RPD-65 series

RPD-65
65W Dual Output Switching Power Supply
series
■ Features :
Universal AC input/Full range
12V or 24V high peak output current capability
Optional L-Bracket and cover (RPD-65x-C, x=C,D)
Low leakage current<1mA
Protections: Short circuit / Overload / Over voltage
60W free air convection, 77.1W with 18CFM forced air
100% full load burn-in test
Fixed switching frequency at 65KHz
2 years warranty
..
SPECIFICATION
MODEL
RPD-65C
CH1
CH2
CH1
CH2
DC VOLTAGE
12V
5V
24V
5V
RATED CURRENT
4.5A
1.2A
2.25A
1.2A
CURRENT RANGE
0 ~ 5.8A
0 ~ 1.5A
0 ~ 2.9A
0 ~ 1.5A
Rated load
3.75A
Rated load
PEAK LOAD
OUTPUT
RPD-65D
OUTPUT NUMBER
Note.4 7.5A
RATED POWER
60W
OUTPUT POWER (max.)
Rated output power for convection; 77.1W with 18CFM min. forced air
60W
RIPPLE & NOISE (max.) Note.2 120mVp-p
50mVp-p
150mVp-p
50mVp-p
±5.0%
VOLTAGE ADJ. RANGE
CH1:11.4 ~ 12.8V
VOLTAGE TOLERANCE Note.3 ±2.0%
INPUT
±5.0%
CH1:22.8 ~ 26.4V
±2.0%
LINE REGULATION
±1.0%
±1.0%
±1.0%
±1.0%
LOAD REGULATION
±2.0%
±5.0%
±2.0%
±5.0%
SETUP, RISE TIME
800ms, 20ms at full load
HOLD UP TIME (Typ.)
20ms at full load
VOLTAGE RANGE
90 ~ 264VAC
FREQUENCY RANGE
47 ~ 440Hz
EFFICIENCY (Typ.)
79%
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
1.5A/115VAC
LEAKAGE CURRENT
OVERLOAD
PROTECTION
OVER VOLTAGE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
SAFETY & WITHSTAND VOLTAGE
EMC
(Note 5)
127 ~370VDC
81%
0.9A/230VAC
COLD START 25A/115VAC
<1mA
50A/230VAC
90 ~ 125W output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed.
CH1:27.6 ~ 32.4V
CH1:13.8 ~ 16.2V
Protection type : Hiccup mode, recovers automatically after fault condition is removed.
-20 ~ +60℃ (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-40 ~ +85℃, 10 ~ 95% RH
±0.04%/℃ (0 ~ 50℃) on CH1 output
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL60950-1, TUV EN60950-1 approved
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A
MTBF
OTHERS
NOTE
288.1K hrs min. MIL-HDBK-217F (25℃)
PCB:127*76*29mm (L*W*H) ; with optional CASE:130*85*37mm (L*W*H)
PCB:0.24Kg; 63pcs/16Kg/1.35CUFT ; with optional CASE:0.47Kg;32pcs/16Kg/0.64CUFT
PACKING
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
DIMENSION
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. 10% duty cycle maximum within every second. Average output power should not exceed the rated power, output voltage above 90% DC voltage.
5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
File Name:RPD-65-SPEC 2015-07-17
RPD-65
65W Dual Output Switching Power Supply
Mechanical Specification
Case No. 946A
series
Unit:mm
Optional cover:
No. 946A-T
127
115.8
5.6
5.6
M2
M1
64.8
6
5
4
3
2
1
FS1
1
2
3
SVR1
18CFM min.
(60W convection, 77W with FAN)
7.1
3.8
2-M
FAM
3
11 5
29mm(max)
85
6-M
3L
4-M
.8
3L
=4
8.2
78
41
13
0
62
68
26
17
AC Input Connector (CN1) : Molex 5273-03 or equivalent
Pin No.
1
2
3
Assignment
AC/L
No Pin
AC/N
Mating Housing
Terminal
Molex 5195
or equivalent
Molex 5194
or equivalent
=4
37
15cm
4 -ψ
18
CN1
3 max.
76
CN2
.7
.6
Optional L-Bracket:
No. 946A-D
DC Output Connector (CN2) : Molex 5273-06 or equivalent
Pin No.
1,2
3,4
5
6
Assignment
V1
GND
V2
NC
Mating Housing
Terminal
Molex 5195
or equivalent
Molex 5194
or equivalent
: Grounding Required
1.M1 is safety ground. For better EMC performance,
Please secure an electrical connection between
M1,M2 and chassis grounding.
Block Diagram
fosc : 65KHz
I/P
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCHING
RECTIFIERS
&
FILTER
+V1
RECTIFIERS
&
FILTER
FG
O.L.P.
PWM
CONTROL
+V2
COM
DETECTION
CIRCUIT
O.V.P.
File Name:RPD-65-SPEC 2015-07-17
RPD-65
65W Dual Output Switching Power Supply
Derating Curve
Output Derating VS Input Voltage
100
100
PCB only
90
For PCB with
L-Bracket+cover option
80
70
LOAD(%)
LOAD (%)
For both PCB only and with
L-Bracket+cover option
80
60
40
20
-20
series
-10
0
10
20
30
40
AMBIENT TEMPERATURE (℃)
50
60 (HORIZONTAL)
60
50
40
90
100
110
135
155
230 264
INPUT VOLTAGE (V) 60Hz
File Name:RPD-65-SPEC 2015-07-17