Monolithic Crystal Filters (M.C.F.) MERCURY Since 1973 MCF (MONOLITHIC CRYSTAL FILTER) features high quality quartz resonators such as sharp cutoff characteristics, low loss, good inter-modulation and high stability over wide temperature range. Consideration in applying band pass filters to communication systems. TECHNICAL TERMS INSERTION LOSS: The loss at center frequency, normally expressed in dB, resulting from the insertion of a device in a transmission system. FLAT LOSS: The insertion loss at the frequency of minimum loss within the pass band. ATTENUATION: The loss of a filter at a given frequency measured in dB. PASSBAND (BW): The range of frequencies attenuated less than a specified value, typically 3 or 6 dB. CENTER FREQUENCY (F0): FRACTIONAL BANDWIDTH: The ratio of the pass band to the center frequency. STOPBAND: The range of frequencies attenuated greater than some specified minimum level of attenuation. TRANSITION BAND (Bwt): The range of frequencies differentially attenuated between the pass band and stop band limits. SHAPE FACTOR: The ratio of the bandwidth at some point within the transition region typically 60 dB, to the specified pass band bandwidth. SPURIOUS ATTENUATION: The specified minimum level of attenuation received by all non harmonic related resonance of each crystal; resonator within the filter network. REFERENCE FREQUENCY: A specified frequency, typically the minimum loss point or F0, from which all attenuation measurements are made. RIPPLE: The amplitude difference, in dB, between the maximum pass band peak and maximum pass band valley are defined by a surrounding change in slope, I.E. sign of the amplitude response. ATTENUATION: The output of a filter at a given frequency relative to the defined insertion loss reference. MERCURY www.mercury-crystal.com Taiwan: TEL (886)-2-2695-7099, FAX (886)-2-2695-7473, e-mail: [email protected] U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected] MERCURY Page 1 of 6 Date: Dec. 1, 2001 Rev. 0 Monolithic Crystal Filters MCF 10.7 MHz Family Channel Spacing (kHz) 12.5 20 25 50 Model Operating Temperature Range: -10 to +70°C Pass Band No. Stop Band Width Width of (max.) (min.) Poles dB kHz MERCURY Since 1973 10.7 MHz dB kHz Ripple dB kHz dB max Insertion Guaranteed Loss Attenuation dB max dB ( fo ± kHz) Terminating Impedance (ohms // pF) Package 1.8K // 5.0 HC49T 10M07A 2 3 ±3.75 20 ±18 - - 0.5 1.5 35 +300 to +1000 50 -200 to –1000 10M07B 4 3 ±3.75 40 ±14 - - 1.0 2.5 65 +300 to +1000 80 -200 to –1000 1.8K // 4.5 Zc: 11.0 pF HC49Tx2 (a pair) 10M07C 6 3 ±3.75 45 ±8.75 65 ±12.5 2.0 3.5 65 12.5 to 300 1.8K // 3.5 L-1 10M07D 8 3 ±3.75 65 ±8.75 90 ±12.5 2.0 4.0 90 12.5 to 300 1.8K // 3.5 L-2 10M09A 2 3 ±6.0 18 ±23 - - 0.5 2.0 35 +300 to +1000 40 -200 to –1000 2.5K // 2.5 HC49T 10M09B 4 3 ±6.0 40 ±20 - - 1.0 2.5 65 +300 to +1000 80 -200 to –1000 2.5K // 1.5 Zc: 6.0 pF HC49Tx2 (a pair) 10M09C 6 3 ±6.0 45 ±14 60 ±20 2.0 3.0 65 20 to 300 2.8K // 1.0 L-1 10M09D 8 3 ±6.0 65 ±14 90 ±20 2.0 4.0 90 20 to 300 2.8K // 1.0 L-2 10M15A 2 3 ±7.5 18 ±25 - - 0.5 2.0 35 +300 to +1000 40 -200 to -1000 3.0K // 2.0 HC49T 10M15B 4 3 ±7.5 40 ±25 - - 1.0 2.5 55 +300 to +1000 80 -200 to -1000 3.0K // 2.0 Zc: 5.0 pF HC49Tx2 (a pair) 10M15C 6 3 ±7.5 45 ±17.5 65 ±25 2.0 3.0 65 25 to 300 3.0K // 1.5 L-1 10M15D 8 3 ±7.5 70 ±17.5 90 ±25 2.0 4.0 90 25 to 300 3.0K // 1.5 L-2 10M15E 10 3 ±7.5 75 ±15 90 ±20 2.0 4.5 90 20 to 300 3.0K // 1.5 L-3 10M30A 2 3 ±15 15 ±50 - - 0.5 1.5 30 +300 to +1000 40 -300 to -1000 5.0K // 0 HC49T 10M30B 4 3 ±15 30 ±40 - - 1.0 2.5 30 40 to 300 5.5K // -1.0 Zc: 0.5 pF HC49Tx2 (a pair) 10M30C 6 3 ±15 60 ±45 - - 2.0 3.0 60 45 to 300 5.5K // -1.0 L-1 10M30D 8 3 ±15 60 ±30 80 ±40 2.0 3.5 90 50 to 300 5.5K // -1.0 L-2 If SMD bent lead package required please add “MJ” at the end of the part number. For example: 10M07AU1-MJ Zc: Coupling capacitance including stray capacitances HC-49/T U1SM UM-5 MERCURY UM-1 (4 poles) 49TMJ Page 2 of 6 U5SM Date: Dec. 1, 2001 Rev. 0 Monolithic Crystal Filters MERCURY Since 1973 21.4 MHz MCF 21.4 MHz Family Channel Spacing (kHz) 12.5 20 25 50 Operating Temperature Range: -10 to +70°C Pass Band Stop Band Insertion Guaranteed Terminating Width Ripple No. of Width (max.) Loss Attenuation Impedance Package (min.) Poles ohms// pF dB KHz dB kHz dB kHz dB max dB max dB (fo ±kHz) Model 21M07AU1 2 3 ±3.75 20 ±18 - - 0.5 1.5 21M07BU1 4 3 ±3.75 40 ±40 - - 1.0 2.0 21M07AU5 2 3 ±3.75 20 ±18 - - 0.5 1.5 21M07BU5 4 3 ±3.75 40 ±40 - - 1.0 2.0 21M07C 21M07D 21M07E 3 ±3.75 3 ±3.75 3 ±3.75 45 ±8.75 65 ±12.5 65 ±9 90 ±12.5 75 ±8.75 90 ±10.5 2.0 2.0 2.0 3.0 4.0 4.5 21M12AU1 2 3 ±6 20 ±25 - - 0.5 1.5 21M12BU1 4 3 ±6 40 ±20 - - 1.0 2.0 21M12AU5 2 3 ±6 20 ±25 - - 0.5 1.5 21M12BU5 4 3 ±6 40 ±20 - - 1.0 2.0 21M12C 21M12D 3 ±6 3 ±6 45 ±14 65 ±14 65 ±20 90 ±20 2.0 2.0 3.0 4.0 21M15AU1 2 3 ±7.5 18 ±25 - - 0.5 1.5 21M15BU1 4 3 ±7.5 40 ±25 - - 1.0 2.0 21M15AU5 2 3 ±7.5 18 ±25 - - 0.5 1.5 21M15BU5 4 3 ±7.5 40 ±25 - - 1.0 2.0 21M15C 21M15D 21M15E 3 ±7.5 3 ±7.5 3 ±7.5 45 ±17.5 65 ±25 65 ±17.5 90 ±25 75 ±17.5 90 ±20 2.0 2.0 2.0 2.5 3.0 4.0 21M30AU1 2 3 ±15 15 ±45 - - 0.5 1.5 21M30BU1 4 3 ±15 40 ±50 - - 1.0 2.0 21M30AU5 2 3 ±15 15 ±45 - - 0.5 1.5 21M30BU5 4 3 ±15 40 ±50 - - 1.0 2.0 21M30C 21M30D 3 ±15 3 ±15 45 ±35 70 ±35 65 ±50 90 ±50 2.0 2.0 2.5 3.5 6 8 10 6 8 6 8 10 6 8 35 +350 to +1000 50 -200 to -1000 65 +350 to +1000 80 -200 to -1000 35 +350 to +1000 50 -200 to -1000 65 +350 to +1000 80 -200 to -1000 65 +12.5 to +300 90 +12.5 to +300 90 +12.5 to +300 35 +350 to +1000 50 -200 to -1000 65 +350 to +1000 80 -200 to -1000 35 +350 to +1000 50 -200 to -1000 65 +350 to +1000 80 -200 to -1000 65 +20 to +300 90 +20 to +300 35 +350 ~ +1000 50 -200 ~ -1000 65 +350 to +1000 80 -200 to -1000 35 +350 ~ +1000 50 -200 ~ -1000 65 +350 to +1000 80 -200 to -1000 65 +25 to +300 90 +25 to +300 90 +18 to +300 35 +300 to +1000 45 -300 to -1000 65 +350 to +1000 80 -250 to -1000 35 +300 to +1000 45 -300 to -1000 65 +350 to +1000 80 -250 to -1000 65 +50 to +300 90 +50 to +1000 850 // 6 UM-1 850 // 5 Zc: 16 pF UM-1 x2 (a pair) 850 // 6 UM-5 850 // 5 Zc: 16 pF 850 // 5 850 // 5 850 // 5 UM-5 x2 (a pair) S-1 S-1 S-2 1.2K // 3.0 UM-1 1.2K // 2.5 Zc: 10.5 pF UM-1 (a pair) 1.2K // 3.0 UM-5 1.2K // 2.5 Zc: 10.5 pF 1.2K // 2.5 1.2K // 2.5 UM-5 (a pair) S-1 S-1 1.5K // 2.5 UM-1 1.5K // 2.0 Zc: 8 pF UM-1 (a pair) 1.5K // 2.5 UM-5 1.5K // 2.0 Zc: 8 pF 1.5K // 2.0 1.5K // 2.0 1.5K // 2.0 UM-5 (a pair) S-1 S-1 S-2 1.5K // 1.0 UM-1 2.0K // 0.5 Zc: 3 pF UM-1 (a pair) 1.5K // 1.0 UM-5 2.0K // 0.5 Zc: 3 pF 2.2K // 0.5 2.2K // 0.5 UM-5 (a pair) S-1 S-1 If SMD bent lead package required please add “MJ” at the end of the part number. For example: 21M07AU1-MJ Zc: Coupling capacitance including stray capacitances MERCURY Page 3 of 6 Date: Dec. 1, 2001 Rev. 0 Monolithic Crystal Filters MCF 45 MHz Fundamental mode Family Channel Spacing Model KHz 45M7.5AU1 12.5 Pass Band No. of Width (min) Poles dB kHz 2 3 ±3.75 Stop Band Width (max.) dB kHz 10 ±12.5 Operating Temperature Range: -10 to +70°C Insertion Guaranteed Ripple Loss Attenuation dB max dB max dB (fo ±kHz) 1.0 2.0 65 -910 4 3 ±3.75 30 ±12.5 1.0 4.0 90 45M15AU1 2 3 ±7.5 15 ±25 1.0 2.0 35 65 45M15BU1 4 3 ±7.5 30 ±25 1.0 3.0 90 45M30AU1 2 3 ±15 15 ±60 1.5 2.5 35 65 45M30BU1 4 3 ±15 30 ±50 1.0 3.0 80 45M7.5AU5 2 3 ±3.75 10 ±12.5 1.0 2.0 65 -910 45M7.5BU5 4 3 ±3.75 30 ±12.5 1.0 4.0 90 ±900 ~ ±1000 45M15AU5 2 3 ±7.5 15 ±25 1.0 2.0 35 65 45M15BU5 4 3 ±7.5 30 ±25 1.0 3.0 90 ±900 ~ ± 1000 45M30AU5 2 3 ±15 15 ±60 1.5 2.5 45M30BU5 4 3 ±15 30 ±50 1.0 3.0 50 25 50 Terminating Impedance (ohms // pF) 200 // 4 350 // 6.5 ±900 ~ ±1000 Zc: 18 pF +900 ~ +1000 650 // 3.0 -900 ~ -1000 650 // 3.0 ±900 ~ ± 1000 Zc: 9 pF +900 ~ +1000 1200 // 0 -900 ~ -1000 1200 // 0.7 ±900 ~ ±1000 Zc: 3.5 pF 45M7.5BU1 25 12.5 MERCURY Since 1973 45.0 MHz 900 ~ +1000 -900 ~ -1000 Package UM-1 UM-1x2 (a pair) UM-1 UM-1x2 (a pair) UM-1 UM-1x2 (a pair) 200 // 4 350 // 6.5 Zc: 18 pF UM-5 650 // 3.0 UM-5 650 // 3.0 Zc: 9 pF UM-5x2 (a pair) 35 +900 ~ +1000 1200 // 0 65 -900 ~ -1000 1200 // 0.7 80 ±900 ~ ±1000 Zc: 3.5 pF UM-5x2 (a pair) UM-5 UM-5x2 (a pair) If SMD bent lead package required please add “MJ” at the end of the part number. For example: 45M7.5AU1-MJ MCF 45 MHz 3rd Overtone Mode Family Channel Spacing Model kHz 12.5 25 12.5 25 Operating Temperature Range: -10 to +70°C No. Pass Band Stop Band Insertion Guaranteed Terminating Ripple Package of Width (min) Width (max) Loss Attenuation Impedance Poles dB kHz dB kHz dB max dB max