MSK4201 - M.S. Kennedy Corp.

MIL-PRF-38534 AND 38535 CERTIFIED FACILITY
M.S.KENNEDY CORP.
75 VOLT 5 AMP MOSFET
H-BRIDGE PWM MOTOR
DRIVER/AMPLIFIER
4201
FEATURES:
Low Cost Complete H-Bridge
28 Volt, 5 Amp Capability, 75 Volt Maximum Rating
Self-contained Smart Lowside/Highside Drive Circuitry
Internal Deadtime Generation, Shoot-through Protection
Output Disable/Shutdown Capability
Isolated Case Allows Direct Heatsinking
Four Quadrant Operation, Torque Control Capability
Available Fully Screened and Qualified to MIL-PRF-38534
Replaces SA-51
Available to DLA SMD 5962-97629
DESCRIPTION:
The MSK4201 is a complete H-Bridge MCM to be used for DC brushed motor control or Class D switchmode amplifier.
All of the drive/control circtuitry for the lowside and highside switches are internal to the MCM . The user provides a TTL
compatible PWM signal for simultaneous amplitude and direction control in four quadrant mode. The internal drive circuitry
will provide proper deadtime/shoot-through protection for each half-bridge. All N-channel FETs mean the best efficiency for
the size, both in terms of on-resistance and switching capability. For an idle/sleep mode, or for fault protection, a TTL
compatible disable pin is provided so as to shut down all four transistors. The MSK4201 is packaged in a space efficient
isolated 8 pin TO-3 that can be directly connected to a heatsink.
EQUIVALENT SCHEMATIC
PIN-OUT INFORMATION
TYPICAL APPLICATIONS
1
2
3
4
1
V+
MOTOR B
VCC
DISABLE
5
6
7
8
GND
INPUT
MOTOR A
RSENSE
8548-116 Rev. F 3/14
6
ABSOLUTE MAXIMUM RATINGS
V+
VCC
IOUT
IPK
VOUT
θJC
75V
High Voltage Supply 7
16V
Logic Supply
5A
Continuous Output Current
37A
Peak Output Current
Output Voltage Range GND-2V min. To V+ max.
2.3°C/W
Thermal Resistance @ 125°C Case
(Output Switches)
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TST
TLD
○
TC
○
○
○
○
Test Conditions
8
○
○
○
TJ
ELECTRICAL SPECIFICATIONS
Parameter
Storage Temperature Range
Lead Temperature Range
(10 Seconds)
Case Operating Temperature
MSK4201
MSK4201B
Junction Temperature
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
-65°C to +150°C
○
○
○
○
○
○
○
300°C
-40°C to +125°C
-55°C to +125°C
+175°C
○
○
○
○
○
All Ratings: Tc= +25°C Unless Otherwise Specified
Subgroup
Group A
MSK4201B 3
MSK4201 2
Units
5
Min.
Typ.
Max.
Min.
Typ.
Max.
1
-
1.5
1.8
-
1.5
2.16
V
2
-
2.2
2.4
-
-
-
V
V
OUTPUT CHARACTERISTICS
VDS(ON) Voltage (Each MOSFET)
ID=5A
Instantaneous Forward Voltage, Each MOSFET IS=5A 1
(Intrinsic Diode)
Reverse Recovery Time (Intrinsic Diode) 1
Leakage Current, Each MOSFET
3
-
1.1
1.2
-
-
-
1
-
1.0
2.1
-
1.0
2.2
V
2
-
0.9
2.0
-
-
-
V
3
-
1.1
2.2
-
-
-
V
nS
-
-
-
240
-
-
240
V+=70V
1
-
-
25
-
-
30
uA
V+=70V
2
-
-
250
-
-
-
uA
V+=70V
3
-
-
25
-
-
-
uA
-
10
12
15
10
12
15
V
VCC=12V
1
-
11
18
-
11
21
mA
(non-switching)
2
-
11
18
-
-
-
mA
mA
VCC SUPPLY CHARACTERISTICS
VCC Supply Voltage Range 1
Quiescent Logic Current
3
-
11
18
-
-
-
1,2,3
0.8
1.5
2.7
0.8
1.5
2.7
V
Turn-On Propagation Delay (Includes Deadtime)
-
-
160
240
-
160
-
nS
Turn-Off Propagation Delay
-
-
85
128
-
85
-
nS
Rise-Time
-
-
36
54
-
36
-
nS
Fall-Time
-
-
170
255
-
170
-
nS
nS
-
INPUT SIGNALS CHARACTERISTICS
Threshold Voltage
1
SWITCHING CHARACTERISTICS 1
VCC=12V
V+=28V, VCC=12V, IC=2A
Dead-Time
Disable Function
DIS>3.6V
-
-
100
-
-
100
-
7
-
P/F
-
-
P/F
-
dis
NOTES:
1
2
3
4
5
6
7
8
9
Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
Industrial grade devices shall be tested to subgroup 1 unless otherwise specified.
