DS42MB200
www.ti.com
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
DS42MB200 Dual 4.25 Gbps 2:1/1:2 CML Mux/Buffer with Transmit Pre-Emphasis and
Receive Equalization
Check for Samples: DS42MB200
FEATURES
DESCRIPTION
•
•
•
•
The DS42MB200 is a dual signal conditioning 2:1
multiplexer and 1:2 fan-out buffer designed for use in
backplane
redundancy
applications.
Signal
conditioning features include input equalization and
programmable output pre-emphasis that enable data
communication in FR4 backplanes up to 4.25 Gbps.
Each input stage has a fixed equalizer to reduce ISI
distortion from board traces.
1
2
•
•
•
•
•
•
1– 4.25 Gbps Fully Differential Data Paths
Fixed Input Equalization
Programmable Output Pre-emphasis
Independent Switch and Line Side Preemphasis Controls
Programmable Switch-side Loopback Mode
On-chip Terminations
+3.3V Dupply
ESD Rating HBM 6 kV
Lead-less WQFN-48 Package
(7mmx7mmx0.8mm, 0.5mm Pitch)
–40°C to +85°C Operating Temperature Range
All output drivers have 4 selectable steps of preemphasis to compensate for transmission losses from
long FR4 backplanes and reduce deterministic jitter.
The pre-emphasis levels can be independently
controlled for the line-side and switch-side drivers.
The internal loopback paths from switch-side input to
switch-side output enable at-speed system testing. All
receiver inputs are internally terminated with 100Ω
differential terminating resistors. All driver outputs are
internally terminated with 50Ω to VCC.
APPLICATIONS
•
•
•
Backplane Driver or Cable Driver
Redundancy and Signal Conditioning
Applications
XAUI
Functional Block Diagram
LO_0 ±
EQ
SIA_0 ±
EQ
SIB_0 ±
PRE_L
MUX_S0
LB0A
Port 0
SOA_0 ±
PRE_S
LI_0 ±
SOB_0 ±
EQ
PRE_S
LO_1 ±
LB0B
EQ
SIA_1 ±
EQ
SIB_1 ±
PRE_L
MUX_S1
LB1A
Port 1
SOA_1 ±
PRE_S
LI_1 ±
SOB_1 ±
EQ
PRE_S
PreL_0
PreL_1
PreS_0
PreS_1
Pre-emphasis
Control
PRE_L
PRE_S
LB1B
VCC
GND
RSV
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
DS42MB200
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
www.ti.com
Simplified Block Diagram
VCC
DS42MB200
1.5V
50
50
SIA_0+
50
50
LO_0+
LO_0-
Input stage
+EQ
M
U
X
CML
driver
SIA_0-
SIB_0+
Input stage
+EQ
SIB_0-
PRE_L
1.5V
50
50
MUX_S0
VCC
PORT 0
LB0A
PRE_S
LB0B
50
50
SOA_0+
2
M
U
X
LI_0+
2
Input stage
+EQ
LI_0-
CML
driver
SOA_0-
SOB_0+
2
50
50
1.5V
2
PreL_0
PreL_1
PreS_0
PreS_1
M
U
X
SOB_0-
50
PRE_S
PRE_L
Pre-emphasis
Control
CML
driver
50
VCC
PRE_S
VCC
1.5V
50
50
SIA_1+
50
50
LO_1+
LO_1-
Input stage
+EQ
M
U
X
CML
driver
SIA_1-
SIB_1+
Input stage
+EQ
SIB_1-
PRE_L
1.5V
MUX_S1
50
50
VCC
PORT 1
LB1A
PRE_S
LB1B
50
50
2
LI_1+
2
Input stage
+EQ
LI_1-
SOA_1+
M
U
X
CML
driver
M
U
X
CML
driver
SOA_1-
SOB_1+
2
50
50
1.5V
2
SOB_150
50
PRE_S
VCC pins
2
GND pins
and DAP
Submit Documentation Feedback
VCC
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