dB (fo ± kHz) (ohms // pF) T45M7.5AU1 2 3 ±3.75 10 ±12.5 1.0 2.0 35 ±910 T45M7.5BU1 4 3 ±3.75 30 ±12.5 1.0 4.0 75 ±910 T45M15AU1 2 3 ±7.5 15 ±25 1.0 2.0 35 ±910 T45M15BU1 4 3 ±7.5 30 ±25 1.0 4.0 75 ±910 T45M7.5AU5 2 3 ±3.75 10 ±12.5 1.0 2.0 35 ±910 T45M7.5BU5 4 3 ±3.75 30 ±12.5 1.0 4.0 75 ±910 T45M15AU5 2 3 ±7.5 15 ±25 1.0 2.0 35 ±910 T45M15BU5 4 3 ±7.5 30 ±25 1.0 4.0 75 ±910 2000 // -0.4 3000 // -0.3 Zc: 0 pF 4000 // -0.7 4000 // -0.8 Zc: -1.0 pF UM-1 UM-1x2 (a pair) UM-1 UM-1x2 (a pair) 2000 // -0.4 3000 // -0.3 Zc: 0 pF 4000 // -0.7 4000 // -0.8 Zc: -1.0 pF UM-5 UM-5x2 (a pair) UM-5 UM-5x2 (a pair) If SMD bent lead package required please add “MJ” at the end of the part number. For example: T45M7.5AU1-MJ Zc: Coupling capacitance including stray capacitances MERCURY Page 4 of 6 Date: Dec. 1, 2001 Rev. 0 MERCURY Since 1973 Monolithic Crystal Filters PACKAGE DIMENSIONS (mm) HC-49/T 4 pole MCF (paired packages) UM-1, UM-5 L-3 UM-1: H=8.0 UM-5: H=6.0 S-1, S-2, L-1, L-2 and L-3 S-1 S-2 L-1 L-2 L-3 Pin #1: output Pin #3: ground MERCURY L W H P K 11.0 13.4 15.0 18.5 23.0 8.5 8.5 12.0 12.0 12.0 11.5 11.5 15.0 15.0 15.0 7.4 9.8 9.0 13.4 17.8 2.0 2.0 2.5 2.5 2.5 Pin #2: ground Pin #4: input Page 5 of 6 Date: Dec. 1, 2001 Rev. 0 φ D 0.3 0.3 0.43 0.43 0.43 MERCURY Since 1973 Monolithic Crystal Filters “F” package 6x35x12 “Q” package 5x7x13 Operating Temperature Range: -30 to +80°C Package Dimensions and Suggested Pad Layout: Q F Q F 2.54 [0.100] 5.0±0.2 1 In/out 2 4.6 [0.181] 4.4 [0.173] Pad 3 and 6: MCF in/out Pad 1,2,4,5: Metal lid for grounding 4.4 [0.173] Page 6 of 6 6.0 [0.236] Date: Dec. 1, 2001 Rev. 0 1.0 [0.040] 2.0 [0.078] 1.3 [0.051] max 1.4 [0.055] 2.2 [0.087] 2.4 [0.094] 1.3 [0.051] 1.9 [0.073] 1.4 [0.055] 3 In/out 6 4 1 2 In/out 1.2 [0.047] max [0.197±0.008] 0.9 [0.035] 2.4 [0.094] 3.5±0.2 [0.137±0.008] 3 5 7.0±0.2 6 5 4 1.2 [0.047] [0.275±0.008] In/out 1.4 [0.055] 6.0±0.2 [0.236±0.008] MERCURY F Package: "Q" 0.8 [0.031] Pad 1,2,4,5: Metal lid for grounding 1.5K // 2.5 1.5K // 2.5 1.5K // 6.0 550 // 3.0 1.2K // 1.5 350 // 6.0 550 // 5.0 560 // 6.0 1.2K // 1.8 950 // -1.6 Unit mm [inches] Package: "F" Pad 1 and 3: MCF In /out dB max 2.0 1.5 2.0 2.5 2.0 2.0 2.0 2.0 2.0 2.2 Package 1.2 [0.047] 128.55 dB max 1.0 0.5 1.0 0.5 1.0 1.0 1.0 1.0 1.0 1.2 Terminating Impedance (ohm // pF) 2.6 [0.102] 45 Insertion Loss 4.0 [0.157] 21.7 21MF15 21MQ15 217MQ7 45MF15 45MF30 45MQ7 45MQ12 45MQ15 45MQ30 128MF32 Ripple 0.7 [0.029] 21.4 Model 25.4 [0.100] Nominal Frequency (MHz) No. of Guaranteed Pass Band Stop Band poles Attenuatio Width Width n dB kHz dB kHz dB kHz 3 ±7.5 18 ±25 2 70 -910 3 ±7.5 18 ±25 2 70 -910 3 ±3.5 16 ±125 2 70 -910 3 ±7.5 14 ±25 2 70 -910 3 ±15 15 ±50 2 70 -910 3 ±3.75 20 ±25 2 70 -910 3 ±6.0 15 ±25 2 70 -910 3 ±7.5 15 ±25 2 70 -910 3 ±15 15 ±60 2 70 -910 3 ±16.1 20 ±57.6 3 73 -900