M52D16161A (2J)

ESMT
M52D16161A (2J)
Mobile SDRAM
512K x 16Bit x 2Banks
Mobile Synchronous DRAM
FEATURES
z
z
z
z
z
z
z
z
z
z
z
GENERAL DESCRIPTION
1.8V power supply
LVCMOS compatible with multiplexed address
Dual banks operation
MRS cycle with address key programs
CAS Latency (2 & 3 )
Burst Length (1, 2, 4, 8 & full page)
Burst Type (Sequential & Interleave)
EMRS cycle with address key programs.
All inputs are sampled at the positive going edge of the
system clock
Burst Read Single-bit Write operation
Special Function Support.
PASR (Partial Array Self Refresh )
TCSR (Temperature compensated Self Refresh)
DS (Driver Strength)
DQM for masking
Auto & self refresh
32ms refresh period (2K cycle)
The M52D16161A is 16,777,216 bits synchronous high data rate
Dynamic RAM organized as 2 x 524,288 words by 16 bits,
fabricated with high performance CMOS technology. Synchronous
design allows precise cycle control with the use of system clock I/O
transactions are possible on every clock cycle. Range of operating
frequencies, programmable burst length and programmable
latencies allow the same device to be useful for a variety of high
bandwidth, high performance memory system applications.
ORDERING INFORMATION
Product ID
Max Freq.
Package
Comments
M52D16161A-6TG2J
166MHz
50 Pin TSOP(II)
Pb-free
M52D16161A-7.5TG2J
133MHz
50 Pin TSOP(II)
Pb-free
M52D16161A-10TG2J
100MHz
50 Pin TSOP(II)
Pb-free
M52D16161A-6BG2J
166MHz
60 Ball VFBGA
Pb-free
M52D16161A-7.5BG2J
133MHz
60 Ball VFBGA
Pb-free
M52D16161A-10BG2J
100MHz
60 Ball VFBGA
Pb-free
PIN CONFIGURATION (TOP VIEW)
BALL CONFIGURATION (TOP VIEW)
(TSOPII 50L, 400milX825mil Body, 0.8mm Pin Pitch)
(BGA60, 6.4mmX10.1mmX1mm Body, 0.65mm Ball Pitch)
VDD
1
50
VSS
DQ0
2
49
DQ15
DQ1
3
48
DQ14
VSSQ
4
47
VSSQ
DQ2
5
46
DQ13
DQ3
6
45
DQ12
VDDQ
7
44
VDDQ
DQ4
8
43
DQ11
DQ5
9
42
DQ10
VSSQ
10
41
VSSQ
DQ6
11
40
DQ9
DQ7
12
39
DQ8
VDDQ
13
38
VDDQ
LDQM
14
37
N.C/RFU
WE
15
36
UDQM
CAS
16
35
CLK
RAS
17
34
CKE
CS
18
33
N.C
BA
19
32
A9
A10/AP
20
31
A8
A0
21
30
A7
A1
22
29
A6
A2
23
28
A5
A3
24
27
A4
VDD
25
26
VSS
50PIN TSOP(II)
(400mil x 825mil)
(0.8 mm PIN PITCH)
Elite Semiconductor Memory Technology Inc.
1
2
6
7
A
VSS
DQ15
3
4
5
DQ0
VDD
B
DQ14
VSSQ
VDDQ
DQ1
C
DQ13
VDDQ
VSSQ
DQ2
D
DQ12
DQ11
DQ4
DQ3
E
DQ10
VSSQ
VDDQ
DQ5
F
DQ9
VDDQ
VSSQ
DQ6
G
DQ8
NC
NC
DQ7
H
NC
NC
NC
NC
J
NC
UDQM
LDQM
WE
K
NC
CLK
RAS
CAS
L
CKE
NC
NC
CS
M
BA
A9
NC
NC
N
A8
A7
A0
A10
P
A6
A5
A2
A1
R
VSS
A4
A3
VDD
60 Ball VFBGA
(6.4x10.1mm)
(0.65mm ball pitch)
Publication Date : Jun. 2010
Revision : 1.5
1/32
ESMT
M52D16161A (2J)
FUNCTIONAL BLOCK DIAGRAM
512K x 16
LWE
LDQM
Output Buffer
Col. Buffer
LCKE
512K x 16
Sense AMP
Row Decoder
LRAS
LCBR
ADD
Row Buffer
Refresh Counter
Address Register
CLK
Data Input Register
I/O Control
Bank Select
DQi
Column Decoder
Latency & Burst Length
Programming Register
LRAS
LCBR
LWE
LCAS
LWCBR
LDQM
Timing Register
CLK
CKE
CS
RAS
CAS
WE
L(U)DQM
PIN FUNCTION DESCRIPTION
CLK
Pin
Name
System Clock
CS
Chip Select
CKE
Clock Enable
A0 ~ A10/AP
Address
BA
Bank Select Address
RAS
Row Address Strobe
CAS
Column Address Strobe
WE
Write Enable
L(U)DQM
Data Input / Output Mask
DQ0 ~ 15
VDD/VSS
Data Input / Output
Power Supply/Ground
VDDQ/VSSQ
Data Output Power/Ground
N.C/RFU
No Connection/
Reserved for Future Use
Elite Semiconductor Memory Technology Inc.
