IS66WVD1M16ALL

IS66WVD1M16ALL
16Mb Async and Burst CellularRAM 2.0
Overview
The IS66WVD1M16ALL is an integrated memory device containing 16Mbit Pseudo Static Random
Access Memory using a self-refresh DRAM array organized as 1M words by 16 bits. The device uses a
multiplexed address and data bus scheme to minimize pins and includes a industry standard burst
mode for increased read and write bandwidth. The device includes several power saving modes :
Reduced Array Refresh mode where data is retained in a portion of the array and Temperature
Controlled Refresh. Both these modes reduce standby current drain. The device can be operated in a
standard asynchronous mode and high performance burst mode. The die has separate power rails,
VDDQ and VSSQ for the I/O to be run from a separate power supply from the device core.
Features
 Single device supports asynchronous and burst
operation
 Mixed Mode supports asynchronous write and
synchronous read operation
 Dual voltage rails for optional performance
 VDD 1.7V~1.95V, VDDQ 1.7V~1.95V
 Multiplexed address and data bus
 ADQ0~ADQ15
 Asynchronous mode read access : 70ns
 Burst mode for Read and Write operation
 4, 8, 16 or Continuous
 Low Power Consumption
 Asynchronous Operation < 25 mA
 Burst operation < 45 mA (@133Mhz)
 Standby < 80 uA(max.)
 Deep power-down (DPD) < 3uA (Typ)
 Low Power Feature
 Reduced Array Refresh
 Temperature Controlled Refresh
 Operation Frequency up to 133MHz
 Operating temperature Range
Industrial -40°C~85°C
 Package: 54-ball VFBGA
Copyright © 2013 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its
products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services
described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information
and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or
effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to
its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Rev. A | July 2013
www.issi.com - [email protected]
1
IS66WVD1M16ALL
General Description
CellularRAM™ (Trademark of MicronTechnology) products are high
high-speed,
speed CMOS pseudo
pseudo-static
static
random access memories developed for low-power, portable applications.
The 16Mb DRAM core device is organized as 1 Meg x 16 bits. This device is a variation
of the industry-standard Flash control interface, with a multiplexed address/data bus.
The multiplexed address and data functionality dramatically reduce the required
signal count, and increase READ/WRITE bandwidth.
To operate seamlessly on a burst Flash bus, CellularRAM products have incorporated a
transparent self-refresh mechanism. The hidden refresh requires no additional support
from the system memory controller and has no significant impact on device read/write
performance.
Two user-accessible control registers define device operation. The bus configuration
register (BCR) defines how the CellularRAM device interacts with the system memory
bus and is nearly identical to its counterpart on burst mode Flash devices.
The refresh configuration register (RCR) is used to control how refresh is performed on
the DRAM array. These registers are automatically loaded with default settings during
power-up and can be updated anytime during normal operation.
Special attention has been focused on standby current consumption during self refresh.
CellularRAM products include three mechanisms to minimize standby current. Partial
array refresh (PAR) enables the system to limit refresh to only that part of the DRAM
array that contains essential data. Temperature-compensated refresh (TCR) uses an
on-chip sensor to adjust the refresh rate to match the device temperature — the refresh
rate decreases at lower temperatures to minimize current consumption during standby.
Deep power-down (DPD) enables the system to halt the refresh operation altogether
when no vital information is stored in the device. The system-configurable refresh
mechanisms are adjusted
j
through
g the RCR.
This CellularRAM device is compliant with the industry-standard CellularRAM 2.0
feature set established by the CellularRAM Workgroup. It includes support for both
variable and fixed latency, with three drive strengths, a variety of wrap options, and a
device ID register (DIDR).
A16~A19
Address
Decode Logic
Refresh
Configuration Register
(RCR)
1024K X 16
DRAM
Memory Array
Input
/Output
Mux
And
Buffers
Device ID Register
(DIDR)
Bus
Configuration Register
(BCR)
CE#
WE#
OE#
CLK
ADV#
CRE
LB#
UB#
WAIT
Controll
C
Logic
Rev. A | July 2013
ADQ0~ADQ15
[ Functional Block Diagram]
www.issi.com - [email protected]
2
IS66WVD1M16ALL
54B ll VFBGA B
54Ball
Ball
ll A
Assignment
i
t
1
2
3
4
5
6
A
LB#
OE#
NC
NC
NC
CRE
B
ADQ8
UB#
NC
NC
CE#
ADQ0
C
ADQ9
ADQ10
NC
NC
ADQ1
ADQ2
D
VSSQ
ADQ11
A17
NC
ADQ3
VDD
E
VDDQ
ADQ12
NC
A16
ADQ4
VSS
F
ADQ14
ADQ13
NC
NC
ADQ5
ADQ6
G
ADQ15
A19
NC
NC
WE#
ADQ7
H
A18
NC
NC
NC
NC
NC
J
WAIT
CLK
ADV#
NC
NC
NC
[Top View]
(Ball Down)
Rev. A | July 2013
www.issi.com - [email protected]
3
IS66WVD1M16ALL
Signal Descriptions
All signals for the device are listed below in Table 1.
Table 1. Signal Descriptions
Symbol
Type
VDD
Power Supply
Core Power supply (1.7V~1.95V)
VDDQ
Power Supply
I/O Power supply (1.7V~1.95V)
VSS
Power Supply
All VSS supply pins must be connected to Ground
VSSQ
Power Supply
All VSSQ supply pins must be connected to Ground
ADQ0~
ADQ15
Input / Output
Address Input(A0~A15)
Data Input/Output (DQ0~DQ15)
A16~A19
Input
Address Input(A16~A19)
LB#
Input
Lower Byte select
UB#
Input
Upper Byte select
CE#
Input
Chip Enable/Select
OE#
p
Input
Output
p Enable
WE#
Input
Write Enable
CRE
Input
Control Register Enable: When CRE is HIGH, READ and WRITE operations
access registers.
ADV#
Input
Address Valid signal
Signal that a valid address is present on the address bus. Address are
atc ed o
on tthe
e rising
s g edge o
of ADV# du
during
g asy
asynchronous
c o ous Read/Write
ead/ te
latched
operations. Addresses are latched on the rising edge of CLK with ADV#
low during synchronous operation.
CLK
Input
Clock
Latches addresses and commands on the first rising CLK edge when
ADV# is active in synchronous mode. CLK must be kept static Low during
asynchronous Read/Write operations.
WAIT
Output
WAIT
Data valid signal during burst Read/Write operation. WAIT is used to
arbitrate collisions between refresh and Read/Write operation. WAIT is
also asserted at the end of a row unless wrapping within the burst length.
WAIT is asserted and should be ignored during asynchronous READ
operation. WAIT is gated by CE# and is high-Z when CE# is high.
Rev. A | July 2013
Description
www.issi.com - [email protected]
4
IS66WVD1M16ALL
Functional Description
All functions for the device are listed below in Table 2.
Table 2. Functional Descriptions
Mode
Power
CLK1
ADV#
CE#
OE#
WE#
CRE2
UB#/
LB#
WAIT3
ADQ
[15:0]4
Note
Asynchronous Mode
Read
Active
L
L
L
H
L
L
Low-Z
Data-out
5
Write
Active
L
L
X
L
L
L
High-Z
Data-in
5
Standby
Stand
by
L
X
H
X
X
L
X
High-Z
High-Z
6,7
No Operation
Idle
L
X
L
X
X
L
X
Low-Z
X
5,7
Configuration
Register Write
Active
L
L
H
L
H
X
High-Z
High Z
High-Z
Configuration
Register Read
Active
L
L
L
H
H
L
Low-Z
Config-Reg
Out
Deep PowerDown
DPD
L
H
X
X
X
X
High-Z
High-Z
10
X
Synchronous Mode (Burst Mode)
Async read
Active
L
L
L
H
L
L
Low Z
Low-Z
Data Out
Data-Out
5
Async write
Active
L
L
X
L
L
L
High-Z
Data-In
5
Standby
Stand
by
L
X
H
X
X
L
X
High-Z
High-Z
6,7
No operation
Idle
L
X
L
X
X
L
X
Low-Z
X
5,8
Initial
burstt read
b
d
Active
L
L
X
H
L
L
Low-Z
Low
Z
Address
5,8
Initial
burst write
Active
L
L
H
L
L
X
Low-Z
Address
5,8
Burst
continue
Active
H
L
X
X
L
L
Low-Z
Data-In or
Data-Out
5,8
Burst suspend
Active
L
L
H
X
L
X
Low-Z
High-Z
5,8
Configuration
register write
Active
L
L
H
L
H
X
Low-Z
High-Z
8,11
Configuration
register read
Active
L
L
L
H
H
L
Low-Z
Config-Reg
Out
8,11
Deep PowerDown
DPD
X
H
X
X
X
X
High-Z
High-Z
10
Rev. A | July 2013
L
L
www.issi.com - [email protected]
5
IS66WVD1M16ALL
Notes
1. CLK must be LOW during Asynch Read and Asynch Write modes. CLK must be LOW to achieve
lo standby
low
standb ccurrent
ent d
during
ing standb
standby mode and DPD modes
modes. CLK m
must
st be static (LOW o
or HIGH)
during burst suspend.
2. Configuration registers are accessed when CRE is HIGH during the address portion
of a READ or WRITE cycle.
