TI LM107-N

LM107,LM207,LM307
LM107 LM207 LM307 Operational Amplifiers
Literature Number: SNOSBS4A
LM107/LM207/LM307 Operational Amplifiers
General Description
Connection Diagrams
Features
Y
Y
Y
Y
Offset voltage 3 mV maximum over temperature
Input current 100 nA maximum over temperature
Offset current 20 nA maximum over temperature
Guaranteed drift characteristics
et
Dual-in-Line Package
bs
ol
Metal Can Package
tors. Further, replacing circuits where matched transistor
pairs buffer the inputs of conventional IC op amps, it can
give lower offset voltage and drift at a lower cost.
The LM107 is guaranteed over a b55§ C to a 125§ C temperature range, the LM207 from b25§ C to a 85§ C and the
LM307 from 0§ C to a 70§ C.
e
The LM107 series are complete, general purpose operational amplifiers, with the necessary frequency compensation
built into the chip. Advanced processing techniques make
the input currents a factor of ten lower than industry standards like the 709. Yet, they are a direct, plug-in replacement for the 709, LM101A and 741.
The LM107 series offers the features of the LM101A, which
makes its application nearly foolproof. In addition, the device provides better accuracy and lower noise in high impedance circuitry. The low input currents also make it particularly well suited for long interval integrators or timers, sample and hold circuits and low frequency waveform genera-
TL/H/7757 – 2
Note: Pin 4 connected to case.
Top View
TL/H/7757 – 3
Top View
Order Number LM107H/883*
See NS Package Number H08C
Order Number LM107J/883* or LM207J
See NS Package Number J08A
Order Number LM307N
See NS Package Number N08A
O
Dual-in-Line Package
TL/H/7757 – 13
Order Number LM107J-14/883*
See NS Package Number J14A
*Available per SMDÝ 5962-8958901.
C1995 National Semiconductor Corporation
TL/H/7757
RRD-B30M115/Printed in U. S. A.
LM107/LM207/LM307 Operational Amplifiers
December 1994
Absolute Maximum Ratings
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
(Note 4)
Supply Voltage
Power Dissipation (Note 1)
Differential Input Voltage
Input Voltage (Note 2)
Output Short Circuit Duration
Operating Temperature Range (TA)
(LM107)
(LM207)
Storage Temperature Range
Lead Temperature (Soldering, 10 sec)
LM107/LM207
g 22V
500 mW
g 30V
g 15V
Continuous
LM307
g 18V
500 mW
g 30V
g 15V
Continuous
b 55§ C to a 125§ C
b 25§ C to a 85§ C
b 65§ C to a 150§ C
0§ C to a 70§ C
b 65§ C to a 150§ C
260§ C
260§ C
TMIN
TMAX
b 55§ C
b 25§ C
a 125§ C
a 85§ C
a 70§ C
LM107
LM207
LM307
0§ C
ESD rating to be determined.
