Tippette Full Sized Rocker Switches The Tippette Series is a traditionally styled rocker switch, available in sealed or unsealed versions. These switches are appropriate for use in general purpose applications which may or may not require a modicum of environmental protection. The Tippette Series is available in both illuminated and non-illuminated versions and features a wide variety of circuits, actuator styles and bracket options. This versatile offering includes international agency certifications and ratings to 26 amps for select circuits. Carling Technologies, Inc. 60 Johnson Avenue • Plainville, CT 06062-1177 Phone: (860) 793-9281 • Fax: (860) 793-9231 Email: [email protected] • www.carlingtech.com 2 | Tippette Switches (TIG,TIH,TII & LTIL,LTIG) - General Specifications Electrical Physical Contact Rating 15 amps, 125 VAC 10 amps, 250 VAC 3/4 HP 125-250 VAC 15 amps, 12-30 VDC Life 25,000 cycles circuit dependent 50,000 cycles circuit dependent consult factory for applicable circuits. Contacts Fine silver, silver cad-oxide Terminals Brass or copper/silver plate 1/4” (6.3mm) Quick Connect terminations standard. Solder lug - Brass Tin Plated Wire Lead 16 gauge standard 105°C 600VAC Screw Terminals - Brass Lighted Seals Base Rocker/Bracket Mechanical Endurance Incandescent - rated 10,000 hours Neon - rated 25,000 hours Bracket - Actuator WBL/MBL optional external gasket panel seal Phenolic (150°C) Nylon 66 (105°C) Agency Certifications Select circuits and constructions with IEC approvals are available. Consult factory Mounting 1.190[30.22] 100,000 cycles minimum MOUNTING HOLE (Nylon Snap-in Brackets) Panel Thickness: .040 min. - .250 max. .680[17.27] .830[21.08] 1.450[36.83] 55 4 plcs * *Angled corners are suggested for optimum fit. Standard rectangular cutout is acceptable. *Manufacturer reserves the right to change product specification without prior notice. 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com TIG/TIH/TII & LTIL/LTIG-Series Rocker & Paddle Switches | 3 TIGA51 6M 2 Actuator Style 1 Base Part Number BL 3 Actuator Color 1 BASE PART NUMBER: SERIES/POLES/CIRCUITRY8,11,13/RATING7/TERMINATION10 10A 250VAC, 15A 125VAC, 3/4 HP 125-250VAC, 15A 6-28VDC7 Single Pole in Double Pole base2 Double Pole solder .250 screw wire solder .250 screw wire lug tab term. leads lug tab term. leads TIGA50 TIGA51 TIGA54 TIGA55 On-None-Off TIGK50 TIGK51 TIGK54 TIGK55 TIGA5A TIGA5BTIGA5E TIGA5F (On)-None-Off TIGK5A TIGK5BTIGK5ETIGK5F TIGA5L TIGA5MTIGA5S TIGA5T On-None-(Off) TIGK5L TIGK5MTIGK5STIGK5T TIGB50 TIGB51TIGB54 TIGB55 On-None-On TIGL50 TIGL51 TIGL54TIGL55 TIGB5A TIGB5BTIGB5E TIGB5F On-None-(On) TIGL5A TIGL5BTIGL5ETIGL5F TIGC50 TIGC51TIGC54 TIGC54 On-Off-On TIGM50 TIGM51 TIGM54TIGM55 TIGC5A TIGC5BTIGC5E TIGC5F On-Off-(On) TIGM5A TIGM5BTIGM5ETIGM5F TIGC5L TIGC5MTIGC5S TIGC5T (On)-Off-(On) TIGM5L TIGM5MTIGM5STIGM5T Three Pole Four Pole solder .250 screw wire solder .250 screwwire lug tab term. leads lug tab term.leads TIHK50 TIHK51TIHK54 TIHK55On-None-Off TIIK50 TIIK51 TIIK54TIIK55 TIHK5A TIHK5BTIHK5E TIHK5F(On)-None-Off TIIK5A