Tantalum Surface Mount Capacitors One world. One KEMET.

Tantalum Surface Mount Capacitors
Standard Tantalum
tantalum standard
One world. One KEMET.
Electronic Components
Tantalum Surface Mount Capacitors
Standard Tantalum
Table of Contents Page
Why Choose KEMET......................................................................................................................................................... 3
T491 Series Industrial Grade MnO2 ................................................................................................................................. 5
T489 Series Low DC Leakage MnO2 .............................................................................................................................. 22
T490 Series Commercial Grade MnO2 .......................................................................................................................... 33
Packaging Information.................................................................................................................................................... 43
KEMET Corporation Sales Offices................................................................................................................................ 48
Disclaimer........................................................................................................................................................................ 49
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
2
One world. One source. One KEMET.
When you partner with KEMET, our entire global organization provides you with the
coordinated service you need. No bouncing from supplier to supplier. No endless phone
calls and web browsing. We’re your single, integrated source for electronic component
solutions worldwide.
Less hassles. More solutions.
Our commitment to product quality and on-time delivery has helped customers
succeed for over 90 years. There’s a reason KEMET components can be found in
defense and aerospace equipment. Our reputation is built on a history of consistency,
reliability and service.
The “Easy-to-Buy-From” company.
KEMET offers a level of responsiveness that far surpasses any other supplier. Our
passion for customer service is evident throughout our global sales organization, which
offers localized support bolstered by our worldwide logistics capabilities. Whether you
need rush samples, technical assistance, in-person consultation, accelerated custom
design, design collaboration or prototype services, we have a solution.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
One World. One KEMET
3
Made for you.
When you need custom products delivered on a tight schedule, you can trust KEMET.
Get direct design consultation from global experts, who help you get the job done on
time and within budget.
Working for a better world.
KEMET is dedicated to economically, environmentally and socially sustainable
development. We’ve adopted the Electronic Industry Code of Conduct (EICC) to
address all aspects of corporate responsibility. Our manufacturing facilities have won
numerous environmental excellence awards and recognitions, and our supply chain is
certified. We believe doing the right thing is in everyone’s interest.
About KEMET.
KEMET Corporation is a leading global supplier of electronic components. We offer
our customers the broadest selection of capacitor technologies in the industry across
multiple dielectrics, along with an expanding range of electromechanical devices, and
electromagnetic compatibility solutions. Our vision is to be the preferred supplier of
electronic component solutions for customers demanding the highest standards of
quality, delivery and service.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
One World. One KEMET
4
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Overview
The KEMET T491 Series, designed specifically for today’s highly
automated surface mount processes and equipment, is the
leading choice for surface mount designs. The T491 combines
KEMET’s proven solid tantalum technology, acclaimed and
respected throughout the world, with the latest in materials,
processes and automation, resulting in unsurpassed total
performance and value. This product meets or exceeds the
requirements of EIA standard 535BAAC. This series is classified
as MSL (Moisture Sensitivity Level) 1 under J STD 020: unlimited
floor life time at ≤30°C / 85% RH. The T491 standard terminations
are available in 100% matte tin and provide excellent wetting
characteristics and compatibility with today's surface mount solder
systems. Tin/lead (Sn/Pb) terminations are available upon request
for any part number. Gold-plated terminations are also available
for use with conductive epoxy attachment processes. Standard
packaging of these devices is tape and reel in accordance with
EIA 481. This system provides perfect compatibility with all tapefed placement units.
Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
Meets or exceeds EIA Standard 535BAAC
Taped and reeled per EIA 481
Symmetrical, compliant terminations
Optional gold-plated terminations
Laser-marked case
100% surge current test on C, D, E, U, V, X sizes
Halogen free epoxy
Capacitance 0.1 µF to 1,000 µF
Tolerance ±10%, ±20%
Voltage 2.5 – 50 VDC
Extended range values
Low profile case sizes
RoHS Compliant and lead-free terminations
(See www.kemet.com for transition information)
• Operating temperature: -55ºC to +125ºC
Applications
Typical applications include decoupling and filtering in industrial and automotive end applications such as DC/DC converters, portable
electronics, telecommunications, and control units.
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
15
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
SPICE
For a detailed analysis of specific part numbers, please visit www.kemet.com for a free download of KEMET's SPICE software.
The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over
frequency, temperature, ripple, and DC bias conditions.
Ordering Information
T
491
X
157
K
Capacitor
Class
Series
Case Size
Capacitance
Code (pF)
Capacitance
Tolerance
Rated Voltage Failure Rate/
(VDC)
Design
Industrial
A, B, C, D,
E, S, T, U,
V, W, X
K = ±10%
M = ±20%
2R5 = 2.5
003 = 3
004 = 4
006 = 6.3
010 = 10
016 = 16
020 = 20
025 = 25
035 = 35
050 = 50
T=
Tantalum
First two digits
represent
significant
figures. Third digit
specifies number
of zeros.
020
A
A = N/A
T
Termination Finish
Packaging (C-Spec)
T = 100% Matte Tin (Sn) Blank = 7" Reel
7280 = 13" Reel
plated
H = Standard solder
coated (SnPb 5% Pb
minimum)
G = Gold plated (A, B, C,
D, X only)
N = Non-magnetic 100%
Tin (Sn)
M = Non-magnetic (SnPb)
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
-55°C to 125°C
0.1 – 1,000 µF at 120 Hz/25°C
K Tolerance (10%), M Tolerance (20%)
2.5 – 50 V
DF (120 Hz)
Refer to Part Number Electrical Specification Table
ESR (100 kHz)
Refer to Part Number Electrical Specification Table
Leakage Current
≤ 0.01 CV (µA) at rated voltage after 5 minutes
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
62
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Qualification
Test
Condition
Characteristics
Δ C/C
Endurance
Storage Life
Thermal Shock
Temperature Stability
85°C at rated voltage, 2,000 hours
125°C at 2/3 rated voltage, 2,000 hours
125°C at 0 volts, 2,000 hours
MIL–STD–202, Method 107, Condition B, mounted, -55C° to
125° C, 1,000 cycles
Extreme temperature exposure at a
succession of continuous steps at +25ºC,
-55ºC, +25ºC, +85ºC, +125ºC, +25ºC.
DF
Within initial limits
DCL
Within 1.25 x initial limit
ESR
Within initial limits
Δ C/C
Within ±10% of initial value
DF
Within initial limits
DCL
Within 1.25 x initial limit
ESR
Within initial limits
Δ C/C
Within ±5% of initial value
DF
Within initial limits
DCL
Within 1.25 x initial limit
ESR
Within initial limits
+25°C
-55°C
+85°C
+125°C
Δ C/C
IL*
±10%
±10%
±20%
DF
IL
IL
1.5 x IL
1.5 x IL
DCL
IL
N/A
10 x IL
12 x IL
Δ C/C
Surge Voltage
Mechanical Shock/Vibration
Within ±10% of initial value
85°C, 1.32 x rated voltage 1,000 cycles
(125°C, 1.2 x rated voltage).
MIL–STD–202, Method 213, Condition I, 100 G peak
MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz,
20 G peak
Within ±5% of initial value
DF
Within initial limits
DCL
Within initial limits
ESR
Within initial limits
Δ C/C
Within ±10% of initial value
DF
Within initial limits
DCL
Within initial limits
*IL = Initial limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
73
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Electrical Characteristics
Capacitance vs. Frequency
ESR vs. Frequency
100
1,000
T491C336M025AT_IMP
T491C336M025AT
10
T491D476M025AT
T491X107M025AT_IMP
T491X107M025AT
T491C336M025AT_ESR
Capacitance (µF)
Impedance, ESR (Ohms)
T491D476M025AT_IMP
T491D476M025AT_ESR
T491X107M025AT_ESR
1
0.1
0.01
100
1,000
10,000
100,000
1,000,000
Frequency (Hz)
100
10
1
10,000,000
100
1,000
10,000
100,000
1,000,000
Frequency (Hz)
10,000,000
Dimensions – Millimeters (Inches)
Metric will govern
CATHODE (-) END VIEW
SIDE VIEW
ANODE (+) END VIEW
BOTTOM VIEW
A
B
W
B
H
X
T
S
G
Termination cutout
at KEMET's option,
either end
S
Case Size
KEMET
EIA
A
3216–18
B
3528–21
C
6032–28
D
7343–31
X
7343–43
E
7360-38
S
3216–12
T
3528–12
U
6032–15
V
7343-20
W
7343-15
F
E
P
R
L
Component
L*
W*
H*
3.2 ±0.2
1.6 ±0.2
1.6 ±0.2
(0.126 ±0.008) (0.063 ±0.008) (0.063 ±0.008)
3.5 ±0.2
2.8 ±0.2
1.9 ±0.2
(0.138 ±0.008) (0.110 ±0.008) (0.075 ±0.008)
6.0 ±0.3
3.2 ±0.3
2.5 ±0.3
(0.236 ±0.012) (0.126 ±0.012) (0.098 ±0.012)
7.3 ±0.3
4.3 ±0.3
2.8 ±0.3
(0.287 ±0.012) (0.169 ±0.012) (0.110 ±0.012)
7.3 ±0.3
4.3 ±0.3
4.0 ±0.3
(0.287 ±0.012) (0.169 ±0.012) (0.157 ±0.012)
7.3 ±0.3
6.0± 0.3
3.6 ± 0.2
(0.287 ±0.012) (0.236 ±0.012) (0.142 ±0.008)
3.2 ±0.2
1.6 ±0.2
1.2 (0.047)
(0.126 ±0.008) (0.063 ±0.008)
3.5 ±0.2
2.8 ±0.2
1.2 (0.047)
(0.138 ±0.008) (0.110 ±0.008)
6.0 ±0.3
3.2 ±0.2
1.5 (0.059)
(0.236 ±0.012) (0.110 ±0.008)
7.3 ±0.3
4.3 ±0.3
2.0 (0.079)
(0.287 ±0.012) (0.169 ±0.012)
7.3 ±0.3
4.3 ±0.3
1.5 (0.059)
(0.287 ±0.012) (0.169 ±0.012)
F* ±0.1
±(0.004)
1.2 (0.047)
2.2 (0.087)
2.2 (0.087)
2.4 (0.094)
2.4 (0.094)
4.1 (0.161)
1.2 (0.047)
2.2 (0.087)
2.2 (0.087)
2.4 (0.094)
2.4 (0.094)
S*
0.80 (0.032) + 0.2
(0.008) /-0.3(0.011)
0.80 (0.032) + 0.1
(0.004) /-0.3(0.011)
1.30 (0.051)
±0.3 (0.011)
1.30 (0.051)
±0.3 (0.011)
1.30 (0.051)
±0.3 (0.011)
1.30 (0.051)
±0.3 (0.011)
0.80 (0.032) + 0.2
(0.008) /-0.3(0.011)
0.80 (0.032) + 0.1
(0.004) /-0.3(0.011)
1.30 (0.051)
±0.3 (0.011)
1.30 (0.051)
±0.3 (0.011)
1.30 (0.051)
±0.3 (0.011)
B* ±0.15
(Ref) ±0.006
0.4 (0.016)
0.4 (0.016)
0.5 (0.020)
0.5 (0.020)
0.5 (0.020)
0.5 (0.020)
X (Ref)
P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref)
0.10 ±0.10
0.4 (0.016)
(0.004 ±0.004)
0.10 ±0.10
0.5 (0.020)
(0.004 ±0.004)
0.10 ±0.10
0.9 (0.035)
(0.004 ±0.004)
0.10 ±0.10
0.9 (0.035)
(0.004 ±0.004)
0.10 ±0.10
1.7 (0.067)
(0.004 ±0.004)
0.10 ± 0.10
N/A
(0.004 ±0.004)
0.4 (0.016)
1.0 (0.039)
1.0 (0.039)
1.0 (0.039)
1.0 (0.039)
N/A
N/A
0.05 (0.002)
N/A
N/A
N/A
0.05 (0.002)
N/A
N/A
N/A
0.05 (0.002)
N/A
N/A
N/A
0.05 (0.002)
N/A
N/A
N/A
0.05 (0.002)
N/A
N/A
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
0.13
(0.005)
1.2 (0.047) 1.1 (0.043) 1.3 (0.051)
1.9 (0.075) 1.8 (0.071) 2.2 (0.087)
2.9 (0.114) 2.8 (0.110) 2.4 (0.094)
3.6 (0.142) 3.5 (0.138) 3.5 (0.138)
3.6 (0.142) 3.5 (0.138) 3.5 (0.138)
1.2 (0.047) 3.5 (0.138) 3.5 (0.138)
1.2 (0.047) 1.1 (0.043) 1.3 (0.051)
1.9 (0.075) 1.8 (0.071) 2.2 (0.087)
2.9 (0.114) 2.8 (0.110) 2.4 (0.094)
3.6 (0.142) 3.5 (0.138) 3.5 (0.138)
3.6 (0.142) 3.5 (.0138) 3.5 (0.138)
Notes: (Ref) – Dimensions provided for reference only. No dimensions are provided for B, P or R because low profile cases do not have a bevel or a notch.
