MIL-PRF-38534 AND 38535 CERTIFIED FACILITY
M.S.KENNEDY
CORP.
M.S.
KENNEDY
CORP.
4354
10 AMP, 600 VOLT IGBT
SMART POWER 3-PHASE
MOTOR DRIVE HYBRID
4707 Dey Road Liverpool, N.Y. 13088
(315) 701-6751
FEATURES:
600V,10 Amp Capability
Ultra Low Thermal Resistance - Junction to Case - 1.35°C/W (Each IGBT)
Self-Contained, Smart Lowside/Highside Drive Circuitry
Bootstrap High-Side Supplies
Under-Voltage Lockout
Capable of Switching Frequencies to 25KHz
Isolated Case Allows Direct Heat Sinking
Bolt-down Design Allows Superior Heat Dissipation
Contact MSK for MIL-PRF-38534 Qualification Status
DESCRIPTION:
The MSK 4354 is a 10 Amp, 3 Phase Bridge Smart Power Motor Drive Hybrid with a 600 volt rating on the output
switches. The output switches are Insulated Gate Bipolar Transistors (IGBT's). The free-wheeling diodes are Fast
Recovery Epitaxial Diodes (FRED's) to provide matched current capabilities with the IGBT's and are specified with excellent reverse recovery times. This new smart power motor drive hybrid is 5.0 volt input logic compatible. Under-voltage
lockout shuts down the bridge when the supply voltage gets to a point of incomplete turn-on of the output switches. The
internal high-side bootstrap power supply derived from the +VB supply completely eliminates the need for 3 floating
independent power supplies.
EQUIVALENT SCHEMATIC
PIN-OUT INFORMATION
TYPICAL APPLICATIONS
TYPICAL APPLICATIONSPIN-OUT INFORMATION
3 PHASE SIX STEP DC BRUSHLESS MOTOR DRIVE
OR 3 PHASE SINUSOIDAL INDUCTION MOTOR DRIVE
1
1
2
3
4
5
6
7
8
9
10
H INA
L INA
+VCC
H INB
L INB
COM
COM
+VB
H INC
L INC
20
19
18
17
16
15
14
13
12
11
V+
N/C
AVAØ
N/C
BVBØ
N/C
CVCØ
8548-73 Rev. J 10/13
6
ABSOLUTE MAXIMUM RATINGS
V+
VCC
IOUT
IPK
θJC
θJC
High Voltage Supply 7
600V
Logic Supply
18V
Continuous Output Current
10A
Peak Output Current
30A
Thermal Resistance @ 125°C
(Output Switches)(Junction to Case) 1.35°C/W
Thermal Resistance @ 125°C
(Diodes)
1.7°C/W
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TsT Storage Temperature Range 8
TLD Lead Temperature Range
TC (10 Seconds)
Case Operating Temperature
MSK 4354
MSK 4354H
TJ Junction Temperature
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
300°C
-40°C to +85°C
-55°C to +125°C
+150°C
○
○
○
-65° to +150°C
○
○
○
○
○
○
○
ELECTRICAL SPECIFICATIONS
Parameters
Test Conditions
GROUP A
MSK 4354H 3
SUBGROUP
Min. Typ. Max.
5
MSK 4354 2
UNITS
Min. Typ. Max.
OUTPUT CHARACTERISTICS
VC-E (On) Voltage (Each IGBT)
Leakage Current (Each IGBT)
Instantaneous Forward Voltage
(FRED Flyback Diode)
Ic=10A
V+ = 600V
V+ = 500V
V+ = 480V
ID=10A
Reverse Recovery Time 1 ID=10A, di/dt=100A/μS, Vr=350V
BIAS SUPPLY CHARACTERISTICS
+VCC Bias Current
+VCC=15V
+VB Bias Current
+VB=15V
INPUT SIGNAL CHARACTERISTICS 1
Positive Trigger Threshold Voltage
+VCC=15V
Negative Trigger Threshold Voltage
+VCC=15V
+VCC Positive Going Threshold
Under-voltage Lockout
+VCC Negative Going Threshold
Low Side Turn-off to High Side Turn-On
Dead Time
High Side Turn-off to Low Side Turn-On
1
2
3
1
2
3
1
2
3
-
-
3.1
2.6
3.5
250
1.75
3
1.9
1.8
1.9
-
3.8
3.5
4.0
500
2.5
7.0
2.5
2.5
2.5
180
-
1
2
3
1
2
3
-
-
6
8
6
1
2
1
-
1,2,3
1,2,3
-
2.7
7.2
6.7
280
280
8.9
8.2
400
400
0.8
10.8
9.9
520
520
3.2 3.9
250 600
2.0 2.6
180
-
6
1
-
2.7
0.8
7.2 8.9 10.8
6.7 8.2 9.9
280 400 520
280 400 520
volts
volts
volts
μA
mA
mA
volts
volts
volts
nS
mA
mA
mA
mA
mA
mA
volts
volts
volts
volts
nSEC
nSEC
NOTES:
1
2
3
4
5
6
7
8
Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.
Military grade devices ("H" suffix) shall be 100% tested to subgroups 1, 2, 3 and 4.
Subgroups 5 and 6 testing available upon request.
Subgroup
1, 4 TA = TC = +25°C
2, 5 TA = TC = +125°C
3, 6 TA = TC = -55°C
Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle.
When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the same time.
Do not apply high voltage without low voltage present.
Internal solder reflow temperature is 180°C, do not exceed.
2
8548-73 Rev. J 10/13
TYPICAL PERFORMANCE CURVES
3
8548-73 Rev. J 10/13
APPLICATION NOTES
MSK 4354 PIN DESCRIPTIONS
+VCC - Is the low voltage supply for all the internal
logic and drivers. A 0.1 μF ceramic capacitor in parallel with a 10μF tantalum capacitor is the recommended
bypassing from the +VCC pin to the COM pin.
H INA, H INB, H INC - Are high active logic inputs for
signalling the corresponding phase high-side switch to
turn on. The logic inputs are compatible with standard
CMOS or LSTTL outputs. These logic inputs are internally zener clamped at 5.2 volts.
L INA, L INB, L INC - Are low active logic inputs for
signalling the corresponding phase low-side switch to
turn on. The logic inputs are compatible with standard
CMOS or LSTTL outputs. These logic numbers are
internally zener clamped at 5.2 volts.
AØ, BØ, CØ - Are the pins connecting the 3 phase
bridge switch options.
AV-, BV-, CV- - Are the connections from the bottoms
of the three half bridges. These pins get connected to
the COM pin. If current sensing is desired they may be
connected to the COM pin through a low value sense
resistor.
+VB - Is the connection used to provide power to the
floating high-side bootstrap supplies in the gate drive
circuitry.
V+ - Is the high voltage positive rail connection to the
tops of the three half bridges. Proper power supply
bypassing must be connected from this pin to the COM
pin for good filtering. This bypassing must be done as
close to the hybrid as possible.
COM - Is the connection that all hybrid power supply
connections are returned to and bypassed to.
4
8548-73 Rev. J 10/13
TYPICAL SYSTEM OPERATION
The MSK 4354 is designed to be used with a +270 volt high voltage bus, +15 volt low power bus and +5 volt
logic signals. Proper derating should be applied when designing the MSK 4354 into a system. High frequency layout
techniques with ground planes on a printed circuit board is the only method that should be used for circuit construction. This will prevent pulse jitter caused by excessive noise pickup on the current sense signal or the error amp
signal.
Ground planes for the lower power circuitry and the high power circuitry should be kept separate. The connection
between the bottom of the current sense resistor, COM pin and the high power ground, AV-, BV- and CV- pins are
connected at this point. This is a critical path and high currents should not be flowing between the current sense and
COM. Inductance in this path should be kept to a minimum. An RC filter (shown in 2 places) will filter out the current
spikes and keep the detected noise for those circuits down to a minimum.
In the system shown a PWM pulse by pulse current limit scheme controlled by the motor controller is implemented.
When controlling the motor speed by the PWM method, it is required that the low side switches be PWM pulsed due
to the bootstrap supplies used to power the high side switch drives. The higher the PWM speed the higher the current
load on the drive supply. PWM of the low side will prevent sagging of the high side supplies. A separate pin (+VB)
is provided for connecting an external floating power supply to power the bootstrap supplies.
5
8548-73 Rev. J 10/13
MECHANICAL SPECIFICATIONS
Weight=42 Grams Typical
Contains Internal BeO (Beryllium Oxide)
All dimensions are ±0.01 inches unless otherwise specified.
ESD Triangle Indicates Pin 1
ORDERING INFORMATION
MSK4354 H U
LEAD CONFIGURATIONS
S=STRAIGHT; U=BENT UP; D=BENT DOWN
SCREENING
BLANK=INDUSTRIAL; H=MIL-PRF-38534 CLASS H
GENERAL PART NUMBER
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751
FAX (315) 701-6752
www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however and assumes no liability for the use of its products.
Please visit our website for the most recent version of this datasheet.
Contact MSK for MIL-PRF-38534 qualification status.
6
8548-73 Rev. J 10/13