DS42MB200
www.ti.com
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
SIB_0+
SIB_0-
GND
40
MUX_S0
VCC
41
VCC
SOA_0-
42
SIA_0-
SOA_0+
43
SIA_0+
LB0A
44
39
38
37
36
PreS0
35
VCC
3
34
LO_0-
SOB_0+
4
33
LO_0+
GND
5
32
GND
LI_0+
6
31
LI_1-
LI_0-
7
30
LI_1+
VCC
8
29
VCC
LO_1+
9
28
SOB_1+
LO_1-
10
27
SOB_1-
GND
11
26
RSV
PreL0
12
25
PreS1
DAP = GND
16
17
18
19
20
21
22
23
24
SOA_1-
SOA_1+
LB1A
LB1B
15
VCC
14
SIB_1+
13
SIB_1-
WQFN-48
Top View Shown
GND
SOB_0-
45
SIA_1+
2
46
SIA_1-
VCC
47
VCC
1
48
MUX_S1
PreL1
LB0B
Connection Diagram
Figure 1. See Package Number NJU0048D
PIN DESCRIPTIONS
Pin Name
Pin Number
I/O
Description
LINE SIDE HIGH SPEED DIFFERENTIAL IO's
LI_0+
LI_0−
6
7
I
Inverting and non-inverting differential inputs of port_0 at the line side. LI_0+ and LI_0− have an
internal 50Ω connected to an internal reference voltage. See Figure 7.
LO_0+
LO_0−
33
34
O
Inverting and non-inverting differential outputs of port_0 at the line side. LO_0+ and LO_0− have an
internal 50Ω connected to VCC.
LI_1+
LI_1−
30
31
I
Inverting and non-inverting differential inputs of port_1 at the line side. LI_1+ and LI_1− have an
internal 50Ω connected to an internal reference voltage. See Figure 7.
LO_1+
LO_1−
9
10
O
Inverting and non-inverting differential outputs of port_1 at the line side. LO_1+ and LO_1− have an
internal 50Ω connected to VCC.
SWITCH SIDE HIGH SPEED DIFFERENTIAL IO's
SOA_0+
SOA_0−
46
45
O
Inverting and non-inverting differential outputs of mux_0 at the switch_A side. SOA_0+ and SOA_0−
have an internal 50Ω connected to VCC.
SOB_0+
SOB_0−
4
3
O
Inverting and non-inverting differential outputs of mux_0 at the switch_B side. SOB_0+ and SOB_0−
have an internal 50Ω connected to VCC.
SIA_0+
SIA_0−
40
39
I
Inverting and non-inverting differential inputs to the mux_0 at the switch_A side. SIA_0+ and SIA_0−
have an internal 50Ω connected to an internal reference voltage. See Figure 7.
SIB_0+
SIB_0−
43
42
I
Inverting and non-inverting differential inputs to the mux_0 at the switch_B side. SIB_0+ and SIB_0−
have an internal 50Ω connected to an internal reference voltage. See Figure 7.
SOA_1+
SOA_1−
22
21
O
Inverting and non-inverting differential outputs of mux_1 at the switch_A side. SOA_1+ and SOA_1−
have an internal 50Ω connected to VCC.
SOB_1+
SOB_1−
28
27
O
Inverting and non-inverting differential outputs of mux_1 at the switch_B side. SOB_1+ and SOB_1−
have an internal 50Ω connected to VCC.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
3
DS42MB200
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
www.ti.com
PIN DESCRIPTIONS (continued)
Pin Number
I/O
SIA_1+
SIA_1−
Pin Name
16
15
I
Inverting and non-inverting differential inputs to the mux_1 at the switch_A side. SIA_1+ and SIA_1−
have an internal 50Ω connected to an internal reference voltage. See Figure 7.