* MIL–PRF–55365/8 specified dimensions
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
84
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
2.5
5.5
1.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.9
0.9
0.9
0.9
0.9
1.3
1.3
1.3
1.3
1.3
1.9
1.9
1.9
1.9
1.9
2.7
2.7
2.7
2.7
2.7
4.0
4.0
4.0
4.0
4.0
4.0
6.0
6.0
6.0
6.0
6.0
8.8
% at +20ºC
120 Hz
Maximum
24.0
8.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
10.0
6.0
6.0
6.0
6.0
10.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
10.0
12.0
6.0
6.0
6.0
6.0
30.0
8.0
8.0
10.0
8.0
30.0
30.0
8.0
8.0
8.0
8.0
12.0
8.0
Ω at +20ºC
100 kHz
Maximum
3.9
0.3
4.0
8.0
8.0
6.0
15.0
3.5
4.5
15.0
3.5
4.0
5.0
15.0
1.8
3.0
3.5
5.0
10.0
1.8
1.8
2.5
3.0
5.0
1.6
1.8
2.0
2.5
6.0
0.8
1.5
1.8
1.8
4.0
0.8
1.2
1.8
0.9
4.0
5.0
0.8
1.3
0.7
1.2
2.0
0.7
mA at
+25ºC
100 kHz
134
707
137
97
97
112
63
156
129
63
156
137
118
63
247
168
137
118
77
247
224
184
137
118
262
224
206
173
108
433
271
224
217
137
433
303
224
307
137
118
433
263
423
303
206
423
mA at
+85ºC
100 kHz
121
636
123
87
87
101
57
140
116
57
140
123
106
57
222
151
123
106
69
222
202
166
123
106
236
202
185
156
97
390
244
202
195
123
390
273
202
276
123
106
390
237
381
273
185
381
mA at
+125ºC
100 kHz
54
283
55
39
39
45
25
62
52
25
62
55
47
25
99
67
55
47
31
99
90
74
55
47
105
90
82
69
43
173
108
90
87
55
173
121
90
123
55
47
173
105
169
121
82
169
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
2.5
2.5
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
100
220
33
3.3
4.7
6.8
6.8
10
10
10
15
15
15
15
22
22
22
22
22
33
33
33
33
33
47
47
47
47
47
68
68
68
68
68
100
100
100
100
100
100
150
150
150
150
150
220
T/3528-12
D/7343-31
A/3216-18
A/3216-18
A/3216-18
A/3216-18
S/3216-12
B/3528-21
A/3216-18
S/3216-12
B/3528-21
A/3216-18
T/3528-12
S/3216-12
C/6032-28
B/3528-21
A/3216-18
T/3528-12
S/3216-12
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
D/7343-31
C/6032-28
U/6032-15
B/3528-21
A/3216-18
D/7343-31
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
D/7343-31
U/6032-15
V/7343-20
C/6032-28
B/3528-21
V/7343-20
T491T107(1)2R5A(2)
T491D227(1)2R5A(2)
T491A336(1)003A(2)
T491A335(1)004A(2)
T491A475(1)004A(2)
T491A685(1)004A(2)
T491S685(1)004A(2)
T491B106(1)004A(2)
T491A106(1)004A(2)
T491S106(1)004A(2)
T491B156(1)004A(2)
T491A156(1)004A(2)
T491T156(1)004A(2)
T491S156(1)004A(2)
T491C226(1)004A(2)
T491B226(1)004A(2)
T491A226(1)004A(2)
T491T226(1)004A(2)
T491S226(1)004A(2)
T491C336(1)004A(2)
T491U336(1)004A(2)
T491B336(1)004A(2)
T491A336(1)004A(2)
T491T336(1)004A(2)
T491C476(1)004A(2)
T491U476(1)004A(2)
T491B476(1)004A(2)
T491A476(1)004A(2)
T491T476(M)004A(2)
T491D686(1)004A(2)
T491C686(1)004A(2)
T491U686(1)004A(2)
T491B686(1)004A(2)
T491A686(1)004A(2)
T491D107(1)004A(2)
T491C107(1)004A(2)
T491U107(1)004A(2)
T491B107(M)004A(2)
T491A107(M)004A(2)
T491T107(M)004A(2)
T491D157(1)004A(2)
T491U157(1)004AT
T491V157(1)004A(2)
T491C157(1)004A(2)
T491B157(M)004A(2)
T491V227(1)004A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
95
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
8.8
8.8
8.8
8.8
13.2
13.2
13.2
13.2
18.8
18.8
27.2
27.2
40.0
40.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.9
0.9
0.9
0.9
0.9
1.4
1.4
1.4
1.4
1.4
2.1
2.1
2.1
2.1
2.1
3.0
3.0
3.0
3.0
3.0
3.0
% at +20ºC
120 Hz
Maximum
18.0
15.0
8.0
8.0
8.0
12.0
10.0
8.0
8.0
8.0
12.0
12.0
12.0
15.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
10.0
6.0
6.0
6.0
6.0
15.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
12.0
12.0
6.0
6.0
6.0
6.0
6.0
12.0
Ω at +20ºC
100 kHz
Maximum
0.5
1.2
0.8
0.8
0.7
0.7
0.9
0.8
0.5
0.8
0.5
0.5
0.5
0.2
8.0
7.0
5.5
15.0
3.5
6.0
15.0
3.5
4.0
5.0
15.0
1.8
3.0
3.5
3.5
10.0
1.8
1.8
2.0
3.0
5.0
1.6
1.8
2.2
2.5
6.0
0.8
1.5
1.8
0.7
2.0
3.5
mA at
+25ºC
100 kHz
412
303
433
474
463
423
350
454
574
433
574
548
574
1000
97
97
112
63
156
112
63
156
137
118
63
247
168
146
141
77
247
224
206
158
118
247
224
168
173
108
433
262
224
423
206
146
mA at
+85ºC
100 kHz
371
273
390
427
417
381
315
409
517
390
517
493
517
900
87
87
101
57
140
101
57
140
123
106
57
222
151
131
127
69
222
202
185
142
106
222
202
151
156
97
390
236
202
381
185
131
mA at
+125ºC
100 kHz
165
121
173
190
185
169
140
182
230
173
230
219
230
400
39
39
45
25
62
45
25
62
55
47
25
99
67
58
56
31
99
90
82
63
47
99
90
67
69
43
173
105
90
169
82
58
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
220
220
220
220
330
330
330
330
470
470
680
680
1000
1000
2.2
3.3
4.7
4.7
6.8
6.8
6.8
10
10
10
10
15
15
15
15
15
22
22
22
22
22
33
33
33
33
33
47
47
47
47
47
47
B/3528-21
C/6032-28
D/7343-31
W/7343-15
D/7343-31
V/7343-20
C/6032-28
X/7343-43
X/7343-43
D/7343-31
X/7343-43
D/7343-31
X/7343-43
E/7360-38
A/3216-18
A/3216-18
A/3216-18
S/3216-12
B/3528-21
A/3216-18
S/3216-12
B/3528-21
A/3216-18
T/3528-12
S/3216-12
C/6032-28
B/3528-21
A/3216-18
T/3528-12
S/3216-12
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
D/7343-31
C/6032-28
U/6032-15
V/7343-20
B/3528-21
A/3216-18
T491B227(M)004A(2)
T491C227(1)004AT
T491D227(1)004AT
T491W227(1)004AT
T491D337(1)004A(2)
T491V337(1)004A(2)
T491C337(1)004A(2)
T491X337(1)004AT
T491X477(1)004A(2)
T491D477(1)004A(2)
T491X687(1)004A(2)
T491D687(1)004A(2)
T491X108(1)004A(2)
T491E108(M)004A(2)
T491A225(1)006A(2)
