ROHM LM4565F

Datasheet
Operational Amplifiers
Low Noise Operational Amplifier
LM4565F
●Key Specifications
 Wide Operating Voltage:
±4V to ±18V
 Wide Temperature Range:
-40°C to +85°C
 High voltage gain (RL=2kΩ):
100dB(Typ.)
 High Slew Rate:
5.0V/μs (Typ.)
 Wide Unity Gain Bandwidth:
10MHz (Typ.)
 Low Input Noise Voltage:
0.6µVrms (Typ.)
●General Description
BA4565 is dual operational amplifier with high gain and
wide bandwidth. It has good performance of input
referred noise voltage(5 nV/ Hz ) and total harmonic
distortion(0.002%). These are suitable for Audio
applications.
●Features
 Wide Operating Voltage
 High Voltage Gain
 Low distortion
 Wide Bandwidth
 High Slew Rate
 Low Noise Voltage
 Internal ESD protection
●Package
SOP8
W(Typ.) xD(Typ.) xH(Max.)
5.00mm x 6.20mm x 1.71mm
●Application
 Audio application
 General Purpose
●Block Diagram
VCC
－IN
OUT
VOUT
＋IN
VEE
Figure1. Simplified Schematic (1 channel only)
○Product structure：Silicon monolithic integrated circuit
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･14･001
○This product is not designed to be protected against radioactive rays.
1/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Pin Configuration
SOP8
OUT1 1
-IN1
2
+IN1
3
VEE
Pin No.
Symbol
1
OUT1
2
-IN1
7 OUT2
3
+IN1
6 -IN2
4
VEE
5
+IN2
6
-IN2
7
OUT2
8
VCC
8 VCC
CH1
- +
CH2
+ -
4
5 +IN2
●Ordering Information
L
M
4
5
6
Part Number
LM4565F
5
F
-
E2
Packaging and forming specification
E2: Embossed tape and reel
(SOP8)
Package
F:SOP8
●Line-up
Topr
-40°C to +85°C
Package
SOP8
Operable Part Number
Reel of 2500
LM4565F-E2
●Absolute Maximum Ratings(Ta=25°C)
Parameter
Supply Voltage
Symbol
Ratings
Unit
VCC - VEE
+36
V
Power Dissipation
Pd
690*1*2
mW
Differential Input Voltage*3
Input Common-mode
Voltage Range
Operating Voltage
Vid
+36
V
Vicm
(VEE - 0.3) to (VEE + 36)
V
Vopr
±4 to ±18
V
Operating Temperature
Topr
- 40 to +85
°C
Storage Temperature
Maximum
Junction Temperature
Tstg
- 55 to +150
°C
Tjmax
+150
°C
Note: Absolute maximum rating of each item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or usage out of absolute maximum rated
temperature environment may cause deterioration of characteristics.
*1
When used at temperature above Ta＝25°C, reduce by 5.52mW/°C.
*2
Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
*3
The differential input voltage is the voltage difference between inverting input and non-inverting input.
Input terminal voltage is set to more than VEE.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
2/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Electrical Characteristics:
○LM4565F (Unless otherwise specified VCC = +15V, VEE = -15V)
Parameter
Symbol
Limits
Temperature
Range
Min.
Typ.
Max.