Input Function
Active on the positive going edge to sample all inputs.
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and L(U)DQM.
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
Row / column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA10, column address : CA0 ~ CA7
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
Latches column addresses on the positive going edge of the CLK with
CAS low.
Enables column access.
Enables write operation and row precharge.
Latches data in starting from CAS , WE active.
Makes data output Hi-Z, tSHZ after the clock and masks the output.
Blocks data input when L(U)DQM active.
Data inputs/outputs are multiplexed on the same pins.
Power and ground for the input buffers and the core logic.
Isolated power supply and ground for the output buffers to provide improved
noise immunity.
This pin is recommended to be left No Connection on the device.
Publication Date : Jun. 2010
Revision : 1.5
2/32
ESMT
M52D16161A (2J)
ABSOLUTE MAXIMUM RATINGS
Parameter
Voltage on any pin relative to VSS
Voltage on VDD supply relative to VSS
Storage temperature
Power dissipation
Short circuit current
Symbol
Value
Unit
VIN,VOUT
VDD,VDDQ
TSTG
PD
IOS
-1.0 ~ 2.6
-1.0 ~ 2.6
-55 ~ + 150
0.7
50
V
V
°C
W
mA
Note: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to VSS = 0V, TA = 0 °C ~ 70 °C )
Parameter
Supply voltage
Input logic high voltage
Input logic low voltage
Output logic high voltage
Output logic low voltage
Input leakage current
Output leakage current
Note:
Symbol
Min
Typ
Max
Unit
Note
VDD,VDDQ
VIH
VIL
VOH
VOL
IIL
IOL
1.7
0.8 x VDDQ
-0.3
VDDQ - 0.2
-10
-10
1.8
1.8
0
-
1.9
VDDQ+0.3
0.3
0.2
10
10
V
V
V
V
V
uA
uA
1
2
IOH =-0.1mA
IOL = 0.1mA
3
4
1.VIH (max) = 2.2V AC for pulse width ≤ 3ns acceptable.
2.VIL (min) = -1.0V AC for pulse width ≤ 3ns acceptable.
3.Any input 0V ≤ VIN ≤ VDDQ, all other pins are not under test = 0V.
4.Dout is disabled, 0V ≤ VOUT ≤ VDDQ.
CAPACITANCE (VDD = 1.8V, TA = 25 °C , f = 1MHz)
Pin
Symbol
Min
Max
Unit
CLOCK
CCLK
2.0
4.0
pF
CIN
2.0
4.0
pF
CADD
COUT
2.0
3.5
4.0
6.0
pF
pF
RAS , CAS , WE , CS , CKE, LDQM,
UDQM
ADDRESS
DQ0 ~DQ15
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
3/32
ESMT
M52D16161A (2J)
DC CHARACTERISTICS
(Recommended operating condition unless otherwise noted, TA = 0 °C ~ 70 °C )
Parameter
Operating Current
(One Bank Active)
Precharge Standby
Current in power-down
mode
Precharge Standby
Current in non
power-down mode
Active Standby Current
in power-down mode
Symbol
Version
Test Condition
-6
-7.5
-10
50
45
40
Unit Note
ICC1
Burst Length = 1
tRC ≥ tRC (min), tCC ≥ tCC (min), IOL= 0mA
ICC2P
CKE ≤ VIL(max), tCC =15ns
0.18
mA
ICC2PS
CKE ≤ VIL(max), CLK ≤ VIL(max), tCC = ∞
0.15
mA
5.5
mA
1
mA
ICC2N
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 15ns
Input signals are changed one time during 30ns
ICC2NS
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable
ICC3P
CKE ≤ VIL(max), tCC =15ns
ICC3PS
CKE ≤ VIL(max), CLK ≤ VIL(max), tCC = ∞
2.5
mA
1
mA
2
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 15ns
Active Standby Current
in non power-down
mode
(One Bank Active)
ICC3N
Input signals are changed one time during 2clks
12
mA
6
mA
All other pins ≥ VDD-0.2V or ≤ 0.2V
ICC3NS
CKE ≥ VIH (min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable
Operating Current
(Burst Mode)
ICC4
IOL= 0mA, Page Burst
All Band Activated, tCCD = tCCD (min)
70
65
60
mA
1
Refresh Current
ICC5
tRFC ≥ tRFC(min)
55
50
45
mA
2
Self Refresh Current
Deep Power Down
Current
ICC6
ICC7
CKE ≤ 0.2V
TCSR range
15
85
2 Banks
160
180
1 Bank
140
160
1/2 Bank
130
140
CKE ≤ 0.2V
10
°C
uA
uA
Note: 1.Measured with outputs open. Addresses are changed only one time during tCC(min).
2.Refresh period is 32ms. Addresses are changed only one time during tCC(min).