Military grade devices ("B" suffix) shall be 100% tested to subgroups 1,2,3 and 7.
Subgroups 5 and 6 testing available upon request.
Subgroup 1,4 TA=TC= +25°C
2
TA=TC= +125°C
3
TA=TC= -55°C
Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the
same time. Do not apply high voltage without low voltage present.
Internal solder reflow temperature is 180°C, do not exceed.
Reference DLA SMD 5962-97629 for electrical specification for devices purchased as such.
2
8548-116 Rev. F 3/14
APPLICATION NOTES
MSK4201 PIN DESCRIPTION
VCC - Is the low voltage supply for powering internal
logic and drivers for the lowside and highside MOSFETS.
The supplies for the highside drivers are derived from
this voltage.
V+ - Is the higher voltage H-bridge supply. The MOSFETS
obtain the drive current from this supply pin. The voltage
on this pin is limited by the drive IC. The MOSFETS are
rated at 100 volts. Proper by-passing to GND with sufficient capacitance to suppress any voltage transients, and
to ensure removing any drooping during switching, should
be done as close to the pins on the hybrid as possible.
MOTOR A - Is the output pin for one half of the bridge.
When the PWM input is high, this output will be pulled
up to V+.
MOTOR B - Is the output pin for the other half of the
bridge. When the PWM input is low, this output will be
pulled up to V+.
IN
RSENSE - This is the common connection for the bottom of the bridge. This can have a sense resistor connection to the V+ return ground for current limit sensing, or
can be connected directly to ground. The maximum voltage on this pin is ±2 volts with respect to GND.
GND - Is the return connection for the input logic and
Vcc.
PWM INPUT - Is a TTL compatible input pin for providing the PWM signal to modulate the output switches.
The duty cycle can be between 0% (DC Low) and 100%
(DC High). See typical system operation notes.
DISABLE INPUT - Is a TTL compatible input for providing a shutdown signal to the MCM for disabling all four
switches in the bridge regardless of the PWM input level.
A digital 1 disables, a digital 0 enables.
3
8548-116 Rev. F 3/14
TYPICAL SYSTEM OPERATION
This is a diagram of a typical application of the MSK4201. The design Vcc voltage is +12 volts and should have a good low ESR
bypass capacitor such as a tantalum. The PWM and DISABLE signals are typically provided by some type of microprocessor control.
The PWM signal will be a TTL signal with a pulse frequency required by the system, and pulse duty cycles according to the required
direction/speed. A 0% duty cycle (continuous TTL low) will mean full voltage to the motor in one direction. A 100% duty cycle
(continuous TTL high) will mean full voltage to the motor in the other direction. A 50% duty cycle will hold the motor at 0 RPM.
Current sensing is done in this case by a 0.1 ohm sense resistor to sense current from either leg of the bridge. It is important to
make the high current traces as wide as possible to keep inductance down. The storage capacitor connected to the V+ and the hybrid
should be large enough to provide the high energy pulse without the voltage sagging too far. The storage capacitor should be a low
ESR ceramic capacitor or large polypropylene capacitor. Mount capacitor as close to the MCM as possible. The connection between
GND and the V+ return should not be carrying any motor current. The sense resistor signal is common mode filtered as necessary to
feed the limiting circuitry for the microprocessor. This application will allow full four quadrant torque control for a closed loop servo
system.
A snubber network is usually required, due to the inductance in the power loop. It is important to design the snubber network to
suppress any positive spikes above 75V and negative spikes below -2V with respect to pin 5 (gnd) of the MCM.
4
8548-116 Rev. F 3/14
MECHANICAL SPECIFICATIONS
ALL DIMENSIONS ARE SPECIFIED IN INCHES
WEIGHT= 15.2 GRAMS TYPICAL
ORDERING INFORMATION
Part
Number
Screening Level
MSK4201
Industrial
MSK4201B
Mil-PRF-38534 Class H
5
8548-116 Rev. F 3/14
REVISION HISTORY
M.S. Kennedy Corp.
Phone (315) 701-6751
FAX (315) 701-6752
www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
6
8548-116 Rev. F 3/14