Optiva OTS-2OP Series EDFA Micro Erbium Doped Fiber pre-Amplifier DATASHEET | FEBRUARY 2014 SATCOM The Optiva OTS-2OP Series of Micro Erbium Doped Fiber pre-Amplifier (µEDFA) Gain Block Modules are an ideal building block for system integrators to extend the fiber link for long-haul signal transport. The OTS-2OP Series is designed to meet the most demanding noise performance requirements of fiber optic communications and control systems and performs all the functions required of an optical pre-amplifier for system integration. The OTS-2OP Series μEDFA pre-amplifier modules provide output optical isolation for stable, low noise operation. The output optical signal power levels are detected for monitoring and control. The very low level input optical signal is initially pre-amplified, then amplified with active output power control for constant power mode operation. Applications CATV Systems The OTS-2OP Series also provide local and remote monitors and alarms for all critical operating parameters via SNMP and EMCORE View GUI. The optical output can be split into multiple ports by optional external splitter. Long Distance RF/Microwave Fiber Optic Communication Links System Applications Sensing and Control Systems High-Performance Supertrunking Links High Power Distribution Networks Redundant Ring Architectures FTTx Networks Features Full Function Fiber Optic pre-Amplifier Low Noise Figure (NF typ < 3.3 dB) Pin: > -45 dBm The OTS-2OP Series μEDFA modules fit in the EMCORE Optiva family of enclosures including the 3 RU 19" rack-mount, fan-cooled enclosure (Model OT-CC-16F) supporting up to 16 Optiva modules and the 1 RU 19" rack-mount, fan-cooled enclosure (Model OT-CC-6) supporting up to 6 Optiva modules. In addition, the OTS-2OP Series modules fit the compact tabletop or wall-mountable enclosure Model OT-DTCR-2. The EMCORE Optiva family of platforms consists of a wide range of RF, microwave, video, data and audio signal transport solutions. The integration of the OTS-2OP Series pre-Amplified μEDFA Gain Block Modules and the Optiva family of 1550 nm optical MUX-DEMUX solutions into the platform can extend the fiber links of long-haul signal transport for a wide range of applications. Block Diagram Pout (saturated): ≈ +14 dBm Small Signal Gain > 37 dB Low Electrical Power Consumption Output Isolation > 40 dB Polarization Dependent Gain < 0.1 dB Polarization Mode Dispersion < 0.2 ps Output Return Losses < -40 dB Output Residual Pump Power < -40 dBm Fits in Optiva Enclosures (16, 6, and 2 slot) All Optiva Communication Features RoHS Compliant © 2014 EMCORE Corporation | REV 2014.02 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2OP Series EDFA Micro Erbium Doped Fiber pre-Amplifier DATASHEET | FEBRUARY 2014 SATCOM Optical/Electrical Characteristics Parameter Unit Limit Model Comments (Note 1) 1400 Operating Input Power Pin (dBm) Max 0 Operating Input Power Pin (dBm) Min -45 Saturated Output Power Pout (dBm) Nominal 14 +/-.25 (Notes 2, 3) NF (dB) Max 3.3 dB (Note 4) (dB) Max +/- 0.1 (Note 5) Psys (W) Max 4 70°C Case Noise Figure Output Power Stability Power Consumption (Steady state) NOTES: 1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges 2. Measurement variations 3. Measured @ 1550 nm and Pin = -4 dBm 4. Measured @ 1550 nm and Pin = -30 dBm 5. Over polarization and temperature General and Mechanical Specifications Parameter Min Typ Max Units 1532 - 1565 nm Standard 0 - 50 °C Standard* Storage Temperature -40 - 85 °C Standard Operating Humidity 20 - 85 % Non-Condensing Operating Wavelength Operating Case Temperature Comments Voltage Supply Range - +12/+5/+3.3 - VDC All Versions** Optical Connectors - SC; FC; E2000 - - APC Only 70 x 90 x 15 - mm All Versions 2.75 x 3.5 x .59 - in Dimensions *Extended temperature range of - 40°C to +75°C is also possible **Transient Pulse to +X.X VDC + 5% for < 100 msec © 2014 EMCORE Corporation | REV 2014.02 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2OP Series EDFA Micro Erbium Doped Fiber pre-Amplifier DATASHEET | FEBRUARY 2014 SATCOM Outline Drawing (dimensions are in inches & mm) Compliance and Reliability Information FCC: Subpart B. Part 15 Class "A": Unintentional Radiators EN 55013: Sound and Television Broadcast receivers and associated equipment - Radio disturbance characteristics - limits and methods of measurements - Electric Field Radiation Emissions (2001) Fit Rate: 90% level of confidence - 325 @ 25°C © 2014 EMCORE Corporation | REV 2014.02 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. Optiva OTS-2OP Series EDFA Micro Erbium Doped Fiber pre-Amplifier DATASHEET | FEBRUARY 2014 SATCOM Ordering Information OTS - 2OP - X X X X - Y Y Y Power Level (XXXX) Connector Option (YYY) 1400 - 14 dBm SA - SC/APC SC - SC/PC FA - FC/APC FC- FC/PC E2A - E2000/APC E2C - E2000/PC Example: OTS-2OP-1400-SC: 14 dBm pre-amplified Gain Block with SC/APC optical connectors. Note: Please contact your Sales Representative for other specific requirements Laser Safety This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IIIb laser product based on the maximum optical output power shown below. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation and would meet the requirments for a Class 1 laser product. Wavelength = 1532 ~ 1565 nm (dependent on input source) Maximum Output Power = 0.2 W (single output, 23 dBm model) © 2014 EMCORE Corporation | REV 2014.02 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.