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
4/32
ESMT
M52D16161A (2J)
AC OPERATING TEST CONDITIONS (VDD = 1.8V ± 0.1V, TA = 0 °C ~ 70 °C )
Parameter
Input levels (Vih/Vil)
Input timing measurement reference level
Input rise and fall time
Output timing measurement reference level
Output load condition
Value
0.9 x VDDQ / 0.2
0.5 x VDDQ
tr / tf = 1 / 1
0.5 x VDDQ
See Fig.2
Unit
V
V
ns
V
1.8V
Vtt =0.5x VDDQ
13.9K
50
Output
VOH(DC) = VDDQ-0.2V, IOH = -0.1mA
VOL(DC) = 0.2V, IOL = 0.1mA
10.6K
Output
Z0=50
20 pF
20 pF
(Fig.2) AC Output Load Circuit
(Fig.1) DC Output Load circuit
OPERATING AC PARAMETER
(AC operating conditions unless otherwise noted)
Parameter
Symbol
Version
-6
-7.5
-10
Unit
Note
Row active to row active delay
tRRD(min)
12
15
20
ns
1
RAS to CAS delay
tRCD(min)
18
22.5
30
ns
1
Row precharge time
tRP(min)
18
22.5
30
ns
1
tRAS(min)
30
37.5
50
ns
1
Row active time
tRAS(max)
100
us
@ Operating
tRC(min)
60
67.5
80
ns
1
@ Auto refresh
tRFC(min)
66
67.5
80
ns
1,5
Last data in to new col. Address delay
tCDL(min)
1
CLK
2
Last data in to row precharge
tRDL(min)
2
CLK
2
Last data in to burst stop
tBDL(min)
1
CLK
2
Col. Address to col. Address delay
tCCD(min)
1
CLK
3
ea
4
Row cycle time
Number of valid output data
CAS latency = 3
2
CAS latency = 2
1
Note: 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and
then rounding off to the next higher integer.
2. Minimum delay is required to complete write.
3. All parts allow every cycle column address change.
4. In case of row precharge interrupt, auto precharge and read burst stop.
The earliest a precharge command can be issued after a Read command without the loss of data is CL+BL-2 clocks.
5. A new command may be given tRFC after self refresh exit.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
5/32
ESMT
M52D16161A (2J)
AC CHARACTERISTICS (AC operating conditions unless otherwise noted)
Parameter
CLK cycle time
CLK to valid
output delay
CAS Latency = 3
CAS Latency = 2
CAS Latency = 3
CAS Latency = 2
Symbol
tCC
tSAC
-6
Min
6
10
-7.5
Max
1000
Min
7.5
12
-10
Max
1000
Min
10
15
Max
1000
-
5.5
-
6
-
9
-
9
-
10
-
12
Unit Note
ns
1
ns
1
Output data hold time
tOH
2.5
-
2.5
-
2.5
-
ns
2
CLK high pulse width
tCH
2.5
-
2.5
-
3
-
ns
3
CLK low pulse width
tCL
2.5
-
2.5
-
3
-
ns
3
Input setup time
tSS
2
-
2.5
-
3
-
ns
3
Input hold time
tSH
1
-
1
-
1
-
ns
3
CLK to output in Low-Z
tSLZ
1
-
1
-
1
-
ns
2
-
5.5
-
6
-
9
-
9
-
10
-
12
ns
-
CLK to output
in Hi-Z
CAS Latency = 3
CAS Latency = 2
tSHZ
*All AC parameters are measured from half to half.
Note: 1.Parameters depend on programmed CAS latency.
2.If clock rising time is longer than 1ns,(tr/2-0.5)ns should be added to the parameter.
3.Assumed input rise and fall time (tr & tf)=1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered, i.e., [(tr+ tf)/2-1]ns should be added to the
parameter.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
6/32
ESMT
M52D16161A (2J)
Mode Register
BA
x
A10
x
0
0
A9
1
A8
0
A7
0
0
0
0
A6
A5 A4
LTMODE
A3
WT
LTMODE
WT
A2
A1 A0
BL
BL
Address bus
Burst Read and Single Write (for Write
Through Cache)
Mode Register Set
x =Don’t care
A2-A0
000
001
010
011
100
101
110
111
Burst length
0
1
Wrap type
A6-A4
000
001
010
011
100
101
110
111
Latency mode
WT=0
1
2
4
8
R
R
R
Full page
WT=1
1
2
4
8
R
R
R
R
Sequential
Interleave
CAS Latency
R
R
2
3
R
R
R
R
Remark R: Reserved
Mode Register Write Timing
CLOCK
CKE
CS
RAS
CAS
WE
A0-A10,BA
Mode Register Write
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
7/32
ESMT
M52D16161A (2J)
Extended Mode Register
BA
1
A10
0
A9
0
A8
0
A7
0
A6
A5
DS
A4
X
Elite Semiconductor Memory Technology Inc.
