H SERIES HIGH Q CAPACITOR SPECIFICATION Rev. B FEATURES: - High Q and low ESR - Extend working range for wireless products - Extend battery life of portable devices PART NUMBER DESCRIPTION H 0402 Series Size 0402 (1005) H : High Q, Low 0603 (1608) ESR 0805 (2012) 250 Rated Voltage (VDC) 6R3=6.3 100-10 160=16 250=25 500=50 101=100 201=200 251=250 501=500 631=630 N Dielectric N: NP0 0R1 Capacitance 0R1=0.10pF 0R5=0.5pF 1R0=1.0pF 100=10pF 101=100pF B Tolerance A: ±0.05pF B: ±0.1pF C: ±0.25pF D: ±0.5pF F: ±1% G: ±2% J: ±5% T C Termination C=Cu/Ni/Sn Packaging T=7” Paper Tape U=13” Paper Tape E=7” Plastic Tape Q=13” Plastic Tape Z or blank=Bulk General Electrical Data Dielectric Size Capacitance Range Capacitance tolerance Rated voltage (WVDC) NP0 0402, 0603, 0805 0402: 0.5pF to 470pF(<0.5pF: on requested) 0603: 0.5pF to 3300pF 0805: 0.5pF to 390pF Cap≤5pF: A (±0.05pF ), B (±0.1pF), C (±0.25pF) 5pF<Cap<10pF: B (±0.1pF), C (±0.25pF), D (±0.5pF) Cap≥10pF: F (±1%), G (±2%), J (±5%) 16V, 25V, 50V, 100V, 200V, 250V, 500V, 630V Insulation resistance (25°C) Operating temperature Cap≥30pF, Q≥1000 Cap<30pF,Q≥400+20C ≥10GΩ -55°C to +125°C Temperature coefficient of capacitance Termination ±30ppm/°C Ni/Sn (lead-free termination) Q Frontier Electronics Corp.® http://www.frontierusa.com Page 1 of 8 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Rev. B External Dimensions Case Size EIA (mm) Outline 0402 (1005) 0603 (1608) L (mm) W (mm) 1.00±0.05 0.50±0.05 1.00±0.20 0.50±0.20 0.5±0.20 1.60±0.10 0.80±0.10 0.80±0.07 1.60+0.15/-0.10 0.80+0.15/-0.10 1.60±0.20 0.80±0.20 2.00±0.15 1.25±0.10 0805 (2012) 2.00±0.20 1.25±0.20 T (mm) Soldering Method MB (mm) R 0.25 +0.05/-0.1 R/W 0.40±0.15 0.50±0.05 0.50+0.02/-0.05 0.50±0.10 0.80+0.15/-0.10 0.8±0.20 0.50±0.10 R/W 0.60±0.10 R/W 0.80±0.10 R/W 1.25±0.10 R 0.85±0.10 R/W 1.25±0.20 R 0.50±0.20 Thickness Codes/Packaging Quantity Case Size Size Code Max Thickness 0402 0402 BA BC 0.55 0.7 1.0 ± 0.05 1.0 ± 0.2 0.5 ± 0.05 0.5 ± 0.2 0603 0603 0603 CA CC CD 0.87 0.95 1 1.6 ± 0.1 1.6 +0.15/-0.01 1.6 ± 0.2 0805 0805 0805 0805 0805 DB DC DD DE DF 0.7 0.9 1.35 0.95 1.45 2.0 ± 0.15 2.0 ± 0.15 2.0 ± 0.15 2.0 ± 0.2 2.0 ± 0.2 Length Frontier Electronics Corp.® http://www.frontierusa.com Width Thickness Paper Tape 7" Reel 13" Reel 0.5 ± 0.05 0.5 ± 0.2 10,000 10,000 50,000 - 0.8 ± 0.1 0.8 +0.15/-0.1 0.8 ± 0.2 0.8 ± 0.07 0.8 ± +0.15/-0.1 0.8 ± 0.2 4,000 4,000 4,000 15,000 15,000 15,000 1.25 ± 0.1 1.25 ± 0.1 1.25 ± 0.1 1.25 ± 0.2 1.25 ± 0.2 0.6 ± 0.1 0.8 ± 0.1 1.25 ± 0.1 0.85 ± 0.1 1.25 ± 0.2 4,000 4,000 15,000 15,000 4,000 15,000 Page 2 of 8 Embossed Plastic Tape 7" Reel 13" Reel 3,000 10,000 3,000 10,000 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Frontier Electronics Corp.® http://www.frontierusa.com Page 3 of 8 Rev. B 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Impedance vs. Frequency (Typical) Rev. B SRF vs. Capacitance (Typical) ESR vs. Frequency (Typical) Frontier Electronics Corp.® http://www.frontierusa.com Page 4 of 8 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Item 1 Visual and Mechanical 2 Capacitance Test Condition --- Requirements * No remarkable defect * Dimensions conform to individual specification sheet * Shall not exceed the limits given in the detailed spec NP0: Cap≥30pF, Q≥1000, Cap<30pF,Q≥400+20C X7R, X5R: Rated voltage (DCV) ≤ 2.5% 35V ≤3.5% Class I: NP0Class I: NP0 Cap≤1,000pF 1.0±0.2Vrms, 1MHz±10% Cap>1,000pF 1.0±0.2Vrms, 1KHz±10% 16V Q/ DF (Dissipation Factor) D.F. ≤ ≥ 50V 25V 3 Exception of D.F. ≤ ≤3.5% 10V ≤3% 0201(50V), 0603 ≥ 0.047μF, 0805 ≥ 0.18μF, 1206 ≥ 0.47μF ≤5% 1210 ≥ 4.7μF ≤10% 0603≥1μF, 0805≥1μF,1206≥2.2μF, 1210≥10μF ≤10% 0805≥2.2µF, 1210≥10μF ≤5% 0201≥0.01μF,0805≥1μF, 1210≥10μF ≤7% 0603≥0.33μF, 1206≥4.7μF ≤10% 0402≥0.10μF,0603≥0.47μF, 0805≥2.2μF, ≤5% 0201≥0.01μF,0402≥0.033μF, 0603≥0.15μF, 0805≥0.68μF, 1206≥2.2μF,1210≥4.7μF ≤10% 0402≥ 0.22uF, 0603≥0.68μF,0805≥2.2μF, 1206≥4.7μF, 1210≥22μF ≤3.5% Class II: X7R, X5R,Y5V Cap≤10µF, 1.0±0.2Vrms, 1kHz±10% ** Cap>10µF, 0.5±0.2Vrms, 120Hz±20% ** Test condition: 0.5±0.2Vrms ，1KHz±10% X7R: 0603≥225 (10V), 0805=106 (6.3V&10V) X5R: 0201≥224 (6.3V), 0402≥475 (6.3V), 0402≥225(10V),0603=106 (6.3V) Rev. B ≤10% ≤5% ≤15% 6.3V ≤10% 4V ≤15% 0201≥0.012μF,0402≥0.33μF,0603≥0.33μF,0805 ≥2.2μF, 1206≥2.2μF,1210≥22μF 0201≥0.1μF, 0402≥1μF ≤15% 0201≥0.1μF,0402≥1μF,0603≥10μF, 0805≥4.7μF, 1206≥47μF :1210≥100μF ≤20% --- 0402≥2.2μF --- Y5V: D.F. ≤ Rated voltage Exception of D.F.≤ ≥50V ≤5% ≤7% 35V ≤7% --- 25V ≤5% 0603≥0.1μF, 0805≥0.47μF, 1206≥4.7μF, Cap≥1μF --- ≤7% 0402≥0.047μF,0603≥0.1μF, 0805≥0.33μF,1206≥1μF, 1210≥4.7μF ≤9% 0402≥0.068μF,0603≥0.47μF, 1206≥4.7μF, 1210≥22μF, Cap≥1μF 16V (C<1.0μF) ≤7% ≤9% ≤12.5% 0402≥0.068μF, 0603≥0.68μF 0402≥0.22μF 16V (C≥1.0μF) ≤9% ≤12.5% 0603≥2.2μF, 0805≥3.3μF,1206≥10μF, 1210≥22μF, 1812≥47μF, Cap≥1μF 10V 6.3V ≤12.5% ≤20% ≤20% --- 0402≥0.47μF --- *To apply voltage(≤100V) 250%. *Duration: 1 to 5 sec. *Charge & discharge current less than 50mA. 4 Dielectric Strength *To apply voltage: 200V ~300V & LD series ≥2 times V DC 500V ~ 999V ≥1.5 times V DC 1000V ~ 3000V ≥1.2 times V DC *Cut-off, set at 10mA *TEST= 15 sec. *RAMP=0 *No evidence of damage or flash over during test. 10GΩ or RxC≥500Ω-F whichever is lower. Class II (X7R, X7E, X5R, Y5V): To apply rated voltage for max. 120 sec. 5 Insulation Resistance Rated Voltage: 200V ~ 630V >630V 6 7 Temperature Coefficient Adhesive Strength of Termination http://www.frontierusa.com Insulation Resistance 10GΩ or RxC≥100 Ω-F whichever is lower. To apply rated voltage (500V max.) for >10GΩ or 100Ω-F whichever is lower. 60 sec. To apply 500V for 60sec. >10GΩ With no electrical load. T.C. Operating Temp NPO (C0G) NPO (C0H) -55~125°C at 25°C NPO (C0J) X7R X5R -55~ 85°C at 25°C Y5V -25~ 85°C at 20°C *Pressurizing force： 0201: 2N 0402 & 0603: 5N >0603: 10N *Test time：10 ±1 sec Frontier Electronics Corp.® Rated voltage 100V: X7R 50V:0603≥1µF,0805≥1µF, 1206≥2.2μF, 1210≥4.7µF 35V:0805≥2.2µF,1210≥10μF 25V:0402≥1µF,0603≥2.2µF,0805≥2.2µF, 1206≥10µF,1210≥10µF 16V:0402≥0.22µF,0603≥1µF,0805≥2.2µF, 1206≥10µF,1210≥47µF 10V:0201≥47nF,0402≥0.47µF,0603≥0.47µF, 0805≥2.2µF, T.C. NPO (C0G) NPO (C0H) NPO (C0J) X7R X5R Y5V Capacitance Change Within ±30ppm/°C Within ±60ppm/°C Within ±120ppm/°C Within ±15% Within ±15% Within +30%/-80% * No remarkable damage or removal of the terminations. Page 5 of 8 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Item 8 Vibration Resistance 9 Solderability 10 11 Test Condition * Vibration frequency: 10~55 Hz/min. * Total amplitude: 1.5mm * Test time: 6 hours (Two hrs each in three mutually perpendicular directions) * Measurement to be made after keeping at room temp. for 24±2 hours * Solder temperature: 235±5°C * Dipping time: 2±0.5 sec. Bending Test *The middle part of substrate shall be pressurized by means of the pressurizing rod at a rate of approximately 1 mm per second until the deflection becomes 1 mm and then the pressure shall be maintained for 5±1 sec. *Measurement to be made after keeping at room temp. for 24±2 hrs. Resistance to Soldering Heat * Solder temperature: 260±5°C * Dipping time: 10±1 sec * Preheating: 120 to 150°C for 1 minute before immersing the capacitor in an eutectic solder. * Before initial measurement (Class II only): Perform 150+0/-10°C for 1 hr and then set for 24±2 hrs at room temp. * Measurement to be made after keeping at room temp. for 24±2 hrs. * Conduct the five cycles according to the