DATA SHEET CLL030-1206A1-403M1A2

DATA SHEET
CLL030-1206A1-403M1A2
and
are trademarks or registered trademarks of CITIZEN HOLDINGS CO., LTD. JAPAN.
is a trademark or a registered trademark of CITIZEN ELECTRONICS CO., LTD. JAPAN.
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
1/11
1. Scope of Application
This data sheet is applied to the LED package, model CLL030-1206A1-403M1A2.
2. Part code
CLL 030 - 12 06 A1 - 40 3 M1 A2
[1]
[2] [3]
[4]
[5]
[6]
[1] Part Code
[2] Dies in series quantity
[3] Dies in parallel quantity
[4] Correlated color temperature
[5] Chromaticity range
[6] CRI
< Features >
- External Dimensions: 19.0×19.0×1.4 mm
- Internal Structure: Aluminum Base Chip on Board
- Connection to Heat Sink: By M3 screw (Recommended)
- Luminous Flux: 1390 lm @ 360 mA
- CCT: 4000 K (ANSI C78.377 Compliant, in 3-Step MacAdam Ellipse)
- CRI: Ra 80 min.
- Thermal Resistance: 1.5 C/W
- RoHS Compliant
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
2/11
3. Outline drawing - Marking
Unit : mm
Tolerances unless otherwise specified : +/-0.3
Protection device
Anode
Marking 1
×12
×12
Anode
×12
×12
Cathode
×12
Cathode
(Tc Measurement Point)
×12
Marking 2
Marking 1 : Serial No.
Marking 2 : 12 06 40 M1
CRI : Ra 80min.
Correlated color temperature : 4000K
Dies in parallel quantity : 6
Dies in series quantity : 12
4. Performance
(1) Absolute Maximum Rating
Parameter
Symbol
Rating Value
Unit
Input Power
32.1
*1
Pi
W
IF
mA
Forward Current
720
*1
IR
mA
Reverse Current
1
Top
-30 ~ +85
C
Operating Temperature
Tst
-40 ~ +100
C
Storage Temperature
Case Temperature
100
*2
Tc
C
Junction Temperature
Tj
150
C
*3
*1 Input power and forward current are the values when the LED is used within the range of
the derating curve in this data sheet.
*2 Refer to 3. Outline drawing for Tc measurement point
*3 D.C. Current : Tj = Tc + Rj-c X Pi
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
3/11
(2) Electro-optical Characteristics
Parameter
Forward Voltage
Luminous Flux
CRI
Thermal Resistance
Symbol
VF
Condition
IF=360 mA
IF=360 mA
IF=360 mA
Φv
Ra
Rj-c
Junction-Case
Min.
33.6
1180
80
-
Typ.
36.6
1390
1.5
Max
39.9
-
Tc=25C
Unit
V
lm
C/W
Chromaticity coordinates ( Condition : IF=360mA, Tc = 25C)
Center
x
y
0.3818
0.3797
Oval parameter
a
0.00939
b
0.00402
θ°
54.00
Reference (ANSI C78.377)
x
Center 0.3818
a
0.4006
4000K
b
0.3736
c
0.3670
d
0.3898
y
0.3797
0.4044
0.3874
0.3578
0.3716
*Color region stay within MacAdam "3-step" ellipse from the chromaticity center.
*The chromaticity center refers to ANSI C78.377:2008.
Please refer to ANSI C78.377 for the chromaticity center.
*θ is the angle between the major axis of the ellipse and the x-axis,
and a and b are the major and minor semi-axes of an ellipse. (Ref. IEC 60081:1997 AnnexD)
x-y chart-CIE1931
0.41
4400K
3600K
4000K
0.40
Color region
y
0.39
Color region
(ANSI)
0.38
B.B. Locus
0.37
0.36
4200K
3800K
0.35
0.36
0.37
0.38
x
0.39
0.40
0.41
Note: The tolerance of measurement at our tester is VF+/-3% , Φv+/-10% , Chromaticity(x,y)+/-0.005 and Ra+/-1.
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
4/11
5. Characteristics
40.0
38.0
VF [V]
Forward Current vs. Relative Luminous Flux
Tc=25C
200%
180%
160%
140%
120%
100%
80%
60%
40%
20%
0%
0
200
400
600
800
Relative Luminous Flux [a.u.]