T491A335(1)006A(2)
T491A475(1)006A(2)
T491S475(1)006A(2)
T491B685(1)006A(2)
T491A685(1)006A(2)
T491S685(1)006A(2)
T491B106(1)006A(2)
T491A106(1)006A(2)
T491T106(1)006A(2)
T491S106(1)006A(2)
T491C156(1)006A(2)
T491B156(1)006A(2)
T491A156(1)006A(2)
T491T156(1)006A(2)
T491S156(1)006A(2)
T491C226(1)006A(2)
T491U226(1)006A(2)
T491B226(1)006A(2)
T491A226(1)006A(2)
T491T226(1)006A(2)
T491C336(1)006A(2)
T491U336(1)006A(2)
T491B336(1)006A(2)
T491A336(1)006A(2)
T491T336(1)006A(2)
T491D476(1)006A(2)
T491C476(1)006A(2)
T491U476(1)006A(2)
T491V476(1)006AT
T491B476(1)006A(2)
T491A476(1)006A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
106
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
3.0
4.3
4.3
4.3
4.3
4.3
4.3
6.3
6.3
6.3
6.3
6.3
9.5
9.5
9.5
9.5
9.5
9.5
9.5
13.9
13.9
13.9
13.9
13.9
20.8
20.8
20.8
20.8
20.8
29.6
29.6
29.6
29.6
42.8
42.8
63.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.7
% at +20ºC
120 Hz
Maximum
10.0
6.0
6.0
10.0
6.0
8.0
30.0
8.0
8.0
8.0
10.0
12.0
15.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
10.0
8.0
8.0
12.0
8.0
8.0
8.0
8.0
8.0
12.0
15.0
10.0
15.0
12.0
15.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
Ω at +20ºC
100 kHz
Maximum
2.0
0.8
1.2
1.8
0.7
0.9
4.0
0.8
0.7
0.9
1.8
2.0
3.0
0.7
1.2
0.7
0.6
0.8
0.7
0.7
0.7
1.0
0.7
0.8
1.2
0.7
0.4
0.4
0.5
0.4
0.4
0.7
0.4
0.6
0.5
0.6
10.0
8.0
3.5
7.0
5.5
15.0
3.5
4.0
15.0
3.5
mA at
+25ºC
100 kHz
187
433
303
224
423
307
137
433
423
350
224
206
168
463
303
423
387
474
486
486
463
332
423
474
303
423
642
612
632
642
612
423
707
524
632
524
87
97
156
97
117
63
156
137
63
156
mA at
+85ºC
100 kHz
168
390
273
202
381
276
123
390
381
315
202
185
151
417
273
381
348
427
437
437
417
299
381
427
273
381
578
551
569
578
551
381
636
472
569
472
78
87
140
87
105
57
140
123
57
140
mA at
+125ºC
100 kHz
75
173
121
90
169
123
55
173
169
140
90
82
67
185
121
169
155
190
194
194
185
133
169
190
121
169
257
245
253
257
245
169
283
210
253
210
35
39
62
39
47
25
62
55
25
62
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
10
10
10
10
10
10
10
10
10
10
47
68
68
68
68
68
68
100
100
100
100
100
150
150
150
150
150
150
150
220
220
220
220
220
330
330
330
330
330
470
470
470
470
680
680
1000
1
1.5
2.2
2.2
3.3
3.3
4.7
4.7
4.7
6.8
T/3528-12
D/7343-31
C/6032-28
U/6032-15
V/7343-20
B/3528-21
A/3216-18
D/7343-31
V/7343-20
C/6032-28
U/6032-15
B/3528-21
B/3528-21
D/7343-31
C/6032-28
V/7343-20
U/6032-15
W/7343-15
X/7343-43
X/7343-43
D/7343-31
C/6032-28
V/7343-20
W/7343-15
C/6032-28
V/7343-20
X/7343-43
D/7343-31
E/7360-38
X/7343-43
D/7343-31
V/7343-20
E/7360-38
X/7343-43
E/7360-38
X/7343-43
A/3216-18
A/3216-18
B/3528-21
A/3216-18
A/3216-18
S/3216-12
B/3528-21
A/3216-18
S/3216-12
B/3528-21
T491T476(1)006A(2)
T491D686(1)006A(2)
T491C686(1)006A(2)
T491U686(1)006A(2)
T491V686(1)006AT
T491B686(1)006A(2)
T491A686(1)006A(2)
T491D107(1)006A(2)
T491V107(1)006A(2)
T491C107(1)006A(2)
T491U107(1)006A(2)
T491B107(1)006A(2)
T491B157(M)006A(2)
T491D157(1)006A(2)
T491C157(1)006A(2)
T491V157(1)006A(2)
T491U157(1)006AT
T491W157(1)006AT
T491X157(1)006A(2)
T491X227(1)006A(2)
T491D227(1)006A(2)
T491C227(M)006A(2)
T491V227(1)006A(2)
T491W227(1)006AT
T491C337(1)006A(2)
T491V337(1)006AT
T491X337(1)006A(2)
T491D337(1)006A(2)
T491E337(1)006A(2)
T491X477(1)006A(2)
T491D477(1)006A(2)
T491V477(1)006A(2)
T491E477(1)006A(2)
T491X687(1)006A(2)
T491E687(M)006A(2)
T491X108(1)006AT
T491A105(1)010A(2)
T491A155(1)010A(2)
T491B225(1)010A(2)
T491A225(1)010A(2)
T491A335(1)010A(2)
T491S335(1)010A(2)
T491B475(1)010A(2)
T491A475(1)010A(2)
T491S475(1)010A(2)
T491B685(1)010A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
117
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
0.7
0.7
0.7
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
1.5
2.2
2.2
2.2
2.2
2.2
2.2
3.3
3.3
3.3
3.3
3.3
3.3
3.3
4.7
4.7
4.7
4.7
4.7
6.8
6.8
6.8
6.8
6.8
6.8
10.0
10.0
10.0
10.0
10.0
10.0
15.0
15.0
15.0
% at +20ºC
120 Hz
Maximum
6.0
6.0
10.0
6.0
6.0
6.0
6.0
10.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
6.0
6.0
8.0
12.0
6.0
6.0
6.0
6.0
6.0
24.0
15.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
6.0
10.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
10.0
Ω at +20ºC
100 kHz
Maximum
4.0
5.0
15.0
1.8
3.0
3.8
3.0
15.0
1.8
1.8
2.0
6.0
2.8
0.8
1.6
1.8
2.0
3.2
8.0
0.8
0.7
1.5
1.8
1.8
5.0
6.0
0.8
0.7
1.2
1.4
1.0
0.8
0.7
1.0
1.2
1.8
1.0
1.2
0.7
0.7
0.8
1.0
0.7
0.7
0.7
0.9
mA at
+25ºC
100 kHz
137
118
63
247
156
137
153
63
247
224
206
112
158
433
247
224
206
112
94
433
423
271
224
217
118
112
433
423
303
254
292
433
423
332
387
224
292
266
463
359
474
332
423
486
463
350
mA at
+85ºC
100 kHz
123
106
57
222
140
123
138
57
222
202
185
101
142
390
222
202
185
101
85
390
381
244
202
195
106
101
390
381
273
229
263
390
381
299
348
202
263
239
417
323
427
299
381
437
417
315
mA at
+125ºC
100 kHz
55
47
25
99
62
55
61
25
99
90
82
45
63
173
99
90
82
45
38
173
169
108
90
87
47
45
173
169
121
102
117
173
169
133
155
90
117
106
185
144
190
133
169
194
185
140
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
6.8
6.8
6.8
10
10
10
10
10
15
15
15
15
15
22
22
22
22
22
22
33
33
33
33
33
33
33
47
47
47
47
47
68
68
68
68
68
68
100
100
100
100
100
100
150
150
150
A/3216-18
T/3528-12
S/3216-12