TIIK5BTIIK5ETIIK5F TIHK5L TIHK5MTIHK5S TIHK5TOn-None-(Off) TIIK5L TIIK5MTIIK5STIIK5T TIHL50 TIHL51TIHL54 TIHL55On-None-On TIIL50 TIIL51 TIIL54TIIL55 TIHL5A TIHL5BTIHL5E TIHL5FOn-None-(On) TIIL5A TIIL5BTIIL5ETIIL5F TIHM50 TIHM51TIHM54 TIHM54On-Off-On TIIM50 TIIM51 TIIM54TIIM55 TIHM5A TIHM5BTIHM5E TIHM5FOn-Off-(On) TIIM5A TIIM5BTIIM5ETIIM5F TIHM5L TIHM5MTIHM5S TIHM5T (On)-Off-(On) TIIM5L TIIM5MTIIM5STIIM5T VDE APPROVED 10A 250VAC, 15A 125VAC, 12(6)A 250VAC T85 Single Pole in Double Pole base2 Double Pole solder.250 wire solder .250 wire lug tablead lug tab lead TIGA90 TIGA91TIGA95 On-None-Off TIGK90 TIGK91TIGK95 TIGB90 TIGB91TIGB95 On-None-On TIGL90 TIGL91TIGL95 TIGC90 TIGC91TIGC95 On-Off-On TIGM90 TIGM91TIGM95 Additional ratings up to 20A 125-277VAC, 1 1/2HP 125 VAC, 2HP 250VAC are available. Consult factory for specifics. 2 ACTUATOR STYLE 1S Angular/Smooth Face Gloss12 1C Angular/Cross Serations Gloss12 1F Flatted/Smooth Face Gloss12 1L Angular/Longline Serrations Gloss1,12 2L Long Smooth/Narrow15 LTILA51 1 Base Part Number 6M 6S 7S 7N 7P 6M 2 Actuator Style Curved/Smooth Face Matte3 Curved/Smooth Face Gloss3 Rounded Paddle/Smooth Face Gloss1 Witch’s Hat/Narrow15 Witch’s Hat/Wide15 BL 3 Actuator Color RC 4 Lens Color MBL 4 Bracket 3 ACTUATOR COLOR9 BL black WH white RD red 4 BRACKET STYLE9 A Screw Mount5 B Screw Mount5,12 C Screw Mount5 H Screw Mount5 NBL Nylon Black WBL Watershedding Black4 MBL Marine Style Black4,6 FN Metal Snap-In5 FN BLK Black Metal Snap-In5 FN SS Stainless Steel Snap-In5 FW Wide Stainless Steel Snap-In5 Notes: 1 NBL, FN, & FW brackets only. 2 For single pole switch in a single pole base, specify TIL with single pole circuitry/rating/termination. 3 NBL, WBL, & MBL brackets only. With 6M actuator, brackets also will be matte finish. 4 6M & 6S actuators only 5 Not available with 6M & 6S actuators. 6 Consists of WBL bracket, neoprene seal, and dummy rivets at open holes. Consult factory for agency approval status. 7 All ratings are appropriate for usage in low voltage applications. 8 For additional special circuits, see page 21......?!?!?! 9 Custom colors are available, consult factory. 10 .187 tab and PC terminations are also available. Consult factory for catalog number callout. 11 ( ) momentary 12 Not available with WBL or MBL style brackets. 13 Additional circuits available. See page 21. 14 Available with bracket A, C or H only. 15 Not available with MBL, WBL or H brackets. Can be supplied as a double rocker to control separate poles of a TIG,TIH or TII switch. Consult factory for details. MBL 12V 5 Bracket 6 Lamp Voltage 1 BASE PART NUMBER: SERIES/POLES/ILLUMINATION/CIRCUITRY12/RATING10/TERMINATION14 10A 250VAC, 15A 125VAC, 3/4 HP 125-250VAC, 15A 15-28VDC illuminated Single Pole in Double Pole base illuminated Double Pole solder.250 screw wire solder .250 screw wire lug tab term. leads lug tab term leads LTILA50 LTILA51LTILA54 LTILA55 On-None-Off LTIGK50LTIGK51LTIGK54LTIGK55 LTILA5A LTILA5BLTILA5E LTILA5F (On)-None-Off LTIGK5A LTIGK5BLTIGK5E LTIGK5F LTILA5L LTILA5MLTILA5S LTILA5T On-None-(Off) LTIGK5L LTIGK5MLTIGK5S LTIGK5T LTILB50 LTILB51LTILB54 LTILB55 On-None-On LTIGL50LTIGL51LTIGL54LTIGL55 LTILB5A LTILB5BLTILB5E LTILB5F On-None-(On) LTIGL5A LTIGL5BLTIGL5E LTIGL5F LTILC50 LTILC51LTILC54 LTILC55 On-Off-On LTIGM50LTIGM51LTIGM54LTIGM55 LTILC5A LTILC5BLTILC5E LTILC5F On-Off-(On) LTIGM5A LTIGM5BLTIGM5E TIGM5F LTILC5L LTILC5MLTILC5S LTILC5T (On)-Off-(On) LTIGM5L LTIGM5MLTIGM5S LTIGM5T 2 ACTUATOR STYLE4 Additional ratings up to 12A 250VAC, 17A 125 VAC, 3/4 HP 125 VAC, 1HP 250VAC are available. Consult factory for specifics. Three pole switch is also available: Substitute H for fourth digit of part number. ex. LTIHK51 AMamber RCred GNgreen7 LUblue7 CLclear WHwhite Notes: 1 NBL, FN, & FW brackets only. Double pole circuits provided with 3 pole base. 2 LTIL-Series with NBL, FN, & FW brackets only. 3 NBL, WBL, & MBL brackets only. With 6M actuator, bracket will also be matte finish. 4 1S, 1C, 1L & 7S with NBL bracket only available with LTIL-Series. 5 6M, 6S actuators only. 6 Not available with 6M and 6S actuators. 7 Not recommended with neon lamps. 8 Consists of WBL bracket, neoprene seal, dummy rivets at open holes. Consult factory for agency approval status. 9 Not recommended with blue or green lenses. 10 All ratings are appropriate for usage in low voltage applications. 11 Custom colors and additional bracket styles are available, consult factory. 12 ( ) - momentary 13 All double throw circuits supplied with two lenses. To specify two different lens colors, specify second color, after first color. (ex. LTIGM51-6S-BL-RC/GN-WBL-12V) 14 .187 tab and PC terminations are also available. Consult factory for catalog number callout. 1S 1C 1L 6M 6S 7S Angular/Smooth Face Gloss1 Angular/Cross Serations Gloss1 Angular/Longline Serrations Gloss1 Curved/Smooth Face Matte3 Curved/Smooth Face Gloss3 Rounded Paddle/Smooth Face Gloss2 3 ACTUATOR COLOR11 BL black WH white RD red 4 LENS COLOR13 5 BRACKET STYLE11 NBL WBL MBL FN FN BLK FN SS Nylon Black Watershedding Black5 Marine Style Black5,8 Metal Snap-In4,6 Black Metal Snap-In4,6 Stainless Steel Snap-In4,6 6 LAMP VOLTAGE neon9 125N 125 volt incandescent 6V 6 volt 24V 24 volt 250N 250 volt 12V 28V 12 volt 28 volt 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com 18V 18 volt 4 | Tippette Rocker & Bracket Styles 1C 1L 1S CROSS-LINE W/ONE LENS LONG-LINE W/ONE LENS SMOOTH W/ONE LENS 1.700[43.18] 1.700[43.18] 1.700[43.18] .960[24.38] .650[16.51] .960[24.38] .418[10.62] 1.069[27.15] ± .020 .422[10.72] 1.440[36.58] 1.440[36.58] WITH.250 TAB TERMINALS AND NBL BRACKET 1.069[27.15] ±.020 .312[7.92] .422[10.72] WITH SOLDER LUG TERMINAL AND NBL BRACKET 1F WITH.250 TAB TERMINALS AND NBL BRACKET 7S 6M, 6S FLATTED STYLE NO LENS TOGGLE-STYLE W/ONE LENS CURVED W/ONE LENS 1.700[43.18] .900[22.86] .960[24.38] .650[16.51] .900[22.86] 1.570[39.88] .356[9.04] 1.570[39.88] .418[10.62] .060[1.52] 1.080[27.43] ± .020 .422[10.72] .828[21.03] .060[1.52] 1.080[27.43] 1.069[27.15] ±.020 1.440[36.58] .422[10.72] .312[7.92] WITH.250 TAB TERMINALS AND FN BRACKET WITH SOLDER LUG TERMINALS AND NBL BRACKET WITH.250 TAB TERMINALS AND FN BRACKET 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com Tippette Actuator Styles | 5 .650[16.51] .075[1.91] DIA .125[3.18] DIA .330[8.38] 1.069[27.15] .392[9.95] .372[9.45] .055[1.40] DIA .437[11.09] .394[10.00] .250[6.35] .187[4.74] .187[4.74] SOLDER LUG .250 TAB (Q.C.) TERMINAL TYPE .820[20.82] #6-32NC-2 THREAD .370[9.39] .075[1.905] IEC APPROVED CONSTRUCTION (TIG ONLY) 55˚ 4 plcs* .650[16.51] 1.224[31.08] .957[24.30] 1.224[31.08] 1L 1.224[31.08] .650[16.51] .957[24.30] 1.224[31.08] 1C TIL,TIG,TIH,TII .312[7.92] .300[7.62] .650[16.51] .957[24.30] 1.024[26.00] 2L TIG, TII 1.224[31.08] TIL,TIG,TIH,TII .250[6.35] 6S TIG .630[16.00] .430[10.90] .650[16.51] .957[24.30] 1S TIL,TIG,TIH,TII 1.224[31.08] 1F * Angled corners are suggested for optimum fit. Standard rectangular cutout is acceptable. .650[16.51] TIL,TIG,TIH,TII .957[24.30] WIRE LEAD MOUNTING HOLE (Nylon Snap-in Brackets) Panel Thickness: .030 min. - .250 max. Switch should be mounted at 90˚ for maximum water shedding (45˚ to 90˚ acceptable) .830[21.08] 1.450[36.83] .350[8.89] SCREW (ASSEMBLED) .680[17.27] .187[4.75] .500[12.70] .286[7.26] 1.190[30.22] .187[4.75] 6.000[152.40] .141[3.58] 1.069[27.15] .490[22.86] .187 TAB (Q.C.) 1.035[26.28] .996[25.30] 1.224[31.08] 7S TIG .880[22.40] Indicates momentary function. 7P TIG SPECIAL CIRCUITS FOR TIPPETTE ROCKER SWITCHES Circuit Position 1 Position 2 Progressive Two Circuit GG BOTH CIRCUITS ON ONE CIRCUIT ON GG BOTH CIRCUITS (ON) ONE CIRCUIT ON Single Pole Triple Throw GEON ON Two Circuit GH CIRCUIT 1 ON BOTH CIRCUITS ON GP CIRCUIT 2 ON CIRCUIT 1 ON Reversing Double Pole Double Throw GOON OFF GX ON NONE () .880[22.4] 7N TIG Position 3 OFF OFF ON CIRCUIT 2 ON OFF ON ON 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com PRINTED CIRCUIT 6 | Tippette Mounting Bracket Styles Dimensional Specifications: in. [mm] 1.190[30.22] # 6-32NC-2 TAP .680[17.27] .156[3.96] DIA .070[1.77] .830[21.08] .158[4.01] DIA TAPPED HOLE CLEARANCE HOLE TIG TIL 1.940[49.27] (Nylon Snap-in Brackets) Panel Thickness: .030 min. - .250 max. * Angled corners are suggested for optimum fit. Standard rectangular cutout is acceptable. TIH TII 1.940[49.27] .078[1.98] MOUNTING HOLE Standard with C Bracket Standard with A & B Brackets 1.892[48.06] .078[1.98] 1.960[49.78] .078[1.98] .078[1.98] 1.625[41.27] 1.625[41.27] 1.625[41.27] TIL TIG TII A 1.625[41.27] A A 2.093[53.16] A TIH 2.090[53.08] .156[3.96] .156[3.96] 1.625[41.27] 1.625[41.27] B B TIL TII, TIG 1.875[47.62] .437[11.09] 55˚ 4 plcs* 1.450[36.83] 1.940[49.27] 2.062[52.37] .426[10.82] .426[10.82] 1.625[41.27] CX 1.625[41.27] 1.625[41.27] TIG TIH, TII C TIL C 1.950[49.53] 1.700[43.18] 1.350[34.29] GCP GLOSS FINISH .960[24.38] 1.625[41.27] 1.570[39.88] H GMP MATTE FINISH HOLE PLUG FOR TIL, TIG, TIH & TII .430[10.92] TIG NARROW WIDE 1.750[44.45] 1.570[39.87] 1.126[28.60] .900[22.86] FN TIL, TIG, TIH, TII METAL, SNAP-IN MARINE / STD / WATERSHEDDING 1.700[43.18] .960[24.38] FW TIL, TIG, TIH, TII METAL, SNAP-IN MBL, NBL, WBL TIG BLACK NYLON, SNAP-IN REV_SW_Tippette_0712 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com