MOSPEC KBU804 SINGLE-PHASE BRIDGE RECTIFIER FEATURES ＊Low cost ＊High forward surge current capability ＊Ideal for printed circuit board ＊High temperature soldering guaranteed: 260oc/10 second,0.375”(9.5mm)lead length at 5 lbs. (2.3kg) tension. MECHANICAL DATA ＊Case: Transfer molded plastic ＊Epoxy: UL94V-O rate flame retardant ＊Terminals：Lead Solderable Per MIL-STD-202 method 208 ＊Polarity：Polarity symbols marked on case ＊Mounting :Thru hole for #6 screw, 5 in,-lbs.Torqute Max. ＊Weight： 0.27 ounce, 7.59 gram MAXIMUM RATINGS AND ELECTRICAL CHARATERISTICS * Rating at 25℃ ambient temperature unless otherwise specified * Single phase,half wave. 60Hz, resistive or inductive load. * For capacitive load derate current bh 20 % Characteristic Symbol KBU804 Unit VRRM VRWM VDC 400 V VR(RMS) 280 V Average Rectifier Forward Current @ TA=100℃ (Note 3) @ TA=50℃ IO(AV) 8.0 6.0 A Non-Repetitive Peak Surge Current 8.3 ms Single half sine-wave superimposed on rated load ( JEDEC Method) IFSM 300 A Forward Voltage (per element) ( IF =8.0 Amp) VFM 1.0 V Peak Reverse Current ( Rated DC Voltage, TC = 25℃) ( Rated DC Voltage, TC = 125℃) IR 10 1.0 uA mA Rating for Fusing( t<8.3 ms) I2t 373 A2s Typical Junction Capacitance per element (Note1) CJ 200 pF Rθ jA 5.0 k/W TJ , Tstg -65 to +150 ℃ Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Typical Thermal Resistance (note 2) Operating and Storage Temperature Range Note: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0V D.C. 2. Unit mounted on 3.0”×3.0”×0.11” thick (7.5×7.5×0.3 cm ) Al. plate. 3. Unit mounted in free air, no heatsink, P.C.B. at 375”(9.5mm) lead length with. 5”×5”(12×12 mm) copper pads.. KBU804 FIG-2 TYPICAL FORWARD CHARACTERISITICS NSTANTANEOUS FORWARD CURRENT (Amp.) 60 Hz Resistive or Inducttive Load Heat Sink Mounting 3.0”×3.0”×0.11” (7.5×7.5×0.3 cm AL Plate TC Case temperature Ambient TA Temperature P.C.B Mounting 0.47”×0.47” (12×12 mm) Copper Pads 0.375”(9.5mm) Lead Length O TJ=25 C Pulse Width=300us 1% Duty Cycle FORWARD VOLTAGE (Volts) FIG-3 PEAK FORWARD SURGE CURRENT FIG-4 TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE (PF) CASE TEMPERATURE (℃) O TJ=25 C Single Half Sine Wave (JEDEC Method) O TJ=25 C f=1MHz NUMBER OF CYCLES AT 60 Hz REVERSE VOLTAGE (Volts) FIG-5 TYPICAL REVERSE CHARACTERISTICS IR, INSTANTANEOUS REVERSE CURRENT (uA) IIFSM, PEAK FWD SURGE CURRENT (A) AVERAGE FORWARD RECTIFIED CURRENT (Amp.) FIG-1 FORWARD CURRENT DERATING CURVE O TJ=125 C O TJ=25 C PERCENT OF RATED REVERSE VOLTAGE (﹪)