C/6032-28
B/3528-21
A/3216-18
T/3528-12
S/3216-12
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
D/7343-31
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
D/7343-31
V/7343-20
C/6032-28
U/6032-15
B/3528-21
T/3528-12
A/3216-18
D/7343-31
V/7343-20
C/6032-28
U/6032-15
B/3528-21
D/7343-31
V/7343-20
C/6032-28
W/7343-15
U/6032-15
B/3528-21
B/3528-21
D/7343-31
U/6032-15
W/7343-15
C/6032-28
V/7343-20
X/7343-43
D/7343-31
C/6032-28
T491A685(1)010A(2)
T491T685(1)010A(2)
T491S685(1)010A(2)
T491C106(1)010A(2)
T491B106(1)010A(2)
T491A106(1)010A(2)
T491T106(1)010A(2)
T491S106(1)010A(2)
T491C156(1)010A(2)
T491U156(1)010A(2)
T491B156(1)010A(2)
T491A156(1)010A(2)
T491T156(1)010A(2)
T491D226(1)010A(2)
T491C226(1)010A(2)
T491U226(1)010A(2)
T491B226(1)010A(2)
T491A226(1)010A(2)
T491T226(1)010A(2)
T491D336(1)010A(2)
T491V336(1)010A(2)
T491C336(1)010A(2)
T491U336(1)010A(2)
T491B336(1)010A(2)
T491T336(1)010A(2)
T491A336(1)010A(2)
T491D476(1)010A(2)
T491V476(1)010A(2)
T491C476(1)010A(2)
T491U476(1)010A(2)
T491B476(1)010A(2)
T491D686(1)010A(2)
T491V686(1)010A(2)
T491C686(1)010A(2)
T491W686(1)010AT
T491U686(1)010A(2)
T491B686(M)010A(2)
T491B107(1)010A(2)
T491D107(1)010A(2)
T491U107(1)010AT
T491W107(1)010AT
T491C107(1)010A(2)
T491V107(1)010A(2)
T491X157(1)010A(2)
T491D157(1)010A(2)
T491C157(1)010A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
128
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
15.0
22.0
22.0
22.0
22.0
33.0
33.0
33.0
33.0
47
47.0
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
1.1
1.1
1.1
1.6
1.6
1.6
1.6
1.6
2.4
2.4
2.4
2.4
3.5
3.5
3.5
3.5
5.3
5.3
5.3
5.3
7.5
7.5
7.5
10.9
10.9
% at +20ºC
120 Hz
Maximum
8.0
10.0
8.0
8.0
8.0
10.0
12.0
10.0
10.0
10
12.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
8.0
6.0
6.0
10.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
6.0
6.0
Ω at +20ºC
100 kHz
Maximum
0.7
0.9
0.5
0.5
0.7
0.5
0.7
0.5
0.5
0.2
0.5
10.0
8.0
6.0
15.0
3.5
5.0
2.4
3.5
4.0
5.0
1.9
2.5
3.5
1.8
1.8
2.0
3.0
8.0
1.6
1.8
2.0
3.5
0.8
1.5
3.0
2.2
0.8
1.2
1.0
2.0
0.8
0.7
1.0
0.7
1.0
mA at
+25ºC
100 kHz
423
350
574
548
423
548
423
574
632
908
632
87
97
112
63
156
122
214
156
137
118
241
184
146
247
224
206
158
94
247
224
192
146
433
262
173
197
433
303
300
206
433
423
332
423
303
mA at
+85ºC
100 kHz
381
315
517
493
381
493
381
517
569
817.2
569
78
87
101
57
140
110
193
140
123
106
217
166
131
222
202
185
142
85
222
202
173
131
390
236
156
177
390
273
270
185
390
381
299
381
273
mA at
+125ºC
100 kHz
169
140
230
219
169
219
169
230
253
363.2
253
35
39
45
25
62
49
86
62
55
47
96
74
58
99
90
82
63
38
99
90
77
58
173
105
69
79
173
121
120
82
173
169
133
169
121
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
10
10
10
10
10
10
10
10
10
10
10
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
150
220
220
220
220
330
330
330
330
470
470
1
1.5
2.2
2.2
3.3
3.3
4.7
4.7
4.7
4.7
6.8
6.8
6.8
10
10
10
10
10
15
15
15
15
22
22
22
22
33
33
33
33
47
47
47
68
68
V/7343-20
C/6032-28
X/7343-43
D/7343-31
V/7343-20
D/7343-31
V/7343-20
X/7343-43
E/7360-38
X/7343-43
E/7360-38
A/3216-18
A/3216-18
A/3216-18
S/3216-12
B/3528-21
A/3216-18
C/6032-28
B/3528-21
A/3216-18
T/3528-12
C/6032-28
B/3528-21
A/3216-18
C/6032-28
U/6032-15
B/3528-21
A/3216-18
T/3528-12
C/6032-28
U/6032-15
B/3528-21
A/3216-18
D/7343-31
C/6032-28
U/6032-15
B/3528-21
D/7343-31
C/6032-28
U/6032-15
B/3528-21
D/7343-31
V/7343-20
C/6032-28
V/7343-20
C/6032-28
T491V157(1)010A(2)
T491C227(1)010A(2)
T491X227(1)010A(2)
T491D227(1)010A(2)
T491V227(1)010A(2)
T491D337(1)010A(2)
T491V337(1)010A(2)
T491X337(1)010A(2)
T491E337(1)010A(2)
T491X477(1)010A(2)
T491E477(M)010A(2)
T491A105(1)016A(2)
T491A155(1)016A(2)
T491A225(1)016A(2)
T491S225(1)016A(2)
T491B335(1)016A(2)
T491A335(1)016A(2)
T491C475(1)016A(2)
T491B475(1)016A(2)
T491A475(1)016A(2)
T491T475(1)016A(2)
T491C685(1)016A(2)
T491B685(1)016A(2)
T491A685(1)016A(2)
T491C106(1)016A(2)
T491U106(1)016A(2)
T491B106(1)016A(2)
T491A106(1)016A(2)
T491T106(1)016A(2)
T491C156(1)016A(2)
T491U156(1)016A(2)
T491B156(1)016A(2)
T491A156(1)016A(2)
T491D226(1)016A(2)
T491C226(1)016A(2)
T491U226(1)016A(2)
T491B226(1)016A(2)
T491D336(1)016A(2)
T491C336(1)016A(2)
T491U336(1)016A(2)
T491B336(1)016A(2)
T491D476(1)016A(2)
T491V476(1)016A(2)
T491C476(1)016A(2)
T491V686(1)016A(2)
T491C686(1)016AT
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
139
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
10.9
10.9
16.0
16.0
16.0
16.0
24.0
24.0
35.2
35.2
35.2
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.7
0.7
0.7
0.9
0.9
0.9
1.4
1.4
1.4
1.4
2.0
2.0
2.0
2.0
3.0
3.0
3.0
4.4
4.4
4.4
4.4
6.6
6.6
6.6
6.6
9.4
9.4
9.4
% at +20ºC
120 Hz
Maximum
6.0
6.0
8.0
10.0
8.0
8.0
8.0
10.0
15.0
10.0
7.2
4.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
10.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
8.0
10.0
6.0
6.0
6.0
Ω at +20ºC
100 kHz
Maximum
0.8
0.7
0.7
1.0
0.7
0.7
0.5
0.7
0.9
0.5
0.9
12.0
9.0
18.0
6.5
15.0
3.5
6.0
3.0
4.0
5.0
2.4
3.0
4.0
1.9
1.9
2.0
6.0
1.6
1.8
2.0
5.0
1.0
2.0
1.7
0.8
0.7
1.2
4.0
0.8
1.2
0.7
4.0
0.9
0.8
0.7
mA at
+25ºC
100 kHz
474
463
486
332
423
463
574
463
408
574
471
79
91
58
107
63
156
104
168
129
118
214
168
137
241
218
206
112
247
224
201
122
387
206
254
433
423
303
146