A3
X
A2
A1 A0
PASR
Address bus
Extended Mode Register Set
x =Don’t care
PASR
A2-A0
000
001
010
011
100
101
110
111
Self Refresh Coverage
2 Banks
1 Bank (Bank 0, BA=0)
1/2 Bank (BA=A10=0)
R
R
1/4 Bank (BA=A10=A9=0)
R
R
DS
A6-A5
00
01
10
11
Driver Strength
Full Strength
1/2 Strength
1/4 Strength
R
Remark R : Reserved
Publication Date : Jun. 2010
Revision : 1.5
8/32
ESMT
M52D16161A (2J)
Burst Length and Sequence
(Burst of Two)
Starting Address
(column address A0 binary)
0
1
Sequential Addressing
Sequence (decimal)
0,1
1,0
Interleave Addressing
Sequence (decimal)
0,1
1,0
Sequential Addressing
Sequence (decimal)
0,1,2,3
1,2,3,0
2,3,0,1
3,0,1,2
Interleave Addressing
Sequence (decimal)
0,1,2,3
1,0,3,2
2,3,0,1
3,2,1,0
(Burst of Four)
Starting Address
(column address A1-A0, binary)
00
01
10
11
(Burst of Eight)
Starting Address
(column address A2-A0, binary)
000
001
010
0 11
100
101
11 0
111
Sequential Addressing
Sequence (decimal)
0,1,2,3,4,5,6,7
1,2,3,4,5,6,7,0
2,3,4,5,6,7,0,1
3,4,5,6,7,0,1,2
4,5,6,7,0,1,2,3
5,6,7,0,1,2,3,4
6,7,0,1,2,3,4,5
7,0,1,2,3,4,5,6
Interleave Addressing
Sequence (decimal)
0,1,2,3,4,5,6,7
1,0,3,2,5,4,7,6
2,3,0,1,6,7,4,5
3,2,1,0,7,6,5,4
4,5,6,7,0,1,2,3
5,4,7,6,1,0,3,2
6,7,4,5,2,3,0,1
7,6,5,4,3,2,1,0
Full page burst is an extension of the above tables of Sequential Addressing, with the length being 256 for 1Mx16 device.
POWER UP SEQUENCE
1.Apply power and start clock, attempt to maintain CKE= “H”, L(U)DQM = “H” and the other pin are NOP condition at the inputs.
2.Maintain stable power, stable clock and NOP input condition for a minimum of 200us.
3.Issue precharge commands for all banks of the devices.
4.Issue 2 or more auto-refresh commands.
5.Issue mode register set command to initialize the mode register.
6.Issue an extended mode register set command to define special function of the device after normal MRS.
Cf.)Sequence of 4~6 is regardless of the order.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
9/32
ESMT
M52D16161A (2J)
SIMPLIFIED TRUTH TABLE
COMMAND
CKEn-1 CKEn CS
Mode Register Set
H
X
L
Register
Extended Mode Register
H
X
L
Set
Auto Refresh
H
H
L
Entry
L
Refresh
Self Refresh
L
Exit
L
H
H
Bank Active & Row Addr.
H
X
L
Read &
Column Address
Auto Precharge Disable
Auto Precharge Enable
Auto Precharge Disable
Write & Column
Address
Burst Stop
Auto Precharge Enable
Precharge
Bank Selection
Both Banks
Clock Suspend or
Active Power Down
Deep Power Down Mode
L
L
L
X
OP CODE
L
L
H
X
X
H
X
L
H
X
H
H
X
H
X
X
X
V
L
H
L
H
X
V
H
X
L
H
L
L
X
V
H
X
L
H
H
L
X
Entry
H
L
Exit
L
H
Entry
H
L
Exit
L
H
Entry
Exit
H
H
H
H
L
No Operation Command
WE
L
X
X
DQM
CAS
L
H
H
Precharge Power Down Mode
DQM BA A10/AP A9~A0 Note
X
OP CODE
1,2
RAS
L
X
L
H
L
L
H
L
H
L
X
H
L
H
L
X
V
X
X
H
X
V
X
X
H
H
X
X
V
X
X
H
X
V
X
V
X
X
H
X
V
X
H
H
X
X
H
L
X
H
L
L
X
X
X
1,2
3
3
3
3
Row Address
Column
4
Address
(A0~A7) 4,5
Column
4
Address
4,5
(A0~A7)
L
H
L
H
X
V
X
L
H
X
6
4
4
X
X
X
X
X
V
X
X
X
X
X
X
7
(V= Valid, X= Don’t Care, H= Logic High, L = Logic Low)
Note:
1. OP Code: Operation Code
A0~ A10/AP, BA: Program keys.(@MRS). BA=0 for MRS and BA=1 for EMRS.
2. MRS/EMRS can be issued only at both banks precharge state.
A new command can be issued after 2 clock cycle of MRS.
3. Auto refresh functions are as same as CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by “Auto”.
Auto / self refresh can be issued only at both banks precharge state.
4. BA: Bank select address.
If “Low”: at read, write, row active and precharge, bank A is selected.
If “High”: at read, write, row active and precharge, bank B is selected.
If A10/AP is “High” at row precharge, BA ignored and both banks are selected.
5. During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read /write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6. Burst stop command is valid at every burst length.