Unit
Condition
Input Offset Voltage *4*5
Vio
25°C
-
0.5
1.5
mV
Input Offset Current *4
Iio
25°C
-
2
50
nA
-
Input Bias Current *4
Ib
25°C
-
70
250
nA
-
25°C
-
4.5
7
mA
RL=∞, All Op-Amps,
VIN+=0V
Supply Current
*5
ICC
Large Signal Voltage Gain
Av
Maximum Output Voltage
VOM
RS ≤10kΩ
Full range
-
-
8.5
25°C
86
100
-
dB
RL ≥2kΩ, OUT =±10V
25°C
±12
±14
-
V
RL ≥2kΩ
25°C
±11
±12.5
-
V
Io≥25mA
Input Common-mode Voltage Range
Vicm
25°C
±12
±14
-
V
Output Source Current*6
IOH
25°C
-
130
-
mA
Output Sink Current*6
IOL
25°C
-
160
-
mA
Common-mode Rejection Ratio
CMRR
25°C
80
100
-
dB
RL ≤10kΩ
Power Supply Rejection Ratio
PSRR
25°C
82
100
-
dB
RL ≤10kΩ
SR
25°C
-
5
-
V/μs
RL=2kΩ, CL=100pF
fT
25°C
MHz
RL=2kΩ
GBW
25°C
-
10
-
MHz
RL=2kΩ, f=100kHz
θ
25°C
-
40
-
deg
RL=2kΩ
-
0.6
-
µVrms
RIAA, RS=100Ω
DIN-AUDIO
-
5
-
nV/ Hz
Vicm=0V, f=1kHz
Slew Rate
Unity Gain Frequency
Gain Band Width
Phase Margin
Equivalent Input Noise Voltage
Total Harmonic Distortion+ Noise
Channel Separation
*4
*5
*6
Vn
4
VIN+=1V, VIN-=0V
OUT=-15V,
1CH is short circuit
VIN+=0V,VIN-=1V
OUT=+15V,
1CH is short circuit
25°C
THD+N
25°C
-
0.002
-
%
Av=20dB,
OUT=0.1Vrms,
f=1kHz
CS
25°C
-
110
-
dB
Av=40dB, RS=1kΩ
f=1kHz
Absolute value.
Full range: Ta=-40°C to +85°C
Please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
3/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
Description of electrical characteristics
Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown.
Note that item name, symbol and their meaning may differ from those on other manufacturer’s document or general
documents.
1. Absolute maximum ratings
Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute
maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.
1.1 Supply voltage (VCC - VEE)
Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power
supply terminal without deterioration or destruction of characteristics of internal circuit.
1.2 Differential input voltage (Vid)
Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without
deterioration and destruction of characteristics of IC.
1.3 Input common-mode voltage range (Vicm)
Indicates the maximum voltage that can be applied to the non-inverting terminal and inverting terminal without
deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assures
normal operation of IC. When normal Operation of IC is desired, the input common-mode voltage of characteristics
item must be followed.
1.4 Power dissipation (Pd)
Indicates the power that can be consumed by the IC when mounted on a specific board at ambient temperature 25°C(normal
temperature). As for packaged product, Pd is determined by the temperature that can be permitted by the IC in the
package (maximum junction temperature) and the thermal resistance of the package.
2. Electrical characteristics item
2.1 Input offset voltage (Vio)
Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the
input voltage difference required for setting the output voltage to 0 V.
2.2 Input offset current (Iio)
Indicates the difference of input bias current between non-inverting terminal and inverting terminal.
2.3 Input bias current (Ib)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at
the non-inverting and inverting terminals.
2.4 Supply current (ICC)
Indicates the current that flows within the IC under specified no-load conditions.
2.5 Large signal voltage gain (Av)
Indicates the amplification rate (gain) of output voltage against the voltage difference between non-inverting terminal
and inverting terminal. It is normally the amplification rate (gain) with reference to DC voltage.
Av = (Output voltage fluctuation) / (Input offset fluctuation)
2.6 Output saturation voltage (VOM)
Signifies the voltage range that can be output under specific output conditions.
2.7 Input common-mode voltage range (Vicm)
Indicates the input voltage range where IC operates normally.
2.8 Common-mode rejection ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when the input common mode voltage is changed. It is
normally the fluctuation of DC.
CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)
2.9 Power supply rejection ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of
DC. PSRR= (Change of power supply voltage)/(Input offset fluctuation)
2.10 Slew rate (SR)
Indicates the ratio of the change in output voltage with time when a step input signal is applied.
2.11 Unity Gain Frequency (fT)
Indicates a frequency where the voltage gain of Op-Amp is 1.
2.12 Gain Bandwidth (GBW)
The product of the open-loop voltage gain and the frequency at which the voltage gain decreases 6dB/octave.
2.13 Phase Margin (θ)
Indicates the margin of phase from 180 degree phase lag at unity gain frequency.
2.14 Equivalent input noise voltage (Vn)
Indicates a noise voltage generated inside the operational amplifier reflected back to an ideal voltage source
connected in series with input terminal.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
4/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
2.15 Total Harmonic Distortion+ Noise (THD+N)
Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage
of driven channel.