433
303
423
146
350
454
463
mA at
+85ºC
100 kHz
427
417
437
299
381
417
517
417
367
517
424
71
82
52
96
57
140
94
151
116
106
193
151
123
217
196
185
101
222
202
181
110
348
185
229
390
381
273
131
390
273
381
131
315
409
417
mA at
+125ºC
100 kHz
190
185
194
133
169
185
230
185
163
230
188
32
36
23
43
25
62
42
67
52
47
86
67
55
96
87
82
45
99
90
80
49
155
82
102
173
169
121
58
173
121
169
58
140
182
185
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
16
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
68
68
100
100
100
100
150
150
220
220
220
0.68
1
1
1.5
1.5
2.2
2.2
3.3
3.3
3.3
4.7
4.7
4.7
6.8
6.8
6.8
6.8
10
10
10
10
15
15
15
22
22
22
22
33
33
33
33
47
47
47
W/7343-15
D/7343-31
X/7343-43
C/6032-28
V/7343-20
D/7343-31
X/7343-43
D/7343-31
D/7343-31
X/7343-43
E/7360-38
A/3216-18
A/3216-18
S/3216-12
A/3216-18
S/3216-12
B/3528-21
A/3216-18
B/3528-21
A/3216-18
T/3528-12
C/6032-28
B/3528-21
A/3216-18
C/6032-28
U/6032-15
B/3528-21
A/3216-18
C/6032-28
U/6032-15
B/3528-21
A/3216-18
D/7343-31
B/3528-21
C/6032-28
D/7343-31
V/7343-20
C/6032-28
B/3528-21
D/7343-31
C/6032-28
V/7343-20
B/3528-21
C/6032-28
X/7343-43
D/7343-31
T491W686(1)016AT
T491D686(1)016A(2)
T491X107(1)016A(2)
T491C107(1)016AT
T491V107(1)016A(2)
T491D107(1)016A(2)
T491X157(1)016A(2)
T491D157(1)016A(2)
T491D227(1)016A(2)
T491X227(1)016A(2)
T491E227(1)016A(2)
T491A684(1)020A(2)
T491A105(1)020A(2)
T491S105(1)020A(2)
T491A155(1)020A(2)
T491S155(1)020A(2)
T491B225(1)020A(2)
T491A225(1)020A(2)
T491B335(1)020A(2)
T491A335(1)020A(2)
T491T335(1)020A(2)
T491C475(1)020A(2)
T491B475(1)020A(2)
T491A475(1)020A(2)
T491C685(1)020A(2)
T491U685(1)020A(2)
T491B685(1)020A(2)
T491A685(1)020A(2)
T491C106(1)020A(2)
T491U106(1)020A(2)
T491B106(1)020A(2)
T491A106(M)020A(2)
T491D156(1)020A(2)
T491B156(1)020AT
T491C156(1)020A(2)
T491D226(1)020A(2)
T491V226(1)020A(2)
T491C226(1)020A(2)
T491B226(1)020A(2)
T491D336(1)020A(2)
T491C336(M)020A(2)
T491V336(1)020A(2)
T491B336(M)020A(2)
T491C476(1)020A(2)
T491X476(1)020AT
T491D476(1)020A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
14
10
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
13.6
13.6
20.0
20.0
20.0
30.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
1.2
1.2
1.2
1.7
1.7
1.7
2.5
2.5
2.5
3.8
3.8
3.8
3.8
5.5
5.5
5.5
8.3
8.3
8.3
11.8
11.8
17.0
17.0
25.0
25.0
0.5
% at +20ºC
120 Hz
Maximum
6.0
6.0
8.0
8.0
8.0
10.0
4.0
4.0
4.0
4.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
10.0
8.0
8.0
4.0
Ω at +20ºC
100 kHz
Maximum
0.7
0.7
0.5
0.9
0.5
0.4
15.0
13.0
10.0
5.0
8.0
18.0
5.0
7.0
3.5
7.0
4.5
2.5
7.0
3.5
2.3
1.5
6.0
1.8
1.9
2.8
1.0
1.5
2.0
1.0
1.0
1.5
4.0
0.8
1.0
0.7
0.7
0.7
0.9
0.7
0.7
0.7
0.7
0.3
0.5
20.0
mA at
+25ºC
100 kHz
486
463
574
408
632
642
71
76
87
130
97
58
130
104
177
104
137
210
104
156
214
238
112
289
241
174
387
271
168
387
354
271
146
433
280
423
486
463
350
486
463
486
463
742
632
61
mA at
+85ºC
100 kHz
437
417
517
367
569
578
64
68
78
117
87
52
117
94
159
94
123
189
94
140
193
214
101
260
217
157
348
244
151
348
319
244
131
390
252
381
437
417
315
437
417
437
417
668
569
55
mA at
+125ºC
100 kHz
194
185
230
163
253
257
28
30
35
52
39
23
52
42
71
42
55
84
42
62
86
95
45
116
96
70
155
108
67
155
142
108
58
173
112
169
194
185
140
194
185
194
185
297
253
24
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
35
68
68
100
100
100
150
0.33
0.47
0.68
1
1
1
1.5
1.5
2.2
2.2
2.2
3.3
3.3
3.3
4.7
4.7
4.7
6.8
6.8
6.8
10
10
10
15
15
15
15
22
22
22
33
33
33
47
47
68
68
100
100
0.1
X/7343-43
D/7343-31
X/7343-43
D/7343-31
E/7360-38
X/7343-43
A/3216-18
A/3216-18
A/3216-18
B/3528-21
A/3216-18
S/3216-12
B/3528-21
A/3216-18
C/6032-28
A/3216-18
B/3528-21
C/6032-28
A/3216-18
B/3528-21
C/6032-28
B/3528-21
A/3216-18
D/7343-31
C/6032-28
B/3528-21
D/7343-31
C/6032-28
B/3528-21
D/7343-31
V/7343-20
C/6032-28
B/3528-21
D/7343-31
C/6032-28
V/7343-20
X/7343-43
D/7343-31
C/6032-28
X/7343-43
D/7343-31
X/7343-43
D/7343-31
X/7343-43
E/7360-38
A/3216-18
T491X686(1)020A(2)
T491D686(1)020A(2)
T491X107(1)020A(2)
T491D107(1)020AT
T491E107(1)020A(2)
T491X157(1)020A(2)
T491A334(1)025A(2)
T491A474(1)025A(2)
T491A684(1)025A(2)
T491B105(1)025A(2)
T491A105(1)025A(2)
T491S105(1)025A(2)
T491B155(1)025A(2)
T491A155(1)025A(2)
T491C225(1)025A(2)
T491A225(1)025A(2)
T491B225(1)025A(2)
T491C335(1)025A(2)
T491A335(1)025A(2)
T491B335(1)025A(2)
T491C475(1)025A(2)
T491B475(1)025A(2)
T491A475(1)025A(2)
T491D685(1)025A(2)
T491C685(1)025A(2)
T491B685(1)025A(2)
T491D106(1)025A(2)
T491C106(1)025A(2)
T491B106(1)025A(2)
T491D156(1)025A(2)
T491V156(1)025AT
T491C156(1)025A(2)
T491B156(1)025A(2)
T491D226(1)025A(2)
T491C226(1)025A(2)
T491V226(1)025A(2)
T491X336(1)025A(2)
T491D336(1)025A(2)
T491C336(1)025A(2)
T491X476(1)025A(2)
T491D476(1)025A(2)
T491X686(1)025A(2)
T491D686(M)025A(2)
T491X107(1)025A(2)
T491E107(1)025A(2)
T491A104(1)035A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
15
11
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
1.2
1.2
1.6
1.6
1.6
2.4
2.4
2.4
3.5
3.5
3.5
5.3
5.3
5.3
7.7
7.7
11.6
11.6
16.5
16.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
% at +20ºC
120 Hz
Maximum
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
10.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
Ω at +20ºC
