IDT IDTQS3861_13

IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH® PRODUCTS
HIGH-SPEED CMOS 10-BIT
BUS SWITCH WITH
FLOW-THROUGH PINOUT
DESCRIPTION:
FEATURES:
•
•
•
•
•
IDTQS3861
The QS3861 provides a set of ten high-speed CMOS TTL-compatible
bus switches. The low ON resistance (5Ω) of the QS3861 allows inputs to
be connected without adding propagation delay and without generating
additional ground bounce noise. The Bus Enable (BE) signal turns the
switches on.
The QS3861 is characterized for operation at -40°C to +85°C.
Enhanced N channel FET with no inherent diode to Vcc
Ω bidirectional switches connect inputs to outputs
5Ω
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
Available in QSOP and TSSOP packages
APPLICATIONS:
•
•
•
•
•
•
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Power Conservation
Capacitance reduction and isloation
Bus Isolation
Clock Gating
FUNCTIONAL BLOCK DIAGRAM
A0
B0
A9
B9
BE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
c 2013 Integrated Device Technology, Inc.
JANUARY 2013
1
DSC-5767/6
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS(1)
PIN CONFIGURATION
Symbol
Description
VTERM(2)
Max
Unit
VTERM(3)
Supply Voltage to Ground
–0.5 to +7
V
DC Switch Voltage VS
–0.5 to +7
V
NC
1
24
Vcc
A0
2
23
BE
VTERM(3)
DC Input Voltage VIN
–0.5 to +7
V
VAC
AC Input Voltage (pulse width ≤20ns)
–3
V
mA
A1
3
22
B0
4
21
IOUT
DC Output Current
120
A2
B1
PMAX
Maximum Power Dissipation
0.5
W
TSTG
Storage Temperature
–65 to +150
°C
A3
5
20
B2
A4
6
19
B3
A5
7
18
B4
A6
8
17
B5
A7
9
16
B6
A8
10
15
B7
A9
11
14
B8
GND
12
13
B9
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. VCC terminals.
3. All terminals except VCC .
CAPACITANCE (TA = +25°C, f = 1MHz, VIN = 0V, VOUT = 0V)
Pins
QSOP/ TSSOP
TOP VIEW
Typ.
Max. (1)
Unit
Control Inputs
3
5
pF
Quickswitch Channels (Switch OFF)
5
7
pF
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
Description
A0 - A9
Bus A
B0 - B9
Bus B
BE
Bus Switch Enable
FUNCTION TABLE(1)
BE
A0 - A9
Function
H
Z
Disconnect
L
B0 - B9
Connect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedance
2
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5V ± 5%
Symbol
Parameter
Test Conditions
Min.
VIH
Input HIGH Voltage
Guaranteed Logic HIGH for Control Pins
2
VIL
Input LOW Voltage
Guaranteed Logic LOW for Control Pins
IIN
Input Leakage Current (Control Inputs)
0V ≤ VIN ≤ VCC
Typ.(1) Max.
Unit
—
—
V
—
—
0.8
V
—
±0.01
±1
μA
I OZ
Off-State Current (Hi-Z)
0V ≤ VOUT ≤ VCC, Switches OFF
—
±0.01
±1
μA
RON
Switch ON Resistance
VCC = Min., VIN = 0V, ION = 30mA
—
5
7
Ω
VCC = Min., VIN = 2.4V, ION = 15mA
—
10
15
VP
Pass Voltage(2)
VIN = VCC = 5V, IOUT = -5μA
3.7
4
4.2
NOTES:
1. Typical values are at VCC = 5V and TA = 25°C.
2. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs VIN AT VCC = 5V
16
14
R ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
V IN
(Volts)
3
2.5
3.0
3.5
V
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
Parameter
Test Conditions(1)
Typ.(2)
Max.
Unit
ICCQ
Quiescent Power Supply Current
VCC = Max., VIN = GND or VCC, f = 0
0.2
3
μA
ΔICC
Power Supply Current per Input HIGH(3)
VCC = Max., VIN = 3.4V, f = 0
⎯
2.5
mA
ICCD
Dynamic Power Supply Current per MHz(4)
VCC = Max., A and B Pins Open,
⎯
0.25
mA/MHz
BE Input Toggling @ 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Typical values are at VCC = 5V and TA = 25°C.
3. Per TTL-driven input (VIN = 3.4V, control inputs only). A and B pins do not contribute to ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
TA = -40°C to +85°C, VCC = 5V ± 5%
CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted.
Symbol
Min. (1)
Parameter
Typ.
Max.
Unit
⎯
⎯
0.25(3)
ns
tPLH
tPHL
Data Propagation Delay(2)
tPZL
tPZH
Switch Turn-On Delay
BE to A or B
1.5
⎯
6.5
ns
tPLZ
tPHZ
Switch Turn-Off Delay(2)
BE to A or B
1.5
⎯
5.5
ns
A to B, B to A
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Blank
8
Tube or Tray
Tape and Reel
QG
PAG
Quarter Size Outline Package - QSOP Green
Thin Shrink Small Outline Package - TSSOP Green
3861
High Speed CMOS 10-Bit Bus Switch
with Flow-Through Pinout
Datasheet Document History
01/25/13
Pg. 1, 5
Updated the Ordering Information by removing non green package version, the “IDT” notation and
Adding Tape and Reel information.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
5
for Tech Support:
[email protected]