Description
SIB_1+
SIB_1−
19
18
I
Inverting and non-inverting differential inputs to the mux_1 at the switch_B side. SIB_1+ and SIB_1−
have an internal 50Ω connected to an internal reference voltage. See Figure 7.
CONTROL (3.3V LVCMOS)
MUX_S0
37
I
A logic low at MUX_S0 selects mux_0 to switch B. MUX_S0 is internally pulled high. Default state for
mux_0 is switch A.
MUX_S1
13
I
A logic low at MUX_S1 selects mux_1 to switch B. MUX_S1 is internally pulled high. Default state for
mux_1 is switch A.
PREL_0
PREL_1
12
1
I
PREL_0 and PREL_1 select the output pre-emphasis of the line side drivers (LO_0± and LO_1±).
PREL_0 and PREL_1 are internally pulled high. See Table 3 for line side pre-emphasis levels.
PRES_0
PRES_1
36
25
I
PRES_0 and PRES_1 select the output pre-emphasis of the switch side drivers (SOA_0±, SOB_0±,
SOA_1± and SOB_1±). PRES_0 and PRES_1 are internally pulled high. See Table 4 for switch side
pre-emphasis levels.
LB0A
47
I
A logic low at LB0A enables the internal loopback path from SIA_0± to SOA_0±. LB0A is internally
pulled high.
LB0B
48
I
A logic low at LB0B enables the internal loopback path from SIB_0± to SOB_0±. LB0B is internally
pulled high.
LB1A
23
I
A logic low at LB1A enables the internal loopback path from SIA_1± to SOA_1±. LB1A is internally
pulled high.
LB1B
24
I
A logic low at LB1B enables the internal loopback path from SIB_1± to SOB_1±. LB1B is internally
pulled high.
RSV
26
I
Reserve pin to support factory testing. This pin can be left open, or tied to GND, or tied to GND
through an external pull-down resistor.
VCC
2, 8, 14, 20,
29, 35, 38,
44
P
VCC = 3.3V ± 5%.
Each VCC pin should be connected to the VCC plane through a low inductance path, typically with a
via located as close as possible to the landing pad of the VCC pin.
It is recommended to have a 0.01 μF or 0.1 μF, X7R, size-0402 bypass capacitor from each VCC pin
to ground plane.
GND
5, 11, 17, 32,
41
P
Ground reference. Each ground pin should be connected to the ground plane through a low
inductance path, typically with a via located as close as possible to the landing pad of the GND pin.
GND
DAP
P
Die Attach Pad (DAP) is the metal contact at the bottom side, located at the center of the WQFN-48
package. It should be connected to the GND plane with at least 4 via to lower the ground impedance
and improve the thermal performance of the package.
POWER
Functional Description
The DS42MB200 is a signal conditioning 2:1 multiplexer and a 1:2 buffer designed to support port redundancy up
to 4.25 Gbps. Each input stage has a fixed equalizer that provides equalization to compensate about 5 dB of
transmission loss from a short backplane trace (about 10 inches backplane). The output driver has pre-emphasis
(driver-side equalization) to compensate the transmission loss of the backplane that it is driving. The driver
conditions the output signal such that the lower frequency and higher frequency pulses reach approximately the
same amplitude at the end of the backplane, and minimize the deterministic jitter caused by the amplitude
disparity. The DS42MB200 provides 4 steps of user-selectable pre-emphasis ranging from 0, -3, -6 and –9 dB to
handle different lengths of backplane. Figure 1 shows a driver pre-emphasis waveform. The pre-emphasis
duration is 200ps nominal, corresponds to 0.8 bit-width at 4 Gbps. The pre-emphasis levels of switch-side and
line-side can be individually programmed.