temperatures and time. Step 1 2 12 3 Temperature Cycle 4 Temp. (°C) Min. operating temp. +0/-3 Room temp. Max. operating temp. +3/-0 Room temp. Time (min.) 30±3 2~3 Rev. B Requirements * No remarkable damage. * Cap change and Q/D.F.: To meet initial spec. 95% min. coverage of all metalized area. * No remarkable damage. * Capacitance change： NP0: within ±5% or 0.5pF whichever is larger X7R, X7E, X5R: within ±12.5% Y5V: within ±30% (This capacitance change means the change of capacitance under specified flexure of substrate from the capacitance measured before the test.) * No remarkable damage. * Capacitance change: NP0: within ±2.5% or 0.25pF whichever is larger X7R, X7E, X5R: within ±7.5% Y5V: within ±20% * Q/D.F., I.R. and dielectric strength: To meet initial requirements. * 25% max. leaching on each edge. * No remarkable damage. * Capacitance change NP0: within ±2.5% or 0.25pF whichever is larger X7R, X7E, X5R: within ±7.5% Y5V: within ±20% * Q/D.F., I.R. and dielectric strength: To meet initial requirements. 30±3 2~3 * Before initial measurement (Class II only): Perform 150+0/-10°C for 1 hr and then set for 24±2 hrs at room temp. * Measurement to be made after keeping at room temp. for 24±2 hrs. * No remarkable damage. * Cap change: NP0: within ±5% or 0.5pF whichever is larger X7R, X7E, X5R: ≥10V**,within ±12.5%;6.3V within ±25%;TT series,within ±25% **10V:0603≥4.7μF;0402≥1μF;0201≥0.1μF, within ±25%; Y5V: ≥10V, within ±30%; 6.3V, within +30/-40% * Q/D.F. value: NP0: More than 30pF Q≥350, 10pF≤C≤30pF, Q≥275+2.5C,Less than 10pF Q≥200+10C X7R, X5R: Rated vol. ≤3% 35V ≤5% 25V ≤5% 16V 13 Humidity (Damp Heat) Steady State * Test temp.: 40±2°C * Humidity: 90~95% RH * Test time: 500+24/-0hrs. * Before initial measurement (Class II only): Perform 150 +0/-10°C for 1 hr and then set for 24±2 hrs. at room temp. * Measurement to be made after keeping at room temp. for 24±2 hrs. D.F.≤ ≥50V ≤5％ ≤6% ≤10% ≤20% ≤20% ≤10% ≤14% Exception of D.F.≤ 0201(50V); 0603≥0.047μF; 0805≥0.18μF; 1206≥0.47μF 1210≥4.7μF 0603≥1μF; 0805≥1μF; 1206≥2.2μF; 1210≥10μF 0805≥2.2µF;1210≥10μF 0201≥0.01μF;0805≥1μF; 1210≥10μF 0603≥0.33μF;1206≥4.7μF ≤15% 6≥6.8μF1210≥22μF ≤10% 0603≥0.15μF;0805≥0.68μF;1206≥2.2μF;1210≥4.7μF ≤15% 0201≥0.01μF;0402≥0.033μF;0603≥0.68μF;0805≥2.2μF; 1206≥4.7μF; 1210≥22μF ≤ ≤15% ≤20% 6.3V ≤15% ≤30% 4V X7R/X7E, LD≤20% series : DF--- 3% 10V ≤7.5% Y5V: Rated vol. D.F.≤ ≥50V ≤7.5% 35V ≤10% ≤10% --≤10% 25V ≤7.5% 16V (C<1.0μF) 16V (C≥1.0μF) 10V 6.3V ≤10% ≤12.5% ≤20% ≤12.5% ≤20% ≤20% ≤30% ≤30% --- ≤15% 0201≥0.012μF; 0402≥0.33μF; 0603≥0.33μF;0805≥2.2μF; 1206≥2.2μF; 0201≥0.1μF ;0402≥1μF 0201≥0.1μF;0402≥1μF;0603≥10μF; 0805≥4.7μF; --- Exception of D.F.≤ 0603≥0.1μF; 0805≥0.47μF; 1206≥4.7μF; Cap≥1μF --0402≥0.047μF;0603≥0.1μF;0805≥0.33μF; 1206≥1μF; 1210≥4.7μF 0402≥0.068μF;0603≥0.47μF;1206≥4.7μF; 1210≥22μF; Cap≥1μF 0402≥0.068μF; 0603≥0.68μF 0402≥0.22μF 0603≥2.2μF;0805≥3.3μF;1206≥10μF;1210≥22μF; 1812≥47μF; Cap≥1μF 0402≥0.47μF --- *I.R.: ≥10V, 1GΩ or 50 Ω-F whichever is lower. Class II (X7R, X7E, X5R, Y5V) Rated voltage Insulation Resistance 100V: X7R 50V:0603≥1µF;0805≥1µF; 206≥2.2μF;1210≥4.7µF 25V:0402≥1µF;0603≥2.2µF;0805≥2.2µF;1206≥10µF;1210≥10µF 1GΩ or RxC≥10 Ω-F whichever is lower. 16V:0402≥0.22µF;0603≥1µF;0805≥2.2µF;1206≥10µF;1210≥47µF 10V:0201≥47nF;0402≥0.47µF;0603≥0.47µF;0805≥2.2µF;1206≥4. 7µF;1210≥47µF Frontier Electronics Corp.® http://www.frontierusa.com Page 6 of 8 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Item Test Condition Rev. B Requirements * No remarkable damage. Cap change: NP0: ±7.5% or 0.75pF whichever is larger. X7R, X7E, X5R: ≥10V**,within ±12.5%;6.3V within ±25%; **10V:0603≥4.7μF;0402≥1μF;0201≥0.1μF, within ±25%; Y5V: ≥10V, within ±30%; 6.3V, within +30/-40% Q/D.F. value: NP0: C≥30pF,Q≥200;C<30pF, Q≥100+10/3C X7R, X5R: Rated voltage ≥50V ≤3% ≤5% 35V 14 Humidity (Damp Heat) Load * Test temp.: 40±2°C * Humidity: 90~95%RH * Test time: 500+24/-0 hrs. * Voltage： Rated voltage.(Max.500V) * Before initial measurement (Class II only): To apply test voltage for 1hr at 40°C and then set for 24±2 hrs at room temp.* Measurement to be made after keeping at room temp. for 24±2 hrs. Exception of D.F. ≤ D.F.≤ ≤6% 0201(50V);0603≥0.047μF; 0805≥0.18μF; 1206≥0.47μF ≤10% 1210≥4.7μF ≤20% 0603≥1μF; 0805≥1μF; 1206≥2.2μF; 1210≥10μF ≤20% 0805≥2.2µF;1210≥10μF ≤10% 0201≥0.01μF;0805≥1μF; 1210≥10μF ≤14% ≤15% 0603≥0.33μF;1206≥4.7μF ≤10% 0603≥0.15μF;0805≥0.68μF;1206≥2.2μF;1210≥4.7μF ≤15% 0201≥0.01μF;0402≥0.033μF;0603≥0.68μF;0805≥2.2μF; 1206≥4.7μF; 1210≥22μF ≤15% 0201≥0.012μF;0402≥0.33μF; 0603≥0.33μF;0805≥2.2μF; 1206≥2.2μF; 1210≥22μF ≤20% 0201≥0.1μF ;0402≥1μF 25V ≤5% 16V ≤5％ 10V ≤7.5% 6.3V ≤15% ≤30% 0201≥0.1μF;0402≥1μF;0603≥10μF; 0805≥4.7μF;1206≥47μF;1210≥100μF 4V ≤20% --- --- 0402≥0.10μF;0603≥0.47μF;0805≥2.2μF; 1206≥6.8μF;1210≥22μF X7R/X7E, LD series : DF≤3% Y5V: Rated voltage ≥50V 35V D.F.≤ ≤7.5% ≤10% 25V ≤7.5% 16V (C<1.0μF) ≤10% 16V (C≥1.0μF) 10V ≤12.5% ≤20% ≤30% 6.3V ≤10% --- Exception of D.F.≤ 0603≥0.1μF; 0805≥0.47μF;1206≥4.7μF; Cap≥1μF --- ≤10% ≤15% ≤12.5% 0402≥0.047μF;0603≥0.1μF;0805≥0.33μF;1206≥1μF; 1210≥4.7μF 0402≥0.068μF;0603≥0.47μF;1206≥4.7μF;1210≥22μF; Cap≥1μF 0402≥0.068μF; 0603≥0.68μF ≤20% ≤20% ≤30% 0402≥0.22μF 0603≥2.2μF;0805≥3.3μF;1206≥10μF;1210≥22μF;1812≥47μF; Cap≥1μF 0402≥0.47μF --- --- *I.R.: ≥10V, 500MΩ or 25 Ω-F whichever is lower. Class II (X7R, X7E, X5R, Y5V) Rated voltage Insulation Resistance 100V: X7R 50V:0603≥1µF;0805≥1µF; 1206≥2.2μF;1210≥4.7µF 25V:0402≥1µF;0603≥2.2µF;0805≥2.2µF;1206≥10µF;1210≥10µF 16V:0402≥0.22µF;0603≥1µF;0805≥2.2µF;1206≥10µF;1210≥47µF 10V:0201≥47nF;0402≥0.47µF;0603≥0.47µF;0805≥2.2µF; 1206≥4.7µF;1210≥47µF *Test temp.： NP0, X7R/X7E: 125±3°C X5R, Y5V: 85±3°C *Test time: 1000+24/-0 hrs. *To apply voltage: (1) 6.3V or C≥10µF 150% of rated voltage: (2) 10V≤Ur<500V: 200% of rated voltage. (3) 500V: 150% of rated voltage. (4) Ur≥630V: 120% of rated voltage.(5) 100% of rated voltage for below range: Size Dielectric Rated voltage 0201 0402 0603 0805 X5R/X7R X5R/X7R X5R/X7R X5R/X7R X5R/X7R NP0 6.3V,10V 6.3V,10V 6.3V,10V 6.3V 6.3V 3000V 1206 Size 0402 15 High Temperature Load (Endurance) 0603 0805 Dielectric X5R/X7R Y5V X5R/X7R Y5V X5R/X7R Y5V Rated voltage 10V,16V,25V 16V 10V,16V 16V 10V 16V Capacitance C≥0.22μF C≥0.47μF C≥1.0μF C≥2.2μF C≥4.7μF C≥4.7μF *Before initial measurement (Class II only): To apply test voltage for 1hr at test temp. and then set for 24±2 hrs at room temp. *Measurement to be made after keeping at room temp. for 24±2 hrs. * No remarkable damage. Cap change: NP0: ±3.0% or ±0.3pF whichever is larger X7R, X7E, X5R: ≥10V**,within ±12.5%;6.3V within ±25%; **10V:0603≥4.7μF;0402≥1μF;0201≥0.1μF, within ±25%; Y5V: ≥10V, within ±30%; 6.3V, within +30/-40% Q/D.F. value: NP0: More than 30pF, Q≥350; 10pF≤C<30pF, Q≥275+2.5C; Less than 10pF, Q≥200+10C X7R, X5R: Rated voltage (6)150% of rated voltage for below range: 500MΩ or RxC≥5 Ω-F whichever is lower. D.F.≤ ≥50V ≤3% 35V ≤5% 25V ≤5% 16V ≤5％ 10V ≤7.5% 6.3V 4V X7R: DF≤3% Y5V: ≤15% ≤20% Rated voltage D.F.≤ ≥50V ≤7.5% 25V ≤7.5% 16V (C<1.0μF) ≤10% 16V (C≥1.0μF) ≤12.5% 10V ≤20% Exception of D.F.≤ ≤6% ≤10% ≤20% ≤20% ≤10% ≤14% ≤15% ≤10% ≤15% ≤15% ≤20% ≤30% -- 0201(50V);0603≥0.047μF; 0805≥0.18μF; 1206≥0.47μF 1210≥4.7μF 0603≥1μF; 0805≥1μF; 1206≥2.2μF; 1210≥10μF 0805≥2.2µF;1210≥10μF 0201≥0.01μF;0805≥1μF; 1210≥10μF 0603≥0.33μF;1206≥4.7μF 0402≥0.10μF;0603≥0.47μF;0805≥2.2μF; 1206≥6.8μF;1210≥22μF 0603≥0.15μF;0805≥0.68μF; 1206≥2.2μF;1210≥4.7μF 0201≥0.01μF;0402≥0.033μF; 0603≥0.68μF;0805≥2.2μF; 1206≥4.7μF; 1210≥22μF 0201≥0.012μF;0402≥0.33μF; 0603≥0.33μF;0805≥2.2μF; 1206≥2.2μF; 1210≥22μF 0201≥0.1μF ;0402≥1μF 0201≥0.1μF;0402≥1μF; 0603≥10μF;0805≥4.7μF; 1206≥47μF; 1210≥100μF -- ≤10% 0603≥0.1μF; 0805≥0.47μF;1206≥4.7μF;Cap≥1μF ≤10% ≤15% ≤12.5% 0402≥0.047μF;0603≥0.1μF; 0805≥0.33μF;1206≥1μF; 1210≥4.7μF ≤20% ≤20% ≤30% 0402≥0.22μF 0603≥2.2μF;0805≥3.3μF;1206≥10μF; 1210≥22μF;1812≥47μF;Cap≥1μF 0402≥0.47μF Exception of D.F.≤ 0402≥0.068μF;0603≥0.47μF; 1206≥4.7μF;1210≥22μF;Cap≥1μF 0402≥0.068μF; 0603≥0.68μF --6.3V ≤30% --*I.R.: ≥10V, 1GΩ or 50 Ω-F whichever is lower. Class II (X7R, X7E, X5R, Y5V): Rated voltage 100V: X7R 50V:0603≥1µF;0805≥1µF; 1206≥2.2μF;1210≥4.7µF 25V:0402≥1µF;0603≥2.2µF; 0805≥2.2µF;1206≥10µF;1210≥10µF 16V:0402≥0.22µF;0603≥1µF; 0805≥2.2µF;1206≥10µF;1210≥47µF 10V:0201≥47nF;0402≥0.47µF; 0603≥0.47µF;0805≥2.2µF; 1206≥4.7µF;1210≥47µF 6.3V ; 4V Frontier Electronics Corp.® http://www.frontierusa.com Page 7 of 8 Insulation Resistance 1GΩ or RxC≥10 Ω-F whichever is lower. 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 H SERIES HIGH Q CAPACITOR SPECIFICATION Name 1 Ceramic material 2 Inner electrode 3 4 Termination 5 NP0/X7R Rev. B NPO/X7R/X5R/Y5V BaTiO3 based Ni Inner layer Cu Middle layer Ni Outer layer Sn Storage and handling (1) (2) Products should be stored at 5 to 40C ambient temperature and 20 to 70%. relative humidity. It is recommended that the product be used within one year from shipment. After one year from shipment, solderability should be checked. Cautions a. b. c. Corrosive gas reacts with the terminal electrodes of capacitors. Do not store capacitors in the proximity of corrosive gas (e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas etc.) otherwise there can be solderability issues. In a corrosive atmosphere, solderability might be degraded, and/or silver migration may occur which can cause lower reliability. Dewing caused by rapid humidity changes and/or photochemical changes of the terminal electrode (caused by direct sunlight contact) can affect the solderability and electrical performance. Do not store capacitors under direct sunlight or in dewing conditions. Recommended reflow profile for SnAgCu solder paste: 4℃/ sec max Recommended wave profile for SnAgCu solder paste: Over 60sec at least by natural cooling Frontier Electronics Corp.® http://www.frontierusa.com Page 8 of 8 667 E. Cochran St. Simi valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989