AD AD8312

100 MHz−2.7 GHz, 45 dB
RF Log Detector
AD8312
Preliminary Technical Data
Its high sensitivity allows measurement at low power levels, thus
reducing the amount of power that needs to be coupled to the
detector. It is essentially a voltage-responding device, with a
typical signal range of 1.25 mV to 224 mV rms or −45 dBm to 0
dBm re 50 Ω.
FEATURES
Complete RF Detector Function
Typical Range : −45 dBm to 0 dBm re 50 Ω
Frequency Response from 100 MHz to 2.7 GHz
Temperature-Stable Linear-in-dB Response
Accurate to 2.7 GHz
Rapid Response: 70 ns to a 10 dB Step
Low Power: 12 mW at 2.7 V
For convenience, the signal is internally ac-coupled, using a 5
pF capacitor to a load of 3 kΩ in shunt with 2 pF. This highpass coupling, with a corner at approximately 16 MHz,
determines the lowest operating frequency. Thus, the source
may be dc-grounded.
APPLICATIONS
Cellular Handsets (GSM, CDMA, WCDMA)
RSSI and TSSI for Wireless Terminal Devices
Transmitter Power Measurement
The AD8312 output, called VOUT, increases from close to
ground to about 1.2 V as the input signal level increases from
1.25 mV to 224 mV. This output is intended for use in
measurement mode. Consult the Applications section of this
data sheet for information on use in this mode. A capacitor may
be connected between the VOUT and CFLT pins when it is
desirable to increase the time interval over which averaging of
the input waveform occurs.
PRODUCT DESCRIPTION
The AD8312 is a complete low cost subsystem for the
measurement of RF signals in the frequency range of 100 MHz
to 2.7 GHz, with a typical dynamic range of 45 dB, intended for
use in a wide variety of cellular handsets and other wireless
devices. It provides a wider dynamic range and better accuracy
than possible using discrete diode detectors. In particular, its
temperature stability is excellent over the full operating range of
−40°C to +85°C.
The AD8312 is available in a 6-lead wafer-level chip scale
package, 1.0 mm x 1.5 mm, and consumes 4.5 mA from a 2.7 V
to 5.5 V supply.
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
PrA
10/29/2004
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
AD8312
Preliminary Technical Data
TABLE OF CONTENTS
Specifications..................................................................................... 3
Applications..................................................................................... 11
Absolute Maximum Ratings............................................................ 5
Basic Connections...................................................................... 11
ESD Caution.................................................................................. 5
Evaluation Board ........................................................................ 11
Pin Configuration and Function Descriptions............................. 6
Outline Dimensions ....................................................................... 13
Typical Performance Characteristics ............................................. 7
Ordering Guide .......................................................................... 13
General Description ....................................................................... 10
Rev. PrA| Page 2 of 13
Preliminary Technical Data
AD8312
SPECIFICATIONS
Table 1. VS = 3 V, CFLT = open, TA = 25°C, 52.3 Ω termination resistor at RFIN, unless otherwise noted.
Parameter
SIGNAL INPUT INTERFACE
Specified Frequency Range
Input Voltage Range
Equivalent Power Range
DC Resistance to COMM
MEASUREMENT MODE
Conditions
RFIN (Pin 6)
Min
Internally AC-Coupled
52.3 Ω External Termination
Maximum Input Level
Minimum Input Level
Slope
Intercept