7. DQM sampled at positive going edge of a CLK masks the data-in at the very CLK (Write DQM latency is 0), but
makes Hi-Z state the data-out of 2 CLK cycles after. (Read DQM latency is 2)
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
10/32
ESMT
M52D16161A (2J)
Single Bit Read-Write-Read Cycle (Same Page) @ CAS Latency = 3, Burst Length = 1
tCH
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
tCL
tCC
HIGH
CKE
tRAS
tRC
*Note1
tSH
CS
tRP
tRCD
tSS
tSH
RAS
tSS
tCCD
tSH
CAS
tSS
tSS
tSH
ADDR
Ra
Ca
Cb
*Note2
Rb
Cc
tSH
tSS
*Note2,3
BA
BS
BS
A10 /AP
Ra
*Note 3
*Note2,3
*Note2,3
BS
BS
*Note 3
*Note 3
*Note4
*Note2
BS
BS
*Note4
Rb
tRAC
tSAC
tSH
DQ
tSLZ
Qc
Db
Qa
tSS
tOH
tSH
WE
tSS
tSS
tSH
DQM
Row Active
Read
W rite
Read
Row Active
Precharge
:D on' t Care
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
11/32
ESMT
M52D16161A (2J)
*Note: 1. All inputs expect CKE & DQM can be don’t care when CS is high at the CLK high going edge.
2. Bank active & read/write are controlled by BA.
BA
Active & Read/Write
0
Bank A
1
Bank B
3. Enable and disable auto precharge function are controlled by A10/AP in read/write command.
A10/AP
0
1
BA
Operation
0
Disable auto precharge, leave bank A active at end of burst.
1
Disable auto precharge, leave bank B active at end of burst.
0
Enable auto precharge, precharge bank A at end of burst.
1
Enable auto precharge, precharge bank B at end of burst.
4. A10/AP and BA control bank precharge when precharge command is asserted.
A10/AP
BA
Precharge
0
0
Bank A
0
1
Bank B
1
X
Both Banks
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
12/32
ESMT
M52D16161A (2J)
Power Up Sequence
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CLOCK
CKE
High level is necessary
CS
tRFC
tRFC
tRP
RAS
CAS
ADDR
Key
Key
RAa
Key
Key
RAa
BA
A10/AP
High-Z
DQ
WE
DQM
High level is necessary
Precharge
All Banks
Auto Refresh
Auto Refresh
Mode Register Set
(A-Bank)
Row Active
Extended Mode Register
Set
: Don't care
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
13/32
ESMT
M52D16161A (2J)
Read & Write Cycle at Same Bank @ Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
t RC
*Note1
CS
tRCD
RAS
*Note 2
CAS
ADDR
Ra
Rb
Ca0
Cb0
BA
A10 /AP
Ra
Rb
t OH
CL =2
Qa0
t R AC
QC
Qa2
Qa1
t S AC
*Note3
CL =3
t R AC
Qa3
tO H
Qa1
Qa0
*No te3
Db0
t SH Z
Qa2
Db1
Db2
Db3
*Note4
t RDL
Qa3
Db0
t S HZ
t S AC
Db1
*Note4
Db2
Db3
t RDL
WE
DQM
Row Active
(A-Ba nk )
Read
(A-B ank )
Precharge
Row Active
(A-Ban k)
(A-Ba nk )
W ri te
(A-Ban k)
Precharge
(A-Ban k)
: Don't care
*Note: 1.Minimum row cycle times is required to complete internal DRAM operation.
2.Row precharge can interrupt burst on any cycle. [CAS Latency-1] number of valid output data is available after Row
precharge. Last valid output will be Hi-Z(tSHZ) after the clock.
3.Access time from Row active command. tcc*(tRCD +CAS latency-1)+tSAC
4.Output will be Hi-Z after the end of burst.(1,2,4,8 bit burst)
Burst can’t end in Full Page Mode.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
14/32
ESMT
M52D16161A (2J)
Page Read & Write Cycle at Same Bank @ Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
CS
tRCD
RAS
*Note2
CAS
ADDR
Ra
Ca0
Cb0
Cc0
Cd0
BA
A10/AP
Ra
tRDL
CL=2
Qa0
Qa1
Qb0
Qb1
Qb2
Dc0
Qa0
Qa1
Qb0
Qb1
Dc0
Dc1
Dd0
Dd1
DQ
CL=3
Dc1
Dd0
Dd2
tCDL
WE
*Note3
*Note1
DQM
Row Active
(A-Bank)
Read
(A-Bank)
Read
(A-Bank)
Write
(A-Bank)
Write
(A-Bank)
Precharge
(A-Bank)
: Don't care
*Note: 1.To write data before burst read ends, DQM should be asserted three cycle prior to write command to avoid bus
contention.
2.Row precharge will interrupt writing. Last data input, tRDL before Row precharge, will be written.
3.DQM should mask invalid input data on precharge command cycle when asserting precharge before end of burst.
Input data after Row precharge cycle will be masked internally.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
15/32
ESMT
M52D16161A (2J)
Page Read Cycle at Different Bank @ Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
HIGH
*Note1
CS
RAS
*Note2
CAS
ADDR
RAa
CAa
CAc
CBb
RBb
CBd
CAe
BA
A10/AP
RAa
RBb
CL=2
QAa0
QAa1
QAa2
QAa3
QBb0
QBb1
QBb2
QBb3
QAc0
QAc1
QBd0
QBd1
QAe0
QAe1
QAa0
QAa1
QAa2
QAa3
QBb0
QBb1
QBb2 QBb3
QAc0
QAc1
QBd0
QBd1
QAe0
DQ
CL=3
QAe1
WE
DQM
Row Active
(A-Bank)
Read
(A-Bank)
Read
(B-Bank)
Read
(A-Bank)
Read
(B-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Row Active
(B-Bank)
: Don't care
*Note: 1. CS can be don’t cared when RAS , CAS and WE are high at the clock high going edge.