Forward Current vs. Forward Voltage
Tc=25C
42.0
36.0
34.0
32.0
30.0
0
200
400
600
800
IF [mA]
IF [mA]
Forward Current vs. Chromaticity Coordinate
Tc=25C
0.020
Δx
0.015
Δy
0.005
△x, △y
△x, △y
0.010
Case Temperature vs. Chromaticity Coordinate
IF=360mA
0.020
Δx
0.015
Δy
0.010
0.000
-0.005
0.005
0.000
-0.005
-0.010
-0.010
-0.015
-0.015
-0.020
-0.020
0
200
400
600
800
0
25
50
75
100
Tc [C]
IF [mA]
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
Case Temperature vs. Forward Voltage
IF=360mA
39.0
Case Temperature vs. Relative Luminous Flux
IF=360mA
120%
100%
Relative Luminous Flux [a.u.]
38.0
37.0
VF [V]
5/11
36.0
35.0
34.0
80%
60%
40%
20%
33.0
0%
0
25
50
75
100
0
25
Case Temperature vs. Allowable Forward Current
700
IF [mA]
600
500
400
300
200
100
0
50
75
100
Spectrum
Relative Emission Intensity [a.u.]
800
25
75
Tc [C]
Tc [C]
0
50
100
125
Tc=25C IF=360mA
120%
100%
80%
60%
40%
20%
0%
350
450
550
650
750
850
λ [nm]
Tc [C]
Directive Characteristic
-40°
-30° -20° -10°
100%
10° 20° 30°
40°
-50°
50°
80%
Y
-60°
60%
60°
-70°
40%
70°
-80°
20%
-90°
0%
X
80°
X direction
Y direction
90°
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
6/11
6. Reliability
(1)Datails of the tests
Test Item
Test Condition
Ta=25 C, IF=360 mA× 1000 hours(with Al-fin)
Continuous Operation Test
IF=360 mA Tjmax=150C× 1000 hours(with Al-fin)
Low Temperature Storage Test -40 C × 1000 hours
High Temperature Storage Test 100 C × 1000 hours
Moisture-proof Test
85 C, 85 %RH for 500 hours
Thermal Shock Test
-40 C × 30 minutes – 100 C × 30 minutes, 100 cycle
(2)Judgement Criteria of Failure for Reliability Test
(Ta=25C)
Measuring Item
Forward Voltage
Total Luminous Flux
Symbol
VF
Φv
Measuring Condition
IF=360 mA
IF=360mA
Judgement Criteria for Failure
>U X 1.1
<S X 0.85
U defines the upper limit of the specified characteristics. S defines the initial value.
Note : Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be
return to the normal ambient conditions after the completion of each test.
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
7/11
7. Packing Specifications
(1) Packing
An empty tray is placed on top of a six-tier tray which contain 48 pieces each. The set of seven
trays is banded together with two rubber bands.
(Smallest packing unit: 288 pieces)
A label with product name, quantity, lot number is placed on the upper empty tray.
Tray (Dimensions: 310 × 210 × 12 mm / Materials: Electrically conductive PS)
< Packing figure >
Product 48pcs/tray
< Example of indication label >
CUSTOMER
TYPE : CLL030-******-*******
---(1)
P. NO : ******
---(2)
Lot No: *******
---(3)
Q'ty : ***
---(4)
CITIZEN ELECTRONICS
PASS
1. TYPE
e.g. CLL030-1206A1-403M1A2
2. P.No. (Cutomer's P/N)
e.g. 50008-010-1203303M1
3. Lot No.
- First and second letter: Last digit of the year e.g. 11 : year 2011
- Third letter: Production month
e.g. 8 : August
Note: October, November and December are designated
- Forth letter: CE's control number
e.g. 5035
4. Quantity
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
8/11
8.Precautions
(1) 1. Handling with care for this product
-Both the light emitting area and white dam over the light emitting area is composed of resin materials.
Please avoid the resin area from being pressed, stressed, rubbed, come into contact with sharp metal nail
(e.g. edge of reflector part) because the function, performance and reliability of this product
are negatively impacted.
-Please be aware that this product should not come into contact with any other parts
while incorporating in your lighting apparatus or your other products.
Emitting area (including white resin)
(2) Countermeasure against static electricity
-Handling of this product needs countermeasures against static electricity
because this is a semiconductor product.
-Please take adequate measures to prevent any static electricity being produced
such as the wearing of a wristband or anti-static gloves when handling this product.
-Every manufacturing facility in regard to the product (plant, equipment, machine, carrier machine
and conveyance unit) should be connected to ground and please avoid the product to be electric-charged.
-ESD sensitivity of this product is over 1000V (HBM, based on JEITA ED-4701/304).
-After assembling the LEDs into your final product(s), it is recommended to check
whether the assembled LEDs are damaged by static electricity (electrical leak phenomenon) or not.
-It is easy to find static damaged LED dies by a light-on test with the minimum current value.
(3) Caution of product assembly
-Regarding this product assembling on the heat sink, it is recommended to use M3 screw.
It might be good for screw tightening on the heat sink to do temporary tightening and final tightening.
In addition, please don’t press with excess stress on the product.
-The condition of the product assembling on the heat sink and the control of screw tightening torque
needs to be optimized according to the specification of the heat sink.
-Roughness, unevenness and burr of surface negatively impact thermal bonding
between the product and heat sink and increase heat thermal resistance between them.
Confidence of thermally and mechanical coupling between the product and heat sink are confirmed
by checking the mounting surface and measuring the case temperature of the product.
-In order to reduce the thermal resistance at assembly, it might be good to use
TIM (Thermal Interface Material) on whole contact surface of the product.
In case of using thermal grease for the TIM, it might be good to be applied uniformly
on the contact surface of the product. In case of using thermal sheet for the TIM,
it might be good to make sure that the product is NOT strained by stress
when the screws are tightened for assembly.
M3screw
Spring Washer (=< Φ6mm)
19.0
Plane washer (=< Φ6mm)
Thermal Interface materials
(Insulation)
19.0
Outer heart sink
Recommended installation screw pitch
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
9/11
8. Precautions (continued)
(4) Thermal Design
-The thermal design to draw heat away from the LED junction is most critical parameter
for an LED illumination system. High operating temperatures at the LED junction adversely affect
the performance of LED’s light output and lifetime. Therefore the LED junction temperature should
not exceed the absolute maximum rating in LED illumination system.
(Note : Refer to 4-(1) Performance)
-The LED junction temperature while operation of LED illumination system depends upon
thermal resistance of internal LED package (Rj-c), outer thermal resistances of LED package,
power loss and ambient temperature. Please take both of the thermal design specifications
and ambient temperature conditions into consideration for the setting of driving conditions.
-For more information, please refer to application note "Thermal Management CLL030 Series".
(5) Driving Current
-A constant current is recommended as an applying driving current to this product.
In the case of constant voltage driving, please connect current-limiting resistor to each products in series
and control the driving current to keep under the absolute maximum rating forward current value.
-Electrical transient might apply excess voltage, excess current and reverse voltage to the product(s).
They also affect negative impact on the product(s) therefore please make sure that no excess voltage,
excess current and reverse voltage is applied to the product(s)
when the LED driver is turn-on and/or turn-off.
-For more information, please refer to application note "Driving".
(6) Lighting at a minimum current value
- The minimum current value of all LED dice lighting is 30 mA.
(The minimum current of each product is calculated and stated on the premise of 5mA dice)
-In a case where the lowest current is applied to the product,
some of LED dice in the product might look different in their brightness
due to the individual difference of the LED dice, and they are not failed.
(7) Electrical Safety
-This product is designed and produced according to IEC 62031:2008
(IEC 62031:2008 LED modules for general lighting. Safety specification)
-Dielectric voltage withstand test has been conducted on this product to see any failure
after applying voltage between active pads and aluminum section of the product,
and to pass at least 500V.
-Considering conformity assessment for IEC62031:2008, almost all items of the specification
depend upon your final product of LED illumination system.
Therefore, please confirm with your final product for electrical safety of your product.
As well, the products comply with the criteria of IEC62031:2008 as single LED package.
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
10/11
8. Precautions (continued)
(8) Recommended soldering Condition (This product is not adaptable to reflow process.)