The high speed inputs are self-biased to about 1.5V and are designed for AC coupling allowing the DS42MB200
to be directly inserted into the datapath without any limitation. The ideal AC coupling capacitor value is often
based on the lowest frequency component embedded within the serial link. A typical AC coupling capacitor value
ranges between 100 and 1000nF, some specifications with scrambled data may require a larger coupling
capacitor for optimal performance. To reduce unwanted parasitics around and within the AC coupling capacitor, a
body size of 0402 is recommended. Figure 5 shows the AC coupling capacitor placement in an AC test circuit.
The inputs are compatible to most AC coupling differential signals such as LVDS, LVPECL and CML. See
Figure 7 for details.
4
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
DS42MB200
www.ti.com
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
Table 1. LOGIC TABLE FOR MULTIPLEX CONTROLS
MUX_S0
Mux Function
0
MUX_0 select switch_B input, SIB_0±.
1 (default)
MUX_0 select switch_A input, SIA_0±.
MUX_S1
Mux Function
0
MUX_1 select switch_B input, SIB_1±.
1 (default)
MUX_1 select switch_A input, SIA_0±.
Table 2. LOGIC TABLE FOR LOOPBACK Controls
LB0A
Loopback Function
0
Enable loopback from SIA_0± to SOA_0±.
1 (default)
Normal mode. Loopback disabled.
LB0B
Loopback Function
0
Enable loopback from SIB_0± to SOB_0±.
1 (default)
Normal mode. Loopback disabled.
LB1A
Loopback Function
0
Enable loopback from SIA_1± to SOA_1±.
1 (default)
Normal mode. Loopback disabled.
LB1B
Loopback Function
0
Enable loopback from SIB_1± to SOB_1±.
1 (default)
Normal mode. Loopback disabled.
Table 3. LINE-SIDE PRE-EMPHASIS CONTROLS
PreL_[1:0]
Pre-Emphasis Level in mVPP
(VODB)
De-Emphasis Level in
mVPP
(VODPE)
00
1200
1200
0
10 inches
01
1200
850
−3
20 inches
10
1200
600
−6
30 inches
11
(default)
1200
426
−9
40 inches
Pre-Emphasis in dB
(VODPE/VODB)
Typical FR4 board
trace
Table 4. SWITCH-SIDE PRE-EMPHASIS CONTROLS
PreS_[1:0]
Pre-Emphasis Level in mVPP
(VODB)
De-Emphasis Level in
mVPP
(VODPE)
Pre-Emphasis in dB
(VODPE/VODB)
00
1200
1200
0
10 inches
01
1200
850
−3
20 inches
10
1200
600
−6
30 inches
11
(default)
1200
426
−9
40 inches
Typical FR4 board
trace
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
5
DS42MB200
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
1-bit
www.ti.com
1 to N bits
1-bit
1 to N bits
0 dB
-3 dB
-6 dB
VODB
-9 dB
VODPE3
0V
VODPE2
VODPE1
Figure 2. Driver Pre-Emphasis Differential Waveform (showing all 4 pre-emphasis steps)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1) (2)
−0.3V to 4V
Supply Voltage (VCC)
CMOS/TTL Input Voltage
−0.3V to (VCC +0.3V)
CML Input/Output Voltage
−0.3V to (VCC +0.3V)
Junction Temperature
+125°C
Storage Temperature
−65°C to +150°C
Lead Temperature (Soldering, 4 sec.)
