TetraFET D5030UK ROHS COMPLIANT METAL GATE RF SILICON FET MECHANICAL DATA B C (2 pls) 2 G (typ) 3 1 H P (2 pls) A D 4 5 GOLD METALLISED MULTI-PURPOSE SILICON DMOS RF FET 400W – 50V – 175MHz PUSH–PULL E (4 pls) F I FEATURES • SIMPLIFIED AMPLIFIER DESIGN N O M J K • SUITABLE FOR BROAD BAND APPLICATIONS DR PIN 1 PIN 3 PIN 5 SOURCE (COMMON) DRAIN 2 GATE 1 DIM A B C D E F G H I J K M N O P Millimetres 19.05 10.77 45° 9.78 5.71 27.94 1.52R 10.16 22.22 0.13 2.72 1.70 5.08 34.03 1.61R PIN 2 PIN 4 DRAIN 1 GATE 2 • LOW Crss • SIMPLE BIAS CIRCUITS Tol. 0.50 0.13 5° 0.13 0.13 0.13 0.13 0.13 MAX 0.02 0.13 0.13 0.50 0.13 0.08 Inches 0.75 0.424 45° 0.385 0.225 1.100 0.060R 0.400 0.875 0.005 0.107 0.067 0.200 1.340 0.064R Tol. 0.020 0.005 5° 0.005 0.005 0.005 0.005 0.005 MAX 0.001 0.005 0.005 0.020 0.005 0.003 • LOW NOISE • HIGH GAIN – 16 dB MINIMUM APPLICATIONS • VHF/UHF COMMUNICATIONS from 1 MHz to 250 MHz ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated) PD BVDSS BVGSS ID(sat) Tstg Tj Power Dissipation Drain – Source Breakdown Voltage* Gate – Source Breakdown Voltage* Drain Current* Storage Temperature Maximum Operating Junction Temperature 583W 125V ±20V 24A –65 to 150°C 200°C * per side Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. Website: http://www.semelab.co.uk E-mail: [email protected] Document Number 6581 Issue 3 D5030UK ELECTRICAL CHARACTERISTICS (Tcase = 25°C unless otherwise stated) Parameter Test Conditions Min. Typ. Max. Unit PER SIDE BVDSS IDSS Drain–Source Breakdown Voltage Zero Gate Voltage Drain Current ID = 100mA VDS = 50V VGS = 0 8 mA 1 μA 7 V IGSS Gate Leakage Current VGS = 20V VDS = 0 VGS(th) Gate Threshold Voltage* ID = 10mA VDS = VGS gfs Forward Transconductance* VDS = 10V ID = 8A ID = 10mA VDS = VGS VGS(th)match Gate Threshold Voltage Matching Between Sides V VGS = 0 125 1 mhos 6.4 0.1 V TOTAL DEVICE GPS Common Source Power Gain PO = 400W η Drain Efficiency VDS = 50V VSWR Load Mismatch Tolerance f = 175MHz Ciss Input Capacitance VDS = 50V VGS = –5V f = 1MHz 480 pF Coss Output Capacitance VDS = 50V VGS = 0 f = 1MHz 200 pF Crss Reverse Transfer Capacitance VDS = 50V VGS = 0 f = 1MHz 12 pF IDQ = 2A 16 dB 50 % 20:1 — PER SIDE * Pulse Test: Pulse Duration = 300 μs , Duty Cycle ≤ 2% HAZARDOUS MATERIAL WARNING The ceramic portion of the device between leads and metal flange is beryllium oxide. Beryllium oxide dust is highly toxic and care must be taken during handling and mounting to avoid damage to this area. THESE DEVICES MUST NEVER BE THROWN AWAY WITH GENERAL INDUSTRIAL OR DOMESTIC WASTE. THERMAL DATA RTHj–case Thermal Resistance Junction – Case Max. 0.3°C / W Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. Website: http://www.semelab.co.uk E-mail: [email protected] Document Number 6581 Issue 3 D5030UK 25 70 60 Power added efficiency (%) Gain (dB) 20 15 10 F= 175MHz Idq= 2.0A Vds= 50V 5 50 40 30 20 0 0 50 100 150 200 250 300 350 400 F= 175MHz Idq= 2.0A Vds= 50V 10 0 450 0 50 100 150 200 Pout (W) 250 300 350 400 450 Pout (W) Figure 1 Figure 2 Gain vs. Output Power. Power added efficiency vs.Output Power 400 350 300 Pout(W) 250 200 150 100 F= 175MHz Idq= 2.0A Vds= 50V 50 0 0 0.5 1 1.5 2 2.5 3 pin (W) Figure 3 Output Power vs. Input Power. Typical S Parameters ! # VDS50V, IDQ = 1.4A MHz S MA R 50 !Freq !MHz S11 mag ang S21 mag ang S12 mag ang S22 mag ang 50 100 150 200 250 300 350 400 450 500 550 600 0.83 0.89 0.93 0.95 0.97 0.98 0.98 0.98 0.99 0.99 0.99 0.99 -165.3 -170 -173.2 -175.7 -177.8 -179.7 178.7 177.3 175.9 174.7 173.5 172.3 20.29 8.28 4.42 2.71 1.82 1.3 0.97 0.76 0.61 0.5 0.42 0.35 69.4 48.6 35.6 27.2 21.3 17 13.8 11.4 9.5 8.1 7.1 6.5 0.007 0.004 0.003 0.005 0.008 0.011 0.014 0.017 0.02 0.023 0.026 0.028 -9.2 -6 50 82.4 88.8 90 89.6 88.9 87.9 86.9 85.9 84.9 0.63 0.78 0.86 0.91 0.94 0.95 0.97 0.97 0.98 0.98 0.98 0.99 -150.7 -156.6 -162 -166.2 -169.4 -171.9 -174 -175.7 -177.3 -178.6 -179.8 179 Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. Website: http://www.semelab.co.uk E-mail: [email protected] Document Number 6581 Issue 3 D5030UK 24 22 20 2V Drain Current (A) 18 4V 16 6V 14 8V 12 10V 10 12V 8 6 4 2 0 0 5 10 15 20 25 30 35 40 45 50 Drain Voltage (V) Figure 5 – Typical IV Characteristics. Capacitance (pF) 1000 100 Output Capacitance Input Capacitance Reverse Transfer Capacitance 10 1 0 5 10 15 20 25 30 35 40 45 50 Drain-Source Voltage (V) Figure 6 – Typical CV Characteristics. Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. Website: http://www.semelab.co.uk E-mail: [email protected] Document Number 6581 Issue 3 D5030UK 50 5)LQ 0 0 6-60pF S) 0.1u X S) 5000p D5030UK '8. 1n Q)1.6k . L1 / D5030UK '8. 1n Q) 'UDLQ%LDV S) 47p S) 180p 1k . 0.1u X L2 / 0.47u X *DWH%LDV 5)RXW S) 6-60pF 1000p S) 5000p S) 0.1u X 0 0 7; 7; 50 7;WUDQVIRUPHUWXUQVRIVHPLULJLGFRD[DURXQGSRZGHUHGLURQFRUH 7;WUDQVIRUPHUWXUQVRIVHPLULJLGFRD[DURXQGSRZGHUHGLURQFRUH /WXUQVDZJHQDPHOOHGZLUHPPLQWHUQDOGLDPHWHU /WXUQVDZJHQDPHOOHGZLUHRQ$[KROHFRUH 0PLFURVWULSOLQHPPORQJPPZLGHRQLQWKLFN*VXEVWUDWH D5030UK 175MHz TEST FIXTURE Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. Website: http://www.semelab.co.uk E-mail: [email protected] Document Number 6581 Issue 3