2.16 Channel Separation (CS)
Indicates the fluctuation in the output voltage of the driven channel with reference to the change of output voltage of
the channel which is not driven.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
5/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Typical Performance Curves
○LM4565F
8
7
SUPPLY CURRENT [mA]
POWER DISSIPATION [mW]
800
600
LM4565F
400
200
-40°C
6
5
4
25°C
3
85°C
2
1
0
0
0
85
25
50
75
AMBIENT TEMPERATURE [℃]
±0
100
±6
±9
±12 ±15
SUPPLY VOLTAGE [V]
±18
Figure 3.
Supply Current – Supply Voltage
8
20
7
15
Maximum Output Voltage [V]
SUPPLY CURRENT [mA]
Figure 2.
Derating curve
±3
6
5
4
3
2
1
10
5
0
-5
-10
-15
-20
0
-50
-25
0
25
50
75
AMBIENT TEMPERATURE [°C]
0
100
5
10
15
SUPPLY VOLTAGE [V]
20
Figure 5.
Maximum Output Voltage – Supply Voltage
(RL=2kΩ, Ta=25°C)
Figure 4.
Supply Current – Ambient Temperature
(VCC/VEE = ±15V)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
6/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
20
20
15
15
Maximum Output Voltage [V]
Maximum Output Voltage [V]
●Typical Performance Curves (Reference data) – Continued
○LM4565F
10
5
0
-5
-10
10
5
0
-5
-10
-15
-15
-20
-20
-50
-25
0
25
50
75
±0
100
AMBIENT TEMPERATURE [°C]
±20
Figure 7.
Maximum Output Voltage – Supply Voltage
(Io=25mA, Ta=25°C)
Figure 6.
Maximum Output Voltage – Ambient Temperature
(VCC/VEE = ±15V, RL=2KΩ)
20
3
INPUT OFFSET VOLTAGE [mV]
15
Maximum Output Voltage [V]
±5
±10
±15
SUPPLY VOLTAGE [V]
10
5
0
-5
-10
-15
2
1
0
-1
-2
-3
-20
-50
-50
-25
0
25
50
75 100
AMBIENT TEMPERATURE [°C]
-25
0
25
50
75
100
AMBIENT TEMPERATURE [°C]
Figure 9.
Input Offset Voltage – Ambient Temperature
(VCC/VEE = ±15V)
Figure 8.
Maximum Output Voltage – Ambient Temperature
(VCC/VEE = ±15V, Io=25mA)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
7/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
3
150
2
125
1
INPUT BIAS CURRENT [nA]
INPUT OFFSET VOLTAGE [mV]
●Typical Performance Curves (Reference data) – Continued
○LM4565F
-40°C
0
85°C
25°C
-1
-2
100
75
50
25
0
-3
-15
-10
-5
0
5
10
-50
15
INPUT COMMON MODE VOLTAGE [V]
COMMON MODE REJECTION RATIO [dB] .
LARGE SIGNAL VOLTAGE GAIN [dB] .
140
130
120
110
100
90
80
-25
0
25
50
75
0
25
50
75
100
Figure 11.
Input Bias Current – Ambient Temperature
(VCC/VEE = ±15V)
Figure 10.
Input Offset Voltage – Input Common mode Voltage
(VCC/VEE = ±15V)
-50
-25
AMBIENT TEMPERATURE [°C]
130
120
110
100
90
80
70
-50
100
AMBIENT TEMPERATURE [°C]
Figure 12.
Large Signal Voltage Gain – Ambient Temperature
(VCC/VEE = ±15V, RL=2kΩ)
-25
0
25
50
75 100
AMBIENT TEMPERATURE [°C]
Figure 13.
Common Mode Rejection Ratio – Ambient Temperature
(VCC/VEE = ±15V)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
8/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
10
140
SLEW RATE L-H [V/µs]
POWER SUPPLY REJECTION RATIO [dB]
●Typical Performance Curves (Reference data) - Continued
○LM4565F
120
100
80
8
6
4
2
60
0
-50
-25
0
25
50
75
AMBIENT TEMPERATURE [°C]
100
-50
Figure 14.
Power Supply Rejection Ratio – Ambient Temperature
10
-25
0
25
50
75 100
AMBIENT TEMPERATURE [°C]
Figure 15.
Slew Rate L-H – Ambient Temperature
(VCC/VEE = ±15V, RL=2kΩ, CL=100pF)
100
200
80
6
4
2
150
60
100
Gain
40
50
20
0
-50
0
-25
0
25
50
75
100
AMBIENT TEMPERATURE [°C]
0
2
10
Figure 16.
Slew Rate H-L – Ambient Temperature
(VCC/VEE = ±15V, RL=2kΩ, CL=100pF)
PHASE [deg]
8
GAIN[dB]
SLEW RATE H-L [V/µs]
Phase
103
104
105
106
FREQUENCY [Hz]
107
Figure 17.
Voltage Gain・Phase – Frequency
(VCC/VEE = ±15V, RL=2kΩ)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
9/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Typical Performance Curves (Reference data) - Continued
○LM4565F
Equivalent Input Noise Voltage [nV/√Hz]
TOTAL HARMONIC DISTORTION [%]
1
0.1
0.01
0.001
20Hz
1kHz
20kHz
0.0001
25
20
15
10
5
0
0.01
0.1
1
10
100
OUTPUT VOLTAGE [Vrms]
Figure 18.
Total Harmonic Distortion – Output Voltage
(VCC/VEE = ±15V, RL = 2kΩ, f = 1kHz)
Equivalent Input Noise Voltage [µVrms]
30
0
10
101
102
103
104
FREQUENCY [Hz]
105
Figure 19.
Equivalent Input Noise Voltage – Frequency
(VCC/VEE=±15V, Ta = 25°C, Av = 40dB)
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
±0
±5
±10
±15
±20
SUPPLY VOLTAGE [V]
Figure 20.
Equivalent Input Noise Voltage – Supply Voltage
(Ta = 25°C, DIN-AUDIO)
(*)The data above is measurement value of typical sample, it is not guaranteed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
10/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Application Information
NULL method condition for Test Circuit 1
VCC, VEE, EK, Vicm Unit:V
Parameter
Input Offset Voltage
VF
S1
S2
S3
VCC
VEE
EK
VF1
ON
ON
OFF
15
-15
0
ON
ON
ON
15
-15
VF2
Large Signal Voltage Gain
Vicm Calculation
2
-10
ON
ON
OFF
15
-15
0
VF5
VF6
0
10
VF4
Power Supply Rejection Ratio
1
-10
VF3
Common-mode Rejection Ratio
(Input Common-mode Voltage Range)
0
3
10
ON
ON
OFF
VF7
4
-4
18
-18
0
0
4
－ Calculation－
|VF1|
1. Input Offset Voltage (Vio)
Vio =
[V]
2. Large Signal Voltage Gain (Av)
Av = 20Log ΔEK × (1+RF/RS)
|VF2-VF3|
3. Common-mode Rejection Ratio (CMRR)
CMRR = 20Log ΔVicm × (1+RF/RS) [dB]
|VF4 - VF5|
1+RF/RS
4. Power Supply Rejection Ratio (PSRR)
PSRR
= 20Log
[dB]
ΔVcc × (1+ RF/RS)
[dB]
|VF6 - VF7|
0.1µF
RF=50kΩ
0.01µF
500kΩ
SW1
VCC
EK
RS=50Ω
15V
Vo
Ri=10kΩ
500kΩ
0.1µF
0.1µF
DUT
NULL
SW3
RS=50Ω
1000pF
Ri=10kΩ
Vicm
50kΩ
VF
RL
VRL
-15V
VEE
Figure21. Test circuit 1
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
11/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
Switch Condition for Test Circuit 2
SW No.