3. WAIT polarity is configured through the bus configuration register (BCR[10]).
4. When UB# and LB# are in select mode (LOW), ADQ0~ADQ15 are affected as shown.
When only LB# is in select mode, ADQ0~ADQ7 are affected as shown. When only UB# is
in select mode, ADQ8~ADQ15
ADQ8 ADQ15 are affected as shown.
5. The device will consume active power in this mode whenever addresses are changed with ADV#
LOW
6. When the device is in standby mode, address inputs and data inputs/outputs are internally
isolated from any external influence.
7. Vin=VDDQ or 0V, all device pins be static (unswitched) in order to achieve standby current.
8. Burst mode operation is initialized through the bus configuration register (BCR[15]).
9. Byte operation can be supported Write & Read at asynchronous mode and Write at
synchronous mode.
10. DPD is initiated when CE# transition from LOW to HIGH after writing RCR[4] to 0. DPD is
maintained until CE# transitions from HIGH to LOW
11. Initial cycle. Following cycles are the same as BURST CONTINUE. CE# must stay LOW
for the equivalent of a single word burst (as indicated by WAIT).
Rev. A | July 2013
www.issi.com - [email protected]
6
IS66WVD1M16ALL
Functional Description
In general, this device is high-density alternatives to SRAM and Pseudo SRAM products popular
in low-power, portable applications.
The 16Mb device contains a 16,777,216-bit DRAM core organized as 1,048,576 addresses by
16 bits. This device implements a multiplexed address/data bus.
This multiplexed configuration supports greater bandwidth through a x16 data bus, yet still
reduces the required signal count.
The CellularRAM bus interface supports both asynchronous and burst mode transfers.
Power-Up Initialization
CellularRAM products include an on-chip voltage sensor used to launch the power-up initialization
process. Initialization will configure the BCR and the RCR with their default settings (see Table 3
and Table 8). VDD and VDDQ must be applied simultaneously.
When they reach a stable level at or above 1.7V, the device will require 150μs to complete
its self-initialization process. During the initialization period, CE# should remain HIGH. When
initialization is complete,
complete the device is ready for normal operation.
operation
Figure 1: Power-Up Initialization Timing
VDD=1.7V
tPU > 150us
VDD
VDDQ
Rev. A | July 2013
Device Initialization
www.issi.com - [email protected]
Device ready for
normal operation
7
IS66WVD1M16ALL
Bus Operating Modes
CellularRAM products incorporate a burst mode interface targeted at low-power,
wireless applications. This bus interface supports asynchronous and burst mode read
and write transfers. The specific interface supported is defined by the value loaded into
the bus configuration register.
Burst Mode Operation
B t mode
Burst
d operations
ti
enable
bl high-speed
hi h
d synchronous
h
READ and
d WRITE operations.
ti
Burst operations consist of a multi-clock sequence that must be performed in an
ordered fashion.
The size of a burst can be specified in the BCR either as a fixed length or continuous.
Fixed-length bursts consist of four, eight, or sixteen words of sixteen bits. Continuous
bursts have the ability to start at a specified address and burst to the end of the row.
(Row length of 128 words or 256 words is a manufacturer option.)
The latency count stored in the BCR defines the number of clock cycles that elapse
before the initial data value is transferred between the processor and CellularRAM
device. The initial latency for READ operations can be configured as fixed or variable.
Variable latency allows the CellularRAM to be configured for minimum latency at high
clock frequencies, but the controller must monitor WAIT to detect any conflict with
refresh cycles (see Figure 23).
Fixed latency outputs the first data word after the worst-case access delay, including
allowance for refresh collisions. The initial latency time and clock speed determine the
latency count setting. Fixed latency is used when the controller cannot monitor WAIT.
Fixed latency also provides improved performance at lower clock frequencies
frequencies.
The WAIT output asserts when a burst is initiated and de-asserts to indicate when data
is to be transferred into (or out of) the memory. WAIT will again be asserted at the
boundary of the row unless wrapping within the burst length.
To access other devices on the same bus without the timing penalty of the initial latency
for a new burst, burst mode can be suspended. Bursts are suspended by stopping CLK.
CLK must be stopped LOW. If another device will use the data bus while the burst is
suspended, OE# should be taken HIGH to disable the CellularRAM outputs; otherwise,
OE# can remain LOW
LOW. Note that the WAIT output will continue to be active
active, and as a
result no other devices should directly share the WAIT connection to the controller. To
continue the burst sequence, OE# is taken LOW, then CLK is restarted after valid data is
available on the bus.
CE# LOW time is limited by refresh considerations. CE# must not stay LOW longer than
tCEM. If a burst suspension will cause CE# to remain LOW for longer than tCEM, CE#
should be taken HIGH and the burst restarted with a new CE# LOW/ADV# LOW cycle.
Rev. A | July 2013
www.issi.com - [email protected]
8
IS66WVD1M16ALL
Burst Read Operation
After CE# goes LOW, the address to access is latched on the rising edge of the next clock
that ADV# is LOW. During this first clock rising edge, WE# indicates whether the operation
is going to be a READ (WE# = HIGH, Figure 2)
Then the data needs to be output to multiplexed data bus (ADQ0~ADQ15)
according to set WAIT states.
The WAIT output asserts when a burst is initiated, and de-asserts to indicate when data
is to be transferred into (or out of ) the memory. WAIT will again be asserted at the
boundary of a row, unless wrapping within the burst length.
A full
f ll 4 word
d synchronous
h
read
d access is
i shown
h
in
i Figure
Fi
2 and
d the
th AC characteristics
h
t i ti are specified
ifi d
in Table 16.
Figure 2. Synchronous Read Access Timing
tCLK
tABA
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tACLK
tHD
VALID
ADDRESS
tSP
ADV#
tKOH
VALID
OUTPUT
VALID
OUTPUT
tHZ
tHD
tSP
tHD
tHD
WE#
tOLZ
tOHZ
tOE
OE#
tWZ
tKW
WAIT
tCBPH
tCEM
CE#
tSP
VALID
OUTPUT
tHD
tCSP
UB#/LB#
VALID
OUTPUT
tKW
HiZ
Read Burst Identified (WE#=HIGH)
Rev. A | July 2013
www.issi.com - [email protected]
9
IS66WVD1M16ALL
Burst Write Operation
After CE# goes LOW, the address to access is latched on the rising edge of the next clock
that ADV# is LOW. During this first clock rising edge, WE# indicates whether the operation
is going to be a WRITE (WE# =LOW, Figure 3).
Data is placed to the multiplexed data bus (ADQ0~ADQ15) with consecutive clock cycles
when WAIT de-asserts.
The WAIT output asserts when a burst is initiated, and de-asserts to indicate when data
is to be transferred into (or out of ) the memory. WAIT will again be asserted at the
boundary of a row, unless wrapping within the burst length.
A full
f ll 4 word
d synchronous
h
write
it access is
i shown
h
in
i Figure
Fi
3 and
d the
th AC characteristics
h
t i ti are
specified in Table 18.
Figure 3. Synchronous Write Access Timing
tCLK
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tSP
tHD
VALID
ADDRESS
tHD
DATA IN
DATA IN
DATA IN
DATA IN
tAS
tAS
ADV#
tHD
tCSP
tCEM
CE#
tCBPH
tSP
UB#/LB#
tSP
WE#
tHD
tHD
tHD
tKW
WAIT
tKW
HiZ
Write Burst Identified (WE#=LOW)
Rev. A | July 2013
www.issi.com - [email protected]
10
IS66WVD1M16ALL
Asynchronous Mode
Asynchronous mode uses industry-standard SRAM control signals (CE#, ADV#, OE#,
WE#, UB#, and LB#). READ operations (Figure 4) are initiated by bringing CE#, ADV#,
UB# and LB# LOW while keeping OE# and WE# HIGH, and driving the address onto the
multiplexed address/data bus. ADV# is taken HIGH to capture the address, and OE# is
taken LOW. Valid data will be driven out of the I/Os after the specified access time has
elapsed.
WRITE operations (Figure 5) occur when CE#, ADV#, WE#, UB#, and LB# are driven LOW
with the address on the multiplexed address/data bus. ADV# is taken HIGH to capture
th address,
the
dd
then
th the
th write
it data
d t is
i driven
di
onto
t the
th bus.
b
During
D i asynchronous
h
WRITE
operations, the OE# level is a “Don't Care,” and WE# will override OE#; however, OE#
must be HIGH while the address is driven onto the ADQ bus. The data to be written is
latched on the rising edge of CE#, WE#, UB#, and LB# (whichever occurs first).
During asynchronous operation, the CLK input must be held LOW. WAIT will be driven
during asynchronous READs, and its state should be ignored. WE# must not be held
LOW longer than tCEM.
Figure 4. Asynchronous Read Access Timing
tAA
VALID
ADDRESS
Address
tAVS
ADQ0
ADQ0ADQ15
tAVH
VALID
ADDRESS
VALID
OUTPUT
tAADV
tVP
ADV#
tCVP
CE#
tWZ
tCO
tHZ
tBHZ
tBA
UB#/LB#
tOLZ
tOE
OE#
WE#
WAIT
Rev. A | July 2013
tOHZ
tOEW
HiZ
HiZ
www.issi.com - [email protected]
11
IS66WVD1M16ALL
Figure
g
5. Asynchronous
y
Write Access Timing
g
tAW
tAS
Address
VALID
ADDRESS
tAVS
ADQ0ADQ15
tAVH
tDS
VALID
ADDRESS
tDH
VALID
DATA
tVS
tVP
ADV#
tCVP
CE#
tWP
WE#
Rev. A | July 2013
tCW
tBW
UB#/LB#
WAIT3#
tAS
HiZ
HiZ
www.issi.com - [email protected]
12
IS66WVD1M16ALL
Mixed-Mode Operation
The device can support a combination of synchronous READ and asynchronous READ
and WRITE operations when the BCR is configured for synchronous operation. The
asynchronous READ and WRITE operations require that the clock (CLK) remain LOW
during the entire sequence. The ADV# latches the target address. CE# can remain LOW
when transitioning between mixed-mode operations with fixed latency enabled;
however, the CE# LOW time must not exceed tCEM. Mixed-mode operation facilitates a
seamless interface to legacy burst mode Flash memory controllers. See Figure 33 for the
“Asynchronous WRITE Followed by Burst READ” timing diagram.
WAIT Operation
WAIT output on the CellularRAM device is typically connected to a shared, system-level
WAIT signal. The shared WAIT signal is used by the processor to coordinate transactions
with multiple memories on the synchronous bus.
When a synchronous READ or WRITE operation has been initiated, WAIT goes active to
indicate that the CellularRAM device requires additional time before data can be
transferred. For READ operations, WAIT will remain active until valid data is output
from the device. For WRITE operations, WAIT will indicate to the memory controller
when data will be accepted into the CellularRAM device. When WAIT transitions to an
inactive state, the data burst will progress on successive rising clock edges.
During a burst cycle CE# must remain asserted until the first data is valid. Bringing CE#
HIGH during this initial latency may cause data corruption.
When using variable initial access latency (BCR[14] = 0), the WAIT output performs an
arbitration role for READ operations launched while an on-chip refresh is in progress.
progress If
a collision occurs, the WAIT pin is asserted for additional clock cycles until the refresh
has completed (see Figure 23). When the refresh operation has completed, the
READ operation will continue normally.
WAIT will be asserted but should be ignored during asynchronous READ operations.
WAIT will be High-Z during asynchronous WRITE operations.
By using fixed initial latency (BCR[14] = 1), this CellularRAM device can be used in burst
mode without monitoring the WAIT pin. However, WAIT can still be used to determine
when valid data is available at the start of the burst and at the end of the row
row. If wait is
not monitored, the controller must stop burst accesses at row boundaries on its own.
UB#/LB# Operation
The UB#/LB# enable signals support byte-wide data WRITEs. During WRITE operations,
any disabled bytes will not be transferred to the RAM array and the internal value will
remain unchanged. During an asynchronous WRITE cycle, the data to be written is
latched on the rising edge of CE#, WE#, UB#, and LB# whichever occurs first.
UB#/LB# must be LOW during READ cycles.
When UB#/LB# are disabled (HIGH) during an operation, the device will disable the data
bus from receiving or transmitting data. Although the device will seem to be deselected,
it remains in an active mode as long as CE# remains LOW.
Rev. A | July 2013
www.issi.com - [email protected]
13
IS66WVD1M16ALL
Low-Power Feature
Standby Mode Operation
During standby, the device current consumption is reduced to the level necessary to
perform the DRAM refresh operation. Standby operation occurs when CE# is HIGH.
The device will enter a reduced power state upon completion of a READ or WRITE
operation, or when the address and control inputs remain static for an extended period
of time. This mode will continue until a change occurs to the address or control inputs.
Temperature-Compensated Refresh
Temperature-compensated refresh (TCR) allows for adequate refresh at different
temperatures. This CellularRAM device includes an on-chip temperature sensor that
automatically adjusts the refresh rate according to the operating temperature. The
device continually adjusts the refresh rate to match that temperature.
Partial-Array Refresh
Partial-array refresh (PAR) restricts refresh operation to a portion of the total memory
array. This feature enables the device to reduce standby current by refreshing only that
part of the memory array required by the host system. The refresh options are full array,
one-half array, one-quarter array, one-eighth array, or none of the array. The mapping
of these partitions can start at either the beginning or the end of the address map (see
Table 9 ). READ and WRITE operations to address ranges receiving refresh will not be affected.
Data stored in addresses not receiving refresh will become corrupted. When re-enabling additional
portions of the array, the new portions are available immediately upon writing to the RCR.
Deep Power-Down Operation
Deep power-down (DPD) operation disables all refresh-related activity. This mode is
used
d if the
th system
t
does
d
nott require
i the
th storage
t
provided
id d by
b the
th CellularRAM
C ll l RAM device.
d i
Any
A
stored data will become corrupted when DPD is enabled. When refresh activity has been
re-enabled, the CellularRAM device will require 150μs to perform an initialization
procedure before normal operations can resume. During this 150μs period, the current
consumption will be higher than the specified standby levels, but considerably lower
than the active current specification.
DPD can be enabled by writing to the RCR using CRE or the software access sequence;
DPD starts when CE# goes HIGH. DPD is disabled the next time CE# goes LOW.
Rev. A | July 2013
www.issi.com - [email protected]
14
IS66WVD1M16ALL
Registers
Two user-accessible configuration registers define the device operation. The bus
configuration register (BCR) defines how the CellularRAM interacts with the system
memory bus and is nearly identical to its counterpart on burst mode Flash devices. The
refresh configuration register (RCR) is used to control how refresh is performed on the
DRAM array. These registers are automatically loaded with default settings during
power-up, and can be updated any time the devices are operating in a standby state.
A DIDR provides information on the device manufacturer, CellularRAM generation, and
the specific device configuration. The DIDR is read-only.
Access Using CRE
The registers can be accessed using either a synchronous or an asynchronous operation
when the configuration register enable (CRE) input is HIGH (see Figures 6 through 9).
When CRE is LOW, a READ or WRITE operation will access the memory array. The register
values are written as an address (ADV# LOW) on the ADQ pins.
In an asynchronous WRITE,
WRITE the values are latched into the configuration register
on the rising edge of CE# or WE#, whichever occurs first; UB#/LB# are “Don’t Care.”
The BCR is accessed when A[19:18] is 10b; the RCR is accessed when A[19:18] is 00b; the
DIDR is accessed when A[19:18] is 01b. For READs, address inputs other than A[19:18]
are “Don’t Care,” and register bits are output as data (ADV# HIGH) on ADQ.
Figure 6: Configuration Register WRITE
– Asynchronous Mode Followed by READ ARRAY Operation
Address
VALID
ADDRESS
OPCODE
tAVS tAVH
ADQ0ADQ151
tAVS tAVH
VALID
ADDRESS
OPCODE
tVS
tAADV
tVP
ADV#
VALID
OUTPUT
tVP
tCVP
tCPP
tCW
CE#
tCPH
tHZ
tCO
tBA
UB#/LB#
/
tWP
WE#
Write Address Bus
Value to Control
Register
OE#
tAVS
tOLZ
tOE
tAVH
CRE2
Notes:
1. A[19:18] = 00b to load RCR ADQ[15:0]; 10b to load BCR ADQ[15:0].
2. CRE must be HIGH to access registers.
Rev. A | July 2013
www.issi.com - [email protected]
15
IS66WVD1M16ALL
Figure 7: Configuration Register WRITE
– Synchronous Mode Followed by READ ARRAY Operation
tCLK
tABA
CLK
Address
VALID
ADDRESS
OPCODE
tSP tHD
tSP tHD
ADQ0ADQ15
tACLK
VALID
ADDRESS
OPCODE
tKOH
VALID VALID VALID VALID
OUTPUTOUTPUTOUTPUTOUTPUT
tAS
tAS
ADV#
tCBPH3
tCSP
tCEM
tCEM
CE#
tHD
UB#/LB#
tSP tHD
WE#
tOHZ
tOE
OE#
tKW
WAIT
tKW
HiZ
tWZ
tKW
tKW
tHD
CRE4
tSP
Notes:
1. Non-default BCR settings for configuration register WRITE in synchronous mode, followed by READ ARRAY
operation: Latency code three (four clocks); WAIT active LOW; WAIT asserted during delay.
2 A[19:18]
2.
A[19 18] = 00b to
t load
l d RCR ADQ[15:0];
ADQ[15 0] 10b to
t load
l d BCR ADQ[15:0].
ADQ[15 0]
3. CE# must remain LOW to complete a burst-of-one WRITE. WAIT must be monitored additional WAIT
cycles caused by refresh collisions require a corresponding number of additional CE# LOW cycles.
4. CRE must be HIGH to access registers.
Rev. A | July 2013
www.issi.com - [email protected]
16
IS66WVD1M16ALL
Figure 8: Configuration Register READ
– Asynchronous Mode Followed by DATA READ
tAA
Select
Control
Register
Address
VALID
ADDRESS
tAVS tAVH
ADQ0ADQ151
tAVS tAVH
VALID
ADDRESS
CR Valid
Don’t Care
tAADV
tAADV
tVP
ADV#
VALID
OUTPUT
tVP
tCPP
tCO
CE#
tCPH
tHZ
tCO
tBA
UB#/LB#
/
WE#
tOLZ
tOE
OE#
tAVS
tOE
tAVH
CRE2
Notes:
1. A[19:18] = 00b to load RCR ADQ[15:0]; 10b to load BCR ADQ[15:0]; 01b to load DIDR ADQ[15:0].
2. CRE must be HIGH to access registers.
Rev. A | July 2013
www.issi.com - [email protected]
17
IS66WVD1M16ALL
Figure 9: Configuration Register READ
– Synchronous Mode Followed by Data READ
tCLK
tABA
CLK
Select
Control
Register
Address
VALID
ADDRESS
tACLK
tSP tHD
ADQ0ADQ15
tKOH
CR
valid
Don’t
Care
tSP tHD
tACLK
VALID
ADDRESS
tKOH
VALID VALID VALID VALID
OUTPUTOUTPUTOUTPUTOUTPUT
tAS
tAS
ADV#
tCBPH3
tCSP
tCEM
tABA
CE#
tHD
UB#/LB#
tSP tHD
WE#
tOHZ
tOE
OE#
tKW
WAIT
tKW
HiZ
tWZ
tKW
tKW
tHD
CRE4
tSP
Notes:
1. Non-default BCR settings for configuration register READ in synchronous mode, followed by READ ARRAY
operation: Latency code two (three clocks); WAIT active LOW; WAIT asserted during delay.