2.To interrupt a burst read by row precharge, both the read and the precharge banks must be the same.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
16/32
ESMT
M52D16161A (2J)
Page Write Cycle at Different Bank @ Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
CS
RAS
CAS
*Note2
ADDR
RAa
CAa
CBb
RBb
CAc
CBd
BA
A10/AP
RAa
DQ
RBb
DAa0
DAa1
DAa2
DAa3
DBb0
DBb1
DBb2 DBb3
DAc0
DAc1
DBd0
tCDL
DBd1
tRDL
WE
*Note1
DQM
Row Active
(A-Bank)
Row Active
(B-Bank)
Write
(A-Bank)
Write
(B-Bank)
Precharge
(Both Banks)
Write
(A-Bank)
Write
(B-Bank)
: Don't care
*Note: 1.To interrupt burst write by Row precharge, DQM should be asserted to mask invalid input data.
2.To interrupt burst write by row precharge, both the write and the precharge banks must be the same.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
17/32
ESMT
M52D16161A (2J)
Read & Write Cycle at Different Bank @ Burst Length = 4
*Note: 1.tCDL should be met to complete write.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
18/32
ESMT
M52D16161A (2J)
Read & Write Cycle with auto Precharge @ Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
CS
RAS
CAS
ADDR
Ra
Rb
Ra
Rb
Cb
Ca
BA
A10 /A P
CL= 2
Qa0
Q a1
Qa2
Q a3
Q a1
Qa2
Db0
Db1
Db2
Db3
Db0
Db1
Db2
Db3
DQ
CL=3
Q a0
Qa3
WE
DQM
Row Active
( A - Bank )
Read with
Auto Precharge
( A - Bank )
Auto Precharge
Start Point
( A - Bank)
W rite with
Auto Pr echarge
( B- Bank )
Auto Pr echarge
Star t Poin t
( B- Bank )
Row Active
( B - Bank )
:D on' t Ca re
*Note: 1.tCDL should be controlled to meet minimum tRAS before internal precharge start
(In the case of Burst Length=1 & 2 and BRSW mode)
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
19/32
ESMT
M52D16161A (2J)
Clock Suspension & DQM Operation Cycle @ CAS Latency = 2, Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
CS
RAS
CAS
ADDR
Ra
Ca
Cb
Cc
BA
A10 /AP
Ra
Q a0
DQ
Qa1
Q a2
Qb0
Q a3
tSHZ
Q b1
Dc2
Dc 0
tSHZ
WE
*Note1
DQM
Row Active
Read
Clock
Suspension
Read
W rite
DQM
Read DQM
W rite
W rite
DQM
Cloc k
Sus pension
:Don't Car e
*Note: 1.DQM is needed to prevent bus contention.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
20/32
ESMT
M52D16161A (2J)
Read Interrupted by Precharge Command & Read Burst Stop Cycle @ Burst Length = Full page
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
CS
RAS
CAS
ADDR
RAa
CAa
CAb
BA
A10 /AP
RAa
*Note2
1
1
QAa0 QAa1 QAa2 QAa 3 QAa4
CL=2
DQ
QAb0 QAb1 QAb 2 QAb3 QAb4 QAb5
2
2
CL=3
QAa0 QAa1 QAa 2 QAa3 QAa4
WE
QAb0 QAb1 QAb2 QAb3 QAb4 QAb5
*Note1
DQM
Row Active
( A- B an k )
Read
(A- Ban k)
Burst Stop
Read
(A- Ban k)
Precharge
( A- B an k )
:Don't Care
*Note: 1.Burst can’t end in full page mode, so auto precharge can’t issue.
2.About the valid DQs after burst stop, it is same as the case of RAS interrupt.
Both cases are illustrated above timing diagram. See the label 1, 2 on them.
But at burst write, burst stop and RAS interrupt should be compared carefully.
Refer the timing diagram of “Full page write burst stop cycle”.
3.Burst stop is valid at every burst length.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
21/32
ESMT
M52D16161A (2J)
Write Interrupted by Precharge Command & Write Burst stop Cycle @ Burst Length = Full page
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
CS
RAS
CAS
RAa
ADDR
CAa
CAb
BA
A10 /AP
RAa
tBDL
tRDL
*Note2
DQ
DAa0 DAa1 DAa2 DAa3 DAa4
DAb0 DAb1 DAb2 DAb3 DAb4 DAb5
WE
DQM
Row Active
( A- B an k )
W rite
(A- Ban k )
Burst Stop
W rite
(A- Ban k )
Precharge
( A- B an k )
:Don't Care
*Note: 1. Burst can’t end in full page mode, so auto precharge can’t issue.
2. Data-in at the cycle of interrupted by precharge can not be written into the corresponding memory cell. It is defined by
AC parameter of tRDL.
DQM at write interrupted by precharge command is needed to prevent invalid write.
Input data after Row precharge cycle will be masked internally.
3. Burst stop is valid at every burst length.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
22/32
ESMT
M52D16161A (2J)
Burst Read Single bit Write Cycle @ Burst Length = 2
CLOCK
*Note1
HIGH
CKE
CS
RAS
*Note2
CAS
ADDR
RAa
CAa
RBb
CAb
CBc
RAc
CAd
BA
A10 /AP
RAa
RAc
RBb
CL=2
DAa0
CL= 3
DAa0
QAb0 QAb1
QAd0 QAd1
DBc0
DQ
QAb0 QAb1
QAd0 QAd1
DBc0
WE
DQM
Row Active
( A- B an k )
Row Active
(B-Bank)
W rite
(A- Ban k)
Read with
Auto Precharge
(A-Bank)
Read
( A- B an k )
Row Act ive
( A- B an k )
Precharge
( A- B an k )
W rite with
Auto Pr echarge
( B- Bank )
:Don't Care
*Note: 1. BRSW modes is enabled by setting A9 “High” at MRS(Mode Register Set).
At the BRSW Mode, the burst length at write is fixed to “1” regardless of programmed burst length.
2. When BRSW write command with auto precharge is executed, keep it in mind that tRAS should not be violated.
Auto precharge is executed at the next cycle of burst-end, so in the case of BRSW write command, the precharge
command will be issued after two clock cycles.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
23/32
ESMT
M52D16161A (2J)
Active/Precharge Power Down Mode @ CAS Latency = 2, Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Q a0
Qa1
16
17
18
19
CLOCK
*Note2
tSS
CKE
tS S
*Note1
tS S
*Not e3
CS
RAS
CAS
Ra
ADDR
Ca
BA
A10 /A P
Ra
tSHZ
DQ
Qa2
WE
DQM
Pr ech ar ge
Pow er - Dow n
Entry
Row Active
Precharge
Power-Down
Exit
Active
Power-down
Entry
Read
Precharge
Active
Power-down
Exit
: Don't care
*Note: 1. Both banks should be in idle state prior to entering precharge power down mode.
2. CKE should be set high at least 1CLK+tss prior to Row active command.
3. Can not violate minimum refresh specification. (32ms)
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
24/32
ESMT
M52D16161A (2J)
Deep Power Down Mode Entry & Exit Cycle
Note:
DEFINITION OF DEEP POWER MODE FOR Mobile SDRAM:
Deep Power Down Mode is an operating mode to achieve maximum power reduction by cutting the power of the whole memory
of the device. Once the device enters in Deep Power Down Mode, data will not be retained. Full initialization is required when
the device exits from Deep Power Down Mode.
TO ENTER DEEP POWER DOWN MODE
1) The deep power down mode is entered by having CS and WE held low with RAS and CAS high at the rising edge of
the clock. While CKE is low.
2) Clock must be stable before exited deep power down mode.
3) Device must be in the all banks idle state prior to entering Deep Power Down mode.
TO EXIT DEEP POWER DOWN MODE
4) The deep power down mode is exited by asserting CKE high.
5) 200μs wait time is required to exit from Deep Power Down.
6) Upon exiting deep power down an all bank precharge command must be issued followed by two auto refresh commands
and a load mode register sequence.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
25/32
ESMT
M52D16161A (2J)
Self Refresh Entry & Exit Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
*No te2
*Note4
t RFCmin
*Note6
*Note1
*Note3
CKE
tSS
CS
*Note5
RAS
*Note7
CAS
ADDR
BA
A10/AP
Hi-Z
DQ
Hi-Z
WE
DQM
Self Refresh Entry
Self Refresh Exit
Auto Refresh
: Don't care
*Note: TO ENTER SELF REFRESH MODE
1. CS , RAS & CAS with CKE should be low at the same clock cycle.
2. After 1 clock cycle, all the inputs including the system clock can be don’t care except for CKE.
3. The device remains in self refresh mode as long as CKE stays “Low”.
cf.) Once the device enters self refresh mode, minimum tRAS is required before exit from self refresh.
TO EXIT SELF REFRESH MODE
4. System clock restart and be stable before returning CKE high.
5. CS Starts from high.
6. Minimum tRFC is required after CKE going high to complete self refresh exit.
7. 2K cycles of burst auto refresh is required immediately before self refresh entry and immediately after self refresh
exit.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
26/32
ESMT
M52D16161A (2J)
Mode Register Set Cycle
0
1
2
3
4
5
Auto Refresh Cycle
6
0
1
2
3
4
5
6
7
8
9
10
CLOCK
HIGH
CKE
HIGH
CS
*Note2
tRFC
RAS
*Note1
CAS
*Note3
Key
ADDR
Ra
BA
DQ
Hi-Z
Hi-Z
WE
DQM
MRS
New Comm and
Auto Refresh
New Command
:Don't Care
*Both banks precharge should be completed before Mode Register Set cycle and auto refresh cycle.
MODE REGISTER SET CYCLE
*Note: 1. CS , RAS , CAS & WE activation at the same clock cycle with address key will set internal mode register.
2.Minimum 2 clock cycles should be met before new RAS activation.
3.Please refer to Mode Register Set table.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
27/32
ESMT
M52D16161A (2J)
Extended Mode Register Set Cycle
0
1
2
3
4
5
6
CLOCK
HIGH
CKE
CS
*Note2
RAS
*Note1
CAS
*Note3
Key
ADDR
Ra
BA
DQ
Hi-Z
WE
DQM
EMRS
New Command
:Don't Care
*Both banks precharge should be completed before Extended Mode Register Set cycle.
EXTENDED MODE REGISTER SET CYCLE
*Note: 1. CS , RAS , CAS & WE activation at the same clock cycle with address key will set internal extended mode register.
2.Minimum 2 clock cycles should be met before new RAS activation.
3.Please refer to Extended Mode Register Set table.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
28/32
ESMT
M52D16161A (2J)
PACKAGE DIMENSIONS
50-LEAD TSOP(II) SDRAM (400mil)
26
50
C1
C
E
E1
B
B1
WITH PLATING
BASE METAL
SECTION Y-Y
1
Y Y
25
"A"
e
GAGE PLANE
D
Y
Symbol
A
A1
A2
B
B1
C
C1
D
E
E1
L
L1
e
Y
θ
Min
0.051
0.95
0.30
0.30
0.12
0.10
20.82
11.56
10.03
0.40
0
SEATING PLANE
Dimension in mm
Nom
0.127
1.00
0.35
0.127
20.95
11.76
10.16
0.50
0.80 REF
0.80 BSC
-
A
L
L1
A1
A2
θ°
DETAIL "A"
Max
1.20
0.203
1.05
0.45
0.40
0.21
0.16
21.08
11.96
10.29
0.60
Min
0.002
0.037
0.012
0.012
0.005
0.004
0.820
0.455
0.394
0.016
0.1
8
0
Dimension in inch
Nom
0.005
0.039
0.014
0.005
0.825
0.463
0.400
0.020
0.031 REF
0.031 BSC
-
Max
0.047
0.008
0.041
0.018
0.016
0.008
0.006
0.830
0.471
0.405
0.024
0.004
8
Controlling dimension : Millimeter
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
29/32
ESMT
PACKING
60-BALL
M52D16161A (2J)
DIMENSIONS
SDRAM ( 6.4x10.1 mm )
Symbol
A
A1
A2
Φb
D
E
D1
E1
e
Dimension in mm
Min
Norm
Max
1.00
0.20
0.25
0.30
0.61
0.66
0.71
0.30
0.35
0.40
6.30
6.40
6.50
10.00
10.10
10.20
3.90
9.10
0.65
Dimension in inch
Min
Norm
Max
0.039
0.008
0.010
0.012
0.024
0.026
0.028
0.012
0.014
0.016
0.248
0.252
0.256
0.394
0.398
0.402
0.154
0.358
0.026
Controlling dimension : Millimeter.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
30/32
ESMT
M52D16161A (2J)
Revision History
Revision
Date
0.1
2008.01.14
Original
0.2
2008.05.09
Add speed grade -7.5 spec.
0.3
2008.05.15
1. Add Revision History
2. Modify absolute max. value of VIN, VOUT, VDD, VDDQ
3. Modify ICC3N test condition
1.0
2008.07.29
1. Delete “Preliminary”
2. Modify title
3. Modify tSS(min)
1.1
2008.10.03
1. Add tRFC spec.
2. Modify tRP and tRC spec.
3. Modify the description about self refresh operation
1.2
2009.07.27
Add the description of Deep Power Down Mode
1.3
2010.04.27
Add package description into pin / ball configuration
1.4
2010.05.19
1. Modify the specification of ICC3P and ICC3PS
2. Correct Power Up Sequence for EMRS and add the
chart of EMRS
1.5
2010.06.09
Modify Outline Coplanarity
Elite Semiconductor Memory Technology Inc.
Description
Publication Date : Jun. 2010
Revision : 1.5
31/32
ESMT
M52D16161A (2J)
Important Notice
All rights reserved.
No part of this document may be reproduced or duplicated in any form or by
any means without the prior permission of ESMT.
The contents contained in this document are believed to be accurate at the
time of publication. ESMT assumes no responsibility for any error in this
document, and reserves the right to change the products or specification in
this document without notice.
The information contained herein is presented only as a guide or examples
for the application of our products. No responsibility is assumed by ESMT for
any infringement of patents, copyrights, or other intellectual property rights of
third parties which may result from its use. No license, either express ,
implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of ESMT or others.
Any semiconductor devices may have inherently a certain rate of failure. To
minimize risks associated with customer's application, adequate design and
operating safeguards against injury, damage, or loss from such failure,
should be provided by the customer when making application designs.
ESMT's products are not authorized for use in critical applications such as,
but not limited to, life support devices or system, where failure or abnormal
operation may directly affect human lives or cause physical injury or property
damage. If products described here are to be used for such kinds of
application, purchaser must do its own quality assurance testing appropriate
to such applications.
Elite Semiconductor Memory Technology Inc.
Publication Date : Jun. 2010
Revision : 1.5
32/32