100 kHz
Maximum
19.0
18.0
15.0
8.0
11.0
6.5
8.0
5.0
7.0
7.0
4.5
5.0
3.2
4.0
4.0
2.0
3.5
1.5
3.0
2.0
1.2
1.2
1.8
1.0
1.6
1.0
1.0
0.9
0.8
0.7
0.7
0.6
0.6
0.6
0.5
20.0
16.0
15.0
14.0
18.0
14.0
10.0
9.5
7.2
9.0
8.0
mA at
+25ºC
100 kHz
63
65
71
103
79
114
97
130
100
104
156
130
185
129
146
235
156
316
166
224
340
323
247
387
262
250
332
428
433
486
463
524
500
524
632
61
73
71
78
65
73
92
280
117
97
97
mA at
+85ºC
100 kHz
57
59
64
93
71
103
87
117
90
94
140
117
167
116
131
212
140
284
149
202
306
291
222
348
236
225
299
385
390
437
417
472
450
472
569
55
66
64
70
59
66
83
253
105
87
87
mA at
+125ºC
100 kHz
25
26
28
41
32
46
39
52
40
42
62
52
74
52
58
94
62
126
66
90
136
129
99
155
105
100
133
171
173
194
185
210
200
210
253
24
29
28
31
26
29
37
112
47
39
39
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
50
50
50
50
50
50
50
50
50
50
50
0.15
0.22
0.33
0.47
0.47
0.68
0.68
1
1
1.5
1.5
1.5
2.2
2.2
2.2
3.3
3.3
4.7
4.7
4.7
6.8
6.8
6.8
10
10
10
15
15
15
22
22
33
33
47
47
0.1
0.15
0.15
0.22
0.22
0.33
0.33
0.47
0.47
0.47
0.68
A/3216-18
A/3216-18
A/3216-18
B/3528-21
A/3216-18
B/3528-21
A/3216-18
B/3528-21
A/3216-18
A/3216-18
C/6032-28
B/3528-21
C/6032-28
A/3216-18
B/3528-21
C/6032-28
B/3528-21
D/7343-31
B/3528-21
C/6032-28
D/7343-31
V/7343-20
C/6032-28
D/7343-31
C/6032-28
V/7343-20
C/6032-28
X/7343-43
D/7343-31
X/7343-43
D/7343-31
X/7343-43
D/7343-31
X/7343-43
E/7360-38
A/3216-18
B/3528-21
A/3216-18
B/3528-21
A/3216-18
A/3216-18
B/3528-21
A/3216-18
C/6032-28
B/3528-21
A/3216-18
T491A154(1)035A(2)
T491A224(1)035A(2)
T491A334(1)035A(2)
T491B474(1)035A(2)
T491A474(1)035A(2)
T491B684(1)035A(2)
T491A684(1)035A(2)
T491B105(1)035A(2)
T491A105(1)035A(2)
T491A155(1)035A(2)
T491C155(1)035A(2)
T491B155(1)035A(2)
T491C225(1)035A(2)
T491A225(1)035AT
T491B225(1)035A(2)
T491C335(1)035A(2)
T491B335(1)035A(2)
T491D475(1)035A(2)
T491B475(1)035AT
T491C475(1)035A(2)
T491D685(1)035A(2)
T491V685(1)035AT
T491C685(1)035A(2)
T491D106(1)035A(2)
T491C106(1)035A(2)
T491V106(1)035A(2)
T491C156(1)035A(2)
T491X156(1)035A(2)
T491D156(1)035A(2)
T491X226(1)035A(2)
T491D226(1)035A(2)
T491X336(1)035A(2)
T491D336(1)035A(2)
T491X476(1)035A(2)
T491E476(1)035A(2)
T491A104(1)050A(2)
T491B154(1)050A(2)
T491A154(1)050A(2)
T491B224(1)050A(2)
T491A224(1)050AT
T491A334(1)050A(2)
T491B334(1)050A(2)
T491A474(1)050A(2)
T491C474(1)050A(2)
T491B474(1)050A(2)
T491A684(1)050A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
16
12
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated Rated Case Code/
Voltage Cap
Case Size
KEMET Part
Number
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
0.68
0.68
1
1
1
1
1.5
1.5
2.2
2.2
3.3
3.3
4.7
6.8
6.8
10
10
15
22
C/6032-28
B/3528-21
A/3216-18
C/6032-28
B/3528-21
V/7343-20
D/7343-31
C/6032-28
D/7343-31
C/6032-28
C/6032-28
D/7343-31
D/7343-31
X/7343-43
D/7343-31
X/7343-43
D/7343-31
X/7343-43
X/7343-43
T491C684(1)050A(2)
T491B684(1)050A(2)
T491A105(1)050A(2)
T491C105(1)050A(2)
T491B105(1)050A(2)
T491V105(1)050A(2)
T491D155(1)050A(2)
T491C155(1)050A(2)
T491D225(1)050A(2)
T491C225(1)050A(2)
T491C335(1)050AT
T491D335(1)050A(2)
T491D475(1)050A(2)
T491X685(1)050A(2)
T491D685(1)050A(2)
T491X106(1)050A(2)
T491D106(1)050A(2)
T491X156(1)050A(2)
T491X226(1)050A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
DF
ESR
µA at +20ºC
Maximum/
5 Minutes
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
1.1
1.1
1.7
1.7
2.4
3.4
3.4
5.0
5.0
7.5
11.0
µA at +20ºC
Maximum/
5 Minutes
% at +20ºC
120 Hz
Maximum
4.0
4.0
4.0
4.0
6.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
10.0
% at +20ºC
120 Hz
Maximum
Ω at +20ºC
100 kHz
Maximum
6.4
8.0
7.0
4.8
6.0
6.0
3.5
4.0
2.5
3.0
2.0
1.6
1.2
0.8
0.8
0.7
0.8
0.7
0.6
Ω at +20ºC
100 kHz
Maximum
DC
Leakage
DF
ESR
Maximum Allowable
Ripple Current
mA at
+25ºC
100 kHz
125
103
104
148
119
144
207
166
245
191
235
274
354
406
387
486
433
486
524
mA at
+25ºC
100 kHz
mA at
+85ºC
100 kHz
113
93
94
133
107
130
186
149
221
172
212
247
319
365
348
437
390
437
472
mA at
+85ºC
100 kHz
mA at
+125ºC
100 kHz
50
41
42
59
48
58
83
66
98
76
94
110
142
162
155
194
173
194
210
mA at
+125ºC
100 kHz
Maximum Allowable
Ripple Current
Maximum
Operating
Temp
MSL
ºC
Reflow Temp
≤ 260 ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ºC
Reflow Temp
≤ 260 ºC
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum), N = NonMagnetic 100% Tin (Sn), M = Non-Magnetic (SnPb). Designates Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
17
13
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Recommended Voltage Derating Guidelines
85°C to 125°C
120%
VR
67% of VR
100%
50% of VR
33% of VR
% Working Voltage
% Change in Working DC
Voltage with Temperature
Recommended Maximum
Application Voltage
-55°C to 85°C
80%
60%
40%
20%
0%
% Change in Working DC Voltage
with Temperature
67%
Recommended Maximum
Application Voltage (As %
of Rated Voltage)
-55
25
33%
85
Temperature (ºC)
125
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent
series resistance (ESR) and the power dissipation capabilities of
the device. Permissible AC ripple voltage which may be applied is
limited by two criteria:
1. The positive peak AC voltage plus the DC bias voltage, if any,
must not exceed the DC voltage rating of the capacitor.