2 A[19:18]
2.
A[19 18] = 00b to
t load
l d RCR ADQ[15:0];
ADQ[15 0] 10b to
t load
l d BCR ADQ[15:0];
ADQ[15 0] 01b to
t load
l d DIDR ADQ[15:0].
ADQ[15 0]
3. CE# must remain LOW to complete a burst-of-one READ. WAIT must be monitored additional WAIT
cycles caused by refresh collisions require a corresponding number of additional CE# LOW cycles.
4. CRE must be HIGH to access registers.
Rev. A | July 2013
www.issi.com - [email protected]
18
IS66WVD1M16ALL
Software Access Sequence
Software access of the configuration registers uses a sequence of asynchronous READ
and asynchronous WRITE operations. The contents of the configuration registers can be
read or modified using the software sequence.
The configuration registers are loaded using a four-step sequence consisting of two
asynchronous READ operations followed by two asynchronous WRITE operations (see
Figure 11). The read sequence is virtually identical except that an asynchronous READ is
performed during the fourth operation (see Figure 10). The address used during all
READ and WRITE operations is the highest address of the CellularRAM device being
accessed
d (FFFFFh);
(FFFFFh) th
the contents
t t off thi
this address
dd
are nott changed
h
db
by using
i thi
this sequence.
The data value presented during the third operation (WRITE) in the sequence
defines whether the BCR or the RCR is to be accessed. If the data is 0000h, the sequence
will access the RCR; if the data is 0001h, the sequence will access the BCR;
if the data is 0002h, the sequence will access the DIDR. During the fourth operation,
ADQ[15:0] transfer data into or out of bits 15:0 of the control registers.
The use of the software sequence does not affect the ability to perform the standard
(CRE-controlled) method of loading the configuration registers. However, the software
nature of this access mechanism eliminates the need for the control register enable
(CRE) pin. If the software mechanism is used, the CRE pin can simply be tied to VSS.
The port line often used for CRE control purposes is no longer required.
Figure 10 : Configuration Register Read
Address
MAX
ADDRESS
ADQ0ADQ15
MAX
ADDRESS
MAX
ADDRESS
OUTPUT
DATA
MAX
ADDRESS
MAX
ADDRESS
OUTPUT
DATA
MAX
ADDRESS
MAX
ADDRESS
*Note1
MAX
ADDRESS
CR
VALUE OUT
ADV#
CE#
Read
Read
Write
Read
UB#/LB#
WE#
OE#
Notes :
1. RCR : 0000h , BCR : 0001h , DIDR : 0002h
Rev. A | July 2013
www.issi.com - [email protected]
19
IS66WVD1M16ALL
Figure 11 : Configuration Register Write
Address
ADQ0ADQ15
MAX
ADDRESS
MAX
ADDRESS
MAX
ADDRESS
OUTPUT
DATA
MAX
ADDRESS
MAX
ADDRESS
OUTPUT
DATA
MAX
ADDRESS
MAX
ADDRESS
*Note1
MAX
ADDRESS
CR
VALUE IN
ADV#
CE#
Read
Read
Write
Write
UB#/LB#
WE#
OE#
N t :
Notes
1. RCR : 0000h , BCR : 0001h
Rev. A | July 2013
www.issi.com - [email protected]
20
IS66WVD1M16ALL
Bus Configuration Register
The BCR defines how the CellularRAM device interacts with the system memory bus.
Table 3 describes the control bits in the BCR. At power-up, the BCR is set to 1D1Fh.
The BCR is accessed using CRE and A[19:18] = 10b, or through the configuration
register software sequence with ADQ[15:0] = 0001h on the third cycle.
Table 3. Bus configuration Register
Remark
Bit Number
Definition
19 – 18
Register Select
00 = Select RCR
01 = Select DIDR
10 = Select BCR
17 – 16
Reserved
Must be set to “0”
15
Operating mode
14
Initial Latency
0 = Variable (default)
1 = Fixed
13 – 11
Latency Count
000 =
001 =
010 =
011 =
100 =
101 =
110 =
111 =
10
WAIT Polarity
0 = Active LOW : Data valid at WAIT HIGH
1 = Active HIGH : Data valid at WAIT LOW (default)
9
Reserved
8
WAIT Configuration
7–6
Reserved
9 clock cycles
reserved
3 clock cycles
4 clock cycles (default)
5 clock cycles
6 clock cycles
7 clock cycles
reserved
Must be set to “0”
0 = Asserted during delay
1 = Asserted one data cycle before delay (default)
Must be set to “0”
00
01
10
11
=
=
=
=
Full drive
½ Drive (default)
¼ Drive
Reserved
5–4
Output Impedance
3
Burst mode
0 = Burst wrap
p within the burst length
g
1 = Burst no wrap (default)
Burst Length
001 = 4 words
010 = 8 words
011 = 16 words
111 = continuous (default)
Others = Reserved
2–0
Notes :
0 = Synchronous burst access mode (default)
1 = Asynchronous
A
h
access mode
d
1.Burst wrap and length apply to both READ and WRITE operations.
Rev. A | July 2013
www.issi.com - [email protected]
21
IS66WVD1M16ALL
Burst Length (BCR[2:0]) Default = Continuous Burst
Burst lengths define the number of words the device outputs during burst READ and
WRITE operations. The device supports a burst length of four, eight, or sixteen words of
sixteen bits. The device can also be set in continuous burst mode where data is
accessed sequentially up to the end of the row.
Burst Wrap (BCR[3]) Default = No Wrap
Th burst-wrap
The
b t
option
ti determines
d t
i
if a 4-,
4 8-,
8 or 16-word
16
d READ or WRITE burst
b t wraps
within the burst length, or steps through sequential addresses if continuous burst
operation is selected in BCR[2:0]. If the wrap option is not enabled, the device accesses
data from sequential addresses up to the end of the row.
Table 4. Sequence and Burst Length
Starting
Address
Wrap
BL4
BL8
BL16
Continuous
DEC
BCR[3]
Linear
Linear
Linear
Linear
0
0-1-2-3
0-1-2-3-4-5-6-7
0-1-2-3- ••• -12-13-14-15
0-1-2-3-4-5-6- •••
1
1-2-3-0
1-2-3-4-5-6-7-0
1-2-3-4- ••• -13-14-15-0
1-2-3-4-5-6-7- •••
2
2-3-0-1
2-3-4-5-6-7-0-1
2-3-4-5- ••• -14-15-0-1
2-3-4-5-6-7-8- •••
3
3-0-1-2
3-4-5-6-7-0-1-2
3-4-5-6- ••• -15-0-1-2
3-4-5-6-7-8-9- •••
•••
•••
•••
•••
•••
6
6-7-4-5
6-7-0-1-2-3-4-5
6-7-8-9- ••• -2-3-4-5
6-7-8-9-10-11-12- •••
7-4-5-6
7-0-1-2-3-4-5-6
7-8-9-10- ••• -3-4-5-6
7-8-9-10-11-12-13- •••
7
“0”
Wrap
•••
•••
•••
•••
•••
14
14-15-12-13
14-15-8-9-10-11-12-13
14-15-0-1- ••• -10-11-12-13
14-15-16-17-18-19-20- •••
15
15-12-13-14
15-8-9-10-11-12-13-14
15-0-1-2-3- ••• -11-13-13-14
15-16-17-18-19-20-21- •••
•••
•••
•••
•••
•••
254
254-255-252-253
254-255-248-249-250-251-252-253
254-255-240-241- ••• -250-251-252-253
254-255-0-1-2-•••
255
255-252-253-254
255-248-249-250-251-252-253-254
255-240-241-242- ••• -251-252-253-254
255-0-1-2-•••
0
0-1-2-3
0-1-2-3-4-5-6-7
0-1-2-3-4- ••• -12-13-14-15
0-1-2-3-4-5-6- •••
1
1-2-3-4
1-2-3-4-5-6-7-8
1-2-3-4- ••• -13-14-15-16
1-2-3-4-5-6-7- •••
2
2-3-4-5
2-3-4-5-6-7-8-9
2-3-4-5- ••• -14-15-16-17
2-3-4-5-6-7-8- •••
3
3-4-5-6
3-4-5-6-7-8-9-10
3-4-5-6- ••• -15-16-17-18
3-4-5-6-7-8-9- •••
•••
•••
•••
•••
•••
6-7-8-9
6-7-8-9-10-11-12-13
6-7-8-9- ••• -18-19-20-21
6-7-8-9-10-11-12- •••
6
7
“1”
No Wrap
7-8-9-10
7-8-9-10-11-12-13-14
7-8-9-10- ••• -19-20-21-22
7-8-9-10-11-12-13- •••
•••
•••
•••
•••
•••
14
14-15-16-17
14-15-16-17-18-19-20-21
14-15-16-17- ••• - 26-27-28-29
14-15-16-17-18-19-20- •••
15
15-16-17-18
15-16-17-18-19-20-21-22
15-16-17-18- ••• -27-28-29-30
15-16-17-18-19-20-21- •••
•••
•••
•••
•••
•••
254
254-255
254-255
254-255
254-255
255
255
255
255
255
Rev. A | July 2013
www.issi.com - [email protected]
22
IS66WVD1M16ALL
Drive Strength (BCR[5:4]) Default = Outputs Use Half-Drive Strength
The output driver strength can be altered to full, one-half, or one-quarter strength to
adjust for different data bus loading scenarios. The reduced-strength options are intended
for stacked chip (Flash + CellularRAM) environments when there is a dedicated memory
bus. The reduced-drive-strength option minimizes the noise generated on the data bus
during READ operations. Full output drive strength should be selected when using a
discrete CellularRAM device in a more heavily loaded data bus environment. Outputs are
configured at half-drive strength during testing. See Table 5.
Table 5. Drive Strength
BCR[5]
BCR[4]
Drive Strength
Impedance Typ (Ω)
Use Recommendation
0
0
Full
25 ~ 30
CL = 30pF to 50pF
0
1
1/2(Default)
50
CL = 15pF to 30pF
104MHz
0
at light
g t load
oad
1
0
1/4
100
CL = 15pF or lower
1
1
Reserved
WAIT Configuration (BCR[8]) Default = WAIT Transitions One Clock Before Data Valid/Invalid
The WAIT configuration bit is used to determine when WAIT transitions between the
asserted and the de-asserted state with respect to valid data presented on the data bus.
The memory controller will use the WAIT signal to coordinate data transfer during
synchronous READ and WRITE operations. When BCR[8] = 0, data will be valid or invalid
on the clock edge immediately after WAIT transitions to the de-asserted or asserted state
respectively. When BCR[8] = 1, the WAIT signal transitions one clock period prior to the data
bus going valid or invalid (see Figure 12).
Figure 12. WAIT Configuration During Burst Operation
CLK
ADQ0ADQ15
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
WAIT
BCR[8]=0
Data valid/invalid in current cycle
WAIT
BCR[8]=1
Data valid/invalid in next cycle
Notes :
Non-default BCR setting : WAIT active LOW
WAIT P
Polarity
l it (BCR[10]) D
Default
f lt = WAIT A
Active
ti HIGH
The WAIT polarity bit indicates whether an asserted WAIT output should be HIGH or
LOW. This bit will determine whether the WAIT signal requires a pull-up or pull-down
resistor to maintain the de-asserted state.
Rev. A | July 2013
www.issi.com - [email protected]
23
IS66WVD1M16ALL
Latency Counter (BCR[13:11]) Default = Three Clock Latency
The latency counter bits determine how many clocks occur between the beginning of a
READ or WRITE operation and the first data value transferred. Latency codes from two
(three clocks) to six (seven clocks) and eight (nine clocks) are supported (see Tables 6
and 7, Figure 13, and Figure 14).
Initial Access Latency (BCR[14]) Default = Variable
V i bl initial
Variable
i iti l access latency
l t
outputs
t t data
d t after
ft the
th number
b off clocks
l k sett by
b the
th latency
l t
counter. However, WAIT must be monitored to detect delays caused by collisions with
refresh operations.
Fixed initial access latency outputs the first data at a consistent time that allows for
worst-case refresh collisions. The latency counter must be configured to match the
initial latency and the clock frequency. It is not necessary to monitor WAIT with fixed
initial latency. The burst begins after the number of clock cycles configured by the
latency counter. (See Table 6 and Figure 13)
Table 6. Variable Latency Configuration Codes (BCR[14] = 0)
Latency
Latency
Configuration
Code
BCR
[13:11]
Max Input CLK Frequency (MHz)
Normal
Refresh
Collision
-75
-96
-12
66 (15.0ns)
52 (18.5ns)
104 (9.62ns)
80 (12.5ns)
-
-
010
2 (3 clocks)
2
4
66 (15.0ns)
011
3 (4 clocks)-default
3
6
104 (9.62ns)
100
4 (5 clocks)
4
8
133 (7.5ns)
Reserved
-
-
-
others
N t
Notes:
1. Latency is the number of clock cycles from the initialization of a burst operation until data appears.
Data is transferred on the next clock cycle. READ latency can range from the normal latency to the value
shown for refresh collision.
Figure 13. Latency Counter (Variable Latency, No Refresh Collision)
CLK
ADV#
Code 2 (3 clocks)
ADQ0ADQ15
VALID
ADDRESS
ADQ0ADQ15
VALID
ADDRESS
ADQ0ADQ15
VALID
ADDRESS
Rev. A | July 2013
Code 3 (4 clocks) : Default
Code 4 (5 clocks)
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
www.issi.com - [email protected]
24
IS66WVD1M16ALL
Table 7. Fixed Latency Configuration Codes (BCR[14] = 1)
Latency
Configuration
Code
BCR
[13:11]
Latency
Count (N)
Max Input CLK Frequency (MHz)
-75
-96
-12
010
2 (3 clocks)
2
33 (30ns)
33 (30ns)
25 (40ns)
011
3 (4 clocks)-default
3
52 (19.2ns)
52 (19.2ns)
40 (25ns)
100
4 (5 clocks)
4
66 (15ns)
66 (15.0ns)
52 (19.2ns)
101
5 (6 clocks)
5
75 (13.3ns)
75 (13.3ns)
66 (15.0ns)
110
6 (7 clocks)
6
104 (9.62ns)
104 (9.62ns)
80 (12.5ns)
000
8 (9 clocks)
8
133 (7.5ns)
-
-
Reserved
-
-
-
-
others
Figure 14. Latency Counter (Fixed Latency)
CLK
ADV#
tAADV
CE#
tCO
tAA
ADQ0ADQ15
(READ)
VALID
ADDRESS
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
ADQ0ADQ15
(WRITE)
VALID
ADDRESS
VALID
INPUT
VALID
INPUT
VALID
INPUT
Burst Identified
(ADV#=LOW)
Operating Mode (BCR[15]) Default = Synchronous Operation
The operating mode bit enables synchronous burst operation or limits the device to the
asynchronous mode of operation only. If the clock is stopped LOW, all accesses are
asynchronous, even when synchronous mode is enabled.
Rev. A | July 2013
www.issi.com - [email protected]
25
IS66WVD1M16ALL
Refresh Configuration Register
The refresh configuration register (RCR) defines how the CellularRAM device performs
its transparent self refresh. Altering the refresh parameters can dramatically reduce
current consumption during standby mode. Table 8 describes the control bits used in
the RCR.
The RCR is accessed using CRE and A[19:18] = 00b, or through the configuration
register software access sequence with ADQ = 0000h on the third cycle (see “Registers”)
Table 8. Refresh Configuration Register
Bit Number
Definition
19 – 18
Register Select
00 = Select RCR
01 = Select DIDR
10 = Select BCR
17 – 7
Reserved
Must be set to “0”
0
6–5
Reserved
Setting is ignored
4
DPD
3
Reserved
2–0
Rev. A | July 2013
Partial Refresh
Remark
0 = DPD enable
1 = DPD disable (default)
Must be set to “0”
000 =
001 =
010 =
011 =
100 =
101 =
110 =
111 =
Full array (default)
Bottom 1/2 array
Bottom 1/4 array
Bottom 1/8 array
None of array
Top 1/2 array
Top 1/4 array
Top 1/8 array
www.issi.com - [email protected]
26
IS66WVD1M16ALL
Partial-Array Refresh (RCR[2:0]) Default = Full Array Refresh
The PAR bits restrict refresh operation to a portion of the total memory array. This
feature allows the device to reduce standby current by refreshing only that part of the
memory array required by the host system. The refresh options are full array, one-half
array, one-quarter array, one-eighth array, or none of the array. The mapping of these
partitions can start at either the beginning or the end of the address map (see Tables 9)
Table 9. 16Mb Address Patterns for PAR (RCR[4]=1)
RCR[2]
RCR[1]
RCR[0]
Active Section
Address Space
Size
Density
0
0
0
Full
000000h ~ 0FFFFFh
1MX16
16Mb
0
0
1
Bottom 1/2 array
000000h ~ 07FFFFh
512KX16
8Mb
0
1
0
Bottom 1/4 array
000000h ~ 03FFFFh
256KX16
4Mb
0
1
1
Bottom 1/8 array
000000h ~ 01FFFFh
128KX16
2Mb
1
0
0
None of array
0
1
0
1
Top 1/2 array
80000h ~ 0FFFFFh
512KX16
8Mb
1
1
0
Top 1/4 array
C0000h ~ 0FFFFFh
256KX16
4Mb
1
1
1
Top 1/8 array
E0000h ~ 0FFFFFh
128KX16
2Mb
0Mb
Deep Power-Down (RCR[4]) Default = DPD Disabled
The deep power
power-down
down bit enables and disables all refresh-related
refresh related activity
activity. This mode is
used if the system does not require the storage provided by the CellularRAM device. Any
stored data will become corrupted when DPD is enabled. When refresh activity has been
re-enabled, the CellularRAM device will require 150μs to perform an initialization
procedure before normal operations can resume.
Deep power-down is enabled by setting RCR[4] = 0 and taking CE# HIGH. Taking CE# LOW
disables DPD and sets RCR[4] = 1; it is not necessary to write to the RCR to disable DPD. DPD
can be enabled using CRE or the software sequence to access the RCR. BCR and RCR
values (other than BCR[4]) are preserved during DPD.
