4-Channel ESD/EMI Filter Array Plus 4-Channel ESD Array for USB CM1401-32CP Features • • • • • • • • • • • Functionally and pin-compatible with CSPEMI307A device OptiGuard coated for improved reliability at assembly Four channels of combined EMI/RFI filtering + ESD protection Four additional channels of ESD-only protection 40dB absolute attenuation (typical) at 1GHz 35dB attenuation (typical) at 1GHz relative to pass band ±15kV ESD protection on all channels (IEC 61000-4-2 Level 4, contact discharge) ±30kV ESD protection on all channels (HBM) 15-bump, 2.960mm X 1.330mm footprint Chip Scale Package (CSP) features extremely low lead inductance for optimum filter and ESD performance RoHS-compliant (lead-free) finishing Applications • • • • • • • EMI filtering and ESD protection for both data and I/O ports Outer four channels provide ESD protection for USB lines and other I/O port applications Wireless handsets Handheld PCs / PDAs MP3 players Notebooks Desktop PCs ©2010 SCILLC. All rights reserved. June 2010 Rev. 0 Product Description The CM1401-32CP is a multichannel array with four low-pass filter + ESD channels and four ESD-only channels. The CM1401-32CP reduces EMI/RFI emissions on a data port and protects against ESD on a USB port. Each EMI/RFI channel integrates a high quality pi-style filter (C-R-C) that provides greater than 30dB attenuation in the 800-2700 MHz range relative to the pass band attenuation. These pi-style filters are bidirectional, controlling EMI both to and from a data port connector. The CM1401-32CP provides a high-level of ESD protection on all eight channels for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The input pins safely dissipate ESD strikes of ±15kV, exceeding the maximum requirement of the IEC 61000-4-2 international standard. Using the MIL-STD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the device provides protection for contact discharges to greater than ±30kV. The CM1401-32CP is particularly well suited for portable electronics (e.g., cellular telephones, PDAs, notebook computers) because of its small package footprint and low weight. The CM1401-32CP incorporates OptiGuard™ coating for improved reliability at assembly and comes in a space-saving, low-profile Chip Scale Package with RoHS-compliant lead-free finishing. Publication Order Number: CM1401-32CP/D CM1401-32CP Rev. P2 | Page 2 of 12 | www.onsemi.com CM1401-32CP PIN DESCRIPTIONS PIN(s) NAME DESCRIPTION A1 ESD_1 ESD Channel 1 A2 FILTER+ESD_1 Filter + ESD Channel 1 A3 FILTER+ESD_2 Filter + ESD Channel 2 A4 FILTER+ESD_3 Filter + ESD Channel 3 A5 FILT ER+ESD_4 Filter + ESD Channel 4 A6 ESD_2 ESD Channel 2 B1-B3 GND Device Ground C1 ESD_3 ESD Channel 3 C2 FILTER+ESD_1 Filter + ESD Channel 1 C3 FILTER+ESD_2 Filter + ESD Channel 2 C4 FILTER+ESD_3 Filter + ESD Channel 3 C5 FILTER+ESD_4 Filter + ESD Channel 4 C6 ESD_4 ESD Channel 4 Ordering Information PART NUMBERING INFORMATION Pins Package Variation Ordering Part Number1 Part Marking 15 CSP SAC387 CM1401-32CP N012A Note 1: Parts are shipped in Tape and Reel form unless otherwise specified. Rev. P2 | Page 3 of 12 | www.onsemi.com CM1401-32CP Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS -65 to +150 °C DC Power per Resistor 100 mW DC Package Power Rating 600 mW RATING UNITS -40 to +85 °C Storage Temperature Range STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range Rev. P2 | Page 4 of 12 | www.onsemi.com CM1401-32CP ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE1) SYMBOL PARAMETER R Resistance C Capacitance CONDITIONS At 2.5V DC TCR Temperature Coefficient of Resistance TCC Temperature Coefficient of Capacitance VDIODE MIN TYP MAX UNITS 80 100 120 Ω 24 30 36 pF 1200 ppm/°C At 2.5V DC -300 ppm/°C Diode Voltage (reverse bias) IDIODE=10μA 6.0 V ILEAK Diode Leakage Current (reverse bias) VDIODE=3.3V VSIG Signal Voltage Positive Clamp Negative Clamp ILOAD = 10mA In-system ESD Withstand Voltage a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 Level 4 Note 3 Clamping Voltage during ESD Discharge MIL-STD-883 (Method 3015), 8kV Positive Transients Negative Transients Notes 2 and 3 Cut-off Frequency ZSOURCE=50Ω, ZLOAD=50Ω R=100Ω, C=30pF VESD VCL f C 5.6 -1.5 6.8 -0.8 100 nA 9.0 -0.4 V V ±30 kV ±15 kV +10 -5 V V 58 MHz Note 1: TA=25°C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin. For example, if ESD is applied to Pin A2, then clamping voltage is measured at Pin C2. Rev. P2 | Page 5 of 12 | www.onsemi.com CM1401-32CP Performance Information Typical Filter Performance (TA=25°C, DC Bias=0V, 50 Ohm Environment) Figure 1. Insertion Loss vs. Frequency (A1-C1 to GND B2) Figure 2. Insertion Loss vs. Frequency (A2-C2 to GND B2) Rev. P2 | Page 6 of 12 | www.onsemi.com CM1401-32CP Performance Information (cont’d) Typical Filter Performance (TA=25°C, DC Bias=0V, 50 Ohm Environment) Figure 3. Insertion Loss vs. Frequency (A3-C3 to GND B2) Figure 4. Insertion Loss vs. Frequency (A4-C4 to GND B2) Rev. P2 | Page 7 of 12 | www.onsemi.com CM1401-32CP Performance Information (cont’d) Typical Filter Performance (TA=25°C, DC Bias=0V, 50 Ohm Environment) Figure 5. Comparison of Filter Response Curves for CM1400-32CP with DC Bias Rev. P2 | Page 8 of 12 | www.onsemi.com CM1401-32CP Performance Information (cont’d) Figure 6. Filter Capacitance vs. Input Voltage over Temperature (normalized to capacitance at 2.5VDC and 25°C) Figure 7. Resistance vs. Temperature (normalized to resistance at 25°C) Rev. P2 | Page 9 of 12 | www.onsemi.com CM1401-32CP Application Information PARAMETER VALUE Pad Size on PCB 0.240mm Pad Shape Round Pad Definition Non-Solder Mask defined pads Solder Mask Opening 0.290mm Round Solder Stencil Thickness 0.125mm - 0.150mm Solder Stencil Aperture Opening (laser cut, 5% tapered walls) 0.300mm Round Solder Flux Ratio 50/50 by volume Solder Paste Type No Clean Pad Protective Finish OSP (Entek Cu Plus 106A) Tolerance — Edge To Corner Ball +50μm Solder Ball Side Coplanarity +20μm Maximum Dwell Time Above Liquidous (183°C) Maximum Soldering Temperature for Lead-free Devices using a Lead-free Solder Paste Non-Solder Mask Defined Pad 0.240mm DIA. Solder Stencil Opening 0.300mm DIA. Solder Mask Opening 0.290mm DIA. Figure 1. Recommended Non-Solder Mask Defined Pad Illustration Figure 2. Lead-free (SnAgCu) Solder Ball Reflow Profile Rev. P2 | Page 10 of 12 | www.onsemi.com 60 seconds 260°C CM1401-32CP Mechanical Details CSP Mechanical Specifications The CM1401-32CP is supplied in a custom Chip Scale Package (CSP). Dimensions are presented below. PACKAGE DIMENSIONS Package Custom CSP Bumps 15 Millimeters Inches Dim Min Nom Max Min Nom Max A1 2.915 2.960 3.005 0.1148 0.1165 0.1183 A2 1.285 1.330 1.375 0.0506 0.0524 0.0541 B1 0.495 0.500 0.505 0.0195 0.0197 0.0199 B2 0.245 0.250 0.255 0.0096 0.0098 0.0100 B3 0.430 0.435 0.440 0.0169 0.0171 0.0173 B4 0.430 0.435 0.440 0.0169 0.0171 0.0173 C1 0.180 0.230 0.280 0.0071 0.0091 0.0110 C2 0.180 0.230 0.280 0.0071 0.0091 0.0110 D1 0.575 0.644 0.714 0.0226 0.0254 0.0281 D2 0.368 0.419 0.470 0.0145 0.0165 0.0185 # per tape and reel Package Dimensions for CM1401-32CP Chip Scale Package 3500 pieces Controlling dimension: millimeters Rev. P2 | Page 11 of 12 | www.onsemi.com CM1401-32CP CSP Tape and Reel Specifications PART NUMBER CHIP SIZE (mm) POCKET SIZE (mm) B0 X A0 X K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 CM1401-32CP 2.96 X 1.33 X 0.644 3.10 X 1.45 X 0.74 8mm 178mm (7") 3500 4mm 4mm Figure 12. Tape and Reel Mechanical Data ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 Rev. P2 | Page 12 of 12 | www.onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative