FCI-CONNECTOR RM16M-23T

Index
Page
Circular introduction
Circular introduction
6
Plastic connector with metal coupling system
UTG - Metalok Bantam
11
Full plastic circular connector
UTP - Full plastic Bantam
15
Shielded connectors... how to assemble ...
Shielding, how to assemble...
18
Shielded connectors for EMC requirements
UTGS - Shielded Bantam
21
Metal circular connector
UT0 - Bantam
24
Circular accessories
Circular accessories
30
Circular connector with quick mating feature
MBG - Bantamate II
38
Rectangular introduction
Rectangular introduction
42
High performance cable connectors
MS-M
43
Rectangular boardmount connectors
V.35 DTE/DCE
52
Rectangular I/O connectors
MSG
58
Economical connectors
SMS - Qikmate
62
Contacts introduction
Contacts introduction
77
Machined TRIM TRIO contacts
RM/RC
81
Stamped and formed TRIM TRIO contacts
SM-M/SC-M
84
Coax TRIM TRIO contacts
RMDX/RCDX
86
Fibre optic TRIM TRIO contacts
8012 - Fibre optic
92
Dicrimination keys
93
Tooling introduction
Tooling introduction
95
Crimp and extraction tooling for TRIM TRIO
Crimptooling
96
• Specials
Special connectors
UTG
• Circular connectors
UTG
• Rectangular connectors
UTG
• Contacts
Discrimination keys for TRIM TRIO connectors
• Tooling
3
100
UTG
• Accessories
Introduction
TRIM TRIO - The principle
The TRIM TRIO interconnection system is a
fully integrated system, in which 4 contact
types can be used in a variety of connector
styles and sizes, ranging from 1 to 104
contact positions.
This interchangeability offers boundless
design possibilities with a large
commonality throughout the entire range.
The commonality in the system is
established in:
- contact performance and wire range.
- configuration of contact cavities in the
housings.
- crimp tooling
- assembly procedures.
- quality assurance procedures.
- field service and maintenance.
- personnel training.
Products
The contacts, both male and female,
accommodate a wire range of AWG14 up to
AWG30. The 4 contact families are:
- Machined contacts for high performance
(up to 13 Amp current rating), with gold or
tin plating.
- Stamped and formed two-piece contacts,
for more cost effective applications (up to
13 Amp current rating).
- Subminiature coaxial contacts, in a multipiece and a mono-crimp version, for
coaxial or twisted-pair cables.
- Fibre optic contacts to accommodate
1000µ plastic fibres with a cable diameter
of 2.2 mm.
The housings offer many options in contact
cavities and backshell possibilities
The main version are:
- circular connectors:
• full metal
• plastic with metal coupling system
• full plastic
• metallised plastic for shielding
• plastic with quick mating feature
- rectangular, high performance, rack and
panel and printed circuit board versions.
- rectangular, low cost, rack and panel and
printed circuit board versions.
- rectangular connectors for V.35
applications.
- rectangular connectors for I/O
applications.
(See TRIM TRIO selection matrix on the
next page)
The beauty of the TRIM TRIO system means
that the 4 contact types can be combined (both
male and female) in any TRIM TRIO
connector type of any geometry.
The keywords in the TRIM TRIO
interconnection system are standardisation,
versatility, reliability and economy.
These words explain why the TRIM TRIO
name is so well known, and its connectors
are used all over the world.
Standardisation
• The same contact cavity for each type of
housing
• identical crimp tooling for all types of
contacts except fibre optics
4
• reduced manufacturing methods
• standardised operator training
• international acceptance
Versatility
• wide range in current capability
• various contact platings
• wire and cable accommodations
• housings accommodate pin and socket
(male and female) contacts
• variety of terminations
• variations in mounting
• number of sizes
• discrimination keying
• broad range of installation tooling
• variety of possible applications
Reliability
• proven materials
• guaranteed quality assurance per
ISO 9001 certification
• rigid inspection procedures
• positive polarisation
• pin protection
• rugged mouldings
• restricted entry contacts
Economy
•
•
•
•
•
•
•
•
•
low assembly cost
minimal tooling downtime
easy connecting and disconnecting
low wiring cost
simplified personnel education
low inspection cost
removable contacts
reduced number of components
low installed cost
Introduction
Versatility
TRIM TRIO selection matrix
5
Circular
Description
The TRIM TRIO circular connectors are an
integrated group of economical, reliable,
versatile standardised connectors for a
broad spectrum of interconnection
applications.
Being derived from MIL-C-26482 ,input and
output connections can be made with a
large number of sizes ranging from:
• 3 to 48 contact positions in TRIM TRIO
• 4 to 46 contact positions in
MBG Bantamate II
What are the links and
differences between
TRIM TRIO circular, and
MBG Bantamate II
To avoid misunderstandings on the circular
connector ranges, it has to be clearly
understood that there are inevitable links
and differences between all the circular
product ranges (see fig).
Intermateability
• TRIM TRIO circular connectors are
available in UT0, UTG, UTP and UTGS
and are fully intermateable,
interchangeable and intermountable.
• MBG Bantamate II with the unique quick
mating feature plus high number of
mating cycles is not mateable with other
TRIM TRIO circular connectors.
Contacts
• TRIM TRIO and MBG Bantamate II
circular connectors use the size 16 TRIM
TRIO contacts available in machined,
stamped and formed, coax and fibre optic
versions.
Accessories
• TRIM TRIO use the same accessories
such as backshells and dustcaps.
• MBG Bantamate II has his own backshell
Tooling
• TRIM TRIO and MBG Bantamate II use
all the same crimp barrels per wire size
and the same crimptooling.
6
Circular
CIRCULAR INTRODUCTION
UTG
Selection matrix Circular connectors
7
Circular
TRIM TRIO Insert arrangements and moulded-in contact identification
TRIM TRIO arrangements only available for UT0, UTG, UTGS and UTP
TRIM TRIO additional arrangements only available for UTG, UTGS and UTP
Contact identification positions shown are for mating face of pin contact connectors and wire face of socket contact connectors.
8
Circular
CIRCULAR INTRODUCTION
TRIM TRIO cavity dimensions on wire face
TRIM TRIO back shell threading
TRIM TRIO threading dimensions
Shell size
Shell thread size for backshells
PG - thread on PG cable clamp
10
12
14
16
18
20
22
24
9/16 - 24 UNEF
11/16 - 24 UNEF
13/16 - 20 UNEF
15/16 - 20 UNEF
1-1/16 - 18 UNEF
1-3/16 - 18 UNEF
1-5/16 - 18 UNEF
1-7/16 - 18 UNEF
PG9
PG11
PG13.5
PG16
9
PG21
PG29
Circular
Mating Dimensions TRIM TRIO
Shell
size
10
12
14
16
18
20
22
24
10-3VDE
18-7 VDE
20-20VDE
Dimensions in mm
A max.
B max.
57
72
74
81
85
88
101
117
123
72
94,5
101
63
67
74
79
84
57
73.5
74
C max.
D max.
E max.
57.5
72.5
74.0
81
85
89
103
110
127
72.5
95.5
103
63.5
31.8
33
31.8
67.5
76
82
88
57.5
74
76
10
F max.
24.3
G
±0.2
11.4
14.6
26
31.7
34
26
15.4
11.4
17.9
14.6
H max.
J max.
106
136
139
153
161
168
191
207
240
136
175
191
118
126
140
151
162
106
133
140
UTG
- Metalok Bantam
Plastic connector
with metal coupling
system
Description
UTG
“UTG” Metalok Bantam plastic industrial
circular connectors with metal coupling are
a range of multiway connectors to provide
the complete answer to the need for
leightweight, robust circular connectors.
They are available in 8 shell sizes, 11 insert
arrangements all intermateable,
interchangeable and intermountable with
the Trim-Trio “UT0” and “UTP industrial
connector families.
Features and benefits
Performance characteristics
Construction
• Available in 8 shell sizes and 11 insert
arrangements incl. 3 VDE versions.
• Available in plug and receptacle versions
for both male and female contacts.
• Connectors and accessories are moulded
from highly durable glass-filled
thermoplastic.
• Flammability rating: UL94-V0.
• UL approved-file Nr.: E31151
• Metal bayonet ring:
• - Metal wave spring loaded.
• - Locks with audible positive “click”
• - Assures 500 matings and unmatings
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
Connector body
Glass filled thermoplast UL94-V0
Colour: black
Coupling ring:
Nickel plated brass
Tri-lock pins:
Stainless steel
Coupling spring: Spring steel
-55°C to +125°C
5000 MΩ min.
2000 VAC
500 matings and
unmatings.
Vibration
Per MIL-STD202
resistance:
method 204
Thermal
Per MIL-STD202
shock:
method 207
Degree of protection per DIN 40050:
IP67 in mated condition. “H” version used
with UTG —ST cable clamp
Contact accommodation
• “UTG” connectors accept Trim-Trio
removable snap-lock contacts (see
contact section)
• Contacts to be ordered seperately.
How to order
Connector family :
Body variation:
UTG
UTG
0
6
0 : Wall mounting receptacle
6 : Cable plug
1 : Free hanging receptacle
Shell size:
Insert arrangement:
Type of contacts: P : Pin contacts
S : Socket contacts
Plating
N : Nickelplated bayonet ring
Application
No letter : Standard version
H : Water protected version (only receptacle)
Design variation
No letter : Moulded-in contact marking (standard version)
Others : Specials versions
11
14
14
12
12
P
S
H
N
---
UTG
- Metalok Bantam
Cable plug for pin contacts (UTG6- - - -PN)
Part number
UTG6104PN / UTG6103PNVDE
UTG6128PN
UTG61412PN
UTG61619PN
UTG61823PN / UTG6187PNVDEU
UTG62028PN / UTG62020PN
UTG62235PN
UTG62448PN
Shell
size
ØA
10
12
14
16
18
20
22
24
±0.2
21.6
24.8
28.0
31.2
34.3
37.5
40.7
43.9
B max.
31.8
31.8 / 33.0
31.8 / 35.3
31.8
ØC
±0.15
10.9
13.8
17.0
19.9
22.4
25.6
26.5
31.7
ØD
±0.15
12.2
15.1
18.3
21.5
24.0
27.2
30.4
33.5
E
±0.2
19.1
Cable plug for socket contacts (UTG6- - - -SN)
Part number
UTG6104SN / UTG6103SNVDE
UTG6128SN
UTG61412SN
UTG61619SN
UTG61823SN / UTG6187SNVDEU
UTG62028SN / UTG62020SN
UTG62235SN
UTG62448SN
Shell
size
10
12
14
16
18
20
22
24
ØA
±0.2
21.6
24.8
28.0
31.2
34.3
37.5
40.7
43.9
12
B max.
23.9 / 26.75
23.9
23.9 / 29.0
24.9
26.2
ØC
±0.15
10.9
13.8
17.0
19.9
22.4
25.6
28.5
31.7
ØD
±0.15
12.2
15.1
18.3
21.5
24.0
27.2
30.4
33.5
E
±0.2
19.1
UTG
- Metalok Bantam
UTG
Wall mounting receptacle for pin contacts (UTG0- - - -P)
Part number
UTG0104P / UTG0103PVDE
UTG0128P
UTG01412P
UTG01619P
UTG01823P / UTG0187PVDEU
UTG02028P / UTG02020P
UTG02235P
UTG02448P
Shell
size
10
12
14
16
18
20
22
24
A
max.
B
C
ØD
E
F
ØG
ØH
ØJ
±0.15
±0.2
±0.15
±0.25
•0.25
±0.1
±0.1
±0.1
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
2.3
31.7
31.7/34.0
33.3/34.3
33.3
11.3
2.5
11.3/17.9
14.5
3.5
15.3
3.9
17.3
21.8
25.0
28.1
31.3
34.5
37.7
40.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
3.2
For waterprotected version add “H” behind “P” e.g. UTG01412PH
Wall mounting receptacle for socket contacts (UTG0- - - -S)
Part number
UTG0104S / UTG0103SVDE
UTG0128S
UTG01412S
UTG01619S
UTG01823S / UTG0187SVDEU
UTG02028S / UTG02020S
UTG02235S
UTG02448S
Shell
size
A
max.
10
12
14
16
18
20
22
24
24.3/27.6
B
C
ØD
E
F
ØG
ØH
ØJ
±0.15
±0.2
±0.15
±0.25
•0.25
±0.1
±0.1
±0.1
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
17.3
21.8
25.0
28.1
31.3
34.5
37.7
40.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
2.3
24.3
24.3/30.4
27.0
28.0
30.4
11.3
2.5
11.3/17.9
14.5
3.5
15.3
For waterprotected version add “H” behind “S” e.g. UTG01412SH
13
3.2
3.9
UTG
- Metalok Bantam
Free hanging receptacle for pin contacts (UTG1- - - -P)
Part number
UTG1104P / UTG1103PVDE
UTG1128P
UTG11412P
UTG11619P
UTG11823P / UTG1187PVDEU
UTG12028P / UTG12020P
UTG12235P
UTG12448P
Shell
size
10
12
14
16
18
20
22
24
A
max.
B
±0.15
31.7
C
±0.2
8.65
5.0
31.7/34.0
33.3/34.3
33.3
8.65/15.35
12.05
13.85
ØD
±0.15
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
ØE
±0.15
19.5
23.5
27.0
30.0
33.0
36.5
39.5
42.5
For waterprotected version add “H” behind “P” e.g. UTG11412PH
Free hanging receptacle for socket contacts (UTG1- - - -S)
Part number
UTG1104S / UTG1103SVDE
UTG1128S
UTG11412S
UTG11619S
UTG11823S / UTG1187SVDEU
UTG12028S / UTG12020S
UTG12235S
UTG12448S
Shell
size
A
max.
10
12
14
16
18
20
22
24
24.3/27.6
B
±0.15
24.3
C
±0.2
8.65
5.0
24.3/30.4
8.65/15.35
12.05
25.9
13.85
For waterprotected version add “H” behind “S” e.g. UTG11412SH
14
ØD
±0.15
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
ØE
±0.15
19.5
23.5
27.0
30.0
33.0
36.5
39.5
42.5
UTP
- Full plastic Bantam
Full plastic circular
Trim Trio connector
Description
UTP
“UTP” full plastic industrial circular
connectors are a range of multiway
connectors.
“UTP” provides the complete answer to
the need for economical lightweight,
robust circular connectors and is unique
in offering a plastic bayonet coupling ring
incorporating a metal wave spring, which
locks with an audible positive “click”.
It is available in 8 shell sizes, 10 insert
arrangements all intermateable,
interchangeable and intermountable with
the Trim-Trio “UT0” (full metal) and “UTG”
(plastic with metal coupling ring) industrial
connector families.
Features and benefits
Performance characteristics
Construction
• Available in 8 shell sizes and 10 insert
arrangements incl. 2 VDE versions.
• Available in plug and receptacle versions
for both male and female contacts.
• Connectors and accessories are moulded
from highly durable glass-filled
thermoplastic.
• Flammability rating: UL94-V0.
• Plastic bayonet ring:
- Vibration proof thermoplast
- Metal wave spring loaded.
- Locks with audible positive “click”
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
Connector, Bayonet ring and accessories
Gass filled thermoplast UL94-V0
Colour: black
Coupling spring: Spring steel
-55°C to +125°C
5000 MΩ min.
2000 VAC
250 matings and
unmatings.
Degree of protection per DIN 40050:
IP67 in mated condition. “H” version used
with UTG--ST cable clamp
Contact accommodation
• “UTP” connectors accept Trim-Trio
removable snap-lock contacts (see
contacts section)
• Contacts to be ordered seperately.
How to order
Connector family :
Body variation:
UTP
UTP
0 : Wall mounting receptacle
6 : Cable plug
Shell size:
Insert arrangement:
Type of contacts: P : Pin contacts
S : Socket contacts
Application
No letter : Standard version
H : Water protected version (only receptacle)
Design variation No letter : Moulded-in contact marking (standard version)
Others : Specials versions
15
0
6
14
14
12
12
P
S
H
---
UTP
- Full plastic Bantam
Cable plug for pin contacts (UTP6- - - -P)
Part number
UTP6104P / UTP6103PVDE
UTP6128P
UTP61412P
UTP61619P
UTP61823P / UTP6187PVDEU
UTP62028P
UTP62235P
UTP62448P
Shell
size
Ø A ±0.2
10
12
14
16
18
20
22
24
26.7
31.4
34.5
37.8
40.8
43.9
47.0
50.1
B
max.
31.8
31.8 / 33.0
31.8
ØC
±0.15
10.9
13.8
17.0
19.9
22.4
25.6
28.5
31.7
ØD
±0.15
12.2
15.1
18.3
21.5
24.0
27.2
30.4
33.5
ØE
±0.2
19.1
Cable plug for socket contacts (UTP6- - - -S)
Part number
UTP6104S / UTP6103SVDE
UTP6128S
UTP61412S
UTP61619S
UTP61823S / UTP6187SVDEU
UTP62028S
UTP62235S
UTP62448S
Shell
size
Ø A ±0.2
B
max.
10
12
14
16
18
20
22
24
26.7
31.4
34.5
37.8
40.8
43.9
47.0
50.1
23.9 / 26.75
16
23.9
23.9 / 29.0
24.9
26.2
ØC
±0.15
10.9
13.8
17.0
19.9
22.4
25.6
28.5
31.7
ØD
±0.15
12.2
15.1
18.3
21.5
24.0
27.2
30.4
33.5
ØE
±0.2
19.1
UTP
- Full plastic Bantam
UTP
Wall mounting receptacle for pin contacts (UTP0- - - -P)
Part number
UTP0104P / UTP0103PVDE
UTP0128P
UTP01412P
UTP01619P
UTP01823P / UTP0187PVDEU
UTP02028P
UTP02235P
UTP02448P
Shell
size
10
12
14
16
18
20
22
24
A
max.
B
±0.15
C
±0.2
2.3
31.7
11.3
31.7/34.0
2.5
33.3
3.5
11.3/17.9
14.5
15.3
ØD
±0.15
E
±0.25
F
•0.25
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
ØD
±0.15
E
±0.25
F
•0.25
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
ØG
±0.1
ØJ
±0.1
3.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
ØG
±0.1
ØJ
±0.1
3.2
For waterprotected version add “H” behind “P” e.g. UTP01412PH
Wall mounting receptacle for socket contacts (UTP0- - - -S)
Part number
UTP0104S / UTP0103SVDE
UTP0128S
UTP01412S
UTP01619S
UTP01823S / UTP0187SVDEU
UTP02028S
UTP02235S
UTP02448S
Shell
size
A
max.
10
12
14
16
18
20
22
24
24.3/27.6
B
±0.15
C
±0.2
2.3
24.3
24.3/30.4
27.0
28.0
30.4
11.3
2.5
11.3/17.9
14.5
3.5
15.3
3.2
3.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
For waterprotected version add “H” behind “S” e.g. UTP01412SH
17
17
Shielded connectors
Shielded circular
TRIM TRIO
connectors
UT0 and UTGS
Description
With the increasing coverage of the
electromagnetic spectra and the constantly
increasing use of electronic hardware, the
need for control on electronic equipment to
operate in electromagnetically noisier
environments and greater control is one of
the main issues.
More and more electronic equipment will be
required to meet an EMC (Electro Magnetic
Compatibility) specification which controls
the level of EM emmisions being upset by
interfering RF (Radio Frequency) and EM
(Electro Magnetic) fields.
A full solution to the problem consists in the
consideration of each and every aspect
within a design, starting at the board level
and working outwards through the
connector to the enclosure and then on to
the power supply and signal cabling.
As a result, UT0 and UTGS are available
with shielded backshells including a
“ two conical ferrule shielding system”.
Shielding effectiveness is a functional
method to characterise the shield leakage,
since it offers us the relation between the
measured power progression from shielding
leakage and the reference power delivered
to the test-cel.
Formula: Shielding effectiveness in dB
S. E.
(dB) = 10 x Log
P out
Test set-up
The measurements are performed with the
triaxial setup.
The connectors are embedded in a
rectangular testcell (see picture)
For the circular connectors an inner
conductor is contructed to obtain a 50Ω
coaxial transmission line, to which a power
level Pin is delivered. The shield of the
connector and the walls from the triaxial
cell form the second coaxial transmission
line. The output power
Pout at one end of the short-circuited
second transmission line is measured with
a spectrum analyser. From the average of
these quantities, the shielding effectiveness
is calculated (see formula and resulting
chart).
( )
Pin
Shielding effectiveness chart for UT0 and UTGS
18
Shielded connectors
SHIELDED CONNECTORS
How to assemble shielded connectors ...
Put all parts over the cable, including the coupling ring, as mentioned on the picture.
Strip the outer jacket with the dimensions given in the table.
Recommended cable strip dimensions
Bend the braid backwards over the cable jacket.
Strip the wires (refer to contact section).
Crimp the contacts.
Insert contact into connector.
Slide inner shielding ferrule over the connector.
Bend the braid back over the conical part of the inner shielding
ferrule.
Cut the shield so that it does not pass the front edge as shown
Wrap shielding around inner shielding ferrule using a conductive
tape.
.Make sure that the braid is wrapped equally around the ferrule to
avoid misalignment when assembled.
19
Shielded connectors
How to assemble shielded connectors ... (cont.)
Slide coupling ring forwards over the connector.
Slide outer shielding ferrule over the shield.
Push the cable a little foreward to avoid stress on wires, contact
and braid after tightening the PG-tube.
Screw the PG-tube onto the connector using a strap wrench.
Put the plug in an empty receptacle and fix the receptacle in a bench.
Tighten the PG-tube with the recommended torque moments given in
table and prevent the cable of twisting.
For Strap wrench and torque meters cosult factory.
Screw the sealing and the PG-nut into the PG-tube to achieve sealing.
Tighten up cable clamp.
Note: Tightening the PG-tube with its PG-nut and sealing might twist the
braid.
Recommended torque moments to tighten PG-tube onto connector.
Shielded connector in assembled condition.
20
UTGS
- Shielded Bantam
Metallised plastic
connector for
EMC requirements
Description
UTGS
“UTGS” Shielded Bantam are a range of
industrial circular connectors suitable for
EMC requirements.
It is a range of multiway connectors
available in 8 shell sizes and 11 insert
arrangements all intermateable,
interchangeable and intermountable with
the Trim-Trio “UT0” metal connector
families.
Finding its origin in the “UTG” range,
“UTGS” keeps the metal locking system,
whilst the connectors are selectively
metallised.
This together with a new shielded backshell
offers a competent, reliable, user friendly
and cost effective solution .
Features and benefits
Performance characteristics
Construction
• Suitable for EMC requirements.
• Shielded backshell is independent from
the cable diameter and its shielding.
• Available in 8 shell sizes and 13 insert
arrangements incl. 3 VDE versions and
one power version.
• Available in plug and receptacle versions
for both male and female contacts.
• Connectors are moulded from highly
durable glass-filled thermoplastic.
Selectively nickel plated
• Flammability rating: UL94-V0.
• Metal bayonet ring:
- Metal wave spring loaded.
- Locks with audible positive “click”
- Assures 500 matings and unmatings
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
unmatings.
Vibration
resistance:
Thermal
shock:
Corrosion:
Connector body
Glass filled thermoplast UL94-V0
Colour: black
Selectively nickel plated
Coupling ring: Nickel plated brass
Tri-lock pins: Stainless steel
Coupling spring: Spring steel
Shielded backshell : Nickel plated
Aluminium alloy.
-55°C to +125°C
5000 MΩ min.
2000 VAC
500 matings and
Per MIL-STD202
method 204
Per MIL-STD202
method 207
Salt spray per MIL-STD 202
method 101
Shielding effectiveness: 95 dB at 1 Mhz
(See shielded connectors section)
Degree of protection per DIN 40050:
IP67 in mated condition. “H” version
Contact accommodation
• “UTGS” connectors accept Trim-Trio
removable snap-lock contacts (see
contact section)
• Contacts to be ordered seperately.
How to order
Connector family:
Body variation:
UTGS
UTGS
6
0
PG
0 : Wall mounting receptacle
6 : Cable plug
1 : Free hanging receptacle
Shielded backshell:
Shell size:
Insert arrangement:
Type of contacts:
P : Pin contacts
S : Socket contacts
Application:
No letter : Standard version
H : Water protected version (only receptacle)
Design variation:
No letter : Moulded-in contact marking ( standard version)
others : Special versions
Plating:
N : Nickel plated
21
14
14
12
12
P
S
H
–
–
N
N
UTGS
- Shielded Bantam
Shielded cable plug for pin contacts (UTGS6PG- - - -PN)
Part number
UTGS6PG104PN / UTGS6PG103PNVDE
UTGS6PG128PN
UTGS6PG1412PN
UTGS6PG1619PN
UTGS6PG1823PN / UTGS6PG187PNVDEU
UTGS6PG2028PN / UTGS6PG2020PN
UTGS6PG2235PN
UTGS6PG2448PN
Shell
size
A
B
10
12
14
16
18
20
22
24
70/74.1
74
81
84
88/94.4
101
107
120
C
±0.2
52.2/56.3
53.2
58.2
61.2
65.2/71.6
70.9
76.9
81.9
D
Max.
31.8
19.1
31.8/33.0
31.8/35.3
31.8
ØE
F
±0.15
±0.15
Max
cable Ø
12.2
15.1
18.3
21.5
24.0
27.2
30.4
33.5
21.6
24.8
28.0
31.2
34.3
37.5
40.7
43.9
11.0
13.5
14.5
16.5
16.5
22.0
22.0
29.5
Max
cable Ø
- For ass’y procedure see shielded connectors section
Shielded cable plug for socket contacts (UTGS6PG- - - -SN)
Part number
UTGS6PG104SN / UTGS6PG103SNVDE
UTGS6PG128SN
UTGS6PG1412SN
UTGS6PG1619SN
UTGS6PG1823SN / UTGS6PG187SNVDEU
UTGS6PG2028SN / UTGS6PG2020SN
UTGS6PG2235SN
UTGS6PG2448SN
Shell
size
A
B
10
12
14
16
18
20
22
24
70/74.1
74
81
84
88/94.4
101
107
120
C
±0.2
- For ass’y procedure see shielded connectors section
22
52.2/56.3
53.2
58.2
61.2
65.2/71.6
70.9
76.9
81.9
D
Max.
ØE
F
±0.15
±0.15
23.9/26.8
12.2
15.1
18.3
21.5
24.0
27.2
30.4
33.5
21.6
24.8
28.0
31.2
34.3
37.5
40.7
43.9
23.9
19.1
23.9/29.0
24.9
26.2
11.0
13.5
14.5
16.5
16.5
22.0
22.0
29.5
UTGS
- Shielded Bantam
UTGS
Shielded wall mounting receptacle for pin contacts (UTGS0- - - -PN)
Part number
UTGS0104PN / UTGS0103PNVDE
UTGS0128PN
UTGS01412PN
UTGS01619PN
UTGS01823PN / UTGS0187PNVDEU
UTGS02028PN / UTGS02020PN
UTGS02235PN
UTGS02448PN
Shell
size
10
12
14
16
18
20
22
24
A
max.
B
C
ØD
E
F
ØG
ØH
ØJ
±0.15
±0.2
±0.15
±0.25
±0.25
±0.1
±0.1
±0.1
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
3.9
17.3
21.8
25.0
28.1
31.3
34.5
37.7
40.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
2.3
31.7
31.7/34.0
33.3/34.3
33.3
11.3
2.5
11.3/17.9
14.5
3.5
15.3
3.2
For waterprotected version add “H” behind “P” e.g. UTGS01412PHN
Shielded wall mounting receptacle for socket contacts (UTGS0- - - -SN)
Part number
UTGS0104SN / UTGS0103SNVDE
UTGS0128SN
UTGS01412SN
UTGS01619SN
UTGS01823SN / UTGS0187SNVDEU
UTGS02028SN / UTGS02020SN
UTGS02235SN
UTGS02448SN
Shell
size
A
max.
10
12
14
16
18
20
22
24
24.3/27.6
B
C
ØD
E
F
ØG
ØH
ØJ
±0.15
±0.2
±0.15
±0.25
±0.25
±0.1
±0.1
±0.1
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
17.3
21.8
25.0
28.1
31.3
34.5
37.7
40.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
2.3
24.3
24.3/30.4
27.0
28.0
30.4
11.3
2.5
11.3/17.9
14.5
3.5
15.3
For waterprotected version add “H” behind “S” e.g. UTGS01412SHN
23
3.2
3.9
UTO
- Bantam
Metal circular
connector
(Suitable for EMC requirements)
Description
“UT0” Bantam industrial circular
connectors are a range of multiway
connectors available in 8 shell sizes and 8
insert arrangements all intermateable,
interchangeable and intermountable with
the Trim-Trio “UTG” , “UTGS” and “UTP
industrial connector families.
“UT0” is equipped with identical shells
from military connectors complying to
MIL-C-26482 spec.
Strong and rugged built to resist every
environmental and mechanical requirement
for indoor and outdoor applications.
In combination with the shielded backshell ,
“UT0” offers the perfect solution to EMC
requirements.
Features and benefits
Performance characteristics
Construction
• Suitable for EMC requirements.
• Shielded backshell is independent of the
cable diameter and its shielding.
• Available in 8 shell sizes and 8 insert
arrangements.
• Available in plug and receptacle version
for both male and female contacts.
• Shells and accessories are made from tin
plated corrosion resistant Aluminium.
• Plastic inserts with flammability rating:
UL94-V0.
• Alu. bayonet ring:
- Metal wave spring loaded.
- Locks with audible positive “click”
- Assures 500 matings and unmatings
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
Vibration
resistance:
Thermal
shock:
Corrosion:
Shells and accessories: Alumimium alloy
Coupling ring: Aluminium alloy
Tri-lock pins: Stainless steel
Coupling spring: Spring steel
Insert: Glass-filled thermoplast UL94-V0
Finish: Bright tin (standard)
-55°C to +125°C
5000 MΩ min.
2000 VAC
500 matings and unmatings.
Per MIL-STD202
method 204
Per MIL-STD202
method 207
Salt spray per MIL-STD 202
method 101
Shielding effectiveness: 95 dB at 1 Mhz
(see shielded connectors section)
Degree of protection per DIN 40050:
IP65 in mated condition. “H” version used
with UTG-PG cable clamp
Contact accommodation
• “UT0” connectors accept Trim-Trio
removable snap-lock contacts (see
contacts section)
• Contacts to be ordered seperately.
How to order
UT0
UT0
Body variation:
0
6
0 : Wall mounting receptacle
6 : Cable plug
1 : Free hanging receptacle
7 : Bulk head receptacle for rear panel mounting
Shell size:
Insert arrangement:
Type of contacts: P : Pin contacts
S : Socket contacts
Insert polarisation: No letter : Standard version
Application:
No letter : Standard version
H : Water protected version (only receptacle)
Design variation:
No letter : Standard version
Others : Special versions
Plating:
T : Bright tin (Standard version)
24
14
14
12
12
P
S
–
–
H
––
T
UTO
- Bantam
UTO
Cable plug for pin contacts (UT06- - - -PT)
Part number
Shell
size
UT06104PT
UT06128PT
UT061412PT
UT061619PT
UT061823PT
UT062028PT
UT062235PT
UT062448PT
10
12
14
16
18
20
22
24
ØA
±0.2
21.6
24.8
28.0
31.2
34.3
37.5
40.7
43.9
B max.
31.8
ØC
±0.15
10.2
13.4
16.7
19.7
21.7
24.9
28.1
31.2
ØD
±0.15
12.3
15.1
18.3
21.5
24.0
27.2
30.4
33.5
E
±0.2
19.1
Cable plug for socket contacts (UT06- - - -ST)
Part number
Shell
size
UT06104ST
UT06128ST
UT061412ST
UT061619ST
UT061823ST
UT062028ST
UT062235ST
UT062448ST
10
12
14
16
18
20
22
24
ØA
±0.2
21.6
24.8
28.0
31.2
34.3
37.5
40.7
43.9
25
B max.
31.8
24.9
26.2
ØC
±0.15
10.2
13.4
16.7
19.7
21.7
24.9
28.1
31.2
ØD
±0.15
12.3
15.1
18.3
21.5
24.0
27.2
30.4
33.5
E
±0.2
19.1
UTO
- Bantam
Wall mounting receptacle for pin contacts (UT00- - - -PT)
Part number
UT00104PT
UT00128PT
UT001412PT
UT001619PT
UT001823PT
UT002028PT
UT002235PT
UT002448PT
Shell
size
10
12
14
16
18
20
22
24
A
max.
B
C
ØD
E
F
ØG
ØH
ØJ
±0.25
±0.2
±0.15
±0.25
•0.25
±0.1
±0.1
±0.1
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
26.9
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
3.9
17.3
21.8
25.0
28.1
31.3
34.5
37.7
40.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
1.6
31.7
11.3
14.5
33.3
2.4
15.3
3.2
For waterprotected version add “H” behind “P” e.g. UT001412PHT
Wall mounting receptacle for socket contacts (UT00- - - -ST)
Part number
Shell
size
A
max.
B
C
ØD
E
F
ØG
ØH
ØJ
±0.25
±0.2
±0.15
±0.25
•0.25
±0.1
±0.1
±0.1
15.0
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.3
20.6
23.0
24.6
26.9
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
17.3
21.8
25.0
28.1
31.3
34.5
37.7
40.9
15.1
18.2
21.4
24.6
27.8
30.9
34.1
37.3
UT00104ST
10
UT00128ST
12
1.6
UT001412ST
14
24.3
11.3
UT001619ST
16
UT001823ST
18
UT002028ST
20
14.5
UT002235ST
22
25.9
2.4
UT002448ST
24
15.3
For waterprotected version add “H” behind “S” e.g. UT001412SHT
26
3.2
3.9
UTO
- Bantam
UTO
Free hanging receptacle for pin contacts (UT01- - - -PT) - suitable for cable to cable applications
Part number
Shell
size
UT01104PT
UT01128PT
UT011412PT
UT011619PT
UT011823PT
UT012028PT
UT012235PT
UT012448PT
10
12
14
16
18
20
22
24
A
max.
B
±0.25
31.7
1.6
33.3
2.4
C
±0.2
11.3
14.5
15.3
ØD
±0.15
14.9
19.0
22.2
25.3
28.5
31.7
34.9
38.0
ØE
max.
24.1
26.4
28.8
31.2
33.6
36.8
39.9
43.1
For waterprotected version add “H” behind “P” e.g. UT011412PHT
Free hanging receptacle for socket contacts (UT01- - - -ST) - suitable for cable to cable applications
Part number
Shell
size
UT01104ST
UT01128ST
UT011412ST
UT011619ST
UT011823ST
UT012028ST
UT012235ST
UT012448ST
10
12
14
16
18
20
22
24
A
max.
B
±0.25
24.3
1.6
25.9
2.4
C
±0.2
11.3
14.5
15.3
For waterprotected version add “H” behind “S” e.g. UT011412SHT
27
ØD
±0.15
14.9
19.0
22.2
25.3
28.5
31.7
34.9
38.0
ØE
max.
24.1
26.4
28.8
31.2
33.6
36.8
39.9
43.1
UTO
- Bantam
Bulk head receptacle for pin contacts (UT07- - - -PT) - suitable for rear panel mounting
Part number
UT07104PT
UT07128PT
UT071412PT
UT071619PT
UT071823PT
UT072028PT
UT072235PT
UT072448PT
Shell
size
10
12
14
16
18
20
22
24
A
B
±0.15
±0.2
14.9
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.0
D
max.
F
max.
31.7
3.2
33.3
6.4
22.7
23.6
G
H
K
L
ØM
±0.25
•0.2
±0.2
±0.12
±0.2
27.0
31.8
34.9
38.1
41.3
46.1
49.2
52.4
22.2
27.0
30.2
33.3
36.5
39.7
42.9
46.0
16.6
20.8
23.9
27.1
30.3
33.4
36.6
39.8
17.0
21.2
24.3
27.5
30.6
33.8
37.0
40.1
17.7
22.5
25.7
28.7
32.0
35.2
38.4
41.5
For waterprotected version add “H” behind “P” e.g. UT071412PHT
Bulk head receptacle for socket contacts (UT07- - - -ST) - suitable for rear panel mounting
Part number
UT07104ST
UT07128ST
UT071412ST
UT071619ST
UT071823ST
UT072028ST
UT072235ST
UT072448ST
Shell
size
10
12
14
16
18
20
22
24
A
B
±0.15
±0.2
14.9
19.0
22.2
25.3
28.5
31.7
34.9
38.0
18.0
D
max.
F
max.
24.3
3.2
25.9
6.4
22.7
23.6
For waterprotected version add “H” behind “S” e.g. UT071412SHT
28
G
H
K
L
ØM
±0.25
•0.2
±0.2
±0.12
±0.2
27.0
31.8
34.9
38.1
41.3
46.1
49.2
52.4
22.2
27.0
30.2
33.3
36.5
39.7
42.9
46.0
16.6
20.8
23.9
27.1
30.3
33.4
36.6
39.8
17.0
21.2
24.3
27.5
30.6
33.8
37.0
40.1
17.7
22.5
25.7
28.7
32.0
35.2
38.4
41.5
UTO
- Bantam
UTO
Notes
29
Circular
- accessories
Plastic cable clamp with strain relief (UTG - - AC)
Part number
UTG10AC
UTG12AC
UTG14AC
UTG16AC
UTG18AC
UTG20AC
UTG22AC
UTG24AC
Shell
size
10
12
14
16
18
20
22
24
Cable range
Ø
3.0
3.0
4.0
5.0
5.0
5.0
5.0
8.0
-
ØA
8.70
12.8
13.8
17.0
19.0
21.0
23.0
27.0
± 0.4
21.0
24.0
27.0
30.2
33.3
36.5
39.7
42.9
L
± 0.5
40.0
40.0
46.0
46.0
50.0
55.0
60.0
65.0
Plastic cable clamp with strain relief nut for waterprotected (IP65) applications (UTG - - PG)
Part number
UTG10PG
UTG12PG
UTG14PG
UTG16PG
UTG18PG
UTG20PG
UTG22PG
UTG24PG
Shell
size
Sealing*
outer dia x inner dia’s
10
12
14
16
18
20
22
24
13.5 x 5 x 8
16 x 7 x 10.5 x 13 x 16
18.5 x 7 x 105 x 13 x 16
20.5 x 8 x 10.5 x 13 x 16
20.5 x 8 x 10.5 x 13 x 16
26 x 11 x 15 x 18 x 22
26 x 11 x 15 x 18 x 22
35 x 19 x 23 x 27 x 31
L
±1
54
57
62
68
71
82
88
103
*In order to accommodate different cable dia’s, the sealing exisits of different layers which can be pulled out easily.
30
A
± 0.5
21.0
24.0
27.0
30.2
33.3
36.5
39.7
42.9
Circular
- accessories
CIRCULAR ACCESSORIES
Plastic cable clamp with strain relief nut for waterprotected (IP67) applications (UTG - - ST)
Part number
UTG10ST
UTG12ST
UTG14ST
UTG16ST
UTG18ST
UTG20ST
UTG22ST
UTG24ST
Shell
size
Cable range
10
12
14
16
18
20
22
24
2-6
3-7
6-9
7 - 12
Dia. A
± 0.5
21.0
24.0
27.0
30.2
33.3
36.5
39.7
42.9
9 - 16
13 - 20
L
±1
64
64
69
72
76
80
86
91
Metal cable clamp with strain relief nut for waterprotected applications (UT0 - - PGT)
Part number
Shell
size
Sealing*
outer dia x inner dia’s
L ±1
UT010PGT
10
13.5 x 5 x 8
53
UT012PGT
12
16 x 7 x 10.5 x 13 x 16
57
UT014PGT
14
18.5 x 7 x 105 x 13 x 16
62
UT016PGT
16
20.5 x 8 x 10.5 x 13 x 16
68
UT018PGT
18
20.5 x 8 x 10.5 x 13 x 16
71
UT020PGT
20
26 x 11 x 15 x 18 x 22
82
UT022PGT
22
26 x 11 x 15 x 18 x 22
88
UT024PGT
24
35 x 19 x 23 x 27 x 31
103
*In order to accommodate different cable dia’s, the sealing exisits of different layers which can be pulled out easily.
31
A
±0.25
16.7
20.1
23.0
26.2
29.6
32.5
35.7
39.2
Circular
- accessories
Shielded cable clamp only suitable for UTGS connectors (UTGS----PGN)
Part number
For pin contacts
For socket contacts
Shell
Sealing*
size
ØA
L
outer dia x inner dia’s
UTGS10PGN
10
8.8
54
13.5 x 5 x 8
UTGS12PGN
12
12.0
57
16 x 7 x 10.5 x 13
UTGS14PGN
14
14.4
62
18.5 x 7 x 105 x 13 x 16
UTGS16PGN
16
16.4
68
20.5 x 8 x 10.5 x 13 x 16
UTGS18PGN
18
16.8
71
20.5 x 8 x 10.5 x 13 x 16
UTGS20PGPN
UTGS20PGSN
20
22.3
82
26 x 11 x 15 x 18 x 22
UTGS22PGPN
UTGS22PGSN
22
22.3
88
26 x 11 x 15 x 18 x 22
UTGS24PGPN
UTGS24PGSN
24
30.0
103
35 x 19 x 23 x 27 x 31
*In order to accommodate different cable dia’s, the sealing exisits of different layers which can be pulled out easily.
Shielded cable clamp only suitable for UT0 connectors (UT0S----PG00T)
Part number
For pin contacts
For socket contacts
Shell
Sealing*
size
ØA
L
outer dia x inner dia’s
UT0S10PG00T
10
8.8
54
13.5 x 5 x 8
UT0S12PG00T
12
12.0
57
16 x 7 x 10.5 x 13 x 16
UT0S14PG00T
14
14.4
62
18.5 x 7 x 105 x 13 x 16
UT0S16PG00T
16
16.4
68
20.5 x 8 x 10.5 x 13 x 16
UT0S18PG00T
18
16.8
71
20.5 x 8 x 10.5 x 13 x 16
UT0S20PGP00T
UT0S20PGS00T
20
22.3
82
26 x 11 x 15 x 18 x 22
UT0S22PGP00T
UT0S22PGS00T
22
22.3
88
26 x 11 x 15 x 18 x 22
UT0S24PGP00T
UT0S24PGS00T
24
30.0
103
35 x 19 x 23 x 27 x 31
*In order to accommodate different cable dia’s, the sealing exisits of different layers which can be pulled out easily.
32
Circular
- accessories
CIRCULAR ACCESSORIES
Environmental dustcap for plugs (UTG6--DCG)
Part number
Shell size
UTG610DCG
UTG612DCG
UTG614DCG
UTG616DCG
UTG618DCG
UTG620DCG
UTG622DCG
UTG624DCG
For dustcap without chain skip “G” e.g. UTG612DC
A max.
10
12
14
16
18
20
22
24
B
20.0
24.0
27.5
30.5
33.5
36.5
40.0
43.0
20.8
22.5
Metal environmental dustcap for receptacles (UTG--DCG)
Part number
UTG10DCG
UTG12DCG
UTG14DCG
UTG16DCG
UTG18DCG
UTG20DCG
UTG22DCG
UTG24DCG
For dustcap without chain skip “G” e.g. UTG12DC
Shell size
A max.
10
12
14
16
18
20
22
24
20.8
24.9
28.1
31.3
34.4
37.6
40.8
43.9
33
Circular
- accessories
Plastic environmental dustcap for receptacles (UTP--DCG)
Part number
Shell size
UTP10DCG
UTP12DCG
UTP14DCG
UTP16DCG
UTP18DCG
UTP20DCG
UTP22DCG
UTP24DCG
For dustcap without chain skip “G” e.g. UTP12DC
ØA
10
12
14
16
18
20
22
24
B max.
±0.2
26.7
31.4
34.5
37.8
40.8
43.9
47.0
50.1
19.3
20.0
20.2
21.8
Sealing for square flange receptacle (UTFD1-B)
Part number
UTFD12B
UTFD13B
UTFD14B
UTFD15B
UTFD16B
UTFD17B
UTFD18B
UTFD19B
Shell size
Ø F ±0.1
R ±0.25
S ±0.25
10
12
14
16
18
20
22
24
15.9
19.0
22.2
25.4
28.6
31.8
34.9
38.1
18.3
20.6
23.0
24.6
27.0
29.4
31.8
34.9
23.8
26.2
28.6
31.0
33.3
36.5
39.7
42.9
34
ØV
3.3
4.0
Circular
- accessories
CIRCULAR ACCESSORIES
A – General duty Termination
Part number
B10P36E
B12P36E
B14P36E
B16P36E
B18P36E
B20P36E
B22P36E
B24P36E
Shell size
ØA
ØB
VV - Thread
UNEF
VV1 - Thread
UNEF
10
12
14
16
18
20
22
24
18,2
21,1
24,6
27,6
30,8
33,8
37,0
40,3
11,3
14,2
17,4
20,6
22,9
26,1
29,3
32,4
9/16-24
11/16-24
13/16-20
15/16-20
1 1/16-18
1 3/16-18
1 5/16-18
1 7/16-18
5/8-24
3/8-20
7/8-20
1-20
1 3/8-18
1 3/8-18
1 7/16-18
1 7/16-18
Shell size
ØA
ØB
C
VV - Thread
UNEF
10
12
14
16
18
20
22
24
18,2
21,1
24,6
27,6
30,8
33,8
37,0
40,3
4,8
7,9
9,7
12,7
15,9
15,9
19,1
20,3
22,6
25,8
29,0
30,6
35,6
35,6
40,4
41,9
9/16-24
11/16-24
13/16-20
15/16-20
1 1/16-18
1 3/16-18
1 5/16-18
1 7/16-18
F – Strain Relief Clamp Termination
Part number
B10SRE
B12SRE
B14SRE
B16SRE
B18SRE
B20SRE
B20SRE
B24SRE
35
Circular
- accessories
J – Gland Seal Termination
Part number
B10P442E
B12P442E
B14P164E
B16P164E
B18P164E
B20P164E
B22P164E
B24P164E
Shell size
ØA
Ø max
VV - Thread
UNEF
10
12
14
16
18
20
22
24
18.6
21.8
25.0
28.2
31.3
34.5
37.7
40.9
7.9
11.2
13.7
15.6
17.1
19.0
21.5
22.7
9/16-24
11/16-24
13/16-20
15/16-20
1 1/16-18
1 3/16-18
1 5/16-18
1 7/16-18
JF – Gland Seal Termination with Strain Relief
Part number
B10P443E
B12P443E
B14P184E
B16P184E
B18P184E
B20P184E
B20P184E
B24P184E
Shell size
ØA
ØB
C
VV - Thread
UNEF
10
12
14
16
18
20
22
24
18.6
21.8
25.0
28.2
31.3
34.5
37.7
40.9
7.9
11.2
13.7
15.6
17.1
19.0
21.5
22.7
22.6
25.8
29.0
30.6
37.3
37.3
42.1
44.4
9/16-24
11/16-24
13/16-20
15/16-20
1 1/16-18
1 3/16-18
1 5/16-18
1 7/16-18
36
Circular
- accessories
CIRCULAR ACCESSORIES
Metal right angle cable clamp with strain relief nut (UTO--LPGN)
Part number
Shell size
A max
B max
Cable range
UTO10LPGN
UTO12LPGN
UTO14LPGN
UTO16LPGN
UTO18LPGN
UTO20LPGN
UTO22LPGN
UTO24LPGN
10
12
14
16
18
20
22
24
42.5
43.5
46.5
53.0
57.0
58.0
58.0
67.0
29.5
31.5
35.5
39.5
455.
46.5
48.0
54.0
13.5 x 5 x 8
16 x 7 x 10.5 x 13
18.5 x 7 x 10.5 x 13 x 16
20.5 x 8 x 10.5 x 13 x 16
20.5 x 8 x 10.5 x 13 x 16
26 x 11 x 15 x 18 x 22
26 x 11 x 15 x 18 x 22
35 x 19 x 23 x 27 x 31
Metal shrink boot adaptor (UTG--AD)
Part number
UTG10AD
UTG12AD
UTG14AD
UTG16AD
UTG18AD
UTG20AD
UTG22AD
UTG24AD
Shell size
Ø A±0.2
10
12
14
16
18
20
22
24
21.0
24.0
27.0
30.0
33.3
36.5
39.7
42.9
Standard plating is anodised black. For tin plating add “T” at the end of the part number e.g. UTG12ADT
37
B
19.2
21.5
22.8
21.9
MBG
- Bantamate II 5000
Plastic connector
with quick mating
feature
Description
The BANTAMATE II cylindrical plastic
connector has been designed for use in
applications requiring a high number of
mating cycles and rapid connections and
disconnections.
BANTAMATE II meets minimum durability
requirements of 5000 mating/unmating
cycles by using a unique contact wiping
system consisting of a lubricant saturated
foam pad bonded to a spring loaded
stripper plate within the receptacle or plug.
On mating, the stripper plate is pushed
deep into the connector wiping a thin film
of lubricant onto the male contacts.
A distinctive shape provides mating ease in
blind or difficult to reach applications.
Some typical applications would include
test equipment, medical diagnostic
equipment, or any of the hardware
interconnections found in the modern
electronic office.
Features and benefits
• 5000 mating / unmating cycles
• Lubricated male contacts with spring
actuated foam plate
• Quick and easy installation with latching
mechanism
• Easy mating due to the positive
polarisation, even in blind spots
• Unmated male contacts are protected by
the spring actuated plate
• Available with 4, 12, 19, 30, and 46
contact positions.
• Applicable for front or rear panel
mounting as well as free hanging
applications
• UL recognised File number E31151
• CSA certified LR54977
Performance characteristics
Construction
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
Vibration
resistance:
Thermal
shock:
Humidity:
Connector body and strain relief:
Glass filled thermoplast UL94-V0
Colour: black
Locking latch
Stainless steel,
and hook:
passivated
Compression
Spring:
Music wire, Nickel plated
Lubricating pad: Polyurethane foam
Rivet:
Brass, Tin plated
Strain relief screws:Steel, Cadmium plated
-55°C to +125°C
5000 MΩ min.
2000 VAC
Min. 5000 matings cycles
5-50Hz, 0,5 dA; 8 hours axis
5 cycles -55°C to +105°C
10 days at 85% RH, +85°C
Contact accommodation
• “MBG” connectors accept Trim-Trio
removable snap-lock contacts (see
contact section)
• Contacts to be ordered seperately.
How to order
Connector family
MBG
12
Insert arrangement:
4, 12, 19, 30, 46 positions
Body variation:
P: Plug body
R: Receptacle body
S: Strain relief
Design variation:
1: Standard version with male contacts in receptacle
11: Reversed version with male contacts in plug
38
P
1
MBG
- Bantamate II 5000
MBG
Female plug connector for socket contacts (MBG--P1) - Standard version
Male plug connector for pin contacts (MBG--P11) - Reversed version
Female plug
Part number
ØA
Male plug
B
±0.25
±0.25
MBG4P1
MBG4P11
15.08
21.90
MBG12P11
19.43
27.25
MBG19P11
22.83
30.53
MBG30P11
27.94
35.51
MBG46P1
34.42
41.91
MBG12P1
MBG19P1
MBG30P1
MBG46P1
Panel mounting male receptacle connector for pin contacts (MBG--R1) - Standard version
Panel mounting female receptacle connector for socket contacts (MBG--R11) - Reversed version
Female plug
Part number
Male plug
Ø A ±0.25
B max.
C
MBG4R11
23.90
18.08
31.45
37.36
20.07
29.46
MBG12R11
32.49
26.54
30.76
36.86
24.64
34.93
MBG19R11
32.44
26.54
34.04
40.13
27.86
38.10
MBG30R11
35.61
28.65
38.00
44.91
33.10
43.31
MBG46R11
42.24
35.13
46.94
54.05
39.70
49.61
±0.18
D
±0.30
ØE
±0.18
F max.
MBG4R1
MBG12R1
MBG19R1
MBG30R1
MBG46R1
39
MBG
- Bantamate II 5000
Strain relief (MBG--S1)
Part number
ØC
ØD
MBG4S1
MBG12S1
MBG19S1
MBG30S1
MBG30S2
MBG46S1
12.2
18.8
21.3
26.7
26.7
15.0
21.1
24.4
29.0
29.0
E
20.1
26.4
29.0
34.5
34.5
Not available
F
5.3
7.9
9.4
16.3
15.9
Insert arrangements and moulded-in contact identification
Contact identification positions shown are for mating face of plug and wiring face of receptacle.
40
Cable range Ø G Cable range Ø G
side A
side B
8.51/6.35
11.30/7.65
13.08/8.66
19.02/15.88
12.67/10.01
–
14.99/11.38
17.53/13.12
22.86/19.05
15.85/12.70
MBG
- Bantamate II 5000
MBG
Panel cut-out dimensions for receptacle - Standard version (MBG--R1)
Part number
MBG4R1
MBG12R1
MBG19R1
MBG30R1
MBG46R1
Fig.
J
K
L
M
N
1
2
2
2
2
20.86
25.30
28.50
33.73
40.36
27.41
32.74
35.89
40.97
47.22
18.08
26.54
31.45
30.76
34.04
38.00
46.94
10.16
11.65
13.32
15.49
18.85
28.65
35.13
Panel cut-out dimensions for receptacle - Reversed version (MBG--R11)
Part number
MBG4R11
MBG12R11
MBG19R11
MBG30R11
MBG46R11
Fig.
J
K
L
M
N
1
2
2
2
2
20.86
25.30
28.50
33.73
40.36
27.41
32.74
35.89
40.97
47.22
18.08
26.54
31.45
30.76
34.04
38.00
46.94
10.16
11.65
13.32
15.49
18.85
41
28.65
35.13
Rectangular
Overview rectangular TRIM TRIO connectors
Selection matrix Rectangular connectors
42
MS-M
- Hyfen rectangular
High performance
hyfen rectangular
cable connectors
Description
Features and benefits
• Connectors supplied pre-assembled
except for panel mount versions.
• Available in 14-20-26-34-42-50-75 and
104 positions.
• 34 contact positions suitable for V.35
applications (see V.35 section)
• Full range of accessories available
including hoods, strain relief clamps,
guide pins, jackscrews and pin protection
shrouds.
• MS-M hyfen complies with NFC 93426 HE 621-622 and MIL-C-28748
specifications.
Performance characteristics
Construction
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
Vibration
resistance
Shock:
Connector Material : Glass filled Phenolic
Flammability rating : UL94-V0
Hoods: Aluminium alloy
gold chromate or anodized
Polyamide 6.6 - black - UL94-V2
Cable clamps: Stainless steel
Polarizing hardware: Brass nickel plated
Shrouds: Aluminium alloy
gold chromate or anodized
-55°C to +125°C
5000 MΩ min.
2000 VAC
500 matings and unmatings.
Per MIL-STD 202
method 204
Per MIL-C-STD 202
method 207
Contact accommodation
• “MS-M” Hyfen connectors accept TrimTrio removable snap-lock contacts (see
contact section)
• Contacts to be ordered seperately.
How to order
Connector family
MS
MS
Contact arrangement
Type of housing:
P: plug body for male contacts
S: Receptacle housing for female contacts
N° 16 contact
Design variation
Pin protection shroud
GE = plastic turnable jackscrews
Code for special variations
43
34
34
P
P
M
M
124
120
S
S-
GE
--
16
--
MS-M
MSM rectangular connectors offers an
extremely reliable, rugged, and versatile
connection system .
They are a range of multiway connectors
available in 8 sizes from 14 to 104
positions.
MS-M cable connectors can be offered with
a full range of hardware and accessories.
Guiding pins and sockets, turnable
jackscrews, a variety of cable hoods, pin
protection shrouds and discrimination pins
make this connector range a truly versatile
system.
MS-M
- Hyfen rectangular
Contact arrangement
The contact position identification letters or numbers shown in the above diagrams apply to
MS-M plug and receptacle connectors. Dimensionally, corresponding types of plug and receptacle
mouldings are the same and differ only in that the contact position lettering/numbering of the
plug (MS-PM) is a mirror image of that of the receptacle (MS-RM). Note that pins and/or sockets
can be used in either the plug or receptacle moulding.
Note:
Contact identification is shown for wiring face of the receptacle and mating face at
plug connector.
44
MS-M
- Hyfen rectangular
Connector
size
14
20
26
34
42
50
75
Part number
Plug version for
Receptacle version for
male contacts
female contacts
MS14PM1
MS14RM1
MS20PM1
MS20RM1
MS26PM1
MS26RM1
MS34PM1
MS34RM1
MS42PM1
MS42RM1
MS50PM1
MS50RM1
MS75PM1
MS75RM1
A
B
D
23.8
31.75
33.3
42.8
50.55
57.95
31.8
39.65
41.3
50.8
58.65
69.1
20.1
27.95
27.2
35.7
42.95
50.85
E
Fig.
11.7
15.0
19.1
1-2
22.1
31.2
1-3
E
Fig.
11.7
15.0
19.1
1-2
Panel mount connectors with fixed jackscrew hardware (MS--M58)
Connector
size
14
20
26
34
42
50
75
Part number
Plug version for
Receptacle version for
male contacts
female contacts
MS14PM58
MS14RM58
MS20PM58
MS20RM58
MS26PM58
MS26RM58
MS34PM58
MS34RM58
MS42PM58
MS42RM58
MS50PM58
MS50RM58
MS75PM58
MS75RM58
A
B
D
23.8
31.75
33.3
42.8
50.55
57.95
31.8
39.65
41.3
50.8
58.65
69.1
20.1
27.95
27.2
35.7
42.95
50.85
45
22.1
31.2
1-3
MS-M
Panel mount connectors with guiding hardware (MS--M1)
MS-M
- Hyfen rectangular
Cable connector without strain relief and turnable jackscrew hardware (MS—M57)
Connector
size
14
20
26
34
42
50
75
Part number
Plug version for
Receptacle version for
male contacts
female contacts
MS14PM57
MS14RM57
MS20PM57
MS20RM57
MS26PM57
MS26RM57
MS34PM57
MS34RM57
MS42PM57
MS42RM57
MS50PM57
MS50RM57
MS75PM57
MS75RM57
A
B
D
23.8
31.75
33.3
42.8
50.55
57.95
31.8
39.65
41.3
50.8
58.65
69.1
20.1
27.95
27.2
35.7
42.95
50.85
E
Fig.
11.7
15.0
19.1
1-2
22.1
31.2
1-3
Cable connector with metal butterfly hood and turnable jackscrew hardware (MS--M124K)
Connector
size
14
20
26
34
42
50
75
Part number
Plug version for
Receptacle version for
male contacts
female contacts
MS14PM124K
MS14RM124K
MS20PM124K
MS20RM124K
MS26PM124K
MS26RM124K
MS34PM124K
MS34RM124K
MS42PM124K
MS42RM124K
MS50PM124K
MS50RM124K
MS75PM124K
MS75RM124K
A
B
E
G max
23.8
31.75
33.3
42.8
50.55
57.95
31.8
39.65
41.3
50.8
58.65
69.1
11.7
14.7
15.0
19.1
18
46
Fig.
1-2
22.2
22.1
31.2
31.8
1-3
MS-M
- Hyfen rectangular
Cable connector with metal butterfly hood and fixed jackscrew hardware (MS--M140)
Part number
Plug version for
Receptacle version
male contacts
female contacts
MS14PM140
MS14RM140
MS20PM140
MS20RM140
MS26PM140
MS26RM140
MS34PM140
MS34RM140
MS42PM140
MS42RM140
MS50PM140
MS50RM140
MS75PM140
MS75RM140
A
B
E
G max
23.8
31.75
33.3
42.8
50.55
57.95
31.8
39.65
41.3
50.8
58.65
69.1
11.7
14.7
15.0
19.1
18
22.2
H
Fig.
48.7
1-2
56.7
22.1
31.2
31.8
1-3
Cable connector with metal butterfly hood and guiding hardware (MS--M120)
Connector
size
14
20
26
34
42
50
75
Part number
Plug version for
Receptacle version
male contacts
female contacts
MS14PM120
MS14RM120
MS20PM120
MS20RM120
MS26PM120
MS26RM120
MS34PM120
MS34RM120
MS42PM120
MS42RM120
MS50PM120
MS50RM120
MS75PM120
MS75RM120
A
B
E
G max
23.8
31.75
33.3
42.8
50.55
57.95
31.8
39.65
41.3
50.8
58.65
69.1
11.7
14.7
15.0
19.1
18
22.2
47
H
Fig.
48.7
1-2
56.7
22.1
31.2
31.8
1-3
MS-M
Connector
size
14
20
26
34
42
50
75
MS-M
- Hyfen rectangular
MS34 Cable connector with 1 piece metal suitcase hood (MS34--MEHM)
Plug version for
male contacts
MS34PMEHM
MS34PMSEHM
Part number
Receptacle version for
female contacts
MS34RMEHM
MS34RMSEHM
Description
Anodised hood, plastic strain relief and turnable hardware.
Shielded version with nickel plated hood, metal strain relief and turnable hardware
Cable connector with Alu die cast hood (MS-M157GE00)
Connector
size
50
75
Part number
Plug version for
Receptacle version for
male contacts
female contacts
MS50PM157GE00
MS50RM157GE00
MS75PM157GE00
MS75RM157GE00
A
B
C
D
E max.
F
Fig.
57.95
57.95
65.85
65.85
73.0
73.0
56.0
56.0
20.0
25.0
22.2
31.2
1-2
1-3
48
MS-M
- Hyfen rectangular
Cable connector with die cast hood and turnable jackscrew hardware (MS—MJD10)
Part number
Plug version for
Receptacle version
male contacts
female contacts
MS20PMJD10
MS20RMJD10
MS26PMJD10
MS26RMJD10
MS34PMJD10
MS34RMJD10
MS42PMJD10
MS42RMJD10
MS50PMJD10
MS50RMJD10
MS75PMJD10
MS75RMJD10
A
B
31.75
33.3
42.8
50.55
57.95
39.65
41.3
50.8
58.65
69.1
C
D max
E
G max
Fig.
71
11.7
15
22
44.3
61,5
69
72
80
19.1
22.1
31.2
26.5
27.5
33
1-3
Fig.
1-2
MS-M
Connector
size
20
26
34
42
50
75
Cable connector with diecast hood and fixed jackscrew hardware (MS—MJD58)
Connector
size
20
34
42
50
75
Part number
Plug version for
Receptacle version
male contacts
female contacts
MS20PMJD58
MS20RMJD58
MS34PMJD58
MS34RMJD58
MS42PMJD58
MS42RMJD58
MS50PMJD58
MS50RMJD58
MS75PMJD58
MS75RMJD58
A
B
C
D max
E
G max
31.75
42.8
50.55
57.95
39.65
50.8
58.65
69.1
44,3
61,5
55
11.7
22
63
19.1
22.1
31.2
26.5
27.5
33
49
69
72
1-2
65
1-3
MS-M
- Hyfen rectangular
MSD104 receptacle cable connector with central jackscrew (MSD104RM)
Connector
size
Part number
Orientation of guide sockets
104
MSD104RM489
A, B, C, D
MSD104 plug cable connector without cable clamp (MSD104PM)
Connector
size
Part number
Orientation of guide sockets
104
MSD104PM494
A, B, C, D
50
MS-M
- Hyfen rectangular
MSD104 cable hood with cable clamp (MSH104M1)
Part number
Orientation of guide sockets
104
MSH104M1
A combination hood and cable clamp assembly which can be used on
MSD104 receptacle or cable plug connector
MS-M
Connector
size
MS-M panel cut-out dimensions
Connector
size
Fig.
A
B
C
14
20
26
34
42
50
75
104
1 or 2
1 or 2
2 or 3
4
4
4
4
5
12.45
12.45
15.75
20.83
28.70
28.20
36.60
43.70
51.60
23.80
31.75
33.30
42.80
50.55
57.95
55.60
63.50
72.64
19.80
29.10
29.50
51
D
E
F
---
---
---
49.30
56.90
64.30
6.35
11.90
14.20
12.70
19.40
20.62
V.35 - Interface connectors
V.35 DTE/DCE
Interface connectors
Description
The Telecommunications Standardization
Sector TSS V.35, formerly CCITT V.35 is the
international standard termed “Data
Transmission at 48 Kbps using 60-108 Khz
Group-Band Circuits. It makes use of a 34
contact connection system specially
designed to be used for DTE/DCE that
interface to high speed digital carriers
found in computer, modem and
telecommunication industries.
Being part of the TRIM TRIO wide range of
high reliable rectangular connectors,
MSO34 (boardmount connectors) and
MS34 (cable connectors) are in complete
compliance to this specification.
To meet this specification, insulators have
been manufactured with 34 contact
positions which can be loaded with the
international accepted N∞ 16 TRIM TRIO
.0625” (1.6mm) diameter contacts.
The boardmount connectors (MSO34) are
available in straight and right angle versions
equipped with either solid machined or
stamped and formed male / female
contacts.
The cable connectors (MS34) can be
offered with a full range of hardware and
accessories. Guiding pins and sockets,
turnable jackscrew system, different cable
hoods with strain relief, pin protection
shrouds and discrimination pins make this
connector range as complete as possible.
Features and benefits
• Complete compliance with International
Standards of ISO 2593 for TTS V.35
(formerly CCITT V.35) interfacing.
• In compliance with NFC 93426 - HE621622 and MIL-C-28748 specifications.
• UL recognised.
• UL94-V0 rated thermoplastic
• Boardmount connectors supplied preassembled with dipsolder contacts in
either: - Male or female contacts.
- Machined or stamped and
formed contacts
- Straight or right angle
• Stamped and formed contacts have
selective tin plating on solder tails, thus
eliminating extra flux operations.
• Selective loading possible on request.
• Right angle version equipped with true
position location wafer.
• Hold-down feature available
Intermateability
All the references mentioned are perfectly intermateable, provided that 1 mated pair exists
out of a plug half and a receptacle half.
Mated pairs can be made for following applications:
- Cable to cable
- Cable to panel
- Cable to straight or right-angled boardmount
Technical data on MSO34
PC-Boardmount connectors
Technical data on MS34
Cable connectors
Performance characteristics
Performance characteristics
Operating
temperature:
Current rating:
Contact resistance:
Operating
temperature:
Insulation
resistatance:
Test potential:
Durability:
Vibration
resistance:
Shock:
-55°C to +125°C
7.5 Amp
≤ 3mΩ
Insulation
resistance:
5000 MΩ min.
Test potential: 2000 VAC
Durability:
500 matings and unmatings.
-55°C to +125°C
5000 MΩ min.
2000 VAC
500 matings and unmatings.
Per MIL-STD 202
method 204
Per MIL-STD 202
method 207
Plating table
Plating for solid machined contacts:
No digit (std) = Min. 0.4µ Gold all over,
over Nickel.
T = 3 - 5µ Tin all over
Plating for Stamped and formed contacts :
K9 (std) = Min. 0.4µ Gold in contact
area, 3 - 5µ SnPb on solder
tail.
T = 3 - 5µ Tin all over
Construction
Material : Glass-reinforced thermoplastic
Flammability rating : UL94-V0
Polarising hardware: Brass nickel plated
Contacts: High conductive copper alloy
52
Contact accommodation
• “MS” Cable connectors accept Trim Trio
removable snap-lock contacts (see
contact section)
• Contacts to be ordered separately
Construction
Connector body: Glass-reinforced Phenolic
Flammability rating : UL94-V0
Cable hoods: Aluminium alloy or
Polyamide 6.6
Cable clamps: Stainless steel
Protection Shrouds: Aluminium alloy
Polarising hardware: Brass nickel plated
V.35 - Interface connectors
How to order
Connector family
MSO
34
M
R
G
58
SE1
K9
Contact arrangement
N° 16 contacts
Type of housing
P: Plug body with male contacts
R: Receptacle body with female contacts
Contact termination K: straight dipsolder
G: Right angle dipsolder
H: Reversed version
Type of hardware
1: Guide pin and socket
58: Threaded jackscrew pin and socket
Design variation
E1: Solid machined contacts
SE1: Stamped and formed contacts
SL1: Metal bracket
SEH1: Hold down rivets
V.35
Plating indication
MS034 recommended drilling hole pattern
Size 34
53
V.35 - Interface connectors
MSO34 Straight boardmount connectors
Part number
Version with
Version with
solid machined contacts
stamped and formed contacts
MSO34MPK1E1
Description
MSO34MPK1SE1K9
Guide pin, guide socket and male contacts
MSO34MRK1E1
MSO34MRK1SE1K9
Guide pin, guide socket and female contacts
MSO34MPK58E1
MSO34MPK58SE1K9
Jackscrew pin, jackscrew socket and male contacts
MSO34MRK58E1
MSO34MRK58SE1K9
For other platings: See plating table
Jackscrew pin, jackscrew socket and female contacts
Other solder tail lengths on request
Selective loading on request
MSO34 Right-angled boardmount connectors
Part number
Version with
Version with
solid machined contacts
stamped and formed contacts
Description
MSO34MPG1E(*)1
MSO34MPG1SE(*)1K9
Guide pin, guide socket and male contacts
MSO34MRG1E(*)1
MSO34MRG1SE(*)1K9
Guide pin, guide socket and female contacts
MSO34MPG58E(*)1
MSO34MPG58SE(*)1K9
Jackscrew pin, jackscrew socket and male contacts
MSO34MRG58E(*)1
MSO34MRG58SE(*)1K9
Jackscrew pin, jackscrew socket and female contacts
For other platings: See plating table
Other solder tail lengths on request
(*) Complete part number with “H” for connector with hold down rivets
54
Selective loading on request
V.35 - Interface connectors
MSO34 Right-angled boardmount connectors – Standard version with metal brackets
Part number
Version with
stamped and formed contacts
Description
MSO34MPG1SL1K9
Guide pin, guide socket and male contacts
MSO34MRG1SL1K9
Guide pin, guide socket and female contacts
MSO34MPG58SL1K9
Jackscrew pin, jackscrew socket and male contacts
Jackscrew pin, jackscrew socket and female contacts
Other solder tail lengths on request
Selective loading on request
MSO34 Right-angled boardmount connectors – Reversed version with metal brackets
Part number
Version with
stamped and formed contacts
Description
MSO34MPH1SL1K9
Guide pin, guide socket and male contacts
MSO34MRH1SL1K9
Guide pin, guide socket and female contacts
MSO34MPH58SL1K9
Jackscrew pin, jackscrew socket and male contacts
MSO34MRH58SL1K9
For other platings: See plating table
Jackscrew pin, jackscrew socket and female contacts
Other solder tail lengths on request
55
Selective loading on request
V.35
MSO34MRG58SL1K9
For other platings: See plating table
V.35 - Interface connectors
MS34 Cable connectors with metal butterfly hood
Part number
Version with
male contacts
Version with
female contacts
Description
MS34PM120(*)GE00
MS34RM120(*)GE00
Guide pin, guide socket and butterfly hood.
MS34PM140(*)GE00
MS34RM140(*)GE00
Jackscrew pin , jackscrew socket and butterfly hood.
MS34PM124(*)GE00
MS34RM124(*)GE00
Turnable jackscrew pin, turnable jackscrew socket and butterfly hood.
MS34PM1(*)GE00
MS34RM1(*)GE00
Guide pin and guide socket. No strain relief hood
MS34PM58(*)GE00
MS34RM58(*)GE00
Jackscrew pin and jackscrew socket. No strain relief hood.
MS34PM007(*)GE00
MS34RM007(*)GE00
Turnable jackscrew pin and turnable jackscrew socket. No strain relief hood.
(*) Complete catalogue number with “ S “ for connector with protective shroud.
MS34 Cable connectors with cable clamp
Part number
Version with
male contacts
Version with
female contacts
Description
MS34PM117(*)GE00
MS34RM117(*)GE00
Guide pin, guide socket and cable clamp
MS34PM127(*)GE00
MS34RM127(*)GE00
Jackscrew pin, jackscrew socket and cable clamp
MS34PM107(*)GE10
MS34RM107(*)GE10
Turnable jackscrew pin, turnable jackscrew socket and cable clamp.
(*) Complete catalogue number with “S” for connector with protective shroud.
56
V.35 - Interface connectors
MS34 Cable connectors with metal suitcase hood
Part number
Version with
male contacts
Version with
female contacts
Description
MS34PMEHM(*)
MS34RMEHM(*)
Anodised hood, plastic strain relief and turnable hardware.
MS34PMSEHM(*)
MS34RMSEHM(*)
Shielded version with nickel plated hood, metal strain relief and
turnable hardware.
V.35
(*) Complete catalogue number with “ S “ for connector with protective shroud.
MS34 Cable connectors with plastic suitcase hood
Part number
Version with
male contacts
Version with
female contacts
Description
MS34PMEH2(*)
MS34RMEH2(*)
Guide pin, guide socket and plastic suitcase hood.
MS34PMEH3(*)
MS34RMEH3(*)
Jackscrew pin, jackscrew socket and plastic suitcase hood.
MS34PMEH0(*)
MS34RMEH0(*)
Turnable jackscrew pin, turnable jackscrew socket and plastic suitcase hood.
(*) Complete catalogue number with “S” for connector with protective shroud.
57
MSG - rectangular
High performance
Low profile
rectangular MSG
connectors
Description
MSG Series connectors is a 59 position low
profile, compact design rectangular I/O
connector.
MSG has been developed for industrial
control equipments which require a easy
handling and high density connector.
In addition to its panel mount version, a
PCB mount version has been especially
designed to fit 19 inch Euro-rack system.
Features and benefits
• Connectors supplied pre-assembled.
• Available in 59 positions only.
• PCB mount version fully equipped with
male contacts. Selective contact loading
optional.
• Accessories : polarizing screws
(receptacle)
polarizing plate (plug)
dust cap (plug)
Performance characteristics
Construction
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
Vibration
Salt Spray:
Connector Material : Glass filled
thermoplast
Flammability rating : UL94-V0
Hoods, skirts :
Steel, nickel plated
Cable clamps:
Steel, nickel plated
Guiding hardware:
Stainless steel
Contacts receptacle : Copper alloy
(Au over Ni)
-55°C to +85°C
5000 MΩ min.
2000 VAC
500 matings and unmatings.
Per JIS-C STD 0040
Per JIS-C STD 0023
Contact accommodation
• “MSG” Rectangular connectors accept
Trim-Trio removable RM/RC contacts
(see contact section)
• For the plug connector and the panel
mount receptacle, contacts have to be
ordered separately.
How to order
Part number
Description
MSG59P-L11
Plug for cable up
MSG59P-L21
Plug for cable down
MSG59R-PL110
Panel mount receptacle
MSG59R-RL111
Right angle PCB mount receptacle without flange
MSG59R-FL111
Right angle PCB mount receptacle with flange
MSG-PK1
Polarizing plate
MSG-PK2
Polarizing screw
MSG59R-FC
Dust cap
58
MSG - rectangular
Plug connector with metal hood
MSG
59
P
L
1
1
1
1
0
Series
59 Pos.
Plug
Hood mechanism
L=Lever
Variation
1= Cable up – 2= Cable down
MSG
Polarization
Panel mount Receptacle connector
MSG
59
R
P
L
Series
59 Pos.
Receptacle
Body variation
P=Panel mount
Skirt mechanism
L=Lever
Contact type
1= gold plated RM contact
Polarization
Contact loading
0= Non contact
59
MSG - rectangular
Right angle PCB mount receptacle
without flange
MSG
59
R
R
L
1
1
1
L
1
1
1
Series
59 Pos.
Receptacle
Body variation
R= Right angle without flange
Skirt mechanism
L=Lever
Contact type
1= gold plated RM contact
Polarization
Contact loading
1= Fully loaded
Right angle PCB mount receptacle
with flange
MSG
59
R
F
Series
59 Pos.
Receptacle
Body variation
R= Right angle with flange
Skirt mechanism
L=Lever
Contact type
1= gold plated RM contact
Polarization
Contact loading
1= Fully loaded
60
MSG - rectangular
MSG
MSG recommended panel cut pattern (for panel mount receptacle, front mounting
MSG recommended drilling hole pattern (for PCB right angle receptacle with flange)
61
SMS - Qikmate
Qikmate panel
and cable connectors
Description
The versatile “ SMS “ Qikmate panel and
cable connectors are a highly cost-effective
system approach to solving the constant
demand for more cost effective
interconnection techniques.
It is a range of multiway connectors using
N° 16 TRIM TRIO .0625” (1.6mm) diameter
contacts and available in 10 contact
arrangements from 2 to 36 positions.
Having no additional hardware, Panel
receptacle connectors snap and lock into
panel cutouts and cable plugs quick
connect and disconnect with positive
retention locks.
Cable plug connectors also feature pinprotection skirts, positive polarisation and
can be supplied with or without integrated
strain relief hoods.
Cable receptacle connectors (only with
integrated strain relief hoods) are developed
to mate with cable plug connectors thus
offering solutions for cable to cable
applications.
Features and benefits
• Available in 10 contact arrangements.
• Self mountable panel receptacle with
positive housing retention.
• Cable plugs with retaining latches for
positive locking.
• Cable plug has pin protection skirt to
prevent damage of male contacts
• Positive polarization keys prevent
mismating.
• Cable plug and receptacle have
integrated strain relief hood which can
take a wide range of cables.
• Cable plug and receptacle have
discrimination cavities in between contact
cavities, thus offering discrimination
without contact loss.
Performance characteristics
Construction
Operating
temperature:
Insulation
resistance:
Test potential:
Durability:
-55°C to +105°C
Material : Polyamide 6.6
Flammability rating : UL94-V2
5000 MΩ min.
2000 VAC
500 matings and unmatings.
Contact accommodation
• “SMS” Qikmate connectors accept TrimTrio removable snap-lock contacts (see
contact section)
• Contacts to be ordered seperately.
How to order
Connector family
SMS
SMS
Contact arrangement
Body variation:
R1:
P1:
PDH1:
RDH1:
Panel mount receptacle
Cable plug without strain relief hood
Cable plug with integrated strain relief hood
Cable receptacle with integrated strain relief hood
62
12
12
PDH1
P1
SMS - Qikmate
SMS
Contact arrangements for cable plug connectors (SMS--P1 and SMS--PDH1)
Contact identifications shown are for mating face. Contact identifications of wiring face are identical as shown on the receptacle arrangements
63
SMS - Qikmate
Contact arrangements for cable and panel mount receptacle connectors (SMS--R1 and SMS--RDH1)
Contact identifications shown are for mating face. Contact identifications of wiring face are identical as shown on the plug arrangements
64
SMS - Qikmate
SMS
SMS - Standard Qikmate intermateability chart
( O N LY I N S I Z E S
3, 6, 12 AND 18)
65
SMS - Qikmate
Panel mount receptacle (SMS--R1)
0,75
2,3
Part number
SMS2R1
SMS3R1
SMS4R1
SMS6R1
SMS9R1
SMS12R1
SMS15R1
SMS18R1
SMS24R1
SMS36R1
Number of
contact pos.
A
B
C max.
2
3
4
6
9
12
15
18
24
36
11.0
16.2
21.2
5.8
15.2
16.2
10.9
16.0
21.1
26.2
31.2
20.3
25.4
30.5
35.6
40.6
21.1
30.5
21.2
46.6
J
K
±0.13
11.4
16.5
21.7
16.5
11.6
16.7
21.6
26.7
31.8
36.9
16.7
21.7
47.1
26.7
Cable plug without strain relief hood ( SMS--P1 )
Part number
SMS2P1
SMS3P1
SMS4P1
SMS6P1
SMS9P1
SMS12P1
SMS15P1
SMS18P1
SMS24P1
SMS36P1
Number of
contact pos.
A
C max.
2
3
4
6
9
12
15
18
24
36
15.0
18.6
23.7
17.8
18.6
22.9
27.9
33.0
38.1
43.2
23.7
49.1
66
±0.13
33.0
SMS - Qikmate
Cable receptacle with integrated strain relief hood ( SMS--RDH1 )
SMS2RDH1
SMS3RDH1
SMS4RDH1
SMS6RDH1
SMS9RDH1
SMS12RDH1
SMS15RDH1
SMS18RDH1
SMS24RDH1
SMS36RDH1
Number of Number of
contact pos. disrimination
pos.
2
3
4
6
9
12
15
18
24
36
0
0
0
2
4
6
8
10
15
24
A
31.6
35.1
38.2
34.6
35.8
38.1
35.9
36.1
39.7
54.6
B
9.9
15.0
20.0
25.1
30.2
35.3
25.1
C
D
H
64.8
69.0
74.4
72.6
75.3
72.0
81.3
11.1
16.2
21.2
49..2
90.4
128.0
21.2
46.6
57.2
63.3
C
D
H
64.8
69.0
74.4
72.6
75.3
72.0
81.3
14.1
18.6
23.7
57.1
90.4
128.0
23.7
49.1
16.2
50.9
52.2
52.7
55.2
Cable
range
0.5 - 8.4
0.8 - 7.3
1.5 - 10.0
1.7 - 9.2
3.9 - 14.3
4.0 - 15.0
5.0 - 16.2
5.8 - 20.3
7.1 - 20.4
8.8 - 24.5
Recommended
unirap
cable te
TF4D
TF5D
SMS
Part number
Cable plug with integrated strain relief hood ( SMS--PDH1 )
Part number
SMS2PDH1
SMS3PDH1
SMS4PDH1
SMS6PDH1
SMS9PDH1
SMS12PDH1
SMS15PDH1
SMS18PDH1
SMS24PDH1
SMS36PDH1
Number of Number of
contact pos. disrimination
pos.
2
3
4
6
9
12
15
18
24
36
0
0
0
2
4
6
8
10
15
24
A
39.5
43.0
46.1
42.5
43.7
46.0
43.8
44.0
47.6
62.5
B
16.4
21.5
26.7
31.7
36.7
41.8
31.7
67
18.6
58.8
60.1
60.6
63.1
65.1
71.2
Cable
range
0.5 - 8.4
0.8 - 7.3
1.5 - 10.0
1.7 - 9.2
3.9 - 14.3
4.0 - 15.0
5.0 - 16.2
5.8 - 20.3
7.1 - 20.4
8.8 - 24.5
Recommended
unirap
cable te
TF4D
TF5D
SMS - Qikmate
Accessories for standard Qikmate connectors
Pin protection shroud for panel mount receptacle (SMS--CSB1)
When pins are inserted into the panelmount
receptacle half (SMS--R1) of the QIKMATE
connector, an optional pin protection
shroud can be installed.
The shroud is mounted at the same time as
the receptacle by holding the shroud
against the mating side of the panel with
both cutouts lined up. The receptacle is
then inserted in place, trapping the shroud
between the receptacle and panel. The use
of the pin protection shroud reduces the
allowable thickness of the panel from 2.3 to
1.6 mm max.
Part number
Number of contact
positions
A
B
SMS2CSB1
SMS3CSB1
SMS4CSB1
SMS6CSB1
SMS9CSB1
SMS12CSB1
SMS15CSB1
SMS18CSB1
SMS24CSB1
SMS36CSB1
2
3
4
6
9
12
15
18
24
36
19.8
23.4
28.4
18.8
23.4
23.9
29.0
34.0
39.1
44.2
28.4
54.1
34.0
Strain relief hoods (SMS—H1)
Separate strain relief hoods are available for all standard plugs SMS—P1.
The hoods consist of identical halves that snap into position on the plug and are secured in
place with the cable tie drawn tightly around the cabe entry collar.
Catalog numbers designate a complete hood (2 halves) SMS—H1
The cable tie is not included (TF4D – TF5D)
Two three and four position hoods are single piece units
Discrimination pins
For discrimination pins on both standard Qikmate and Qikmate Pin Headers cable and boardmount:
See accessories section.
68
SMS - Boardmount Qikmate
Qikmate PCboardmount connectors
Description
Features and benefits
• Straight versions available in 10 contact
arrangements from 2 to 36 positions
• Right-angled versions available in 3, 6, 12
and 18 positions.
• All versions are available with:
- Pin or socket contacts
- Stamped and formed or solid machined
contacts.
• Some boardmount connectors have
discrimination cavities in between contact
cavities, thus offering discrimination
without contact loss.
Performance characteristics
Plating table
Operating
temperature: -55°C to +125°C
Insulation
resistance:
5000 MΩ min.
Test potential: 2000 VAC
Current rating: 5 Amp
Durability:
500 matings and unmatings.
Plating for solid machined contacts:
No digit (std) = Min. 0.4µ Gold all over,
over Nickel.
T = 3 - 5µ Tin all over
Plating for Stamped and formed contacts :
K9 (std) = Min. 0.4µ Gold in contact
area, 3 - 5µ Tin on solder
tail.
T = 3 - 5µ Tin all over
Construction
Intermateability
Connector body:
Glass filled thermoplast
UL94-V0
Contacts: High conductive copper alloy
• “SMS” Qikmate boardmount connectors
with preassembled TRIM TRIO boarmount
contacts are intermateable only with the
“SMS” Qikmate cable plug connectors
equipped with TRIM TRIO crimp type
removable snap-lock contacts (see
contact section)
How to order
Connector family
SMS
SMS
Contact arrangement
Contact type:
GE: Solid machined contacts
SE: Stamped and formed contacts
Design variation:
3:
4:
5:
6:
Straight boardmount with female contacts
Straight boardmount with male contacts
Right angle boardmount with female contacts
Right angle boardmount with male contacts
Plating indication
69
12
12
GE
SE
3
3
–
K9
SMS
These PC boardmount connectors enable
QIKMATE and preassembled TRIM TRIO
contacts to be PC board mounted, using
conventional solder production techniques.
They will then mate and latch with the
standard QIKMATE plugs.
Straight boardmount QIKMATE is available
in 10 insert arrangements from 2 to 36
positions.
Right-angled boardmount QIKMATE is
available in 3, 6, 12 and 18 positions.
All boardmount connectors are supplied
fully loaded with pin or socket contacts,
either in solid machined or stamped and
formed contacts.
Stamped and formed contact have
selective tin plating on the solder tails, thus
eliminating flux operations.
SMS - Boardmount Qikmate
Straight boardmount with female contacts (SMS--GE3 / SMS--SE3K9)
Part number
Part number
Solid machined
Stamped and
contacts
formed contacts
SMS2GE3
SMS2SE3K9
SMS3GE3
SMS3SE3K9
SMS4GE3
SMS4SE3K9
SMS6GE3
SMS6SE3K9
SMS9GE3
SMS9SE3K9
SMS12GE3
SMS12SE3K9
SMS15GE3
SMS15SE3K9
SMS18GE3
SMS18SE3K9
SMS24GE3
SMS24SE3K9
SMS36GE3
SMS36SE3K9
For other platings: see plating table
Number of
contact pos.
2
3
4
6
9
12
15
18
24
36
Number of
discrimination
pos.
0
0
0
0
4
0
8
10
0
0
A
B
C
11.0
16.2
21.3
14.0
19.1
10.2
15.2
5.9
10.2
10.9
16.0
21.1
26.1
31.2
16.2
21.2
46.5
19.2
24.2
29.2
34.3
39.4
15.2
D
13.4
15.2
54.6
E
20.9
Straight boardmount with male contacts (SMS--GE4 / SMS--SE4K9)
Part number
Part number
Solid machined
Stamped and
contacts
formed contacts
SMS2GE4
SMS2SE4K9
SMS3GE4
SMS3SE4K9
SMS4GE4
SMS4SE4K9
SMS6GE4
SMS6SE4K9
SMS9GE4
SMS9SE4K9
SMS12GE4
SMS12SE4K9
SMS15GE4
SMS15SE4K9
SMS18GE4
SMS18SE4K9
SMS24GE4
SMS24SE4K9
SMS36GE4
SMS36SE4K9
For other platings: see plating table
Number of
contact pos.
2
3
4
6
9
12
15
18
24
36
Number of
discrimination
pos.
0
0
0
0
4
0
8
10
0
0
70
A
B
C
11.1
16.2
21.3
14.0
19.1
10.2
15.2
5.9
10.2
10.9
16.0
21.1
26.1
31.2
16.2
21.2
46.5
19.2
24.2
29.2
34.3
39.4
15.2
15.2
54.6
D
13.4
E
20.9
SMS - Boardmount Qikmate
Right angle boardmount with female contacts (SMS--GE5 / SMS--SE5K9)
Number of
discrimination
pos.
0
0
6
10
A
B
C
D
E
F
G
16.5
19.0
21.6
20.5
24.5
29.5
30.2
24.2
16.2
14.4
35.2
45.4
29.2
39.4
21.2
31.2
6.8
11.9
17.2
SMS
Part number
Part number
Number of
Solid machined
Stamped and
contact pos.
contacts
formed contacts
SMS3GE5
SMS3SE5K9
3
SMS6GE5
SMS6SE5K9
6
SMS12GE5
SMS12SE5K9
12
SMS18GE5
SMS18SE5K9
18
For other platings: see plating table
For availability on SMS18, consult factory
Right angle boardmount with male contacts (SMS--GE6 / SMS--SE6K9)
Part number
Part number
Number of
Solid machined
Stamped and
contact pos.
contacts
formed contacts
SMS3GE6
SMS3SE6K9
3
SMS6GE6
SMS6SE6K9
6
SMS12GE6
SMS12SE6K9
12
SMS18GE6
SMS18SE6K9
18
For other platings: see plating table
For availability on SMS18, consult factory
Number of
discrimination
pos.
0
0
6
10
71
A
B
C
D
E
F
G
16.5
19.0
21.6
20.5
24.5
29.5
30.2
24.2
16.2
14.4
35.2
45.4
29.2
39.4
21.2
31.2
6.8
11.9
17.2
SMS - Boardmount Qikmate
Recommended PC-Board hole lay out for straight male and female boardmount connectors
Recommended PC-Board hole lay out for right-angled male and female boardmount connectors
72
SMS - Qikmate Pin Header
Qikmate PC
boardmount
Pin Headers and plugs
Qikmate Pin Header, available in 3, 4, 6, 9
and 10 positions, provides the additional
versatility of straight and right angle board
mounting.
Offered as an alternative to stacked
connectors, the in-line contact design of
the pin header provides the user with
significant PC board space savings.
The boardmount receptacle features
positieve polarization and a moulded on pin
protection skirt and is supplied
preassembled with straight or right angled:
• Solid machined or stamped and formed
PC board pin contacts.
• Coax PC board pin contacts.
The socket cable plug features positive
quick connect / disconnect latches and is
designed to accept N° 16 TRIM TRIO
.0625” (1.6mm) diameter socket contacts
for maximum contact protection.
Features and benefits
• Available in 3, 4, 6, 9 and 10 positions.
• In-line contact design, offering significant
PC board space savings.
• Boardmount connectors available in
straight and right-angled version
preassembled with:
- Solid machined or stamped and formed
pin contacts.
• - Coax pin contacts.
Performance characteristics
Plating table
Operating
temperature: -55°C to +125°C
Insulation
resistance:
5000 MΩ min.
Test potential: 2000 VAC
Current rating: 5 AMP
Durability:
500 matings and unmatings.
Plating for solid machined contacts:
No digit (std) = Min. 0.4µ Gold all over,
over Nickel.
T = 3 - 5µ Tin all over
Plating for Stamped and formed contacts :
D28 = Min. 0.75µ Au over nickel.
D70 = Gold flash all over
TR29 = 1.2µ Pre-plated Tin all over.
Plating for coax contacts:
Z17 = Min. 0.75µ Au in contact area,
Flash on solder tail (inner)
Min 0.75µ Au in contact area,
Tin on solder tail (outer)
Intermateability
• “SMS” Socket plugs accept Trim-Trio
removable snap-lock contacts (see
contact section)
• Contacts to be ordered seperately.
Construction
Connector body:
Glass filled thermoplast UL94-V0
Colour: Black
Contacts: High conductive copper alloy
How to order
Connector family
SMS
SMS
SMS
9
9
9
Contact arrangement
Contact type:
PH:
CH:
P3:
Pin header boardmount.
Coax header boardmount.
Socket cable plug for pin and coax boardmount header.
Design variation:
1:
2:
3:
4:
GE6:
GE4:
Right angle coax header boardmount with male contacts.
Straight coax header boardmount with male contacts
Right angle pin header boardmount with stamped male contacts
Straight pin header boardmount with stamped male contacts
Right angle pin header boardmount with machined male contacts
Straight pin header boardmount with machined male contacts
Plating indication
73
PH
CH
P3
3
1
–
TR29
Z17
–
SMS
Description
SMS - Qikmate Pin Header
Right angle pin header boardmount with male contacts (SMS--PH3 / SMS--PHGE6)
Part number
Stamped and
formed contacts
SMS3PH3TR29
SMS4PH3TR29
SMS6PH3TR29
SMS9PH3TR29
SMS10PH3TR29
For other platings: see
Part number
Solid machined
contacts
SMS3PHGE6
SMS4PHGE6
SMS6PHGE6
SMS9PHGE6
SMS10PHGE6
plating table.
Number of
contact
positions
3
4
6
9
10
A
31.2
36.3
46.5
61.7
66.8
B
C
25.4
19.3
30.4
24.4
40.6
34.5
55.9
49.8
61.0
54.9
Other solder tail lenghts on request
Straight pin header boardmount with male contacts (SMS--PH4 / SMS--PHGE4)
Part number
Stamped and
formed contacts
SMS3PH4TR29
SMS4PH4TR29
SMS6PH4TR29
SMS9PH4TR29
SMS10PH4TR29
For other platings: see
Part number
Solid machined
contacts
SMS3PHGE4
SMS4PHGE4
SMS6PHGE4
SMS9PHGE4
SMS10PHGE4
plating table.
Number of
contact
positions
3
4
6
9
10
A
31.2
36.3
46.5
61.7
66.8
74
B
C
25.4
19.3
30.4
24.4
40.6
34.5
55.9
49.8
61.0
54.9
Other solder tail lenghts on request
SMS - Qikmate Pin Header
Right angle coax header boardmount with male contacts (SMS--CH1Z17)
Part number
positions
A
B
C
3
4
6
9
10
31.2
36.3
46.5
61.7
66.8
25.4
30.4
40.6
55.9
61.0
19.3
24.4
34.5
49.8
54.9
SMS
SMS3CH1Z17
SMS4CH1Z17
SMS6CH1Z17
SMS9CH1Z17
SMS10CH1Z17
For plating spec.: see plating table.
Number of contact
Straight coax header boardmount with male contacts (SMS--CH2Z17)
Part number
positions
SMS3CH2Z17
SMS4CH2Z17
SMS6CH2Z17
SMS9CH2Z17
SMS10CH2Z17
For plating spec.: see plating table.
Number of contact
A
B
C
3
4
6
9
10
31.2
36.3
46.5
61.7
66.8
25.4
30.4
40.6
55.9
61.0
19.3
24.4
34.5
49.8
54.9
75
SMS - Qikmate Pin Header
Socket cable plug for pin and coax boardmount header (SMS--P3)
Part number
Number of contact
positions
D
3
4
6
9
10
16.0
21.1
31.2
46.5
51.6
Part number of contact
positions
E
F
3
4
6
9
10
10.18
15.24
25.40
40.64
45.72
25.40
30.48
40.64
55.88
60.96
SMS3P3
SMS4P3
SMS6P3
SMS9P3
SMS10P3
Recommended PC-board hole layouts
76
Contacts - intro
Overview TRIM TRIO contacts
CONTACTS
Selection matrix TRIM TRIO contacts
77
Contacts
Current ratings for multi-contact connectors
Choice of right connector contact combination.
The choice of a Trim Trio connector in
combination with a Trim Trio contact is
essential and different for any application
There is considerable misunderstanding in
the field on current carrying capabilities for
the various contacts in the TrimTrio
programme.
The intention of this part is to give guidance
how to interprete the given current ratings
in general and how to calculate them for
particular applications.
The information given is based upon
existing MIL specifications such as:
MIL-C-26482, MIL-C-8384,
MIL-T-7928, MIL-W-5086,
MIL-W-5088, MIL-W-16878, etc. and in
conjunction with long field practice.
Current carrying capabilities
Trim Trio contacts are designed to carry a
specific current, in accordance with the
applicable specification.
This specification will be defined by
following variables:
• Connector size
The more contacts in a connector, the less
current per contact can be loaded.
• Wire size (see table 1)
The cross section will determine the internal
resistance and temperature rise for a given
current.
-Table 1 gives the current ratings for the
various wire sizes commonly used with Trim
Trio contacts.
• Current rating (see table 2)
The current load for a given application will
generate heat.
- Table 2 gives the maximum current
carrying capacity of most of the Trim Trio
contacts, the maximum operating current
and the recommended continuous current.
• Ambient temperature
The combination of the connector size, the
wire size and the current rating will generate
a temperature rise.
This temperature rise + a given ambient
temperature may not exeed the maximum
operating temperature of the connector
material (see performance characteristics
for each connector family).
Table 1 - Current carrying capabilities per wire size
AWG
wire size
mm2
wire dia.
mm
26
24
22
20
18
16
14
0.13
0.20
0.32
0.52
0.82
1.30
2.10
0.40
0.51
0.64
0.81
1.02
1.29
1.63
max.curr.
carrying
Amp.
3
4.5
9
11
16
22
32
max.operating curr.
Amp.
2
3
5
7.5
10
13
17
recomm.
cont. curr.
max. curr.
carying
Amp.
22
max. operating curr.
Amp.
13
recomm.
cont. curr.
Amp.
10
22
13
10
11
7.5
5
1
2
3
5
7.5
10
13
Table 2 - Current carrying capabilities per contact type
size
pin dia.
16
.062*
1.6 mm
20
.040*
1.0 mm
type
RM / RC
machined
SM / SC
2 piece
stamped
SM-W / SC-W
2 piece
stamped
• Max. current carrying capacity
• Max. operating current
• Recommended continuous current
What do these values mean in practice ?
• Max current carrying capacity
of a contact is defined by the conducting
section of the contact in its smallest area.
The listed values are obtained from several
tests in laboratories under room conditions
(21°C). The contact is considered to be in
free air.
• Max operating current
is the current with which the contacts can
be energized during a longer or shorter
period, without deteriorating and depending
on working conditions.
These are dissipated heat, cooling
provisions, ambient temperature, insulation
material, etc.
78
• Recommended continuous current
can be applied for all normal cases and
working conditions. The values include a
safety margin. However, there are
restrictions in the application of the given
values. The most important restriction is the
used wire, its sectional area, insulation
temperature range, as well as wires in
bundles.
Military specifications require that for a
cable bundle of 15 conductors or more, the
bundle shall not carry more than 20% of
the total carrying capacity of the bundle.
In smaller bundles, the allowable
percentage of total current may be
increased as the bundle approaches the
single wire condition.
This percentage of increase in total current
carrying capacity of the bundle is 6% for
each conductor less than 15 in a bundle.
Contacts
• Example 1
Cable bundle, 48 conductors AWG20
(0.5mm2) used with circular TrimTrio
connector with insert arrangement
24-48 and machined size 16 contacts
RM/RC20.
- Total operating current capacity of
bundle 48 x 7.5 A ( table I) = 360 A
- Total allowable capacity for bundles of
more than 15 wires is 20% = 72 A
- When all conductors are energized
equally, this gives:
72 : 48 = 1.5 A per conductor
When for instance 5 conductors are
energized to the recommended continuous
current of 5 A (see table 1) resulting in 25 A
consumption, the other conductors may not
take more than
72 - 25 = 47 A all together, or 1 A per
conductor.
Any other combination can of course also
be taken as long as the total capacity of 72
A is not exceeded and the recommended
continuous current is respected.
Remark
Please note that contacts used are of the
size 16 type with maximum operating
current of 13 A (table 2).
The maximum operating current of the
bundle is however restricted to 7.5 A per
conductor due to the wire size of AWG20
(see table 1).
• Example 2
Cable bundle, 14 conductors AWG22 (0.32
mm2) used with rectangular
Trim Trio connector with insert arrangement
for 14 contacts, and machined size 16
contacts RM / RC20.
• Example 3
Cable bundle, 4 conductors AWG16
(1.3mm2) used with circular Trim Trio
connector with insert arrangement 10-4 and
stamped 2 piece contacts
SM /SC.
- Total operating current capacity of
bundle 14 x 5 (table I) = 70 A
- Total allowable for wire bundle of 15
wires less 1 is 20% + 6% = 26%
gives 18.2 A.
- All conductors energized equally, gives:
18.2 : 14 = 1.3 A per conductor
- Total operating current capacity of
bundle 4 x 13 A (table I) = 52 A
- Total allowable for wire bundle of 15
wires less 11 is 20% + 66% = 86%
gives 44.7 A.
- All conductors energized equally, gives:
44.7 : 4 = 11.2 A per conductor
This value is within the recommended rating
of 3 A so that it can be applied.
See also remark under example 1.
Since the recommended continuous current
is 10 A, the conductor should not carry
more than 10 A individiually.
As said before, the recommended ratings are valid for most common wiring systems
and under normal working conditions. For extreme conditions, the given values should
be lowered. The percentage of current reduction should be investigated from case to
case.
A rule-of thumb which can be used for such cases is:
4 Amp. per mm2 wire section
It gives us for common used wire sizes the values listed in table 3.
Table 3 - Recommended continuous current for extreme working conditions
AWG
wire size
mm2
recommended
continuous
current
Amp.
26
24
22
20
18
16
14
0.13
0.20
0.32
0.52
0.82
1.30
2.10
0.5
0.8
1.3
2.0
3.3
5.2
8.4
79
CONTACTS
From simple calculations, one can see that
the closer the bundle approaches the single
wire condition, the higher the allowable
current per conductor becomes, to even
such an extent, that it exceeds the
recommended continuous current value. In
that case, the recommended continuous
value should have preference. In order to
make this clear, we will give some typical
examples.
Contacts
Crimping instructions
The conductor and insulation crimp
section
Are designed to accommodate wireconductor and insulation diameters,
expressed in AWG (American Wire Gauge)
or mm2.
For each wire gauge, a correct crimp
requires a crimp height that offers the
highest performance.
This performance is defined as the highest
tensile strength force.
A good conductor crimp can be guaranteed
if the tensile stength force is equal or higher
as indicated on the graph below. E.g. a
conductor of AWG20 (0.52 mm2) has a
good crimp if the tensile strength is min
84N.
The tensile strength force is measured in
Newtons and is the wire-to-contact
connection that will withstand when a
straight axial load is applied to the
terminated wire. This is however a
destructive test and is therefore
inappropriate as a 100% inspection
method.
An alternative method is to measure crimp
height. The crimp height is measured at the
conductor-crimp section.
• If the dimension is too small, then the
conductor is over-crimped and the wire
strands could be damaged, which results
in a lower tensile strength force.
80
• If the dimension is too large, then the
conductor is under-crimped and the wire
strands will not be deformed enough to
assure that the crimp will pass the tensile
strength test.
In both cases, the application tooling’s
crimp height should be adjusted.
In order to have the right tooling’s crimp
height go and no-go gauges can be
obtained and are defined in function of the
type of crimp tooling and the wire gauge.
For further information consult factory.
RM/RC - Machined contacts
Size 16 solid machined
contacts for TRIM
TRIO connectors
Description
Size 16 RM/RC .063” (1.6mm) diameter
contacts are precision solid machined
crimp snap-in pin and sockets for heavy
duty top performance requirements.
Springs on both contacts are made of
spring-tempered, heat-treated, berylium
copper.
The socket inner spring supplies high
contact pressure to ensure low-resistance
contact between pin and socket. The
socket contact features closed entry to
prevent probe damage. Crimp barrels have
insulation grips for vibration support and
are provided with a cable stop and
inspection hole.
Features and benefits
• Made from high conductive copper alloy
with gold or tin over nickel plate finish.
• Heat-treated beryllium copper locking
springs assure proper locking and
alignment of contacts in the housing.
• Closed entry design on RC socket
contact to prevent probe damage.
• Special “RCS” contacts with large lead-in
design
• Contacts available in bulk packing
Performance characteristics
Current rating:
Contact resistance:
13 Amp
3 mΩ
Construction
Connector accommodation
Contact body: High conductive copper
alloy.
Outer spring: Tempered, heat-treated,
beryllium copper.
Inner spring socket: Tempered, heattreated, plated beryllium copper.
Any TRIM TRIO contact can be used in any
contact position in any connector in the
TRIM TRIO interconnection system.
• MS-M / MSG Rectangular connectors
• SMS Qikmate
• G - Bantamate
• UT-Bantam
• UTG Metalok bantam
• UTP Full plastic bantam
• UTGS Shielded bantam
• MBG Bantamate II
Plating table
K (std) = Min. 0.4 µ Gold all over,over
Nickel
T
= 3 - 5 µ Tin all over, over Nickel
D28
= Min. 0.75 µ Gold over Nickel
T3
= 7,5µ - 12,5 µ Tin all over
RM/RC
Contact retention in body: 110 N min.
Individual insertion force:
3.5 N max.
Individual withdrawal force: 0.55 N min.
How to order
(K) RM
(K) RC
Contact type:
RM:
RC:
KRM:
KRC:
AWG Size:
16, 20, 24, 28
Size 16:
.063” (1.6mm) Diameter contacts
Design variation:
Crimp barrel
16
16
Male contact bulk packing
Female contact bulk packing
Male contact on plastic carrier strip
Female contact on plastic carrier strip
Grounding contact:
Plating indication:
See plating table
Packing quantity:
No digit (std)
1000
: 50 pcs. bulk packing (RM/RC)
: 2000 pcs on reel (KRM/KRC)
: 1000 pcs bulk packing (RM/RC)
81
M
M
23
23
(GE1)
(GE1)
K
K
–
–
RM/RC - Machined contacts
Standard RM/RC crimp contacts: Contact size 16 - Pin diameter 1.6mm (.063”)
Dimensional table
Pin contacts
Part number
Fig.
Socket contacts
Standard
RM28M1(*)
RM24M9(*)
RM20M14(*)
RM20M13(*)
RM20M12(*)
RM16M23(*)
RM16M23GE1(*)
RM16M31(*)
RM14M50(*)
RM14M30(*)
1
2
3
4
5
5
Wire size
AWG
mm2
Max.
wire
dia.
Max.
insul.
dia.
6
7
30-28
26-24
0.05-0.08
0.13-0.20
0.55
0.8
8
22-20
0.32-0.52
1.18
20-16
0.52-1.50
1.80
Fig.
Wire
strip
length
O.D.
1.1
1.6
2.6
1.8
2.2
4.8
1.90
2.55
3.10
2.92
2.92
3.2
7.1
L1
L2
26.2
18.2
27.2
28.4
19.7
--
26.2
18.2
RCS-Type
RC28M1(*)
RC24M9(*)
RC20M14(*)
RC20M13(*)
RC20M12(*)
RC16M23(*)
RC16M23GE1(*)
-RC14M50(*)
RC14M30(*)
-RCS24M9(*)
RCS20M14(*)
RCS20M13(*)
RCS20M12(*)
RCS16M23(*)
--RCS14M50(*)
--
9
9
10
10
14
--
2
2,5
2.55
2.05
2.28
3.10
3.10
(*) Plating indication : See plating table
For machined contact reeled on plastic carrier: put “K” in front of part number e.g. KRM16M23K
Crimptooling table
Hand crimp tooling for loose contacts
Size
Hand tools
die set
included
MH860
Positioner
M10S1
Locator
setting
(not incl.)
28-1
24-9
20-12/13
16-23
16-GE1
16-31
20-14
14-50
14-30
MH86164G
Y16RCM
--AF8 +
TP120
Automatic crimp tooling
for contacts on strip
4/6
5/6
5/7
6/8
M8ND
Die set
Stop
bushing
(not incl.)
(not incl.)
S9
Die set
(not incl.)
N24RT10
SL40
S10
N20RT30
N16RT21
N16RT25
P100MAN (Press)
Left side
applicator
KRM/KRC
(not incl.)
(not incl.)
-MLSP2763
MLSP2764
Consult
Factory
MH86186
-MH86164G
--
S3D1
SL39
SL115
-5/7
--
S10J
S3-14
SL40J
SL39
N20RT30J
--
MLSP2765
----
--
--
--
--
--
--
For detailed information on crimp tooling : See crimp tooling section
82
Stripper
unit
Extraction
tools
RX2025GE1
or
RX2025GE2
or
RX16D11D1
RM/RC - Machined contacts
Special RM / RC contacts: Contact size 16 - Pin diameter 1.6mm (.063”)
Part number
Pin contacts
RM16MSC(*)
RM16SEO(*)
RM20M12G4(*)
RM20M12E8(*)
Fig.
Socket contacts
1
1
2
5
RC16MSC(*)
RC16SE4(*)
RC20M12G4(*)
RC20M12E8(*)
RC20M12E83(*)
RC20M12E84(*)
RM20M12G50(*)
4
RC20M12G50(*)
RM20M12G60(*)
3
RC20M12G60(*)
(*) Plating indication : See plating table.
Wire size
Fig.
Type
AWG
mm2
section
A
Length out
of
TRIM TRIO
cavity
6
6
7
Handsolder
Handsolder
Mini - wrap
Dipsolder
Dipsolder
Dipsolder
Dipsolder
Dipsolder
16 - 20
16 - 20
28 - 30
-
1,50 - 0,52
1.50 - 0.52
0.08 - 0.05
-
ø1.7
ø1.7
.636
ø 0.9
ø 0.9
ø 0.9
ø 0.8
ø 0.8
-3.5
16.0
5.2
10.4
13.9
6
6
10
9
8
Antirotating
bushing
part
number
J1661
-
The RCS contact principle
RM/RC
The RC contact principle
Post cross
The RM/RC contact packing
50 pcs bulk packing (standard)
1000 pcs bulk packing
83
Reeled contacts on plastic carrier (qty 2000 pcs)
SM/SC-M Stamped contacts
Size 16 stamped and
formed contacts for
TRIM TRIO connectors
Description
Size 16 SM/SC .063” (1.6mm) diameter
contacts are two piece strip formed crimp
snap-in pin and sockets.
These contacts consist of a crimp body
made of high conductive copper alloy, and
a stainless steel retaining spring featuring
retention in the housing cavity and a closed
entry socket to prevent probe damage.
The contact with its open barrel is standard
available on srtip and packaged with 3000
pcs on reel. This reel packaging combined
with semi or even full automatic crimp
tooling provides the added advantage of a
lower installed cost.
Features and benefits
• Made from high conductive copper alloy
with gold or tin over nickel plate finish.
• Two piece construcion with dual purpose
spring which serves for contact retention
and protects the body against damage.
• Contacts available on reel (standard) and
in bulk packing (100 pcs).
• Suitable for high volumes and lower
installation cost.
Performance characteristics
Current rating:
Contact resistance:
13 Amp
6 mΩ
Construction
Connector accommodation
Contact body: High conductive copper
alloy.
Outer spring: Stainless steel
Any TRIM TRIO contact can be used in any
contact position in any connector in the
TRIM TRIO interconnection system.
• MS-M / MSG Rectangular connectors
• SMS Qikmate
• G - Bantamate
• UT-Bantam
• UTG Metalok bantam
• UTP Full plastic bantam
• UTGS Shielded bantam
• MBG Bantamate II
Plating table
S6 = 0.75m Gold min. in contact area,
flash on crimp barrel over Nickel.
D70 = Gold flash all over, over Nickel.
TK6 = Preplated Tin all over.
Contact retention in body: 65 N min.
Individual insertion force:
3.5 N max.
Individual withdrawal force: 0.55 N min.
How to order
SM
SC
Contact type:
SM: Male contact
SC : Female contact
AWG Size:
14, 16, 20, 24
16
16
Type of crimp barrel: American open crimp barrel
Packing:
No digit: Contacts on strip (qty 3000 per reel)
L: Preformed loose piece contacts
Design variation
1 : Only wire crimp for size 14 and 16
: Wire + insulation crimp for sizes 20 and 24
11 : Wire + insulation crimp for size 16
Plating indication:
See plating table
84
M
M
(L)
(L)
1
1
S6
S6
SM/SC-M Stamped contacts
Standard SM/SC crimp contacts: Contact size 16 - Pin diameter 1.6mm (.063”)
Dimensional table
Part number: contacts on strip
Part number: Loose piecesmn
Pin contacts
Fig.
SM24M1S6
SM24ML1S6
SM20M1S6
SM20ML1S6
SM16M1S6
SM16ML1S6
SM16M11S6
SM16ML11S6
SM14M1S6
SM14ML1S6
1
3
5
7
9
Wire size
Socket contacts
SC24M1S6
SC24ML1S6
SC20M1S6
SC20ML1S6
SC16M1S6
SC16ML1S6
SC16M11S6
SC16ML11S6
SC14M1S6
SC14ML1S6
Fig.
AWG
mm2
Insulation
diameter
Wire
strip length
2
26 - 24
0.13 - 0.25
0.89 - 1.58
4.0
4
22 - 20
0.35 - 0.50
1.17 - 2.08
4.0
6
18 - 16
0.80 - 1.50
3.0
6.35
8
18 - 16
0.80 - 1.50
2.0 - 3.0
4.65
10
14
2.0
3.2
6.35
For other platings: See plating table.
Crimptooling table
Automatic crimp tooling for
contacts on strip
Size
Hand tools
die set included
24
20
16M(L)11
16M(L)1
14
Y16SCM2 (ratchet)
Y14MTV (ratchet)
Y16SCM2 (ratchet)
Y14SCM (ratchet)
Y14MTV (ratchet)
Y14SCM (ratchet)
Y14MTV (ratchet)
K750 ASC
(Stripper - crimper)
Mini Applicator
(not included)
M8ND
Die set
(not included)
N24RT11
N20RT29
P100 MAN
Mini Applicator
(not included)
MLS0318B
MLS0555A
N16RT26
MLS0356A
MLS16M11
N16RT24
MLS1579
MLS16M1
N14RT13
MLS1047
MLS14M1
For detailed information on crimp tooling : See crimp tooling section
85
Extraction
tooling
MLS20M1
RX2025GE1
or
RX2025GE2
or
RX16D11D1
SM/SC-M
Hand crimp tooling for loose contacts
RMDX/RCDX
Size 16 MULTIPIECE
coaxial contacts for
TRIM TRIO connectors
Description
Size 16 RMDX/RCDX Multipiece .063”
(1.6mm) diameter contacts are subminiature
coaxial contacts to cover a wide range of
subminiature coaxial and twisted pair
cables.
They are suitable in applications where a
mix of signal, power and coaxial cable
terminations for low frequency, shielded
signal and high frequency applications are
needed.
The contact consist of an inner pin/socket
and an outer male/female body.
The thermoplastic insulating bushing in the
outer body is designed to accept and
permanently retain the inner contact.
The outer ferrule hold the outer braid to the
outer contact and act as an insulating
support to ensure against bending and
vibrating stresses.
The inner and the outer conductor are
crimped individually, thereby enabling
inspection of both critical crimp points.
Features and benefits
• The inner and outer conductors are
crimped individually
• The thermoplastic insulating bushing in
the outer body is designed to accept and
permanently retain the inner contact.
• Outer ferrule hold the outer braid to the
outer contact and act as an insulating
support to ensure against bending and
vibration.
Construction
Connector accommodation
Inner and outer contacts: High conductive
copper alloy
Retaining spring: berylium copper
Insulating bushing: Polyamide 6.6
Any TRIM TRIO contact can be used in any
contact position in any connector in the
TRIM TRIO interconnection system.
• MS-M/ MSG Rectangular connectors
• SMS Qikmate
• G - Bantamate
• UT-Bantam
• UTG Metalok bantam
• UTP Full plastic bantam
• UTGS Shielded bantam
• MBG Bantamate II
Plating table
Retaining spring: Nickel plated
Inner and outer contacts:
D28: 0.75 µ Gold min. over Nickel
Performance characteristics
Operating voltage between
inner / outer contact:
230 VDC
Test potential between
inner / outer contact
750 VAC 1 min.
Operating temperature:
-55°C t0 +
125°C
Contact retention in body: 65 N min.
Contact voltage drop a 1A: 25m V max.
Isolation at 30 MHZ:
140 db.
How to order
RMDX
RCDX
Contact type:
RMDX = Male subminiature coax.
RCDX = Female subminiature coax.
Multipiece coax kit
K10 = Kit male coax.
K1 = Kit female coax
K10
K1
Plating indication
86
D28
D28
RMDX/RCDX
MULTIPIECE Subminiature coax - Male contact for coaxial cable
Contact for inner conductor
Type of
coaxial
cable
RG161U
RG179A/U
RG179B/U
RG187U
RG174/U
RG188/U
Amphenol
21-598
RG178A/U
RG196U
Inner female
contact
Part
number
Fig.
Crimp tool M10S1
Die Set
Stop
Bushing
Contact for outer braid
Outer male
contact
Part
number
Fig
S23D2
RFD26L1D28
2
SL46D2
RMDX602D28
1
Crimp tool M10S1
Hyring
Part
number
Fig
YOC074
4
YOC074
4
YOC074
+
RMDXB0553
4
Die
Set
Stop
Bushing
RX2025
GE1
S22-1
SL47-1
S26D2
S23D2
Extrac
tool
RX16D11
D1
3
Kit reference RMDXK10D28 includes RMDX602D28 + RFD26L1D28 + YOC074 + RMDXB0553 and are packed in plastic bag.
Contact for inner conductor
Type of
coaxial
cable
RG161U
RG179A/U
RG179B/U
RG187U
RG174/U
RG188/U
Amphenol
21-598
RG178A/U
RG196U
Inner male
contact
Part
number
Crimp tool M10S1
Fig.
Die Set
Stop
Bushing
RMDX/RCDX
MULTIPIECE Subminiature coax - Female contact for coaxial cable
Contact for outer braid
Outer female
contact
Part
number
Fig
Hyring
Crimp tool M10S1
Part
number
Fig
YOC074
4
YOC074
4
Die Set
Extrac
tool
Stop
Bushing
RX2025
GE1
S23D2
or
RMD26L1D28
2
S26D2
SL46D2
RCDX602D28
1
S22-1
SL47-1
RX16D11
D1
YOC074
+
RCDXB0551
S23D2
4
3
Kit reference RCDXK1D28 includes RCDX602D28 + RMD26L1D28 + YOC074 + RCDXB0551 and are packed in plastic bag.
87
RMDX/RCDX
MULTIPIECE Subminiature coax - Male contact for twisted pair cable
Contact for inner conductor
Type of
coaxial
cable
2 #24 solid
or stranded
2 #26 str
2 #24
7/0,20 str.
MIL-W-76 or
MIL-W-16878
type B
#28 per
MIL-W81822/3
Inner female
contact
Part
number
Fig.
RFD26L1D28
2
Crimp tool M10S1
Die set
S26D2
Stop
bushing
SL46D2
Contact for outer braid
Outer male
contact
Part
number
RMDX602D28
Fig
1
Crimp tool M10S1
Hyring
Part
number
Fig
YORX090
YOC074
RMDXB0553
4
5
3
YORX090
YOC074
RMDXB0554
4
5
3
YORX090
YOC074
RMDXB0553
4
5
3
Die set
Extrac
tool
Stop
bushing
RX2025
GE1
or
S221
SL471
RX16D11D1
MULTIPIECE Subminiature coax - Female contact for twisted pair cable
Contact for inner conductor
Type of
coaxial
cable
2 #24 solid
or stranded
2 #26 str
2 #24
7/0,20 str.
MIL-W-76 or
MIL-W-16878
type B
#28 per
MIL-W81822/3
Inner male
contact
Part
number
RMD26L1D28
Crimp tool M10S1
Fig.
2
Die set
S26D2
Stop
bushing
SL46D2
Contact for outer braid
Outer female
contact
Part
number
RCDX602D28
88
Fig
1
Crimp tool M10S1
Hyring
Part
number
Fig
YORX090
YOC074
RCDXB0551
4
5
3
YORX090
YOC074
RCDXB0552
4
5
3
YORX090
YOC074
RCDXB0551
4
5
3
Die set
Extrac
tool
Stop
bushing
RX2025
GE1
or
S221
SL471
RX16D11D1
RMDX/RCDX
Size 16 monocrimp
coaxial contacts for
TRIM TRIO connectors
Description
Size 16 RMDX/RCDX Monocrimp .063”
(1.6mm) diameter contacts are one-piece
monocrimp subminiature coaxial contacts
to cover a wide range of subminiature
coaxial and twisted pair cables.
They provide cost effective solutions in
applications where a mix of signal, power
and coaxial cable terminations for low
frequency, shielded signal and high
frequency applications are needed.
Monocrimp one piece coaxial contacts offer
high reliability plus the economic advantage
of a 95% reduction in installation time over
conventional assembly methods currently in
use.
Features and benefits
Performance characteristics
Operating voltage between
inner / outer contact:
230 VDC
Test potential between
inner / outer contact
450 VAC 1 min.
Operating temperature:
-55°C to +
125°C
Contact retention in body: 65 N min.
Contact voltage drop a 1A: 30m V max.
Isolation at 30 MHZ:
140 db.
Construction
Connector accommodation
Inner and outer contacts: High conductive
copper alloy
Retaining spring: berylium copper
Insulating bushing: Polyamide 6.6
Any TRIM TRIO contact can be used in any
contact position in any connector in the
TRIM TRIO interconnection system.
• MS-M/MSG Rectangular connectors
• SMS Qikmate
• G - Bantamate
• UT-Bantam
• UTG Metalok bantam
• UTP Full plastic bantam
• UTGS Shielded bantam
• MBG Bantamate II
Plating table
Retaining spring: Nickel plated
Inner and outer contacts:
D28: 0.75µ Gold min. over Nickel
RMDX/RCDX
• The monocrimp one-piece coaxial
contacts offer high reliability plus the
economic advantage of a 95% reduction
in installation time over conventional
assembly methods.
• This economy is achieved by
simultaneously crimping of both the inner
and outer conductor
How to order
RMDX60
RCDX60
Contact type:
RMDX = Male subminiature coax.
RCDX = Female subminiature coax.
Monocrimp design variation
Plating indication
89
36
36
D28
D28
RMDX/RCDX
MONOCRIMP Subminiature coax
Part number
Male
Female
RMDX6050D28
RCDX6050D28
RMDX6050D28
RCDX6050D28
RMDX6032D28
RCDX6032D28
RMDX6024D28
RCDX6024D28
RMDX6032D28
RCDX6032D28
RMDX6026D28
RCDX6026D28
RMDX6036D28
RCDX6036D28
RMDX6036D28
RCDX6036D28
RMDX6018D28
RCDX6018D28
RMDX6018D28
RCDX6018D28
Coax dimensions
AWG
inner
conduct.
Coax strip lengths
Crimp tool M10S1
G
A
Die set
0.30
5.1
8.9
S80
4.2
8.5
S87
11.7
S80
Cable
type
D
max
E
F
-
2.64
2.11
1.70
-
2.29
1.63
1.22
-
2.90
2.29
1.91
0.38
-
1.78
1.37
0.97
0.48
RG174/U
2.92
2.24
1.52
0.48
-
3.05
2.44
1.96
0.41
RG188A/U
2.79
RG316/U
2.72
B
C
not incl.
Extraction
stop
tool
bushing
not incl.
30
28
26
1.98
2.34
1.70
5.1
6.35
S80
0.51
11.7
0.53
8.9
SL105
1.27
0.64
* M10SG8 consists of die set, stop bushing and M10S1 tool
90
RX2025GE1
S82
OR
S80
RX16D11D1
1.52
2.62
26
S82
M10SG8*
crimping kit
RMDX/RCDX
MONOCRIMP Twisted pair
Part number
Male
Cable strip lenghts
Dia. outer
AWG
jacket
Female inner conduct. (single wire)
RMDX6019D28
RCDX6019D28
RMDX6031D28
RCDX6031D28
26 (19 x 0.10)
24 (7 x 0.20)
24 (19 x 0.13)
26 (7 x 0.16)
1.25
1.25
1.45
0.70
A
B
4.7
6.0
C
4.0
Crimp tool
M10S1
Die set
Stop
bushing
not incl.
not. incl.
M10SG8*
Crimping kit
S80
SL105
Extraction
tool
RX2025GE1
or
RX16D11D1
RMDX/RCDX
* M10SG8 consist of die set, stop bushing and M10S1 tool.
91
Fibre optic
contacts
Size 16 Fibre optic
contacts for
TRIM TRIO connectors
Description
Size 16 (1.6mm) Fibre optic contacts series
8012 are optical contacts designed for the
integration of optical links in all TRIM TRIO
cable connectors.
The F.O. contacts are designed to
accomodate 1000m plastic fibres with a
cable diameter of 2.2 mm.
Features and benefits
• Socket contact is spring loaded to avoid
any air gap between the two optical
faces.
• Low insertion loss is provided by high
precision pieces.
• Single jumpers, multiway harness and
active device housings can be supplied
according customer requirement.
Performance characteristics
for plastic fibre (depends on
supplier)
Temperatur range:
Attenuation at 0.660 µm
(at +20°C):
Min radius:
Tensile strength
Weight:
Cable retention:
Typical insertion loss
Construction
Connector accommodation
Contact body: Arcap (rustproof)
Outer spring: Stainless steel
Fibre optic contacts can be used in any
contact position in any connector in the
TRIM TRIO interconnection system.
• MS-M / MSGRectangular connectors
• SMS Qikmate
• G - Bantamate
• UT-Bantam
• UTG Metalok bantam
• UTP Full plastic bantam
• UTGS Shielded bantam
Tool kit
Separate tools
Crimping / polishing technic
•
•
•
•
•
•
•
•
-20°C to + 70°C
< 200 db/Km
25 mm
5 daN
5 daN/Km
25 N
1.5 dB at 650 nm
How to order
Contacts
Male contact:
Female contact:
8012P14J262
8012S14J262
The tool kit contains all necessary tools to
terminate contacts for plastic fibre, such as
• Stripping plier
• Crimping plier
• Polishing plate and tool
• Miscallaneous
Part number tool kit: 80MS0004
For other fibres consult factory.
92
Cutting tool
Stripping plier
Crimping plier
Polishing plate
Polishing tool
10 polishing discks 30 µm
10 polishing discks 9 µm
Extraction tool
80WD0005
80WD0025
80WS0002
80WP0005
80WP0018
80WP0019
80WP0014
RX2025GE1
Accessories
Discrimination keys for
TRIM TRIO connectors
Description
In applications where similar connectors are
used next to each other, mismatching can
be a reason for disturbances, system failure
or even danger to operating personnel.
To eliminate mismatching, all TRIM TRIO
connectors can be equipped with
discrimination keys, which offer unlimited
possibilities for a “fool - proof”
interconnection system.
When one of these discrimination keys is
used, the TRIM TRIO connector will only
mate with a connector which has a vacant
contact or discrimination cavity at the
corresponding position.
This system offers boundless opportunities
for all applications which involve several
identical TRIM TRIO connectors.
The material used is polyamide 6.6
SMSPKE0
ACCESSORIES - TOOLING
A dummy contact, which can be inserted into an empty contact cavity in any of the TRIM TRIO connectors.
SMSPKB2
A tube, which can be fitted over a preassembled male contact in all TRIM TRIO male boardmount connectors MSO, SMS, MSG.
93
Accessories
SMSPKE2V1
A pin, which can be inserted into a preassambled female contact in all TRIM TRIO female boardmount connectors MSO, SMS.
SMSPKE3
A pin, Which can be inserted in the discrimination cavities of the SMS Qikmate cable and boardmount connectors. The discrimination cavities
are in between of the contact cavities and offer the advantage that no contact cavities are lost due to discrimination.
As extraction tool, the RX2025GE1 without the “extraction tool tip” can be used.
To unlock the discrimination pin, insert the extraction tool in the discrimination cavity at the rear side of the connector. Meanwhile, the pin can
be extracted manually at the mating side.
94
Tooling - intro
Overview TRIM TRIO tooling
ACCESSORIES - TOOLING
Selection matrix TRIM TRIO tooling
95
Crimptooling
Crimptooling for TRIM TRIO
contacts
The TRIM TRIO connection system not only offers versatility in
connectors but production versatility in tooling as well.
All information needed on tooling ranges from simple handtools for
small production, over semi-automatic to full automatic strip-andcrimp machines can be found on the hereafter paragraphs.
All the TRIM TRIO tooling and this for machined, stamped and
formed and coax contacts, is specially designed for this system to
make reliable, trouble-free connections.
Weight:
Length:
425 gr.
250 mm.
M10S1 - for machined contacts
A robust, versatile, full cycling handtool which is fully qualified to the
requirements of MIL-C-22520. Interchangeable 4-indent die sets are
available for a wide range of machined contacts and gives a
simultaneous crimp on both wire and insulation.
This tool is suitable for application of RM/RC machined
contacts and coaxial from the TRIM TRIO range.
Weight:
Length:
400 gr.
205 mm.
Weight:
Length:
300 gr.
170 mm.
Y16RCM - for machined contacts
MH860 - for machined contacts
A light weight, low cost crimptool with fixed, 3-groove die set to
crimp Size 16 TRIM TRIO RM/RC loose piece machined
contacts.
The tool is ratchet controlled to guarantee a complete crimp cycle.
Each crimptool is supplied with a locator to guarantee a perfect
crimp indent positioning.
A light weight crimptool Qualified to MIL-C-22520/7 that gives an 8
impression crimp with a precision cycle-controlled ratcheting
mechanism. It features an 8 step crimp-depth selector knob and is
designed to crimp Size 16 TRIM TRIO RM/RC loose piece
machined contacts. The tool can be provided with different
locators heads to crimp different contact types.
96
Crimptooling
800 gr.
275 mm.
Weight:
Length:
400 gr.
230 mm.
M8ND - for machined and formed contacts
Y14MTV - for formed contact
A robust full cycling hand ratchet tool which utilises interchangeable
“N” die sets to crimp
Size 16 TRIM TRIO RM/RC loose piece machined contacts.
Size 16 TRIM TRIO SM-M/SC-M loose piece formed contacts.
A light weight crimptool with fixed 3-groove die set for AWG26 to 14
for: Size 16 TRIM TRIO SM-M/SC-M loose piece formed
contacts.
Ratchet controlled to guarantee a complete crimp cycle.
Weight:
Length:
400 gr.
205 mm
Weight:
Length:
400 gr.
205 mm.
Y16SCM2 - for formed contacts
Y14SCM - for formed contacts
A light weight crimptool with fixed 3-groove die set for AWG26 to 16
for:
Size 16 TRIM TRIO SM-M/SC-M loose piece formed contacts.
Ratchet controlled to guarantee a complete crimp cycle.
Each crimptool is supplied with a locator to guarantee a perfect
crimp indent
positioning.
A light weight crimptool with fixed 3-groove die set for AWG18 to 14
for:
Size 16 TRIM TRIO SM-M/SC-M loose piece formed contacts.
Ratchet controlled to guarantee a complete crimp cycle.
Each crimptool is supplied with a locator to guarantee a perfect
crimp indent positioning.
97
ACCESSORIES - TOOLING
Weight:
Length:
Crimptooling
K750ASC
Stripper / Crimper
machine for Trim Trio
contacts.
Description
The Strip Crimp 750 processes all banded
contacts with cross sections from 0.05 –
4.0 mm2.
The press has a 40mm stroke and can be
used with all UNI-C applicators as well as
side-feed mini-style applicators.
Built with well proven precision mechanics
and state of the art electronics, the machine
is extremely user friendly. One example is
the graphic display from which all stripping
parameters can be set and called up
digitally.
Up to 254 different wire programs can be
stored in the memory.
Precision stripping and gas tight crimps
guarantee maximum processing quality.
Ref.:
Power.:
Weight:
Dimensions:
K750ASC
0.37 kWatt
85 kg
350x460x485
P100MAN (TT Press)
MLS--- Left side miniapplicator
This electromechanical high speed full automatic crimping press is
specially designed for mass production and is realised totally in
assembled steel parts.
The available force consents the crimping of a wire section up to
2.5mm2.
The press has a 40mm stroke and can be used together with side
feed mini-style applicators.
The noise level of the press is less than 70dB.
There is a safety mechanism that stops the press if the working
speed is too high or the press does not complete its cycle. This
protects the press or equipment mounted on board from damage.
Miniapplicatorsn to crimp machined or stamped and formed TRIM
TRIO contacts.
All the adjustments requested to make tool correctly functioning
(crimp feeding pitch, crimp height...) can be simply made.
Resolution of 0.03mm. Regulation range from 0 to 2.7 mm.
Ref.:
Stroke:
Weight:
Dimensions:
See contact sections
40 mm
4.5 kg
145x107x150
Options
Ref.:
Power.:
Weight:
Dimensions:
P100MAN
0.75 kWatt
41 kg
200x300x580
1 - Quality assurance for crimping technology...
A crimping force sensor continuously checks the quality of each individual
crimp and records it without impairing the processing speed. The sensor
detects bad crimp connections, eliminating the high subsequent costs
otherwise caused by them.
For ordering consult factory
98
Crimptooling
Extraction tooling
RX2025GE1
RX2025GE2
A spring loaded extraction tool for the full range of TRIM TRIO
contacts. This tool ensures that the contact locking louvres are fully
retracted before any pressure is applied to extract a contact.
A low cost spring loaded extraction tool for the full range of TRIM
TRIO contacts.
RX16D11D1
How to extract a contact out of its cavity?
A spring loaded extraction tool for the full range of TRIM TRIO
contacts. This tool ensures that the contact locking louvres are fully
retracted before any pressure is applied to extract a contact. It is
especially suitable for applications where the integrity of the
assemblies are of the utmost importance.
Slide the extraction tip over contact from mating side till the locking
spring from the contact is depressed.
Push on handle to push out the contact with the spring loaded inner
plunger.
RTM205
This tool is especially designed to ease insertion of any TRIM TRIO
contact crimped on very flexible or small wire sizes. Simply position
the insertion tool so that the tip of the tool bears against the back of
the wire barrel, retaining the wire with thumb in the groove of the
tool. Push the contact slowly into the connector until it snaps into
position.
99
ACCESSORIES - TOOLING
Insertion tooling
Specials - TRIM TRIO
TRIM TRIO
Special connectors :
• Mixed power / signal
• VDE versions
• Boardmount versions
• Drawer connectors
• High temperatures
• Special applications
• Customised connectors
Description
Special connectors are connectors to meet
application-specific requirements.
Based upon design-in projects, this range of special
connectors is an extension of the long established and
popular TRIM TRIO connector series shown in this
catalog, but with the advantage of offering a number
of additional features.
Features and benefits
• TRIM TRIO connectors suitable for mixed power /
signal application.
• TRIM TRIO connectors with preloaded stamped and
formed contacts for boardmount application
• TRIM TRIO connectors for drawer applications and
high temperature.
• Design-in flexibility of TRIM TRIO
The next page lists some of the Special TRIM TRIO connector configurations.
It is intended to give you a general idea of our design capabilities.
As the creation of Special TRIM TRIO connectors is an ongoing process, we advise you to contact our
nearest FCI sales office if you have specific connector needs.
Our design flexibility is virtually unlimited, so we are always willing to consider any customised design.
Separate data sheets with more detailed technical info of the listed TRIM TRIO Specials are available.
100
• UTG 24-7 mixed power with 7 power and
2 std. Trim Trio contacts – up to 44 Amps
• UTG 12-3 with 3 power contacts
up to 26 Amps
• UTG 24-11 with 4 power and 7 standard
Trim Trio contacts – up to 44 Amps
• UTG 14-8 with 4 power and 4 standard
Trim Trio contacts – up to 26 Amps
• SMS12 with 8 power and 4 standard
Trim Trio contacts - Up to 26 Amps
• Power crimp contacts
– dia 2,4 - up to 26 Amps
– dia 3,6 - up to 44 Amps
• MS75 with die cast hood and integrated
shroud, for standard Trim Trio contacts
• QIKRACK Modular drawer connector
For standard and RCS Trim Trio contacts
101
ACCESSORIES - TOOLING
Specials - TRIM TRIO
Notes
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
............................................................................................................................................................................................................
102
AUSTRALIA
CHINA
ITALY
MALAYSIA
FCI Connectors Australia
5 Tarlington Place
Smithfield NSW 2164
Tel. : 61 - 2 9725 5288
Fax : 61 - 2 9725 5204
e-mail : [email protected]
FCI Shenzhen
Room 813A, 8/F, Shenzhen Kerry Centre
Renminan Lu, Shenzhen 518001
P.R. China
Tel. : 86 - 755 518 1732
Fax : 86 - 755 518 1730
e-mail : [email protected]
Framatome Connectors Italia
Strada del Francese 137
10156 TORINO
Tel. : 39 - (11) 451 9611
Fax : 39 - (11) 470 2266
e-mail : [email protected]
FCI Penang
7-02, Wisma Pantai Building
Jalan Wisma Pantai
12200 Butterworth - Penang
Tel. : 6 - 04 323 4511
Fax : 6 - 04 323 4513
e-mail : [email protected]
FRANCE
JAPAN
FCI France
145 rue Yves le Coz
78035 VERSAILLES Cedex
Tel. : 33 - 1 39 49 21 83
Fax : 33 - 1 39 49 20 00
e-mail : [email protected]
NETHERLANDS
FCI Japan
28-10 Minami Ooi 3-Chome
Shinagawa-ku, Tokyo 140-8581
Tel. : 81 - 3 5493 5200
Fax : 81 - 3 5493 5238
e-mail : [email protected]
FCI Nederland
Essebaan 7
2908 LJ CAPELLE A/D IJSSEL
Tel. : 31 - 10 264 3333
Fax : 31 - 10 264 3399
e-mail : [email protected]
FCI Belgium
48 A rue Stroobants
B-1140 Brussels
Tel. : 32 - 2 247 99 00
Fax : 32 - 2 247 99 99
e-mail : [email protected]
BRASIL
FCI Brazil
Estrada do Guarapiranga 2400
Santo Amaro
04901-905 SÃO PAULO-SP
Tel. : 55 - (11) 55 15 7200
Fax : 55 - (11) 55 15 7151
e-mail : [email protected]
CANADA
FCI Canada
1530 Birchmount Road
SCARBOROUGH - ONTARIO M1P
2G9
Tel. : 1 - (717) 767 8000
Fax : 1 - (717) 767 8052
e-mail : [email protected]
CHINA
FCI Beijing
Unit 1412, Beijing COFCO Plaza Tower B
No. 8, Jianguomennei Daijie
Dong Cheng District
Beijing 100005, P.R. China
Tel. : 86 - 10 6526 3802
Fax : 86 - 10 6526 3805
e-mail : [email protected]
CHINA
FCI Hong Kong
AIA Tower New World Centre
20 Salisbury Road, Tsim Sha Tsui
Kowloon, Hong Kong
Tel. : 852 - 2510 8131
Fax : 852 - 2510 7743
e-mail : [email protected]
GERMANY
Framatome Connectors Deutschland
AM Kronberger Hang 51
65824 SCHWALBACH
Tel. : 49 -(0) 6196 / 9520-0
Fax : 49 -(0) 6196 / 9520-111
e-mail : [email protected]
GREAT BRITAIN
Framatome Connectors UK
Connector House
Eyncourt Road - Woodside Estate
DUNSTABLE Beds. LU5 4TS
Tel. : 44 - 1 582 814 800
Fax : 44 - 1 582 814 814
e-mail : [email protected]
INDIA
Framatome Connectors OEN
Thykoodam, Vyttila
Cochin 682 019 KERALA
Tel. : 91 - 484 303 028
Fax : 91 - 484 304 279
e-mail : [email protected]
INDONESIA
Framatome Connectors Indonesia
MEDCO Building, Ground Floor
Jl Ampera Raya, No. 20, Cilandak
Jakarta 12560
Tel. : 62 - 21 780 0824
Fax : 62 - 21 780 1560
e-mail : [email protected]
KOREA
FCI Korea
Room 301, Kyemyung Building 165-4
Samsung Dong, Kangnam Ku
Seoul 135090
Tel. : 82 - 2 562 8474
Fax : 82 - 2 562 8475
e-mail : [email protected]
MEXICO
FCI Mexico
Calle 5 No. 104 Parque Industrial
Toluca 2000
C.P. 50200 Toluca
EDO DE MEXICO APDO Postal 532
Tel. : 52 - (72) 754 300
Fax : 52 - (72) 799 240
e-mail : [email protected]
MALAYSIA
FCI Kuala Lumpur
Suite 2401, 24th Floor
Plaza See Hoy Chan, Jin Raja Chulan
50200 Kuala Lumpur
Tel. : 6 - 03 232 6792
Fax : 6 - 03 232 6792
e-mail : [email protected]
SINGAPORE
FCI Asia
391B Orchard Road
# 18-00 Ngee Ann City
Singapore 238874
Tel. : 65 - 549 6600
Fax : 65 - 738 6311
e-mail : [email protected]
SPAIN
FCI Connectors España
Poligono Industrial
08781 St. Esteve Sesrovires
Tel. : 34 - (93) 771 4012
Fax : 34 - (93) 771 3197
e-mail : [email protected]
SWEDEN
FCI Connectors Sweden
Sjövicksbacken 12
Box 47084 100 74 Stockholm
Tel. : 46 - (8) 685 5300
Fax : 46 - (8) 685 5355
e-mail : [email protected]
SWITZERLAND
FCI Switzerland
Sihlbruggstrasse 144
6340 BAAR
Tel. : 41 - (41) 760 1434
Fax : 41 - (41) 761 0647
e-mail : [email protected]
CHINA
TAIWAN
FCI Shanghaï
Room 9008, Yong xin Mansion
887 Huai Mid Road
Shanghai 200020, P.R. China
Tel. : 86 - 21 6474 7807
Fax : 86 - 21 6467 4329
e-mail : [email protected]
FCI Taiwan
No. 7-1 Tsu-Chiang 1st Road
Chung Li industrial Zone,
Chung Li, Taoyuan, Taiwan 320
Republic of China
Tel. : 886 - 3 452 4300
Fax : 886 - 3 451 5371
e-mail : [email protected]
CHINA
FCI Shenyang
No. 64-562, 8 Jing Street
Heping District, Shenyang 110003
P.R. China
Tel. : 86 - 24 2270 4873
Fax : 86 - 24 2270 4873
e-mail: [email protected]
USA
B (F) T TRIO 0602 E
FCI USA
25 Grumbacher Road
York, Pennsylvania 17 402
Tel. : 1(717) 767 67 05
Fax : 1(717) 505 59 41
© Copyright Framatome Connectors International, S.A. All rights reserved
BELGIUM
http://www.fciconnect.com