RENESAS HM62W8512BLFP-7

To all our customers
Regarding the change of names mentioned in the document, such as Hitachi
Electric and Hitachi XX, to Renesas Technology Corp.
The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and other Hitachi brand
names are mentioned in the document, these names have in fact all been changed to Renesas
Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and
corporate statement, no changes whatsoever have been made to the contents of the document, and
these changes do not constitute any alteration to the contents of the document itself.
Renesas Technology Home Page: http://www.renesas.com
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
Cautions
Keep safety first in your circuit designs!
1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corporation product best suited to the customer's application; they do not convey any
license under any intellectual property rights, or any other rights, belonging to Renesas Technology
Corporation or a third party.
2. Renesas Technology Corporation assumes no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corporation without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corporation
or an authorized Renesas Technology Corporation product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corporation assumes no responsibility for any damage, liability, or other loss
rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corporation by various
means, including the Renesas Technology Corporation Semiconductor home page
(http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams,
charts, programs, and algorithms, please be sure to evaluate all information as a total system before
making a final decision on the applicability of the information and products. Renesas Technology
Corporation assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device
or system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor
when considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be
exported under a license from the Japanese government and cannot be imported into a country other
than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corporation for further details on these materials or the products
contained therein.
HM62W8512B Series
4 M SRAM (512-kword × 8-bit)
ADE-203-904F (Z)
Rev. 5.0
Mar. 15, 2000
Description
The Hitachi HM62W8512B is a 4-Mbit static RAM organized 512-kword × 8-bit. It realizes higher density,
higher performance and low power consumption by employing 0.35 µm Hi-CMOS process technology. The
device, packaged in a 525-mil SOP (foot print pitch width) or 400-mil TSOP TYPE II is available for high
density mounting. The HM62W8512B is suitable for battery backup system.
Features
• Single 3.3 V supply: 3.3 V ± 0.3 V
• Access time: 55/70 ns (max)
• Power dissipation
 Active: 16.5 mW/MHz (typ)
 Standby: 3.3 µW (typ)
• Completely static memory. No clock or timing strobe required
• Equal access and cycle times
• Common data input and output: Three state output
• Directly LV-TTL compatible: All inputs and outputs
• Battery backup operation
HM62W8512B Series
Ordering Information
Type No.
Access time
Package
HM62W8512BLFP-5
HM62W8512BLFP-7
55 ns
70 ns
525-mil 32-pin plastic SOP (FP-32D)
HM62W8512BLFP-5SL 55 ns
HM62W8512BLFP-7SL 70 ns
HM62W8512BLFP-5UL 55 ns
HM62W8512BLFP-7UL 70 ns
HM62W8512BLTT-5
HM62W8512BLTT-7
55 ns
70 ns
HM62W8512BLTT-5SL
HM62W8512BLTT-7SL
55 ns
70 ns
400-mil 32-pin plastic TSOP II (TTP-32D)
HM62W8512BLTT-5UL 55 ns
HM62W8512BLTT-7UL 70 ns
HM62W8512BLRR-5
HM62W8512BLRR-7
55 ns
70 ns
HM62W8512BLRR-5SL 55 ns
HM62W8512BLRR-7SL 70 ns
HM62W8512BLRR-5UL 55 ns
HM62W8512BLRR-7UL 70 ns
2
400-mil 32-pin plastic TSOP II reverse (TTP-32DR)
HM62W8512B Series
Pin Arrangement
HM62W8512BLFP Series
A18
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
A15
A17
WE
A13
A8
A9
A11
OE
A10
CS
I/O7
I/O6
I/O5
I/O4
I/O3
(Top view)
HM62W8512BLTT Series
A18
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
A15
A17
WE
A13
A8
A9
A11
OE
A10
CS
I/O7
I/O6
I/O5
I/O4
I/O3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A18
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
(Top view)
HM62W8512BLRR Series
VCC
A15
A17
WE
A13
A8
A9
A11
OE
A10
CS
I/O7
I/O6
I/O5
I/O4
I/O3
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
(Top view)
Pin Description
Pin name
Function
A0 to A18
Address input
I/O0 to I/O7
Data input/output
CS
Chip select
OE
Output enable
WE
Write enable
VCC
Power supply
VSS
Ground
3
HM62W8512B Series
Block Diagram
A18
V CC
A16
V SS
A1
A0
A2
A12
Row
Decoder
•
•
•
•
•
Memory Matrix
1,024 × 4,096
•
•
Column I/O
A14
A3
A7
A6
I/O0
Input
Data
Control
Column Decoder
I/O7
A13 A17A15 A8 A9 A11A10 A4 A5
••
CS
WE
OE
4
Timing Pulse Generator
Read/Write Control
•
•
HM62W8512B Series
Function Table
WE
CS
OE
Mode
VCC current
Dout pin
Ref. cycle
×
H
×
Not selected
I SB , I SB1
High-Z
—
H
L
H
Output disable
I CC
High-Z
—
H
L
L
Read
I CC
Dout
Read cycle
L
L
H
Write
I CC
Din
Write cycle (1)
L
L
L
Write
I CC
Din
Write cycle (2)
Note: ×: H or L
Absolute Maximum Ratings
Parameter
Symbol
Value
Power supply voltage
VCC
–0.5 to +4.6
1
Unit
V
2
Voltage on any pin relative to V SS
VT
–0.5* to V CC + 0.5*
V
Power dissipation
PT
1.0
W
Operating temperature
Topr
–20 to +70
°C
Storage temperature
Tstg
–55 to +125
°C
Storage temperature under bias
Tbias
–20 to +85
°C
Notes: 1. –3.0 V for pulse half-width ≤ 30 ns
2. Maximum voltage is 4.6 V
Recommended DC Operating Conditions (Ta = –20 to +70°C)
Parameter
Symbol
Min
Typ
Max
Unit
Supply voltage
VCC
3.0
3.3
3.6
V
VSS
0
0
0
V
VIH
2.0
—
VCC + 0.3
V
—
0.8
V
Input high voltage
Input low voltage
Note:
VIL
1
–0.3*
1. –3.0 V for pulse half-width ≤ 30 ns
5
HM62W8512B Series
DC Characteristics (Ta = –20 to +70°C, VCC = 3.3 V ± 0.3 V, VSS = 0 V)
Parameter
Symbol
Min
Typ*1
Max
Unit Test conditions
Input leakage current
|ILI|
—
—
1
µA
Vin = VSS to V CC
Output leakage current
|ILO |
—
—
1
µA
CS = VIH or OE = VIH or
WE = VIL, VI/O = VSS to V CC
Operating power
supply current: DC
I CC
—
—
10
mA
CS = VIL,
others = VIH/VIL, I I/O = 0 mA
HM62W8512B-5 I CC1
—
—
45
mA
Min cycle, duty = 100%
CS = VIL, others = VIH/VIL
I I/O = 0 mA
HM62W8512B-7 I CC1
—
—
40
mA
Operating
power supply
current
Operating power
supply current
I CC2
—
5
10
mA
Cycle time = 1 µs,
duty = 100%
I I/O = 0 mA, CS ≤ 0.2 V
VIH ≥ V CC – 0.2 V,
VIL ≤ 0.2 V
Standby power supply
current: DC
I SB
—
0.1
0.3
mA
CS = VIH
Standby power supply
current (1): DC
I SB1
—
1* 2
40* 2
µA
Vin ≥ 0 V,
CS ≥ V CC – 0.2 V
—
1* 3
20* 3
µA
—
1*
4
—
—
0.4
V
I OL = 2.0 mA
—
—
0.2
V
I OL = 100 µA
VCC – 0.2 —
—
V
I OH = –100 µA
2.4
—
V
I OH = –2.0 mA
Output low voltage
VOL
Output high voltage
Notes: 1.
2.
3.
4.
VOH
5*
—
4
µA
Typical values are at VCC = 3.3 V, Ta = +25°C and specified loading, and not guaranteed.
This characteristics is guaranteed only for L version.
This characteristics is guaranteed only for L-SL version.
This characteristics is guaranteed only for L-UL version.
Capacitance (Ta = +25°C, f = 1 MHz)
Parameter
1
Input capacitance*
Input/output capacitance*
Note:
6
1
Symbol
Typ
Max
Unit
Test conditions
Cin
—
8
pF
Vin = 0 V
CI/O
—
10
pF
VI/O = 0 V
1. This parameter is sampled and not 100% tested.
HM62W8512B Series
AC Characteristics (Ta = –20 to +70°C, VCC = 3.3 V ±0.3 V, unless otherwise noted.)
Test Conditions
•
•
•
•
Input pulse levels: 0.4 V to 2.4 V
Input rise and fall time: 5 ns
Input timing reference levels: 1.4 V
Output timing reference level: 1.4 V/1.4 V(HM62W8512B-5)
0.8 V/2.0 V(HM62W8512B-7)
• Output load (Including scope & jig)
500 Ω
Dout
1.4 V
50 pF
Read Cycle
HM62W8512B
-5
-7
Parameter
Symbol
Min
Max
Min
Max
Unit
Notes
Read cycle time
t RC
55
—
70
—
ns
Address access time
t AA
—
55
—
70
ns
Chip select access time
t CO
—
55
—
70
ns
Output enable to output valid
t OE
—
30
—
35
ns
Chip selection to output in low-Z
t LZ
10
—
10
—
ns
2
Output enable to output in low-Z
t OLZ
5
—
5
—
ns
2
Chip deselection to output in high-Z
t HZ
0
20
0
30
ns
1, 2
Output disable to output in high-Z
t OHZ
0
20
0
30
ns
1, 2
Output hold from address change
t OH
10
—
10
—
ns
7
HM62W8512B Series
Write Cycle
HM62W8512B
-5
-7
Parameter
Symbol
Min
Max
Min
Max
Unit
Notes
Write cycle time
t WC
55
—
70
—
ns
Chip selection to end of write
t CW
50
—
60
—
ns
4
Address setup time
t AS
0
—
0
—
ns
5
Address valid to end of write
t AW
50
—
60
—
ns
Write pulse width
t WP
40
—
50
—
ns
3, 12
Write recovery time
t WR
0
—
0
—
ns
6
WE to output in high-Z
t WHZ
0
20
0
30
ns
1, 2, 7
Data to write time overlap
t DW
25
—
30
—
ns
Data hold from write time
t DH
0
—
0
—
ns
Output active from output in high-Z
t OW
5
—
5
—
ns
2
Output disable to output in high-Z
t OHZ
0
20
0
30
ns
1, 2, 7
Notes: 1. t HZ , t OHZ and t WHZ are defined as the time at which the outputs achieve the open circuit conditions and
are not referred to output voltage levels.
2. This parameter is sampled and not 100% tested.
3. A write occurs during the overlap (tWP) of a low CS and a low WE. A write begins at the later
transition of CS going low or WE going low. A write ends at the earlier transition of CS going high
or WE going high. tWP is measured from the beginning of write to the end of write.
4. t CW is measured from CS going low to the end of write.
5. t AS is measured from the address valid to the beginning of write.
6. t WR is measured from the earlier of WE or CS going high to the end of write cycle.
7. During this period, I/O pins are in the output state so that the input signals of the opposite phase to
the outputs must not be applied.
8. If the CS low transition occurs simultaneously with the WE low transition or after the WE transition,
the output remain in a high impedance state.
9. Dout is the same phase of the write data of this write cycle.
10. Dout is the read data of next address.
11. If CS is low during this period, I/O pins are in the output state. Therefore, the input signals of the
opposite phase to the outputs must not be applied to them.
12. In the write cycle with OE low fixed, tWP must satisfy the following equation to avoid a problem of
data bus contention. t WP ≥ tDW min + tWHZ max
8
HM62W8512B Series
Timing Waveforms
Read Timing Waveform (WE = VIH)
tRC
Address
tAA
tCO
CS
tLZ
tHZ
tOE
tOLZ
OE
tOHZ
Dout
Valid Data
tOH
9
HM62W8512B Series
Write Timing Waveform (1) (OE Clock)
tWC
Address
tAW
tWR
OE
tCW
CS
*8
tWP
tAS
WE
tOHZ
Dout
tDW
Din
10
Valid Data
tDH
HM62W8512B Series
Write Timing Waveform (2) (OE Low Fixed)
tWC
Address
tCW
tWR
CS
*8
tAW
tWP
WE
tOH
tAS
tOW
tWHZ
*9
*10
Dout
tDW
tDH
*11
Din
Valid Data
11
HM62W8512B Series
Low VCC Data Retention Characteristics (Ta = –20 to +70°C)
Parameter
Symbol
Min
Typ
VCC for data retention
VDR
2
—
Data retention current
I CCDR
Chip deselect to data retention time
Operation recovery time
t CDR
tR
5
—
0.8*
—
0.8*5
—
5
0.8*
0
t RC*
6
Max
Unit Test conditions*4
—
V
CS ≥ V CC – 0.2 V, Vin ≥ 0 V
1
µA
VCC = 3.0 V, Vin ≥ 0 V
CS ≥ V CC – 0.2 V
10* 2
µA
20*
2*
3
µA
—
—
ns
—
—
ns
See retention waveform
For L-version and 10 µA (max.) at Ta = –20 to +40°C.
For L-SL-version and 3 µA (max.) at Ta = –20 to +40°C.
For L-UL-version and 2 µA (max.) at Ta = –20 to +40°C.
CS controls address buffer, WE buffer, OE buffer, and Din buffer. In data retention mode, Vin
levels (address, WE, OE, I/O) can be in the high impedance state.
5. Typical values are at VCC = 3.0 V, Ta = +25°C and specified loading, and not guaranteed.
6. t RC = read cycle time.
Notes: 1.
2.
3.
4.
Low V CC Data Retention Timing Waveform (CS Controlled)
t CDR
Data retention mode
V CC
3.0 V
V DR
2.0 V
CS
0V
12
CS ≥ VCC – 0.2 V
tR
HM62W8512B Series
Package Dimensions
HM62W8512BLFP Series (FP-32D)
Unit: mm
20.45
20.95 Max
17
11.30
32
1
1.27
*0.40 ± 0.08
0.38 ± 0.06
0.10
0.15 M
*Dimension including the plating thickness
Base material dimension
0.12
0.15 +– 0.10
1.00 Max
*0.22 ± 0.05
0.20 ± 0.04
3.00 Max
16
14.14 ± 0.30
1.42
0° – 8°
0.80 ± 0.20
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
FP-32D
Conforms
—
1.3 g
13
HM62W8512B Series
Package Dimensions (cont.)
HM62W8512BLTT Series (TTP-32D)
Unit: mm
20.95
21.35 Max
17
10.16
32
1.27
*0.42 ± 0.08
0.40 ± 0.06
0.21
16
M
0.80
11.76 ± 0.20
0.10
*Dimension including the plating thickness
Base material dimension
14
*0.17 ± 0.05
0.125 ± 0.04
1.20 Max
1.15 Max
0.13 ± 0.05
1
0° – 5° 0.50 ± 0.10
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
TTP-32D
Conforms
—
0.51 g
HM62W8512B Series
Package Dimensions (cont.)
HM62W8512BLRR Series (TTP-32DR)
Unit: mm
20.95
21.35 Max
16
10.16
1
1.27
*0.42 ± 0.08
0.40 ± 0.06
0.21
17
M
0.80
11.76 ± 0.20
0.10
*Dimension including the plating thickness
Base material dimension
*0.17 ± 0.05
0.125 ± 0.04
1.20 Max
1.15 Max
0.13 ± 0.05
32
0° – 5° 0.50 ± 0.10
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
TTP-32DR
Conforms
—
0.51 g
15
HM62W8512B Series
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual
property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of
bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic,
safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for
maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and
other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the
guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or
failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the
equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage
due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL
NorthAmerica
: http:semiconductor.hitachi.com/
Europe
: http://www.hitachi-eu.com/hel/ecg
Asia (Singapore)
: http://www.has.hitachi.com.sg/grp3/sicd/index.htm
Asia (Taiwan)
: http://www.hitachi.com.tw/E/Product/SICD_Frame.htm
Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm
Japan
: http://www.hitachi.co.jp/Sicd/index.htm
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive,
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
Hitachi Europe GmbH
Electronic components Group
Dornacher Straße 3
D-85622 Feldkirchen, Munich
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Europe Ltd.
Electronic Components Group.
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 778322
Hitachi Asia Pte. Ltd.
16 Collyer Quay #20-00
Hitachi Tower
Singapore 049318
Tel: 535-2100
Fax: 535-1533
Hitachi Asia Ltd.
Taipei Branch Office
3F, Hung Kuo Building. No.167,
Tun-Hwa North Road, Taipei (105)
Tel: <886> (2) 2718-3666
Fax: <886> (2) 2718-8180
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower, World Finance Centre,
Harbour City, Canton Road, Tsim Sha Tsui,
Kowloon, Hong Kong
Tel: <852> (2) 735 9218
Fax: <852> (2) 730 0281
Telex: 40815 HITEC HX
Copyright © Hitachi, Ltd., 1998. All rights reserved. Printed in Japan.
16