+260°C
Thermal Resistance, θJA
33.7°C/W
Thermal Resistance, θJC-top
20.7°C/W
Thermal Resistance, θJC-bottom
5.8°C/W
Thermal Resistance,ΦJB
18.2°C/W
ESD Rating HBM, 1.5 kΩ, 100 pF
6 kV
ESD Rating Machine Model
(1)
(2)
250V
“Absolute Maximum Ratings” are the ratings beyond which the safety of the device cannot be verified. They are not meant to imply that
the device should be operated at these limits.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Recommended Operating Ratings
Supply Voltage (VCC-GND)
Min
Typ
Max
3.135
3.3
3.465
V
20
mVPP
85
°C
100
°C
Supply Noise Amplitude (10 Hz to 2 GHz)
Ambient Temperature
-40
Case Temperature
6
Submit Documentation Feedback
Units
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
DS42MB200
www.ti.com
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ (1)
Max
Units
LVCMOS DC SPECIFICATIONS
VIH
High Level Input
Voltage
2.0
VCC +0.3
V
VIL
Low Level Input
Voltage
−0.3
0.8
V
IIH
High Level Input
Current
−10
10
µA
IIL
Low Level Input Current VIN = GND
124
µA
RPU
Pull-High Resistance
VIN = VCC
75
94
35
kΩ
RECEIVER SPECIFICATIONS
VID
Differential Input
Voltage Range
AC Coupled Differential Signal
Below 1.25 Gbps
At 1.25 Gbps–3.125 Gbps
Above 3.125 Gbps
This parameter is not production tested.
VICM
Common Mode Voltage Measured at receiver inputs reference to ground.
at Receiver Inputs
RITD
Input Differential
Termination
On-chip differential termination between IN+ or
IN−. (2)
100
100
100
1750
1560
1200
mVP-P
mVP-P
mVP-P
1.3
V
84
100
116
Ω
1000
1200
1400
mVP-P
DRIVER SPECIFICATIONS
VODB
VPE
tPE
Output Differential
Voltage Swing without
Pre-Emphasis
RL = 100Ω ±1%
PRES_1=PRES_0=0
PREL_1=PREL_0=0
Driver pre-emphasis disabled.
Running K28.7 pattern at 4.25 Gbps. (3)
See Figure 6 for test circuit.
Output Pre-Emphasis
Voltage Ratio
20*log(VODPE/VODB)
RL = 100Ω ±1%
Running K28.7 pattern at 4.25 Gbps (3)
PREx_[1:0]=00
PREx_[1:0]=01
PREx_[1:0]=10
PREx_[1:0]=11
x=S for switch side pre-emphasis control
x=L for line side pre-emphasis control
See Figure 2 on waveform.
See Figure 6 for test circuit.
Pre-Emphasis Width (4)
Tested at −9 dB pre-emphasis level, PREx[1:0]=11
x=S for switch side pre-emphasis control
x=L for line side pre-emphasis control
See Figure 5 on measurement condition.
125
200
250
ps
42
50
58
Ω
ROTSE
Output Termination
On-chip termination from OUT+ or OUT− to VCC
ROTD
Output Differential
Termination
On-chip differential termination between OUT+ and
OUT−
ΔROTSE
Mis-Match in Output
Termination Resistors
Mis-match in output terminations at OUT+ and
OUT−
VOCM
Output Common Mode
Voltage
(1)
(2)
(3)
(4)
0
−3
−6
−9
dB
dB
dB
dB
Ω
100
2.4
5
%
2.9
V
Typical parameters measured at VCC = 3.3V, TA = 25°C. They are for reference purposes and are not production-tested.
IN+ and IN− are generic names refer to one of the many pairs of complimentary inputs of the DS42MB200. OUT+ and OUT− are
generic names refer to one of the many pairs of the complimentary outputs of the DS42MB200. Differential input voltage VID is defined
as |IN+–IN−|. Differential output voltage VOD is defined as |OUT+–OUT−|.
K28.7 pattern is a 10-bit repeating pattern of K28.7 code group {001111 1000}K28.5 pattern is a 20-bit repeating pattern of +K28.5 and
−K28.5 code groups {110000 0101 001111 1010}
Specified by desigh and characterization using statistical analysis.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
7
DS42MB200
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics (continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ (1)
Max
Units
1
W
POWER DISSIPATION
PD
Power Dissipation
VDD = 3.465V
All outputs terminated by 100Ω ±1%.