DPD
Device Identification Register
The DIDR provides information on the device manufacturer, CellularRAM generation,
and the specific device configuration. Table 10 describes the bit fields in the DIDR. This
register is read-only.
The DIDR is accessed with CRE HIGH and A[19:18] = 01b, or through the software access
sequence with ADQ = 0002h on the third cycle.
Table 10. Device Identification Register Mapping
Bit Field
DIDR[15]
DIDR[14:11]
DIDR[10:8]
DIDR[7:5]
DIDR[4:0]
Field Name
Row Length
Device Version
Device Density
CellularRAM
Generation
Vendor ID
Length
- words
Bit
Setting
V i
Version
Bit
Setting
D
Density
it
Bit
Setting
Genera
tion
Bit
Setting
V d
Vendor
Bit
Setting
128
0b
1st
0000b
16Mb
000b
CR1.5
010b
ISSI
00101b
256
1b
2nd
0001b
32Mb
001b
CR2.0
011b
Rev. A | July 2013
www.issi.com - [email protected]
27
IS66WVD1M16ALL
Electrical Characteristics
Table 11. Absolute Maximum Ratings
Parameter
Rating
Voltage to Any Ball Except VDD, VDDQ Relative to VSS
-0.3V to VDDQ + 0.3V
Voltage on VDD Supply Relative to VSS
-0.2V to + 2.45V
Voltage on VDDQ Supply Relative to VSS
-0.2V to + 2.45V
Storage
g Temperature
p
(plastic)
(p
)
-55°Cto + 150°C
Operating Temperature (case)
-40°Cto + 85°C
Soldering Temperature and Time : 10s (solder ball only)
+ 260°C
Notes:
Stresses greater than those listed may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at these or any other
conditions above those indicated in this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect reliability
reliability.
Table 12. Electrical Characteristics and Operating Conditions
Industrial Temperature (–40ºC < TC < +85ºC)
Description
Conditions
MIN
MAX
Unit
VDD
1.7
1.95
V
I/O Supply Voltage
VDDQ
1.7
1.95
V
Input High Voltage
VIH
VDDQ-0.4
VDDQ+0.2
V
1
Input Low Voltage
VIL
-0.20
0.4
V
2
0.80 VDDQ
V
3
3
Supply Voltage
Symbol
Note
Output High Voltage
IOH = -0.2mA
VOH
Output Low Voltage
IOL = +0.2mA
VOL
0.20 VDDQ
V
VIN = 0 to VDDQ
ILI
1
uA
Output Leakage Current
OE#=VIH or
Chip Disabled
ILO
1
uA
Operating Current
Conditions
MAX
Unit
Note
-70
25
mA
4
133Mhz
45
104Mhz
35
mA
4
80Mhz
30
133Mhz
40
104Mhz
30
mA
4
80Mhz
25
133Mhz
40
104Mhz
35
mA
4
80Mhz
30
uA
5
Input Leakage Current
Asynchronous Random
READ/WRITE
IDD1
Initial Access,
Access Burst
READ/WRITE
Continuous Burst READ
IDD2
VIN = VDDQ or 0V
Chip enabled,
IOUT = 0
Continuous Burst WRITE
Standby Current
Rev. A | July 2013
Symbol
IDD3R
IDD3W
VIN=VDDQ or 0V
CE#=VDDQ
ISB
www.issi.com - [email protected]
TYP
80
28
IS66WVD1M16ALL
Notes:
1.
2
2.
3.
4.
Input signals may overshoot to VDDQ + 1.0V for periods less than 2ns during transitions.
Input
I
signals
i
l may undershoot
d h
to Vss
V – 1.0V
1 0V for
f periods
i d less
l
than
h 2ns
2 during
d i transitions.
ii
BCR[5:4] = 01b (default setting of one-half drive strength).
This parameter is specified with the outputs disabled to avoid external loading effects.
User must add required current to drive output capacitance expected in the actual system.
5. ISB (MAX) values measured with PAR set to FULL ARRAY at +85°C. In order to achieve low
standby current, all inputs must be driven to either VDDQ or VSS. ISB might be set slightly
higher for up to 500ms after power-up, or when entering standby mode.
Table 13.
13 Deep Power-Down Specifications
Description
Deep Power-Down
Notes:
Conditions
Symbol
TYP
MAX
Unit
VIN=VDDQ or 0V
VDD,VDDQ=1.95V, +85°C
IDPD
3
10
uA
Typical (TYP) IDPD value applies across all operating temperatures and voltages.
Table 14. Capacitance
Description
Input Capacitance
Input/Output Capacitance (ADQ)
Notes:
Conditions
Symbol
MIN
MAX
Unit
Note
TC=+25°C;
f=1Mhz;
VIN=0V
CIN
2.0
6.0
pF
1
CIO
3.0
6.5
pF
1
1. These parameters are verified in device characterization and are not 100% tested.
Figure 15. AC Input/Output Reference Waveform
VDDQ
∫∫
VDDQ/22 Output
Test Points
VSS
VDDQ/23 Output
∫∫
Notes:
1. AC test inputs are driven at VDDQ for a logic 1 and VSS for a logic 0. Input rise and fall times
(10% to 90%) < 1.6ns.
2. Input timing begins at VDDQ/2.
3. Output timing ends at VDDQ/2.
Figure 16. Output Load Circuit
Test Point
50Ω
VDDQ/2
DUT
30pF
Notes:
All tests are performed with the outputs configured for default setting of half drive strength (BCR[5:4] = 01b).
Rev. A | July 2013
www.issi.com - [email protected]
29
IS66WVD1M16ALL
AC Characteristics
Table15 . Asynchronous READ Cycle Timing Requirements
Symbol
Parameter
-70
Min
Max
Unit
tAA
Address Acess Time
70
ns
tAADV
ADV# Access Time
70
ns
tAVH
Address hold from ADV# HIGH
2
ns
tAVS
Address setup to ADV# HIGH
5
ns
tBA
UB#,, LB# Access Time
70
tBHZ
UB#, LB# Disable to High-Z Output
7
tCPH
CE# HIGH between Subsequent Asynchronous cycles
tCO
Chip Select Access Time
tCVP
CE# low to ADV# HIGH
tHZ
Chip Disable to High-Z
High Z Output
7
tOE
OE# low to Valid Output
20
tOEW
OE# low to WAIT Valid
tOHZ
OE# high to High-Z Output
tOLZ
OE# low to Low-Z output
tVP
ADV# Low pulse width
tWZ
CE# high to WAIT High-Z
5
1
ns
70
7
1
ns
Notes
ns
ns
1
ns
7.5
7
ns
1
3
ns
2
7
ns
7
ns
1
Notes:
1. Low-Z to High-Z timings are tested with the circuit shown in Figure 23. The High-Z timings
measure a 100mV transition from either VOH or VOL toward VDDQ/2.
2. High-Z
High Z to Low-Z
Low Z timings are tested with the circuit shown in Figure 23. The Low
Low-Z
Z timings
measure a 100mV transition away from the High-Z (VDDQ/2) level toward either VOH or VOL.
Rev. A | July 2013
www.issi.com - [email protected]
30
IS66WVD1M16ALL
Table16 . Burst READ Cycle Timing Requirements
-7013
-7010
-7008
Symbol
Parameter
tAA
Address Acess Time (Fixed Latency)
70
70
70
ns
tAADV
ADV# Access Time (Fixed Latency)
70
70
70
ns
tABA
Burst to READ Access Time
(Variable Latency)
35.5
35.9
46.5
ns
tACLK
CLK to Output Delay
5.5
7
9
ns
1
tCBPH
CE# High between Subsequent
Burst or Mixed-Mode Operations
ns
2
tCEM
Maximum CE# Pulse width
us
2
tCLK
CLK Period
tCO
Chip Select Access Time (Fixed
Latency)
tCSP
CE# Setup Time to Active CLK Edge
tHD
Hold Time from Active CLK Edge
tHZ
Chip Disable to High-Z Output
tKH/tKL
Min
Max
5
Min
Max
5
4
7.5
Min
6
4
9.62
70
Max
4
70
ns
2.5
3
4
ns
2
2
2
ns
7
7
Note
ns
12.5
70
Unit
7
ns
3
CLK HIGH or LOW Time
3
3
4
ns
tKOH
Output Hold from CLK
2
2
2
ns
tKW
CLK to WAIT Valid
5.5
7
9
ns
tOE
Burst OE# LOW to Output Valid
20
20
20
ns
tOHZ
OE# high to High
High-Z
Z Output
7
7
7
ns
4
tOLZ
OE# low to Low-Z output
3
3
3
ns
4
tSP
Setup time to Active CLK Edge
2
3
3
ns
tT
CLK Rise or Fall Time
tWZ
CE# high to WAIT High-Z
1.2
1.6
1.8
ns
7
7
7
ns
1
3
Notes:
1. tACLK and tKW values for -7013 are for variable LC = 4 and fixed LC = 8 only. For other LC
settings, these parameters will be 7ns for -7013 devices.
2. A refresh opportunity must be provided every tCEM by taking CE# HIGH.
3. Low-Z to High-Z timings are tested with the circuit shown in Figure 16.
The High-Z timings measure a 100mV transition from either VOH or VOL toward VDDQ/2.
4. High-Z to Low-Z timings are tested with the circuit shown in Figure 16.
The Low-Z timings
g measure a 100mV transition awayy from the High-Z
g
((VDDQ/2)
Q/ ) level toward
either VOH or VOL.
Rev. A | July 2013
www.issi.com - [email protected]
31
IS66WVD1M16ALL
Table17 . Asynchronous WRITE Cycle Timing Requirements
Symbol
Parameter
-70
Min
Max
Unit
tAS
Address and ADV# LOW Setup Time
0
ns
tAVH
Address hold from ADV# HIGH
2
ns
tAVS
Address setup to ADV# HIGH
5
ns
tAW
Address Valid to End of Write
70
ns
tBW
UB#, LB# Select to End of Write
70
ns
tCPH
CE# HIGH between Subsequent Asynchronous cycles
5
ns
tCVP
CE# low to ADV# HIGH
7
ns
tCW
Chip Enable to End of Write
70
tDH
Data Hold from Write Time
0
tDS
Data Write Setup Time
20
tVP
ADV# Low pulse width
7
ns
tVS
ADV# Setup to End of Write
70
ns
Notes
ns
tWHZ
WRITE to ADQ High-Z Output
7
tWP
WRITE Pulse Width
45
ns
tWR
WRITE Recovery Time
0
ns
tWZ
CE# high to WAIT High-Z
7
ns
ns
1
2
Notes:
1. WE# must not remain LOW longer than 4μs (tCEM) while the device is selected (CE# LOW).
2. Low-Z to High-Z timings are tested with the circuit shown in Figure 16.
The High-Z timings measure a 100mV transition from either VOH or VOL toward VDDQ/2.
Rev. A | July 2013
www.issi.com - [email protected]
32
IS66WVD1M16ALL
Table18 . Burst WRITE Cycle Timing Requirements
Symbol
-7013
Parameter
Min
-7010
Max
Min
-7008
Max
Min
Max
Unit
Note
Address and ADV# LOW Setup
Time
0
0
0
ns
1
tCBPH
CE# High between Subsequent
Burst or Mixed-Mode Operations
5
5
6
ns
2
tCEM
Maximum CE# Pulse width
us
2
tCLK
CLK Period
7.5
9.62
12.5
ns
tCSP
CE# Setup Time to Active CLK
Edge
2.5
3
4
ns
tHD
Hold Time from Active CLK Edge
2
2
2
ns
CLK HIGH or LOW Time
3
3
4
ns
tAS
tKH/tKL
4
tKW
CLK to WAIT Valid
tSP
Setup time to Active CLK Edge
tT
CLK Rise or Fall Time
tWZ
CE# high to WAIT High-Z
4
5.5
2
4
7
ns
9
3
3
ns
3
1.2
1.6
1.8
ns
7
7
7
ns
4
Notes:
1. tAS required if tCSP > 20ns.
2. A refresh opportunity must be provided every tCEM by taking CE# HIGH.
3. tKW value for -7013 is for variable LC = 4 and fixed LC = 8 only. For other LC settings, this
parameter will be 7ns for -7013 devices.
4. Low-Z to High-Z timings are tested with the circuit shown in Figure 16.
The High-Z timings measure a 100mV transition from either VOH or VOL toward VDDQ/2.
Table19 . Initialization and DPD Timing Requirements
Symbol
Parameter
-70
Min
Max
Unit
tDPD
Time from DPD entry to DPD exit
150
us
tDPDX
CE# LOW time to exit DPD
70
ns
tPU
Initialization Period (required before normal operations)
Rev. A | July 2013
www.issi.com - [email protected]
150
Notes
us
33
IS66WVD1M16ALL
Timing Diagrams
Figure 17: Power-Up Initialization Timing
VDD, VDDQ=1.7V
VDD(MIN)
tPU > 150us
Device ready for
normal operation
Device Initialization
Figure 18: DPD Entry and Exit Timing Parameters
tDPD
tDPDX
tPU
DPD Enabled
DPD Exit
CE#
Write
RCR[4]=0
Device Initialization Device ready for
normal operation
Figure 19: Asynchronous READ
tAA
VALID
ADDRESS
Address
tAVS
ADQ0ADQ15
tAVH
VALID
ADDRESS
VALID
OUTPUT
tAADV
tVP
ADV#
tCVP
CE#
tWZ
tCO
tHZ
tBHZ
tBA
/
UB#/LB#
tOLZ
tOE
OE#
WE#
WAIT
Rev. A | July 2013
tOHZ
tOEW
HiZ
HiZ
www.issi.com - [email protected]
34
IS66WVD1M16ALL
Figure 20: CLK Timings for Burst Operations
tCLK
tT
Notes :
tCLK
tKL
tKH
1. For Burst timing diagrams, non-default BCR settings are shown
Rev. A | July 2013
www.issi.com - [email protected]
35
IS66WVD1M16ALL
Figure 21: Single Access Burst READ Operation – Variable Latency without refresh collision
tABA
tCLK
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tACLK
tHD
VALID
ADDRESS
tSP
ADV#
VALID
OUTPUT
tHD
tCSP
tHD
tCEM
CE#
tSP
UB#/LB#
tKOH
tHD
WE#
tOLZ
tOE
OE#
tOHZ
tKW
WAIT
tKW
HiZ
Read Burst Identified (WE#=HIGH)
Notes:
1. Non-default variable latency BCR settings for single-access burst READ operation: Latency
code two (three clocks); WAIT active LOW; WAIT asserted during delay.
Rev. A | July 2013
www.issi.com - [email protected]
36
IS66WVD1M16ALL
Figure 22: Four-Word Burst READ Operation – Variable Latency without refresh collision
tCLK
tABA
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tACLK
tHD
VALID
ADDRESS
tSP
ADV#
tKOH
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
tHD
tHZ
tHD
tCSP
tCEM
CE#
tSP
UB#/LB#
tSP
tHD
tHD
WE#
tOLZ
tOHZ
tOE
OE#
tWZ
tKW
WAIT
tCBPH
tKW
HiZ
Read Burst Identified (WE#=HIGH)
Notes:
1. Non-default variable latency BCR settings for 4-word burst READ operation: Latency code
two (three clocks); WAIT active LOW; WAIT asserted during delay.
Rev. A | July 2013
www.issi.com - [email protected]
37
IS66WVD1M16ALL
Figure 23: Four-Word Burst READ Operation – Variable Latency with refresh collision
tCLK
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tACLK
tHD
VALID
ADDRESS
tSP
ADV#
tKOH
VALID
OUTPUT
VALID
OUTPUT
tHZ
tHD
tCBPH
tCEM
CE#
tSP
tSP
VALID
OUTPUT
tHD
tCSP
UB#/LB#
VALID
OUTPUT
tHD
tWZ
tHD
WE#
tOLZ
tOE
OE#
tKW
WAIT
tKW
HiZ
Read Burst Identified (WE#=HIGH)
Notes:
1. Non-default variable latency BCR settings for 4-word burst READ operation: Latency code
two (three clocks); WAIT active LOW; WAIT asserted during delay.
2. If refresh collision happened, WAIT will be asserted between the latency count number of clock cycles
and 2x the latency count
Rev. A | July 2013
www.issi.com - [email protected]
38
IS66WVD1M16ALL
Figure 24: Single Access Burst READ Operation – Fixed Latency
tCLK
CLK
tAA
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tKOH
tHD
VALID
ADDRESS
VALID
OUTPUT
tAADV
tSP
ADV#
tHD
tHD
tCO
tCSP
CE#
tCEM
tSP
UB#/LB#
tSP
tHZ
tHD
tHD
WE#
tOHZ
tOLZ
tOE
OE#
tWZ
tKW
WAIT
tKW
HiZ
Read Burst Identified (WE#=HIGH)
Notes:
1. Non-default fixed latency BCR settings for single-access burst READ operation: Fixed Latency;
Latency code four (five clocks); WAIT active LOW; WAIT asserted during delay.
Rev. A | July 2013
www.issi.com - [email protected]
39
IS66WVD1M16ALL
Figure 25: Four-Word Burst READ Operation – Fixed Latency
tCLK
CLK
tAA
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tKOH
tHD
VALID
ADDRESS
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
tHZ
tAADV
tSP
ADV#
tHD
tCO
tHD
tCSP
tCEM
CE#
tSP
UB#/LB#
tSP
tCBPH
tHD
tHD
WE#
tOLZ
tOE
OE#
tWZ
tKW
WAIT
tKW
HiZ
Read Burst Identified (WE#=HIGH)
Notes:
1. Non-default fixed latency BCR settings for 4-word burst READ operation: Fixed latency;
latency code two (three clocks); WAIT active LOW; WAIT asserted during delay.
Rev. A | July 2013
www.issi.com - [email protected]
40
IS66WVD1M16ALL
Figure 26: READ Burst Suspend
CLK
Note2
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tKOH
tHD
VALID
ADDRESS
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
tHZ
tAADV
tSP
ADV#
tHD
tWZ
tCO
tCSP
tHD tCBPH
tHD
tHD
tCEM
CE#
tSP
UB#/LB#
tHD
tSP tHD
WE#
tOLZ
tOE
OE#
Note3
tKW
WAIT
Notes:
HiZ
tKW
1. Non-default BCR settings for READ burst suspend: Fixed or variable latency; latency code
two (three clocks); WAIT active LOW; WAIT asserted during delay.
2. CLK can be stopped LOW or HIGH, but must be static, with no LOW-to-HIGH transitions
during burst suspend.
