ALUMINUM ELECTROLYTIC CAPACITORS UN Chip Type, Bi-Polarized, Higher Capacitance Range series Chip Type ,higher capacitance in larger case sizes (φ12.5, φ16, φ18, φ20) Designed for surface mounting on high density PC board. Bi-polarized series for operations over wide temperature range of –55 to +105°C. Applicable to automatic mounting machine fed with carrier tape and tray. Compliant to the RoHS directive (2011/65/EU). UN Bi-polarized UJ Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 6.3 to 100V Rated Capacitance Range 22 to 3300µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.26 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.22 16 0.18 25 0.16 35 0.14 50 0.12 63 0.10 100 0.09 For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. Measurement frequency: 120Hz Rated voltage (V) Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z–25°C / Z+20°C Z–40°C / Z+20°C 6.3 5 10 10 4 8 16 3 6 25 2 4 35 2 3 50 2 3 63 2 3 100 2 3 Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C with the polarity inverted every 250 hours. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Marking Black print on the case top. Chip Type Plastic platform C ±0.2 Series A ±0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 UUN 1 H 3 3 1 M NQ 1 MS Package code A ±0.2 E B ±0.2 φD ±0.5 330 µF UN 50V H1015 nichicon BP Pressure relief vent 1 0.5 MAX. 0.3 MAX. Lot No. Capacitance Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 50V 330µF) Voltage Trade mark Capacitance change tan δ Leakage current L ±1.0 H Taping MS Tray ZD Size code Configuration Capacitance Tolerance(±20%) Rated capacitance(330μF) φD Code 12.5 to 18 NQ 20 RQ Rated voltage(50V) (mm) φD 12.5×13.5 12.5×16. 16×16.5. 16×21.5. 18×16.5. 18×21.5. 20×21.5. 4.8 4.8 5.4 5.4 6.4 6.4 6.2 A 13.6 13.6 17.1 17.1 19.1 19.1 21.1 B 13.6 13.6 17.1 17.1 19.1 19.1 21.1 C 4.0 4.0 6.3 6.3 6.3 6.3 8.8 E 13.5 16.0 16.5 21.5 16.5 21.5 21.5 L H 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.3 to 1.7 Series name Type The vibration structure-resistant product is also available upon request, please ask for details. Dimension table in next page. CAT.8100D ALUMINUM ELECTROLYTIC CAPACITORS UN series Dimensions V (µF) Cap. 6.3 10 16 25 35 50 63 0J 1A 1C 1E 1V 1H 1J Code 22 220 33 330 47 470 100 101 220 221 330 331 470 1000 2200 3300 471 102 222 332 12.5 × 13.5 12.5 × 13.5 310 16 × 16.5 270 370 12.5 × 13.5 270 12.5 × 13.5 340 16 × 16.5 420 16 × 16.5 490 12.5 × 16 500 16 × 16.5 600 18 × 16.5 670 18 × 21.5 780 16 × 21.5 670 18 × 16.5 740 18 × 21.5 830 16 × 21.5 740 18 × 21.5 920 In this case, 6 will be put at 12th digit of type numbering system, " " 12.5 × 13.5 180 16 × 16.5 330 18 × 16.5 450 16 × 21.5 450 18 × 21.5 590 100 2A 12.5 × 13.5 100 12.5 × 16 150 12.5 × 13.5 130 12.5 × 13.5 140 16 × 16.5 180 12.5 × 16 230 16 × 16.5 270 18 × 21.5 310 18 × 16.5 400 18 × 21.5 440 16 × 21.5 400 18 × 21.5 540 20 × 21.5 590 18 × 21.5 590 Case size φ D × L (mm) Rated ripple 20 × 21.5 640 18 × 21.5 640 Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency 50 Hz 0 22 to 470 0.75 100 to 470 0.80 1000 to 3300 0.85 Cap.(µF) 120 Hz 1.00 1.00 1.00 300 Hz 1.35 1.23 1.10 1 kHz 1.57 1.34 1.13 10 kHz or more 2.00 1.50 1.15 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D