PREL_[1:0]=0, PRES_[1:0]=0
Running PRBS 27-1 pattern at 4.25 Gbps
AC CHARACTERISTICS
tR
Differential Low to High
Transition Time
tF
Differential High to Low
Transition Time
tPLH
Differential Low to High
Propagation Delay
tPHL
Differential High to Low
Propagation Delay
tSKP
Pulse Skew (5)
tSKO
Output Skew (6) (5)
tSKPP
Part-to-Part Skew (5)
tSM
Mux Switch Time
RJ
Device Deterministic
Jitter (8) (5)
DRMAX
(5)
(6)
(7)
(8)
8
Maximum Data Rate
Measured at 50% differential voltage from input to
output.
(5)
80
ps
80
ps
0.5
2
ns
0.5
2
ns
|tPHL–tPLH|
20
ps
Difference in propagation delay among data paths in
the same device.
200
ps
Difference in propagation delay between the same
output from devices operating under identical
condition.
500
ps
6
ns
See Figure 6 for test circuit.
Alternating-1-0 pattern.
Pre-emphasis disabled.
At 1.25 Gbps
At 4.25 Gbps
2
2
psrms
psrms
See Figure 6 for test circuit.
Pre-emphasis disabled.
At 4.25 Gbps, PRBS7 pattern for DS42MB200@ –
40° to 85°C
35
pspp
Measured from VIH or VIL of the mux-control or
loopback control to 50% of the valid differential
output.
Device Random
Jitter (7) (5)
DJ
Measured with a clock-like pattern at 100 MHz,
between 20% and 80% of the differential output
voltage. Pre-emphasis disabled.
Transition time is measured with fixture as shown in
Figure 6, adjusted to reflect the transition time at the
output pins.
Tested with alternating-1-0 pattern
1.8
4.25
Gbps
Specified by desigh and characterization using statistical analysis.
tSKO is the magnitude difference in the propagation delays among data paths between switch A and switch B of the same port and
similar data paths between port 0 and port 1. An example is the output skew among data paths from SIA_0± to LO_0±, SIB_0± to
LO_0±, SIA_1± to LO_1± and SIB_1± to LO_1±. Another example is the output skew among data paths from LI_0± to SOA_0±, LI_0± to
SOB_0±, LI_1± to SOA_1± and LI_1± to SOB_1±. tSKO also refers to the delay skew of the loopback paths of the same port and
between similar data paths between port 0 and port 1. An example is the output skew among data paths SIA_0± to SOA_0±, SIB_0± to
SOB_0±, SIA_1± to SOA_1± and SIB_1± to SOB_1±.
Device output random jitter is a measurement of the random jitter contribution from the device. It is derived by the equation sqrt(RJOUT2–
RJIN2), where RJOUT is the random jitter measured at the output of the device in psrms, RJIN is the random jitter of the pattern generator
driving the device.
Device output deterministic jitter is a measurement of the deterministic jitter contribution from the device. It is derived by the equation
(DJOUT–DJIN), where DJOUT is the peak-to-peak deterministic jitter measured at the output of the device in pspp, DJIN is the peak-topeak deterministic jitter of the pattern generator driving the device.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
DS42MB200
www.ti.com
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
Timing Diagrams
80%
80%
VODB
0V
20%
20%
tR
tF
Figure 3. Driver Output Transition Time
50% VID
IN
tPLH
tPHL
50% VOD
OUT
Figure 4. Propagation Delay from input to output
1-bit
1 to N bits
1-bit
1 to N bits
tPE
20%
-9 dB
80%
0V
VODPE3
Figure 5. Test condition for output pre-emphasis duration
DS42MB200 Test Fixture
Pattern
Generator
DC
Block
VCC
DS42MB200
INPUT
25-inch
TLine
D-
IN+
IN-
EQ
R
M
U
X
50+-1%
OUT+
< 2"
D
OUT-
Coax
1000 mVpp
Differential
Oscilloscope or
Jitter Measurement
Instrument
Coax
Coax
D+
DC
Block
50: TL
Coax
GND
50: TL
50 +-1%
Figure 6. AC Test Circuit
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
9
DS42MB200
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
www.ti.com
VCC
5k
IN +
50
1.5V
EQ
50
IN 3.9k
180 pF
Figure 7. Receiver Input Termination and Biasing Circuit
APPLICATIONS INFORMATION
The DS42MB200 input equalizer provides equalization to compensate about 5 dB of transmission loss from a
short backplane transmission line. For characterization purposes, a 25-inch FR4 coupled micro-strip board trace
is used in place of the short backplane link. The 25-inch microstrip board trace has approximately 5 dB of
attenuation between 375 MHz and 1.875 GHz, representing closely the transmission loss of the short backplane
transmission line. The 25-inch microstrip is connected between the pattern generator and the differential inputs of
the DS42MB200 for AC measurements.