Electrical Characteristics (Note 3)
LM107/LM207
Conditions
Min
LM307
Units
e
Parameter
Typ
Max
Min
Typ
Max
TA e 25§ C, RS s 50 kX
0.7
2.0
2.0
7.5
mV
Input Offset Current
TA e 25§ C
1.5
10
3.0
50
nA
Input Bias Current
TA e 25§ C
30
75
70
250
nA
Input Resistance
TA e 25§ C
Supply Current
TA e 25§ C
VS e g 20V
VS e g 15V
TA e 25§ C, VS e g 15V
VOUT e g 10V, RL t 2 kX
Input Offset Voltage
RS s 50 kX
1.5
4.0
1.8
2.0
50
160
25
3.0
15
Average Temperature
Coefficient of Input
Offset Current
25§ C s TA s TMAX
TMIN s TA s 25§ C
0.01
0.02
0.1
0.2
TA e a 125§ C, VS e g 20V
1.2
O
100
2
2.5
mA
mA
V/mV
10
mV
6.0
30
mV/§ C
70
nA
0.01
0.02
0.3
0.6
nA/§ C
nA/§ C
20
Input Bias Current
3.0
160
3.0
Input Offset Current
MX
3.0
1.8
Average Temperature
Coefficient of Input
Offset Voltage
Supply Current
0.5
bs
ol
Large Signal Voltage
Gain
et
Input Offset Voltage
300
nA
mA
Electrical Characteristics (Note 3) (Continued)
Parameter
LM107/LM207
Conditions
Min
Large Signal Voltage
Gain
Output Voltage Swing
Input Voltage Range
VS e g 15V, VOUT e g 10V
RL t 2 kX
VS
RL
RL
e g 15V
e 10 kX
e 2 kX
VS e g 20V
VS e g 15V
Typ
LM307
Max
Min
Typ
Units
Max
15
25
V/mV
g 12
g 14
g 12
g 14
g 10
g 13
g 10
g 13
a 15
b 13
g 12
a 15
b 13
V
V
g 15
V
V
Common Mode
Rejection Ratio
RS s 50 kX
80
96
70
90
dB
Supply Voltage
Rejection Ratio
RS s 50 kX
80
96
70
96
dB
e
Note 1: The maximum junction temperature of the LM107 is 150§ C, and the LM207/LM307 is 100§ C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 165§ C/W, junction to ambient, or 30§ C/W, junction to case. The thermal resistance of the dual-in-line
package is 100§ C/W, junction to ambient.
Note 2: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 3: These specifications apply for g 5V s VS s a 20V and b 55§ C s TA s a 125§ C for the LM107 or b 25§ C s TA a 85§ C for the LM207, and 0§ C s TA s
a 70§ C and g 5V s VS s g 15V for the LM307 unless otherwise specified.
O
bs
ol
Schematic Diagram*
et
Note 4: Refer to RETS107X for LM107H and LM107J military specifications.
*Pin connections shown are for metal can.
TL/H/7757 – 1
3
Guaranteed Performance Characteristics LM107/LM207
Input Voltage Range
Output Swing
Voltage Gain
TL/H/7757 – 4
Guaranteed Performance Characteristics LM307
Output Swing
Voltage Gain
et
e
Input Voltage Range
bs
ol
TL/H/7757 – 5
Typical Performance Characteristics
O
Supply Current
Current Limiting
Voltage Gain
Input Current
Input Noise Voltage
Input Noise Current
TL/H/7757 – 6
4
Typical Performance Characteristics
Open Loop
Frequency Response
(Continued)
Large Signal
Frequency Response
Voltage Follower
Pulse Response
TL/H/7757 – 7
Typical Applications**
RIN e R1
R2
VIN
R1
et
VOUT e b
Non-Inverting AC Amplifier
e
Inverting Amplifier
VOUT e
R1 a R2
VIN
R1
RIN e R3
TL/H/7757 – 8
bs
ol
R3 e R1//R2
Non-Inverting Amplifier
VOUT e
R1 a R2
VIN
R1
O
TL/H/7757 – 10
**Pin connections shown are for metal can.
5
TL/H/7757 – 9
Typical Applications** (Continued)
Turntable Notch Filter
R1 e R2 e R3
R4 e R5 e
fo e
R1
2
1
2q0C1 C2 R4 R5
et
e
e 60 Hz
TL/H/7757 – 11
O
bs
ol
Differential Input Instrumentation Amplifier
TL/H/7757 – 12
**Pin connections shown are for metal can.
6
7
e
et
bs
ol
O
et
e
Physical Dimensions inches (millimeters)
O
bs
ol
Metal Can Package (H)
Order Number LM107H/883
NS Package Number H08C
8
et
e
Physical Dimensions inches (millimeters) (Continued)
O
bs
ol
Ceramic Dual-In-Line Package (J)
Order Number LM107J/883 or LM207J
NS Package Number J08A
Ceramic Dual-In-Line Package (J)
Order Number LM107J-14/883
NS Package Number J14A
9
e
et
LM107/LM207/LM307 Operational Amplifiers
Physical Dimensions inches (millimeters) (Continued)
bs
ol
Molded Dual-In-Line Package (N)
Order Number LM307N
NS Package Number N08E
LIFE SUPPORT POLICY
O
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated