MI Series Aluminum Electrolytic Capacitors (85°C,7mmL) MERITEK FEATURES For general purposes series with 7mm height. SPECIFICATIONS Item Characteristic Operating Temp Range - 40 ~ +85C Rated Working Voltage 4 ~ 63VDC Capacitance Tolerance (120Hz 20C) 20%(M) I 0.01CV or 3 (A) Leakage Current I : Leakage Current (A) C : Rated Capacitance(F) V : Working Voltage (V) (20C) ＊Whichever is greater after 2 minutes Surge Voltage W.V. 4 (20C) S.V. Dissipation Factor ( tan ) (120Hz 20C) W.V. tan Low Temperature Stability Load Life Shelf Life 6.3 10 16 25 35 50 63 5 8 13 20 32 44 63 4 6.3 10 16 25 35 50~63 0.35 0.24 0.20 0.16 0.14 0.12 0.10 79 Impedance ratio at 120Hz Rated Voltage (V) 4 6.3 10 16 25 35 50~63 -25C / +20C 6 4 3 2 2 2 2 -40C / +20C 12 8 6 4 4 3 3 After 1000 hours application of W.V. and +85C ripple current value , the capacitor shall meet the following limits. ( DC + ripple peak voltage rated working voltage ) Capacitance Change 20% of initial. Dissipation Factor 200% of initial specified value Leakage Current initial specified value At +85C no voltage application after 1000 hours the capacitor shall meet the limits for load life characteristics. ( with voltage treatment ) PART NUMBER S YSTEM DIMENSIONS (mm) MI 50V 330 M TA 8x7 Meritek Series Rated Voltage Rated Capacitance Express in micro farad(uF), First two digits are significant figures, Third digit denotes number of zeros. ‘R’ denotes decimal point for values less than 10uF Tolerance M - 20% Package Code TA Tape & Ammo TR Tape & Reel Blank Case size – (D) Diameter x (L) Length in mm (Optional) D F d a 4 1.5 0.45 1.0 5 2.0 0.45 1.0 6.3 2.5 0.45 1.0 8 3.5 0.50 1.0 Rev. 7a MI Series Aluminum Electrolytic Capacitors (85°C,7mmL) MERITEK CASE SIZE & MAX RIPPLE CURRENT V Cap. (uF) Item 4 DxL R.C. 6.3 DxL R.C. 10 DxL 16 R.C. DxL R.C. Case size : DxL (mm) Max. ripple current : mA(rms) 85C 120Hz 25 35 50 63 DxL R.C. DxL R.C. DxL R.C. DxL R.C. 0.1 0.22 0.33 0.47 1.0 2.2 3.3 4.7 4x7 4x7 4 6 7 8 4x7 4x7 7 8 12 18 4x7 4x7 12 18 4x7 22 4x7 20 24 4x7 4x7 22 26 5x7 6.3x7 25 34 30 44 4x7 5x7 32 55 5x7 6.3x7 39 65 6.3x7 8x7 49 85 6.3x7 49 8x7 8x7 95 110 8x7 8x7 100 110 36 4x7 33 47 4x7 4x7 37 44 4x7 5x7 44 60 4x7 5x7 49 65 5x7 5x7 60 75 6.3x7 8x7 75 100 100 220 5x7 6.3x7 70 120 6.3x7 8x7 100 170 6.3x7 8x7 110 190 6.3x7 8x7 120 210 8x7 150 330 8x7 170 8x7 210 4x7 4 6 4x7 4x7 40 4x7 10 22 4x7 4x7 4x7 4x7 4x7 4x7 All blank voltage on sleeve marking is the same voltage as “” point to. Rev. 7a MI Series Aluminum Electrolytic Capacitors (85°C,7mmL) MERITEK TAPING SPECIFICATION Lead taping is designed for automatic insertion equipment. Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type. DIMENSIONS (Ø4~ Ø10) Item Symbol Case Size 4x5 5 x 5 6.3x5 8 x 5 4x7 5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16 0.45 0.5 10x18 10x20 Tolerance Lead wire diameter d Body height A Intervals of bodies P 12.7 ±1.0 Intervals of punched holes P0 12.7 ±0.2 6.0 8.0 12.5 13 14 0.6 ±0.05 17.5 19.5 21.5 MAX 3.85 Distance between holes and lead wire P1 5.35 5.1 5.1 5.6 Distance between holes and bodies 5.35 5.1 5.35 5.1 5.1 5.6 5.1 ±0.7 5.1 5.35 5.1 4.6 5.35 5.1 P2 F 6.35 2.0 2.5 2.5 2.0 2.5 2.5 Fig 1. Fig 4. Fig 2. Fig 3. 4.6 ±1.0 Fig 1. Fig 4. 5.0 Distance between lead and lead Remark +0.8 -0.2 2.5 Fig 2. F1:5.0 +0.5 -1.0 1.5 2.0 2.5 2.5 1.5 Fig 3. F1:5.0 2.0 2.5 3.5 2.0 2.5 3.5 +0.5 -1.0 Base tape width W W0 18.0 ±0.5 12.5 MIN Deviation between holes and base tape W1 9.0 ±0.5 Deviation between adhesive and base tape W2 1.5 MAX Adhesive tape width 17.5 18.5 20.0 17.5 18.5 18.5 18.5 Distance between body bottom and tape center H Lead wire clinched height H0 Distance between body top and tape center H1 Punched hole diameter D0 4.0 ±0.3 Length of not good lead slit L 11.0 MAX Base and adhesive tape thickness t 0.6 ±0.3 Deviation of body alignment ∆h 0 ±2.0 Deviation of body alignment ∆h1 0 ±1.0 ±0.5 16.0 24.5 Fig 1. Fig 4. Fig 2. Fig 3. ±0.5 27.5 32.5 33.0 36.0 38.0 41.0 MAX Rev. 7a MI Series Aluminum Electrolytic Capacitors (85°C,7mmL) MERITEK DIMENSIONS (Ø12.5~ Ø18) Item 12.5 x 20 Lead wire diameter d Body height A Intervals of bodies P Intervals of punched holes P0 Distance between holes and lead wire P1 Distance between holes and bodies Distance between lead and lead Base tape width Adhesive tape width Deviation between holes and base tape Deviation between adhesive and base tape Case Size Symbol 12.5 x 25 12.5 x 30 16 x 25 16 x 31.5 0.6 21.5 26.5 16 x 35.5 18 x 35.5 0.8 31.5 26.5 15.0 33 37.0 37.0 3.75 5.0 ±0.7 ±1.0 +0.8 -0.2 7.5 W W0 18.0 ±0.5 15.0 MIN W1 9.0 ±0.5 W2 1.5 MAX Distance between body bottom and tape center H Distance between body top and tape center H1 Punched hole diameter D0 4.0 ±0.3 Length of not good lead slit L 11.0 MAX t 0.6 ±0.3 ∆h 0 ±2.0 ∆h1 0 ±1.0 Base and adhesive tape thickness Deviation of body alignment Deviation of body alignment 16.5 40.5 45.5 18.5 50.5 46.5 Fig 5. Fig 6. ±0.2 7.5 F MAX ±1.0 15.0 P2 Remark ±0.05 30.0 5.0 Tolerance 53.5 ±0.5 56.5 56.5 Fig 5. Fig 6. MAX Rev. 7a Aluminum Electrolytic Capacitors MI Series (85°C,7mmL) MERITEK Rev. 7a Aluminum Electrolytic Capacitors MI Series (85°C,7mmL) MERITEK SOLDERABILITY Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the liquid solder 2mm, the dipping lead must be adherent 95% fresh tin at least. RESISTANCE TO SOLDERING HEAT Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room temperature, should do final measurements, the values are following: (A) Capacitance change: ≦ ±10% of initial value (B) Dissipation factor: ≦ initial specified value (C) Leakage current: ≦ initial specified value (D) Visual: No damage Rev. 7a