BAV23C-G3-08

BAV23C-G
www.vishay.com
Vishay Semiconductors
Small Signal Switching Diode, Dual
FEATURES
• Silicon epitaxial planar diode
3
• Fast switching dual diode with common cathode
• AEC-Q101 qualified
1
• Base P/N-G3 - green, commercial grade
2
• Material categorization: 
For definitions of compliance
www.vishay.com/doc?99912
18108_1
please
see





MECHANICAL DATA
Case: SOT-23
Weight: approx. 8.1 mg
Packaging codes/options:
18/10K per 13" reel (8 mm tape), 10K/box
08/3K per 7" reel (8 mm tape), 15K/box
PARTS TABLE
PART
BAV23C-G
ORDERING CODE
INTERNAL CONSTRUCTION
TYPE MARKING
REMARKS
BAV23C-G3-08 or BAV23C-G3-18
Dual diodes common cathode
KT7
Tape and reel
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
Continuous reverse voltage
Repetitive peak reverse voltage
SYMBOL
VALUE
UNIT
V
VR
200
VRRM
250
V
9.0
A
Non-repetitive peak forward current
t = 1 μs
IFSM
Non-repetitive peak forward surge current
t=1s
IFSM
0.5
A
IFAV
200
mA
mA
Maximum average forward rectified current (1)
Forward continuous current (2)
IF
400
Repetitive peak forward current
IFRM
625
mA
Power dissipation (2)
Ptot
350
mW
SYMBOL
VALUE
UNIT
RthJA
357
K/W
Notes
(1) Measured under pulse conditions; pulse time = t  0.3 ms
p
(2) Device on fiberglass substrate
THERMAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Thermal resistance junction to ambient air (1)
Junction temperature
TEST CONDITION
Tj
150
°C
Storage temperature range
Tstg
- 65 to + 150
°C
Operating temperature range
Top
- 55 to + 150
°C
Note
(1) Device on fiberglass substrate
Rev. 1.3, 17-May-13
Document Number: 85866
1
For technical questions within your region: [email protected], [email protected], [email protected]ishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BAV23C-G
www.vishay.com
Vishay Semiconductors
ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Breakdown voltage
TEST CONDITION
SYMBOL
MIN.
IR = 100 μA, tp = 300 μs
V(BR)
250
IF = 100 mA
MAX.
UNIT
VF
1
V
IF = 200 mA
VF
1.25
V
VR = 200 V
IR
100
nA
VR = 200 V, Tj = 150 °C
IR
100
μA
Forward voltage
Reverse current
Dynamic forward resistance
V

IF = 10 mA
rf
VR = 0 V, f = 1 MHz
CD
5
pF
IF = IR = 30 mA, iR = 3 mA,
RL = 100 
trr
50
ns
Diode capacitance
Reverse recovery time
TYP.
5
500
450
400
Ptot (mW)
350
300
250
200
150
100
50
0
0
50
100
150
Tamb (°C)
Fig. 1 - Ptot - Admissible Power Dissipation vs. Ambient Temperature
100
IFSM (A)
10
1
Tj = 25 °C - prior to surge
0.1
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
Test pulse tp (s)
Fig. 2 - IFSM - Non-Repetitive Peak Forward Current vs. Pulse Duration - Maximum Admissible Values of Square Pulses
Rev. 1.3, 17-May-13
Document Number: 85866
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BAV23C-G
www.vishay.com
Vishay Semiconductors
1.0E+0
100.0E-3
Tamb = 150 °C
10.0E-3
IF (A)
Tamb = 125 °C
Tamb = 100 °C
1.0E-3
Tamb = 75 °C
Tamb = 50 °C
100.0E-6
Tamb = 25 °C
10.0E-6
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
VF (V)
Fig. 3 - VF - Typical Forward Current vs. Forward Voltage vs. Various Temperatures
1.00E-03
1.00E-04
Tamb = 150 °C
1.00E-05
Tamb = 125 °C
IR (A)
Tamb = 100 °C
1.00E-06
Tamb = 75 °C
Tamb = 50 °C
1.00E-07
Tamb = 25 °C
1.00E-08
1.00E-09
0
50
100
150
200
250
300
VR (V)
Fig. 4 - IR - Typical Reverse Current vs. Reverse Voltage vs. Various Temperatures

Rev. 1.3, 17-May-13
Document Number: 85866
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BAV23C-G
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters (inches): SOT-23
1.15 (0.045)
0° t
o8
°
0.2 (0.008)
0.098 (0.004)
0.175 (0.007)
0.1 (0.004) max.
0.550 ref. (0.022 ref.)
0.9 (0.035)
3.1 (0.122)
2.8 (0.110)
0.5 (0.020)
0.45 (0.018)
0.45 (0.018)
0.35 (0.014)
0.35 (0.014)
0.3 (0.012)
2.6 (0.102)
2.35 (0.093)
Foot print recommendation:
1 (0.039)
0.9 (0.035)
Document no.: 6.541-5014.01-4
Rev. 8 - Date: 23.Sept.2009
17418
Rev. 1.3, 17-May-13
0.9 (0.035)
0.7 (0.028)
2 (0.079)
1.43 (0.056)
1.20 (0.047)
0.45 (0.018)
0.35 (0.014)
1 (0.039)
0.9 (0.035)
0.95 (0.037)
0.95 (0.037)
Document Number: 85866
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000