Output Voltage - High Power In
Output Voltage - Low Power In
Temperature Sensitivity
TA = +25°C
−40°C < TA < +85°C
± 1 dB Error
± 1 dB Error
PIN = –10 dBm
PIN = –40 dBm
PIN = –10 dBm
25°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +25°C
f = 0.9 GHz
Input Impedance
± 1 dB Dynamic Range
Maximum Input Level
Minimum Input Level
Slope
Intercept
Output Voltage - High Power In
Output Voltage - Low Power In
Temperature Sensitivity
TA = +25°C
−40°C < TA < +85°C
± 1 dB Error
± 1 dB Error
PIN = –10 dBm
PIN = –40 dBm
PIN = –10 dBm
25°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +25°C
f = 1.9 GHz
Input Impedance
± 1 dB Dynamic Range
Maximum Input Level
Minimum Input Level
Slope
Intercept
Output Voltage - High Power In
Output Voltage - Low Power In
Temperature Sensitivity
0.1
1.25
–45
Max
2.7
224
0
Unit
100
GHz
mV rms
dBm
kΩ
3020 || 1.35
48
40
2
-46
21.0
-50.4
0.85
0.22
Ω || pF
dB
dB
dBm
dBm
mV/dB
dBm
V
V
- 0.0002
- 0.0050
dB/°C
dB/°C
903 || 1.16
50
40
2
-48
20.3
-51.4
0.839
0.226
Ω || pF
dB
dB
dBm
dBm
mV/dB
dBm
V
V
- 0.0036
-0.0010
dB/°C
dB/°C
440 || 1.14
46
38
-3
-49
19.4
-51.8
0.815
0.229
Ω || pF
dB
dB
dBm
dBm
mV/dB
dBm
V
V
-0.0044
-0.0027
dB/°C
dB/°C
VOUT (Pin 2) shorted to VSET (Pin 3), Sinusoidal
Input Signal
f = 0.1 GHz
Input Impedance
± 1 dB Dynamic Range
Typ
TA = +25°C
−40°C < TA < +85°C
± 1 dB Error
± 1 dB Error
PIN = –10 dBm
PIN = –40 dBm
PIN = –10 dBm
25°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +25°C
Rev. PrA| Page 3 of 13
AD8312
Parameter
f = 2.5 GHz
Input Impedance
± 1 dB Dynamic Range
Maximum Input Level
Minimum Input Level
Slope
Intercept
Output Voltage - High Power In
Output Voltage - Low Power In
Temperature Sensitivity
OUTPUT INTERFACE
Minimum Output Voltage
Maximum Output Voltage1
General Limit
Available Output Current
Residual RF (at 2f)
Output Noise
Fall Time
Rise Time
VSET INTERFACE
Input Resistance
Bias Current Source
POWER INTERFACE
Supply Voltage
Quiescent Current
vs. Temperature
1
Preliminary Technical Data
Conditions
Min
TA = +25°C
−40°C < TA < +85°C
± 1 dB Error
± 1 dB Error
PIN = –10 dBm
PIN = –40 dBm
PIN = –10 dBm
25°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +25°C
VOUT (Pin 2)
No Signal at RFIN, RL ≥ 10 kΩ
RL ≥ 10 kΩ
2.7 V ≤ VS ≤ 5.5 V
Sourcing/Sinking
f = 0.1 GHz (Worst Condition)
RF Input = 2.2 GHz, –10 dBm, fNOISE = 100 kHz,
CFLT open
Input Level = off to 0 dBm, 90% to 10%
Input Level = 0 dBm to off, 10% to 90%
VSET (Pin 3)
RFIN = −10 dBm; VSET = 1.2V
Typ
Max
Unit
365 || 1.1
44
36
-4
-48
18.85
-51
0.774
0.205
Ω || pF
dB
dB
dBm
dBm
mV/dB
dBm
V
V
+0.0053
-0.0047
dB/°C
dB/°C
0.02
2.2
VS – 1
2/1
100
tbd
V
V
V
mA
µV
uV/√Hz
120
85
ns
ns
10
tbd
kΩ
µA
VPOS (Pin 1)
2.7
–40°C ≤ TA ≤ +85°C
Increased output possible when using an attenuator between VOUT and VSET to raise the slope.
Rev. PrA| Page 4 of 13
3.0
4.2
4.3
5.5
V
mA
mA
Preliminary Technical Data
AD8312
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltage VPOS
VOUT, VSET
Input Voltage
Equivalent Power
Internal Power Dissipation
θJA (WLCSP)
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature Range (Soldering 60 sec)
Value
5.5 V
0 V, VPOS
1.6 V rms
+17 dBm
TBD mW
TBD°C/W
125°C
–40°C to +85°C
–65°C to +150°C
260°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrA| Page 5 of 13
AD8312
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin
1
2
3
4
Mnemonic
VPOS
VOUT
VSET
CFLT
5
6
COMM
RFIN
Function
Positive supply voltage (VS), 2.7 V to 5.5 V.
Logarithmic output. Output voltage increases with increasing input amplitude.
Setpoint input. Connect VSET to VOUT for measurement-mode operation.
Connection for an external capacitor to slow the response of the output. Capacitor is connected between CFLT and
VOUT.
Device Common (Ground)
RF Input
Rev. PrA| Page 6 of 13
Preliminary Technical Data
AD8312
1.4
2.8
1.3
2.4
1.2
2
1.1
1.6
1
1.2
0.9
0.8
0.8
0.4
0.7
0
0.6
-0.4
0.5
-0.8
0.4
-1.2
0.3
-1.6
0.2
-2
0.1
-2.4
-2.8
0
-65
-55
-45
-35
-25
-15
-5
5
PIN-dBm
Figure 6. VOUT and Log Conformance vs. Input Amplitude at 1.9 GHz;
−40°C, +25°C, and +85°C
1.4
2.8
1.3
2.4
1.2
2
1.1
1.6
1
1.2
0.9
0.8
0.8
0.4
0.7
0
0.6
-0.4
0.5
-0.8
0.4
-1.2
0.3
-1.6
0.2
-2
0.1
-2.4
-2.8
0
-65
Error - dB
Vout - Volts
Figure 3. VOUT and Log Conformance vs. Input Amplitude at 50 MHz;
−40°C, +25°C, and +85°C
-55
-45
-35
-25
-15
-5
5
PIN-dBm
2.8
1.4
2.8
1.3
2.4
1.3
2.4
1.2
2
1.2
2
1.1
1.6
1.1
1.6
1
1.2
1
1.2
0.9
0.8
0.9
0.8
0.8
0.4
0.8
0.4
0.7
0
0.7
0
0.6
-0.4
0.6
-0.4
0.5
-0.8
0.5
-0.8
0.4
-1.2
0.4
-1.2
-1.6
0.3
0.3
-1.6
0.2
-2
-2
0.2
0.1
-2.4
0
-2.8
Vout - Volts
1.4
-2.4
0.1
-2.8
0
-65
-55
-45
-35
-25
-15
-5
-65
5
-55
-45
-35
-25
-15
-5
5
PIN-dBm
PIN-dBm
Figure 5. VOUT and Log Conformance vs. Input Amplitude at 900 MHz;
−40°C, +25°C, and +85°C
Figure 8. VOUT and Log Conformance vs. Input Amplitude at 2.5 GHz;
−40°C, +25°C, and +85°C
Rev. PrA| Page 7 of 13
Error - dB
Figure 7. VOUT and Log Conformance vs. Input Amplitude at 2.2 GHz;
−40°C, +25°C, and +85°C
Error - dB
Vout - Volts
Figure 4. VOUT and Log Conformance vs. Input Amplitude at 100 MHz;
−40°C, +25°C, and +85°C
Error - dB
Vout - Volts
TYPICAL PERFORMANCE CHARACTERISTICS
AD8312
Preliminary Technical Data
2.8
2.4
2
1.6
1.2
Error - dB
0.8
0.4
0
-0.4
-0.8
-1.2
-1.6
-2
-2.4
-2.8
-64
-60
-56
-52
-48
-44
-40
-36
-32
-28
-24
-20
-16
-12
-8
-4
0
4
8
12
PIN-dBm
Figure 9. Distribution of Error over Temperature after Ambient Normalization
vs. Input Amplitude at 50 MHz
Figure 12. Distribution of Error over Temperature after Ambient Normalization
vs. Input Amplitude at 1.9 GHz
2.8
2.4
2
1.6
1.2
Error - dB
0.8
0.4
0
-0.4
-0.8
-1.2
-1.6
-2
-2.4
-2.8
-64
-60
-56
-52
-48
-44
-40
-36
-32
-28
-24
-20
-16
-12
-8
-4
0
4
8
12
PIN-dBm
Figure 13. Distribution of Error over Temperature after Ambient Normalization
vs. Input Amplitude at 2.2 GHz
2.8
2.8
2.4
2.4
2
2
1.6
1.6
1.2
1.2
0.8
0.8
Error - dB
Error - dB
Figure 10. Distribution of Error over Temperature after Ambient Normalization
vs. Input Amplitude at 100 MHz
0.4
0
-0.4
0.4
0
-0.4
-0.8
-0.8
-1.2
-1.2
-1.6
-1.6
-2
-2
-2.4
-2.4
-2.8
-64
-2.8
-60
-56
-52
-48
-44
-40
-36
-32
-28
-24
-20
-16
-12
-8
-4
0
4
8
12
-64
PIN-dBm
-60
-56
-52
-48
-44
-40
-36
-32
-28
-24
-20
-16
-12
-8
-4
0
4
8
12
PIN-dBm
Figure 11. Distribution of Error over Temperature after Ambient Normalization
vs. Input Amplitude at 900 MHz
Figure 14. Distribution of Error over Temperature after Ambient Normalization
vs. Input Amplitude at 2.5 GHz
Rev. PrA| Page 8 of 13
Preliminary Technical Data
AD8312
Figure 15. VOUT Response Time, RF Off to 0 dBm
Figure 18. Power-On and Power-Off Response
Figure 16. Test Setup for Pulse Response
Figure 19. Test Setup for Power-On and Power-Off Response
Figure 17. Input Impedance vs. Frequency; No Termination Resistor on RFIN
Figure 20. Noise Spectral Density of Output; CFLT = Open
Rev. PrA| Page 9 of 13
AD8312
Preliminary Technical Data
GENERAL DESCRIPTION
The AD8312 is a logarithmic amplifier (log amp) similar in
design to the AD8313; further details about the structure and
function may be found in the AD8313 data sheet and other log
amps produced by Analog Devices. Figure 21 shows the main
features of the AD8312 in block schematic form.
The AD8312 combines two key functions needed for the
measurement of signal level over a moderately wide dynamic
range. First, it provides the amplification needed to respond to
small signals, in a chain of four amplifier/limiter cells, each
having a small-signal gain of 10 dB and a bandwidth of
approximately 3.5 GHz. At the output of each of these amplifier
stages is a full-wave rectifier, essentially a square-law detector
cell, that converts the RF signal voltages to a fluctuating current
having an average value that increases with signal level. A
further passive detector stage is added ahead of the first stage.
Thus, there are five detectors, each separated by 10 dB,
spanning some 50 dB of dynamic range.
The output of these detector cells is in the form of a differential
current, making their summation a simple matter. It can easily
be shown that such summation closely approximates a
logarithmic function. This result is then converted to a voltage,
at pin VOUT, through a high-gain stage. In measurement
modes, this output is connected back to a voltage-to-current
(V–I) stage, in such a manner that VOUT is a logarithmic
measure of the RF input voltage, with a slope and intercept
controlled by the design. For a fixed termination resistance at
the input of the AD8312, a given voltage corresponds to a
certain power level.
The external termination added ahead of the AD8312
determines the effective power scaling. This will often take the
form of a simple resistor (52.3 Ω will provide a net 50 Ω input)
but more elaborate matching networks may be used. This
impedance determines the logarithmic intercept, the input
power for which the output would cross the baseline (VOUT =
zero) if the function were continuous for all values of input.
Since this is never the case for a practical log amp, the intercept
refers to the value obtained by the minimum-error straight-line
fit to the actual graph of VOUT versus PIN. The quoted values
assume a sinusoidal (CW) signal. Where there is complex
modulation, as in CDMA, the calibration of the power response
needs to be adjusted accordingly. Where a true power
(waveform-independent) response is needed, the use of an rmsresponding detector, such as the AD8361, should be considered.
However, the logarithmic slope, the amount by which the
output VOUT changes for each decibel of input change (voltage
or power) is, in principle, independent of waveform or
termination impedance. In practice, it usually falls off
somewhat at higher frequencies, due to the declining gain of the
amplifier stages and other effects in the detector cells. For the
AD8312, the slope at low frequencies is nominally 21.3 mV/dB,
falling almost linearly with frequency to about 19.2 mV/dB at
2.5 GHz. These values are sensibly independent of temperature
and almost totally unaffected by the supply voltage from 2.7 V
to 5.5 V.
Figure 21. Block Schematic
Rev. PrA| Page 10 of 13
Preliminary Technical Data
AD8312
APPLICATIONS
BASIC CONNECTIONS
Figure 22 shows connections for the basic measurement mode.
A supply voltage of 2.7 V to 5.5 V is required. The supply to the
VPOS pin should be decoupled with a low inductance 0.1 µF
surface mount ceramic capacitor. A series resistor of about 10 Ω
may be added; this resistor will slightly reduce the supply
voltage to the AD8312 (maximum current into the VPOS pin is
approximately 9 mA when VOUT is delivering 5 mA). Its use
should be avoided in applications where the power supply
voltage is very low (i.e., 2.7 V). A series inductor will provide
similar power supply filtering with minimal drop in supply
voltage.
Figure 22. Basic Connections for Operation in Measurement Mode
0.9 GHz, and only slightly less at higher frequencies up to
2.5 GHz. At a slope of 21.5 mV/dB, this would amount to an
output span of 967 mV. Figure 23 shows the transfer function
for VOUT at a supply voltage of 3 V, and input frequency of 0.9
GHz.
The load resistance on VOUT should not be lower than 10
kΩ in order that the full-scale output of 1 V can be generated
with the limited available current of 200 µA max. Figure 23
shows the logarithmic conformance under the same conditions.
Figure 23. VOUT and Log Conformance Error vs. Input Level vs. Input Level
The AD8312 has an internal input coupling capacitor. This
eliminates the need for external ac-coupling. A broadband
input match is achieved in this example by connecting a
52.3 Ω resistor between RFIN and ground. This resistance
combines with the internal input impedance of approximately
3 kΩ to give an overall broadband input resistance of 50 Ω.
EVALUATION BOARD
The measurement mode is selected by connecting VSET to
VOUT, which establishes a feedback path and sets the
logarithmic slope to its nominal value. The peak voltage range
of the measurement extends from −45 dBm to 0 dBm at
Table 4 details the various configuration options of the
evaluation board.
Figure 24 shows the schematic of the AD8312 evaluation board.
The layout and silkscreen of the component and circuit sides
are shown in Figure 25 to Figure 28. The board is powered by a
single supply in the range, 2.7 V to 5.5 V. The power supply is
decoupled by a single 0.1 µF capacitor.
Figure 24. Evaluation Board Schematic
Rev. PrA| Page 11 of 13
AD8312
Preliminary Technical Data
Figure 25. Layout of Component Side (WLCSP)
Figure 27. Silkscreen of Component Side (WLCSP)
Figure 26. Layout of Circuit Side (WLCSP))
Figure 28. Silkscreen of Circuit Side (WLCSP)
Table 4. Evaluation Board Configuration Options
Component
VPOS, GND
C2
Function
Supply and Ground Vector Pins
Power Supply Decoupling: The nominal supply decoupling consists of a 0.1 µF capacitor
(C1).
Input Interface: The 52.3 Ω resistor in position R1 combines with the AD8312’s internal
input impedance to give a broadband input impedance of around 50 Ω.
Default Condition
Not Applicable
C2 = 0.1 µF (Size 0603)
R2, R4
Slope Adjust: By installing resistors in R2 and R4, the nominal slope of 20 mV/dB can be
changed. See Slope Adjust discussion for more details.
C3
Filter Capacitor. The response time of VOUT can be modified by placing a capacitor
between CFLT (Pin 4) and VOUT.
Output Interface: R3, R8, and C4 can be used to check the response of VOUT to capacitive
and resistive loading. R3/R8 can be used to attenuate VOUT.
VSET Interface: R7 can be used to reduce capacitive loading from transmission lines.
Alternate Interface: R5 and R6 allow for VOUT and VSET to be accessible from the edge
connector
R2 = Open (Size 0402)
R4 = 0 Ω (Size 0402)
C3 = Open (Size 0603)
R1
R3, R8, C4
R7
R5, R6
Rev. PrA| Page 12 of 13
R1 = 52.3 Ω (Size 0603)
R3 = 1kΩ (Size 0603)
R8 = C4 = open (Size 0402)
R7 = 1kΩ (Size 0603)
R5 = R6 = Open (Size 0402)
Preliminary Technical Data
AD8312
PR05260-0-11/04(PrA)
OUTLINE DIMENSIONS
Figure 29. Wafer-level Chip Scale Package
Dimensions shown in mm
ORDERING GUIDE
AD8312 Products
AD8312ACPZ-REEL71
AD8312ACPZ-WP
AD8312-EVAL
Temperature
Package
–40°C to +85°C
–40°C to +85°C
Package Description
6-Lead Wafer-level Chip Scale Package,
7” Tape and Reel
6-Lead WLCSP, Waffle Pack
Evaluation Board
1
Z = Pb-free part.
Rev. PrA| Page 13 of 13
Package
Outline
CB-6
Branding
Information
Q00
Ordering
Quantity
tbd
CB-6
Q00
tbd