Trace Length
Finished Trace
Width W
Separation between
Traces
Dielectric Height H
Dielectric Constant
εR
Loss Tangent
25 inches
8.5 mil
11.5 mil
6 mil
3.8
0.022
Data eye after 25-inch FR4 trace
Data eye after DS42MB200
200 mV/DIV
200 mV/DIV
200 mV/DIV
Data eye from pattern generator
50 ps/DIV
50 ps/DIV
Pattern
Generator, 4 Gb/s
50 ps/DIV
DS42MB200
PE=0dB
D+
D-
25-inch FR4
board trace
IN+
IN-
M
EQ
R
U
OUT+
D
X
40-inch
FR4 trace
OUT-
200 mV/DIV
27 -1 pattern
50 ps/DIV
Figure 8. Data input and output eye patterns with driver set to 0 dB pre-emphasis
10
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
DS42MB200
www.ti.com
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
Data eye after DS42MB200
200 mV/DIV
200 mV/DIV
Data eye after 25-inch FR4 trace
200 mV/DIV
Data eye from pattern generator
50 ps/DIV
50 ps/DIV
Pattern
Generator, 4 Gb/s
50 ps/DIV
DS42MB200
PE = 9 dB
D+
D-
25-inch FR4
board trace
M
IN+
IN-
EQ
R
OUT+
U
D
40-inch
FR4 trace
OUT-
X
200 mV/DIV
27 -1 pattern
50 ps/DIV
Figure 9. Data input and output eye patterns with driver set to 9dB pre-emphasis
Passive Backplane
Line Cards
DS42MB200
HT
TD
ASIC
PHY
SOA
LI
SerDes
SOB
T_ CLK
SIA
RD
R_CLK
HR
LO
SIB
REFCLK
Mux/Buf
Clock
Distribution
ASIC or FPGA with integrated SerDes
PC
Switch Card 2
Switch Card 1
SerDes
TD
Switch
ASIC
HT
T_ CLK
RD
R_CLK
HR
REFCLK
Clock
Distribution
ASIC or FPGA with integrated SerDes
Figure 10. Application diagram (showing data paths of port 0)
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
11
DS42MB200
SNOSAT8G – JANUARY 2006 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision F (April 2013) to Revision G
•
12
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 11
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS42MB200
PACKAGE OPTION ADDENDUM
www.ti.com
18-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DS42MB200TSQ
ACTIVE
WQFN
NJU
48
250
TBD
Call TI
Call TI
-40 to 85
DS42MB200TSQ/NOPB
ACTIVE
WQFN
NJU
48
250
Green (RoHS
& no Sb/Br)
SN
Level-3-260C-168 HR
-40 to 85
42MB200
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DS42MB200TSQ/NOPB
Package Package Pins
Type Drawing
WQFN
NJU
48
SPQ
250
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
178.0
16.4
Pack Materials-Page 1
7.3
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
7.3
1.3
12.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS42MB200TSQ/NOPB
WQFN
NJU
48
250
213.0
191.0
55.0
Pack Materials-Page 2
MECHANICAL DATA
NJU0048D
SQA48D (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated