SPU0414HR5H-SB

SPU0414HR5H-SB
Amplified SiSonicTM Microphone
The SPU0414HR5H-SB is a miniature, highperformance, low power, top port silicon
microphone. Using Knowles’ proven high
performance SiSonicTM MEMS technology,
the SPU0414HR5H-SB consists of an
acoustic sensor, a low noise input buffer,
and an output amplifier. These devices are
suitable for applications such as cellphones,
smart phones, laptop computers, sensors,
digital still cameras, portable music
recorders, and other portable electronic
devices where excellent wideband audio
performance and RF immunity are required.
Revision: G
Sheet 1 of 11
Features:
 Up to 20dB of Gain
 Low Current
 Small package
 MaxRF protection
 Ultra-Stable Performance
 Standard SMD Reflow
 Omnidirectional
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
1.
ABSOLUTE MAXIMUM RATINGS
Parameter
Absolute Maximum Rating
Units
VDD to Ground
-0.5, +5.0
V
OUT to Ground
-0.3, VDD + 0.3
V
±5
mA
-40 to +100
°C
Input Current to Any Pin
Temperature Range
Stresses exceeding these “Absolute Maximum Ratings” may cause permanent damage to the device. These are
stress ratings only. Functional operation at these or any other conditions beyond those indicated under “Acoustic
& Electrical Specifications” is not implied. Exposure beyond those indicated under “Acoustic & Electrical
Specifications” for extended periods may affect device reliability.
2.
ACOUSTIC & ELECTRICAL SPECIFICATIONS
TEST CONDITIONS: 23 ±2°C, 55±20% R.H., VDD(min) < VDD < VDD(max), no load, unless otherwise indicated
Parameter
Symbol
1
1,2
Supply Voltage
Supply Current
Sensitivity
1
Signal to Noise Ratio
Total Harmonic
Distortion
Acoustic Overload
Point
Min
Typ
Max
Units
VDD
1.5
-
3.6
V
IDD
-
155
220
µA
S
94 dB SPL @ 1 kHz
-25
-22
-19
dBV/Pa
SNR
94 dB SPL @ 1 kHz, A-weighted
-
59
-
dB(A)
-
-
1
%
1153
-
-
dB SPL
VDD = 1.5V
-
0.93
-
V
@ 1 kHz
-
-
400

THD
AOP
DC Output
Output Impedance
Conditions
ZOUT
94 dB SPL @ 1 kHz,
S = Typ, Rload > 2 k
10% THD @ 1 kHz,
S = Typ, VDD = 3.6V, Rload > 2 k
Directivity
Polarity
Omnidirectional
Increasing sound pressure
Decreasing output voltage
1
100% tested.
Maximum specifications are measured at maximum VDD. Typical specifications are measured at VDD = 1.8V.
3
For gain = 20dB, AOP(min) = 95 dB SPL.
2
Revision: G
Sheet 2 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
3.
FREQUENCY RESPONSE CURVE
Sensitivity (dB)
Typical Free Field Response
Normalized to 1 kHz (C1 = 2.2mF, R1 = 0)
20
18
16
14
12
10
8
6
4
2
0
-2
-4
-6
-8
-10
-12
-14
-16
-18
-20
100
1,000
10,000
Frequency (Hz)
Revision: G
Sheet 3 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
4.
INTERFACE CIRCUIT
VDD
.1mf
VDD
OUTPUT
RS = 2.44k
RF = 22k
GROUND
Dotted Section
Represents
SiSonicTM
Microphone
GAIN
R1 (Set By User)
C1 (Set By User)
Gain
GAIN Pin Termination
Unity Gain (0dB)
Connect GAIN to OUTPUT
Set R1 = 0Set C1 according to equation below:
Max Gain (20dB)
Highpass corner frequency =
Set R1 and C1 according to the equations below:
Adjustable Gain
(0dB to 20dB)
Gain(dB) =
Highpass corner frequency =
Note: Capacitors near the microphone should not contain Class 2 dielectrics.
Detailed information on acoustic, mechanical, and system integration can be found in
the latest SiSonicTM Design Guide application note.
Revision: G
Sheet 4 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
5.
MECHANICAL SPECIFICATIONS
Item
Dimension
Tolerance
Length (L)
3.76
±0.10
Width (W)
2.95
±0.10
Height (H)
1.10
±0.10
Ø0.50
±0.05
Acoustic Port (AP)
Pin #
Pin Name
Type
Description
1
VDD
Power
Power Supply
2
GROUND
Power
Ground
3
GAIN
Signal
Connect resistor to set gain
4
OUTPUT
Signal
Output Signal
Notes: Pick Area only extends to 0.25 mm of any edge or hole unless otherwise specified.
Dimensions are in millimeters unless otherwise specified.
Tolerance is ±0.15mm unless otherwise specified
Revision: G
Sheet 5 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
6.
EXAMPLE LAND PATTERN
7.
EXAMPLE SOLDER STENCIL PATTERN
Notes: Dimensions are in millimeters unless otherwise specified.
Further optimizations based on application should be performed.
Revision: G
Sheet 6 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
8.
PACKAGING & MARKING DETAIL
Model Number
Suffix
Reel Diameter
Quantity Per Reel
SPU0414HR5H-SB
-7
13”
5,700
Pin 1
Alpha Character A:
“S”: Knowles SiSonicTM Production
“E”: Knowles Engineering Samples
“P”: Knowles Prototype Samples
“JIN NUMBER”:
Unique Job Identification Number
for product traceability
Notes: Dimensions are in millimeters unless otherwise specified.
Vacuum pickup only in the pick area indicated in Mechanical Specifications.
Tape & reel per EIA-481.
Labels applied directly to reel and external package.
Shelf life: Twelve (12) months when devices are to be stored in factory supplied,
unopened ESD moisture sensitive bag under maximum environmental conditions of
30°C, 70% R.H.
Revision: G
Sheet 7 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
9.
RECOMMENDED REFLOW PROFILE
tP
TP
Ramp-up
Temperature
TL
tL
TSMAX
TSMIN
tS Preheat
Ramp-down
25°C
Time
Time 25°C to Peak
Profile Feature
Average Ramp-up rate (TSMAX to TP)
Preheat
 Temperature Min (TSMIN)
 Temperature Max (TSMAX)
 Time (TSMIN to TSMAX) (tS)
Time maintained above:
 Temperature (TL)
 Time (tL)
Peak Temperature (TP)
Time within 5°C of actual Peak Temperature (tP)
Ramp-down rate (TP to TSMAX)
Time 25°C to Peak Temperature
Pb-Free
3°C/second max.
150°C
200°C
60-180 seconds
217°C
60-150 seconds
260°C
20-40 seconds
6°C/second max
8 minutes max
Notes: Based on IPC/JDEC J-STD-020 Revision C.
All temperatures refer to topside of the package, measured on the package body
surface.
Revision: G
Sheet 8 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
10. ADDITIONAL NOTES
(A) MSL (moisture sensitivity level) Class 1.
(B) Maximum of 3 reflow cycles is recommended.
(C) In order to minimize device damage:
 Do not board wash or clean after the reflow process.
 Do not brush board with or without solvents after the reflow process.
 Do not directly expose to ultrasonic processing, welding, or cleaning.
 Do not insert any object in port hole of device at any time.
 Do not apply over 30 psi of air pressure into the port hole.
 Do not pull a vacuum over port hole of the microphone.
 Do not apply a vacuum when repacking into sealed bags at a rate faster than 0.5 atm/sec.
11. MATERIALS STATEMENT
Meets the requirements of the European RoHS directive 2011/65/EC as amended.
Meets the requirements of the industry standard IEC 61249-2-21:2003 for halogenated
substances and Knowles Green Materials Standards Policy section on Halogen-Free.
Ozone depleting substances are not used in the product or the processes used to make the
product, including compounds listed in Annex A, B, and C of the “Montreal Protocol on
Substances That Deplete the Ozone Layer.”
Revision: G
Sheet 9 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
12. RELIABILITY SPECIFICATIONS
Test
Description
Thermal Shock
100 cycles air-to-air thermal shock from -40oC to +125oC with 15
minute soaks. (IEC 68-2-4)
High Temperature Storage
1,000 hours at +105oC environment (IEC 68-2-2 Test Ba)
Low Temperature Storage
1,000 hours at -40oC environment (IEC 68-2-2 Test Aa)
High Temperature Bias
1,000 hours at +105oC under bias (IEC 68-2-2 Test Ba)
Low Temperature Bias
1,000 hours at -40oC under bias (IEC 68-2-2 Test Aa)
Temperature / Humidity Bias
1,000 hours at +85oC/85% R.H. under bias. (JESD22-A101A-B)
Vibration
ESD-HBM
ESD-LID/GND
ESD-MM
4 cycles of 20 to 2,000 Hz sinusoidal sweep with 20 G peak
acceleration lasting 12 minutes in X, Y, and Z directions.
(Mil-Std-883E, Method 2007.2 A)
3 discharges of ±2 kV direct contact to I/O pins.
(MIL 883E, Method 3015.7)
3 discharges of ±8 kV direct contact to lid while unit is grounded.
(IEC 61000-4-2)
3 discharges of ±200 V direct contact to I/O pins.
(ESD STM5.2)
Reflow
5 reflow cycles with peak temperature of +260oC
Mechanical Shock
3 pulses of 10,000 G in the X, Y, and Z direction (IEC 68-2-27, Test Ea)
Note: After reliability tests are performed, the sensitivity of the microphones shall not deviate
more than 3 dB from its initial value.
Revision: G
Sheet 10 of 11
3/27/2013
©2013 Knowles Electronics
SPU0414HR5H-SB
13. SPECIFICATION REVISIONS
Revision
Specification Changes
Date
A
Initial Release (C10109400)
4/23/09
C
Update Sections 2, 3, 4, 6, 8; misc cleanup (C10112517)
10/21/10
D
Update Section 2, 3, 7, 8, 10, 11; misc cleanup (C10113579)
11/10/11
E
Released in new format; add DC Output; new JIN designation (C10114423)
12/04/12
F
New RoHS statement (C10114438)
12/17/12
G
Updated humidity conditions and ESD descriptions (C10114466); moved
Shelf Life information to Section 8; fixed typos in Reliability Section 12
(C10114690)
3/27/13
Information contained herein is subject to change without notice. It may be used by a party at their own discretion
and risk. We do not guarantee any results or assume any liability in connection with its use. This publication is not
to be taken as a license to operate under any existing patents.
Revision: G
Sheet 11 of 11
3/27/2013
©2013 Knowles Electronics