3. OE# can stay LOW during BURST SUSPEND. If OE# is LOW, ADQ[15:0] will continue to
output valid data.
Rev. A | July 2013
www.issi.com - [email protected]
41
IS66WVD1M16ALL
Figure 27: Burst READ at End of Row (Wrap Off)
tCLK
CLK
Address
ADQ0ADQ15
VALID
OUTPUT
VALID
OUTPUT
VALID
OUTPUT
End of Row (A[7:0]=FFh)
ADV#
VIH
NOTE2
CE#
UB#/LB#
VIH
tHZ
VIL
VIL
WE#
OE#
VIL
tKW
tHZ
WAIT
Notes:
1. Non-default BCR settings for burst READ at end of row: fixed or variable latency; WAIT
active LOW; WAIT asserted during delay.
2. For burst READs, CE# must go HIGH before the third CLK after the WAIT period begins
(before the third CLK after WAIT asserts with BCR[8] = 0, or before the fourth CLK after
WAIT asserts with BCR[8] = 1).
Rev. A | July 2013
www.issi.com - [email protected]
42
IS66WVD1M16ALL
Figure 28: Asynchronous WRITE
tAW
tAS
Address
VALID
ADDRESS
tAVS
ADQ0ADQ15
tAVH
tDS
VALID
ADDRESS
tDH
VALID
DATA
tVS
tVP
ADV#
tCVP
CE#
tCW
tBW
UB#/LB#
tWP
WE#
WAIT3#
tAS
NOTE2
HiZ
HiZ
Notes:
1. The end of the WRITE cycle is controlled by CE#, UB#, LB#, or WE#, whichever de-asserts first.
2. WE# must not remain LOW longer than 4μs (tCEM) while the device is selected (CE# LOW).
3. During asynchronous WRITE cycles, WAIT will be High-Z while WE# is LOW or OE# is HIGH.
Rev. A | July 2013
www.issi.com - [email protected]
43
IS66WVD1M16ALL
Figure 29: Four-Word Burst WRITE Operation – Variable Latency
tCLK
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tSP
tHD
VALID
ADDRESS
NOTE3
tHD
DATA IN
DATA IN
DATA IN
DATA IN
tAS
tAS
ADV#
tHD
tCSP
tCEM
CE#
tCBPH
tSP
UB#/LB#
tSP
WE#
tHD
tHD
tHD
tKW
WAIT
tKW
HiZ
NOTE2
Write Burst Identified (WE#=LOW)
Notes:
1. Non-default BCR settings for burst WRITE operation, with fixed-length burst of 4, burst wrap enabled:
Variable latency; latency code two (three clocks); WAIT active LOW; WAIT asserted during delay.
2 WAIT asserts for LC cycles for both fixed and variable latency.
2.
latency LC = latency code (BCR[13:11]).
(BCR[13:11])
3. tAS required if tCSP > 20ns.
Rev. A | July 2013
www.issi.com - [email protected]
44
IS66WVD1M16ALL
Figure 30: Four-Word Burst WRITE Operation – Fixed Latency
tCLK
CLK
VALID
ADDRESS
Address
tSP
ADQ0ADQ15
tSP
tHD
VALID
ADDRESS
NOTE3
tAS
tHD
DATA IN
DATA IN
DATA IN
DATA IN
tAVH
tAS
ADV#
tHD
tCSP
tCEM
CE#
tCBPH
tSP
UB#/LB#
tSP
WE#
tHD
tHD
tHD
tKW
WAIT
tKW
HiZ
NOTE2
Write Burst Identified (WE#=LOW)
Notes:
1. Non-default BCR settings for burst WRITE operation, with fixed-length burst of 4, burst wrap enabled:
Fixed latency; latency code two (three clocks); WAIT active LOW; WAIT asserted during delay.
2 WAIT asserts for LC cycles for both fixed and variable latency.
2.
latency LC = latency code (BCR[13:11]).
(BCR[13:11])
3. tAS required if tCSP > 20ns.
Rev. A | July 2013
www.issi.com - [email protected]
45
IS66WVD1M16ALL
Figure 31: Continuous Burst WRITE at End-of-Row (Wrap Off)
tCLK
CLK
Address
ADQ0ADQ15
VALID
INPUT
VALID
INPUT
VALID
INPUT
End of Row (A[7:0]=FFh)
ADV#
VIH
NOTE2
CE#
VIH
tHZ
VIL
UB#/LB#
WE#
OE#
VIH
tKW
tHZ
WAIT
Notes:
1. Non-default BCR settings for burst WRITE at end of row: fixed or variable latency; WAIT
active LOW; WAIT asserted during delay.
2. For burst WRITEs, CE# must go HIGH before the third CLK after the WAIT period begins
(before the third CLK after WAIT asserts with BCR[8] = 0, or before the fourth CLK after
WAIT asserts with BCR[8] = 1).
Rev. A | July 2013
www.issi.com - [email protected]
46
IS66WVD1M16ALL
Figure 32: Burst WRITE followed by Burst READ
tCLK
tABA
CLK
VALID
ADDRESS
Address
VALID
ADDRESS
tSP tHD
tSP tHD
ADQ0ADQ15
VALID
ADDRESS
tSP tHD
DATA IN DATA IN DATA INDATA IN
tACLK
VALID
ADDRESS
tKOH
VALID VALID VALID VALID
OUTPUTOUTPUTOUTPUTOUTPUT
tAS
tAS
ADV#
tCBPH
tCSP
tCEM
tCEM
CE#
tSPtHD
tHD
UB#/LB#
tSP tHD
WE#
tOLZ
tOE
OE#
tKW
WAIT
tOHZ
HiZ
tKW
HiZ
tWZ
tKW
tKW
Notes:
1. Non-default BCR settings for burst WRITE followed by burst READ; latency code two (three clocks);
WAIT active LOW; WAIT asserted during delay.
2. A refresh opportunity must be provided every tCEM by taking CE# HIGH.
Rev. A | July 2013
www.issi.com - [email protected]
47
IS66WVD1M16ALL
Figure 33: Asynchronous WRITE followed by Burst READ
tCLK
CLK
tAW
VALID
ADDRESS
Address
tAVS
ADQ0ADQ15
VALID
ADDRESS
tAVH
tDS
tSP tHD
tDH
VALID
DATA
VALID
ADDRESS
tACLK
VALID
ADDRESS
tKOH
VALID
OUTPUT
tVS
tSP tHD
tVP
ADV#
tCSP
NOTE2
tCBPH
tCW
CE#
tBW
UB#/LB#
tWP
WE#
tCSP
tHD
tSP
tHD
tWR
tOLZ
tOE
OE#
tWZ
WAIT
tKW
HiZ
Notes:
1. Non-default BCR settings for asynchronous WRITE followed by burst READ: Fixed or variable latency;
latency code two (three clocks); WAIT active LOW; WAIT asserted during delay.
2. When transitioning between asynchronous WRITE and variable-latency burst READ operations,
CE# must go HIGH. CE# can stay LOW when transitioning to fixed
fixed-latency
latency burst READs.
A refresh opportunity must be provided every tCEM by taking CE# HIGH.
Rev. A | July 2013
www.issi.com - [email protected]
48
IS66WVD1M16ALL
Figure 34: Asynchronous WRITE followed by Asynchronous READ
VALID
ADDRESS
Address
VALID
ADDRESS
tAVS tAVH
ADQ0ADQ15
tDS
VALID
ADDRESS
tDH
tAVS tAVH
VALID
ADDRESS
VALID
DATA
tVS
tAADV
tVP
ADV#
tCVP
CE#
tVP
tCPP
tCW
tCPH
tBW
UB#/LB#
VALID
OUTPUT
tHZ
tCO
tBA
tWP
WE#
tOLZ
tOE
OE#
WAIT
tOEW
HiZ
HiZ
Notes:
1. CE# can stay LOW when transitioning between asynchronous operations. If CE# goes HIGH,
it must remain HIGH for at least tCPH to schedule the appropriate internal refresh operation.
Otherwise, tCPH is only required after CE#-controlled WRITEs.
Rev. A | July 2013
www.issi.com - [email protected]
49
IS66WVD1M16ALL
Figure 35: Asynchronous READ followed by WRITE at the Same Address
tAA
VALID
ADDRESS
Address
tDS
tAVS tAVH
ADQ0ADQ15
VALID
ADDRESS
VALID
OUTPUT
tDH
VALID
INPUT
tAADV
tVP
ADV#
tCVP
CE#
tCO
tBA
UB#/LB#
tWP
WE#
tOLZ
tOE
OE#
WAIT
Notes:
HiZ
tWZ
tOEW
HiZ
1. The end of the WRITE cycle is controlled by CE#, UB#, LB#, or WE#, whichever de-asserts first.
2. WE# must not remain LOW longer than 4μs (tCEM) while the device is selected (CE# LOW).
Rev. A | July 2013
www.issi.com - [email protected]
50
IS66WVD1M16ALL
Ordering Information – VDD = 1.8V
Industrial Temperature Range: (-40oC to +85oC)
Config.
Speed
(ns)
Frequency
(MHz)
1Mx16
70
Rev. A | July 2013
Order Part No.
Package
133
IS66WVD1M16ALL-7013BLI
54-ball VFBGA
104
IS66WVD1M16ALL-7010BLI
54-ball VFBGA
80
IS66WVD1M16ALL-7008BLI
54-ball VFBGA
www.issi.com - [email protected]
51
IS66WVD1M16ALL
Rev. A | July 2013
www.issi.com - [email protected]
52