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12
Supply Current
OFF OFF
ON
OFF
ON
OFF OFF OFF OFF OFF OFF OFF
Maximum Output Voltage RL=2kΩ
OFF
OFF OFF
ON
OFF OFF
Slew Rate
OFF OFF
Maximum Frequency
ON
ON
ON
OFF OFF
ON
OFF OFF
OFF
OFF OFF OFF
OFF OFF OFF
ON
ON
ON
ON
OFF
ON
OFF OFF
ON
ON
OFF OFF
ON
Input voltage
SW３
SW4
R2
100kΩ
●
VH
●
VCC=30V
－
SW1
VL
SW2
SW5
t
＋
SW6
SW7
SW8
SW9
SW10
SW11
Input wave
SW12
Output voltage
R1
1kΩ
90% SR=ΔV/Δt
VH
RL
VIN-
VIN+
CL
Vo
ΔV
10%
VL
Δt
Figure 22. Test circuit2
t
Output wave
Figure 23 Slew rate input output wave
R2=100kΩ
R2=100kΩ
VCC
VCC
R1=1kΩ
R1=1kΩ
V
～
R1//R2
VIN
VEE
OUT1
=1Vrms
V OUT2
～
R1//R2
VEE
CS=20Log
100×OUT1
OUT2
Figure 24. Test circuit 3 (Channel Separation)
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
12/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
Application example
○Voltage follower
Voltage gain is 0dB.
Using this circuit, the output voltage (OUT) is controlled
to be equal to the input voltage (IN). This circuit also
stabilizes OUT due to high input impedance and low
output impedance. Computation for OUT is shown
below.
OUT=IN
VCC
OUT
IN
VEE
Figure 25. Voltage follower
○Inverting amplifier
R2
For inverting amplifier, IN is amplified by a voltage gain
decided by the ratio of R1 and R2.The out-of-phase
output voltage is shown in the next expression.
OUT=-(R2/R1)・IN
This circuit has input impedance equal to R1.
VCC
R1
IN
OUT
R1//R2
VEE
Figure 26. Inverting amplifier circuit
○Non-inverting amplifier
R1
For non-inverting amplifier, IN is amplified by a voltage
gain decided by the ratio of R1 and R2. OUT is in-phase
with Vin and is shown in the next expression.
OUT=(1+R2/R1)・IN
Effectively, this circuit has high input impedance since its
input side is the same as that of the operational
amplifier.
R2
VCC
OUT
IN
VEE
Figure 27. Non-inverting amplifier circuit
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
13/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Power Dissipation
Power dissipation (total loss) indicates the power that the IC can consume at Ta=25°C (normal temperature). As the IC
consumes power, it heats up, causing its temperature to be higher than the ambient temperature. The allowable
temperature that the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and
consumable power.
Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the
thermal resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the
maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold
resin or lead frame of the package. Thermal resistance, represented by the symbol θja°C/W, indicates this heat dissipation
capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance.
Figure 28(a) shows the model of the thermal resistance of the package. The equation below shows how to compute for the
Thermal resistance (θja), given the ambient temperature (Ta), maximum junction temperature (Tjmax), and power
dissipation (Pd).
θja = (Tjmax－Ta) / Pd °C/W
・・・・・ (Ⅰ)
The Derating curve in Figure 28(b) indicates the power that the IC can consume with reference to ambient temperature.
Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal
resistance (θja), which depends on the chip size, power consumption, package, ambient temperature, package condition,
wind velocity, etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a
reference value measured at a specified condition. Figure 29(c) shows an example of the derating curve for LM4565.
LSIの 消 費
力 [W]
Power dissipation
of 電
LSI
θja=(Tjmax-Ta)/Pd
Pd (max)
°C/W
θja2 < θja1
P2
Ambient temperature Ta[ °C]
θ' ja2
P1
θ ja2
Tj ' (max) Tj (max)
θ' ja1
Chip surface temperature Tj[ °C]
0
25
50
θ ja1
75
100
125
150
Ambient temperature
周 囲 温 度 Ta [℃ ]
(a) Thermal resistance
(b) Derating curve
Figure 28. Thermal resistance and derating
POWER DISSIPATION [mW]
800
LM4565F
600
400
200
0
0
25
50
75
100
AMBIENT TEMPERATURE [°C]
(c) LM4565
5.52
mW/°C
When using the unit above Ta=25°C, subtract the value above per °C. Permissible dissipation is the value
when FR4 glass epoxy board 70mm×70mm×1.6mm (cooper foil area below 3%) is mounted
Figure 29. Derating curve
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
14/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Operational Notes
1) Processing of unused circuit
It is recommended to apply the connection (see the Figure 30.) and set the
non-inverting input terminal at a potential within the input common-mode voltage
range (Vicm) for any unused circuit.
2) Applied voltage to the input terminal
For normal circuit operation of voltage comparator, please input a voltage for its
input terminal within input common mode voltage. Then, regardless of
power supply voltage, (VEE) – 0.3V can be applied to input terminals without
deterioration or destruction of its characteristics.
VCC
VCC
+
Connect
to Vicm
Vicm
VEE
VEE
Figure 30. The example of
application circuit for unused op-amp
3) Operating power supply (split power supply/single power supply)
The voltage comparator operates if a certain level of voltage is applied between
VCC and VEE. Therefore, the operational amplifier can be operated under
single power supply or split power supply.
4) Power dissipation (Pd)
If the IC is used under excessive power dissipation, an increase in the chip temperature will cause deterioration of the
electrical characteristics of the IC. As an example, reduction of current capability may happen. Take consideration of the
effective power dissipation and thermal design with a sufficient margin. Pd is reference to the provided power dissipation
curve.
5) Short circuits between pins and incorrect mounting
When mounting the IC on a printed circuit board, take notice of the direction and position of the IC. If IC is mounted
erroneously, it may be damaged. Also, when a foreign object is inserted between outputs, between output and VCC
terminal, or between output and VEE terminal, it causes short circuit which may damage the IC.
6) Usage under strong electromagnetic field
Be careful when using the IC under strong electromagnetic field because it may malfunction.
7) Usage of IC
When pressure is applied to the IC through warp on the printed circuit board, the characteristics may fluctuate due to
piezo effect. Be careful with the warp on the printed circuit board.
8) Testing IC on the application board
When testing IC on the application board, in cases where the capacitor is connected to low impedance, make sure to
discharge per process because there is a possibility that the IC may be damaged due to stress. When removing IC from
the application board, it is essential to cut supply voltage. As a countermeasure against the static electricity, observe
proper grounding during fabrication process and take due care when carrying and storing it.
9) The IC destruction caused by capacitive load
The IC may be damaged when VCC terminal and VEE terminal is shorted with the charged output terminal capacitor.
When IC is used as an operational amplifier or as an application circuit where oscillation is not activated by an output
capacitor, output capacitor must be kept below 0.1μF in order to prevent the damage mentioned above.
10) Decoupling capacitor
Insert the decoupling capacitor between VCC and VEE for stable operation of operational amplifier.
Status of this document
The Japanese version of this document is the formal specification. A customer may use this translation version only for
reference to help reading the formal version.
If there are any differences in the translated version of this document, the formal version takes priority.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
15/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Physical Dimensions Tape and Reel Information
SOP8
<Tape and Reel information>
6
5
+6°
4° −4°
0.3MIN
7
4.4±0.2
6.2±0.3
8
1 2
3
0.9±0.15
5.0±0.2
(MAX 5.35 include BURR)
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
4
0.595
1.5±0.1
+0.1
0.17 -0.05
S
S
0.11
0.1
1.27
1pin
0.42±0.1
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
●Marking Diagram
SOP8(TOP VIEW)
Part Number Marking
LOT Number
1PIN MARK
Product Name
LM4565
Package Type
Marking
SOP8
4565
F
●Land pattern data
PKG
Land pitch
e
Land space
MIE
SOP8
1.27
4.60
all dimensions in mm
Land length
Land width
≥ℓ2
b2
1.10
0.76
b2
e
MIE
ℓ2
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
16/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
LM4565F
●Revision History
Date
Revision
Changes
30.NOV.2012
001
New Release
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
17/17
TSZ02201-0RAR1G200590-1-2
30.NOV.2012 Rev.001
Datasheet
Notice
●General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
●Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2)
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3)
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4)
The Products are not subject to radiation-proof design.
5)
Please verify and confirm characteristics of the final or mounted products in using the Products.
6)
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7)
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8)
Confirm that operation temperature is within the specified range described in the product specification.
9)
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Datasheet
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2)
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2)
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
●Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2)
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3)
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4)
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
●Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
●Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
●Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
●Precaution Regarding Intellectual Property Rights
1) All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2)
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Datasheet
●Other Precaution
1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2)
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3)
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4)
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5)
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.