-For manual soldering
Please use lead-free soldering.
Soldering shall be implemented using a soldering bit at a temperature lower than 350C°,
and shall be finished within 3.5 seconds for one land.
No external force shall be applied to resin part while soldering is implemented.
Next process of soldering should be carried out after the product has return to ambient temperature.
-For soldering correction
Regarding soldering correction, above conditions shall be applied.
Contacts number of soldering bit should be within twice for each terminal as a correction.
* Citizen Electronics cannot guarantee if usage exceeds these recommended conditions.
Please use it after sufficient verification is carried out on your own risk if absolutely necessary.
(9) Eye Safety
-The International Electrical Commission (IEC) published in 2006 IEC 62471
”2006 Photobiological safety of lamps and lamp systems ” which includes LEDs within its scope.
When sorting single LEDs according to IEC 62471, almost all white LEDs can be classified
as belonging to either Exempt Group (no hazard) or Risk Group 1 (low risk).
-However, Optical characteristics of LEDs such as radiant flux,
spectrum and light distribution are factors that affect the risk group determination of the LED,
and especially a high-power LED, that emits light containing blue wavelengths,
might have properties equivalent to those of Risk Group 2 (moderate risk).
-Great care should be taken when directly viewing an LED that is driven at high current,
has multiple uses as a module or when focusing the light with optical instruments,
as these actions might greatly increase the hazard to your eyes.
-It is recommended to regard the evaluation of stand-alone LED packages as a reference
andThis
to evaluate
product.
(10)
product your
is notfinal
designed
for usage under the following conditions.
If the product might be used under the following conditions, you shall evaluate its effect
and appropriate them. In places where the product might:
-directly and indirectly get wet due to rain and/or at place with the fear.
-be damage by seawater and/or at place with the fear
-be exposed to corrosive gas (such as Cl2, H2S, NH3, SOx, NOx and so on) and/or at place with the fear.
-be exposed to dust, fluid or oil and/or at place with the fear.
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)
DATA SHEET
11/11
9. Precautions with regard to product use
(1) This document is provided for reference purposes only so that CITIZEN ELECTRONICS'
products are used as intended. CITIZEN ELECTRONICS neither makes warranties or
representations with respect to the accuracy or completeness of the information contained
in this document nor grants any license to any intellectual property rights or any other
rights of CITIZEN ELECTRONICS or any third party with respect to the information
in this document.
(2) All information included in this document such as product data, diagrams, charts,
is current as of the date this document is issued.
Such information, however, is subject to change without any prior notice.
Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document,
please confirm the latest product information with a CITIZEN ELECTRONICS' sales office,
and formal specifications must be exchanged and signed by both parties prior to mass production.
(3) CITIZEN ELECTRONICS has used reasonable care in compiling the information
included in this document,
but CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as
a result of errors or omissions in the information included in this document.
(4) Absent a written signed agreement, except as provided in the relevant terms and conditions of
sale for product, and to the maximum extent allowable by law, CITIZEN ELECTRONICS
assumes no liability whatsoever, including without limitation, indirect, consequential, special,
or incidental damages or loss, including without limitation, loss of profits, loss of opportunities,
business interruption and loss of data, and disclaims any and all express or implied warranties
and conditions related to sale, use of product, or information, including warranties
or conditions of merchantability, fitness for a particular purpose, accuracy of information,
or no infringement.
(5) Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability,
products can malfunction or fail. Customers are responsible for complying with safety standards
and for providing adequate designs and safeguards to minimize risk and avoid situations
in which a malfunction or failure of a product could cause loss of human life,
bodily injury or damage to property, including data loss or corruption.
In addition, customers are also responsible for determining the appropriateness of
use of any information contained in this document such as application cases not only with
evaluating by their own but also by the entire system.
CITIZEN ELECTRONICS assumes no liability for customers' product design or applications.
(6) Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding
the information contained in this document, or if you have any other inquiries.
CITIZEN Micro HumanTech is a registered trademark of Citizen Holding Co., Japan.
CITILED is a registered trademark of CITIZEN ELECTRONICS CO., LTD. Japan
Symbol
CITILED
Name
CLL030-1206A1-403M1A2
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Ref.CE-P1946 02/12 R1(0612)