time (h) 0 2000 Time (h) Leakage current (35 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 Leakage current (µA) 160 ESR (mΩ) 140 120 100 80 Av. 60 Max. 40 100 Av. 10 Max. 1 Min. 0.1 20 Min. 0 0.01 0 Time (h) 2000 0 Time (h) 2000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD826X0025F12 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE LOT. NUMBER Endurance (after V.P.S. test) 125 °C 25 V 7527A6544 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 0.10 10 Tangent of loss angle Max. Δ (%) 0 Av. - 10 Min. - 20 - 30 0.09 0.08 0.07 0.06 Max. 0.05 0.04 Av. 0.03 0.02 0.01 Min. 0 - 40 0 2000 Time (h) 0 2000 Time (h) Leakage current (25 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 160 Leakage current (µA) ESR (mΩ) 140 120 100 80 60 Av. 40 Max. 100 Max. Av. 10 1 Min. 0.1 20 Min. 0 0 Time (h) 0.01 2000 0 Time (h) 2000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD106X0025C6 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE TEST HUMIDITY LOT. NUMBER Damp heat (steady state) (after V.P.S. test) 85 °C 25 V 85 % 7530A2714 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 0.10 10 Max. 0 Δ (%) Tangent of loss angle Av. Min. - 10 - 20 - 30 0.09 0.08 0.07 0.06 0.05 Av. 0.04 Max. 0.03 Min. 0.02 0.01 0 - 40 0 Time (h) 1000 0 1000 Time (h) Leakage current (25 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 ESR (mΩ) 140 120 100 Av. Max. 80 60 Leakage current (µA) 160 100 10 Av. 1 Max. Min. 40 0.1 20 0 Min. 0.01 0 Time (h) 1000 0 Time (h) 1000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD186X0035F8 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE TEST HUMIDITY LOT. NUMBER Damp heat (steady state) (after V.P.S. test) 85 °C 35 V 85 % 6517A3254 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 Av. 0.10 Max. Tangent of loss angle 10 0 Δ (%) Min. - 10 - 20 - 30 0.09 0.08 Av. Max. 0.07 0.06 0.05 Min. 0.04 0.03 0.02 0.01 0 - 40 0 1000 Time (h) 0 1000 Time (h) Leakage current (35 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 Leakage current (µA) 160 ESR (mΩ) 140 120 100 80 Av. 60 Max. 40 100 Av. 10 Max. 1 0.1 20 Min. Min. 0 0.01 0 Time (h) 1000 0 Time (h) 1000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD476X0035F12 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE TEST HUMIDITY LOT. NUMBER Damp heat (steady state) (after V.P.S. test) 85 °C 35 V 85 % 7209A6544 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 0 Δ (%) 0.10 Max. Av. Tangent of loss angle 10 Min. - 10 - 20 - 30 0.09 0.08 0.07 0.06 Max. Av. 0.05 0.04 0.03 Min. 0.02 0.01 0 - 40 0 1000 Time (h) 0 1000 Time (h) Leakage current (35 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 Leakage current (µA) 160 ESR (mΩ) 140 120 100 80 60 Av. 100 Av. Max. 10 1 Max. 40 Min. 0.1 20 Min. 0 0.01 0 Time (h) 1000 0 Time (h) 1000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON TYPICAL PARAMETERS MODEL 94SVPD826X0025F12 TEST ITEM TEST TEMPERATURE APPLIED VOLTAGE TEST HUMIDITY LOT. NUMBER Damp heat (steady state) (after V.P.S. test) 85 °C 25 V 85 % 6806A6724 Tangent of loss angle (120 Hz) Change in capacitance (120 Hz) 0.12 20 0.11 0.10 10 Max. Tangent of loss angle Av. Δ (%) 0 Min. - 10 - 20 - 30 0.09 0.08 0.07 0.06 Max. 0.05 0.04 Av. 0.03 0.02 Min. 0.01 0 - 40 0 1000 Time (h) 0 1000 Time (h) Leakage current (25 V, 60 s) ESR (100 kHz) 200 10 000 180 1000 Leakage current (µA) 160 ESR (mΩ) 140 120 100 80 60 Av. 40 Max. 100 Av. 10 Max. 1 0.1 Min. 20 Min. 0 0 Time (h) 0.01 1000 0 Time (h) 1000 Notes • n = 30 pieces • V.P.S. test conditions: 230 °C x 75 s x 2 (V.P.S. = Vapor Phase Soldering method) Revision: 03-Aug-12 Document Number: 90022 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 94SVPD www.vishay.com Vishay OS-CON Surface of external case/terminal (°C) RECOMMENDED REFLOW PROFILE 300 Peak temperature 250 Duration at 230 °C or higher Duration at 220 °C or higher Duration at 200 °C or higher 200 150 100 Preheating 150 °C to 180 °C 50 0 0 30 60 90 120 150 180 210 240 Vishay OS-CON has different characteristics against soldering heat from conventional aluminum electrolytic capacitors or tantalum capacitors because of its unique materials and structure. Please note the following points on soldering of Vishay OS-CON 94SVPD series to draw out the best performance. ITEM Peak temperature (max.) 94SVPD SERIES 250 °C Preheat 260 °C 150 °C to 180 °C 90 ± 30 s 200 °C over time (max.) 60 s 60 s 220 °C over time (max.) 50 s 50 s 230 °C over time (max.) 40 s 40 s Twice or less Only 1 time Reflow number Note • All temperatures are measured on the topside of the Al-can and terminal surface. Attention: Reflow soldering may reduce the capacitance of products before or after soldering even if soldering conditions stipulated in Recommended Reflow Condition are met. Though the actual reflow conditions are subject to change depending on the kind of reflow soldering method, please be aware that the peak temperature at the top of Al-case and electrode terminals should not exceed peak temperature. Particular notice should be given to the time that Vishay OS-CON is heated at 200 °C or higher during reflow. Be aware that soldering considerably deviating from these conditions will cause problems such as a 50 % reduction in capacitance, and a considerable increase in leakage current. The leakage current value may increase (from a few μA to a few mA) even within the above conditions. When the Vishay OS-CON is used in a DC circuit, the leakage current will decrease gradually through self-recovery after voltage is applied. If your reflow profile (reflow temperature, number of reflows, etc.) deviates from the above conditions for mounting the 94SVPD series, please consult with Vishay OS-CON. Revision: 03-Aug-12 Document Number: 90022 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000