2. The negative peak AC voltage in combination with bias
voltage, if any, must not exceed the allowable limits specified for
reverse voltage. See the Reverse Voltage section for allowable
limits.
The maximum power dissipation by case size can be determined
using the table at right. The maximum power dissipation rating
stated in the table must be reduced with increasing environmental
operating temperatures. Refer to the table below for temperature
compensation requirements.
Temperature Compensation Multipliers
for Maximum Ripple Current
T ≤ 25°C
1.00
T ≤ 85°C
0.90
T ≤ 125°C
0.40
KEMET
Case Code
EIA
Case Code
A
B
C
D
X
E
S
T
U
V
W
T510X
T510E
3216–18
3528–21
6032–28
7343–31
7343–43
7360–38
3216–12
3528–12
6032–15
7343–20
7343-15
7343–43
7360–38
Maximum Power
Dissipation (P max)
mWatts at 25°C
w/+20°C Rise
75
85
110
150
165
200
60
70
90
125
180
270
285
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature Compensation
Multiplier table for details.
T= Environmental Temperature
Using the P max of the device, the maximum allowable rms ripple
current or voltage may be determined.
I(max) = √P max/R
E(max) = Z √P max/R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P max = maximum power dissipation (watts)
R = ESR at specified frequency (ohms)
Z = Impedance at specified frequency (ohms)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
18
14
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Reverse Voltage
Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The
positive terminal is identified on the capacitor body by a stripe plus in some cases a beveled edge. A small degree of transient reverse
voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within
these limits.
Temperature
Permissible Transient Reverse Voltage
25°C
85°C
125°C
15% of Rated Voltage
5% of Rated Voltage
1% of Rated Voltage
Table 2 – Land Dimensions/Courtyard
KEMET
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
Case
EIA
W
L
S
V1
V2
W
L
S
V1
V2
W
L
S
V1
V2
A
3216–18
1.35
2.20
0.62
6.02
2.80
1.23
1.80
0.82
4.92
2.30
1.13
1.42
0.98
4.06
2.04
B
3528–21
2.35
2.21
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
C
6032–25
2.35
2.77
2.37
8.92
4.50
2.23
2.37
2.57
7.82
4.00
2.13
1.99
2.73
6.96
3.74
D
7343–31
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
E1
7360–38
4.25
2.77
3.67
10.22
7.30
4.13
2.37
3.87
9.12
6.80
4.03
1.99
4.03
8.26
6.54
S2
3216–12
1.35
2.20
0.62
6.02
2.80
1.23
1.80
0.82
4.92
2.30
1.13
1.42
0.98
4.06
2.04
T
3528–12
2.35
2.20
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
U
6032–15
2.35
2.77
2.37
8.92
4.50
2.23
2.37
2.57
7.82
4.00
2.13
1.99
2.73
6.96
3.74
V
7343–20
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
W
7343–15
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
X1
7343–43
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
2
Land pattern geometry is too small for silkscreen outline.
V1
L
L
W
W
V2
S
Grid Placement Courtyard
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
19
15
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Soldering Process
Please note that although the X/7343–43 case size can withstand
wave soldering, the tall profile (4.3 mm maximum) dictates care in
wave process development.
Hand soldering should be performed with care due to the difficulty
in process control. If performed, care should be taken to avoid
contact of the soldering iron to the molded case. The iron should
be used to heat the solder pad, applying solder between the pad
and the termination, until reflow occurs. Once reflow occurs, the
iron should be removed immediately. “Wiping” the edges of a chip
and heating the top surface is not recommended.
During typical reflow operations, a slight darkening of the goldcolored epoxy may be observed. This slight darkening is normal
and not harmful to the product. Marking permanency is not
affected by this change.
Profile Feature
SnPb Assembly Pb-Free Assembly
Preheat/Soak
Temperature Minimum (TSmin)
100°C
150°C
Temperature Maximum (TSmax)
150°C
200°C
Time (ts) from Tsmin to Tsmax)
60 – 120 seconds
60 – 120 seconds
Ramp-up Rate (TL to TP)
3°C/seconds maximum
3°C/seconds maximum
Liquidous Temperature (TL)
183°C
217°C
Time Above Liquidous (t L)
60 – 150 seconds
220°C*
235°C**
60 – 150 seconds
250°C*
260°C**
Peak Temperature (TP)
Time within 5°C of Maximum
Peak Temperature (tP)
Ramp-down Rate (TP to TL)
20 seconds maximum
30 seconds maximum
6°C/seconds maximum
6°C/seconds maximum
Time 25°C to Peak Temperature
6 minutes maximum
8 minutes maximum
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reflow.
*Case Size D, E, P, Y, and X
**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z
TP
TL
Temperature
KEMET’s families of surface mount capacitors are compatible
with wave (single or dual), convection, IR, or vapor phase reflow
techniques. Preheating of these components is recommended
to avoid extreme thermal stress. KEMET's recommended profile
conditions for convection and IR reflow reflect the profile conditions
of the IPC/J–STD–020D standard for moisture sensitivity testing.
The devices can safely withstand a maximum of three reflow
passes at these conditions.
tP
Maximum Ramp Up Rate = 3ºC/seconds
Maximum Ramp Down Rate = 6ºC/seconds
tL
Tsmax
Tsmin
25
tS
25ºC to Peak
Time
Storage
Tantalum chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 60%
relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulphur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within three years
of receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
20
16
Tantalum Surface Mount Capacitors – Standard Tantalum
T491 Series Industrial Grade MnO2
Construction
Polarity Stripe (+)
Molded Epoxy
Case
Detailed Cross Section
Silver Paint
(Fourth Layer)
Polarity
Bevel (+)
Tantalum Wire
Leadframe
(- Cathode)
Washer
Tantalum Wire
Weld
(to attach wire)
Carbon
(Third Layer)
Silver Adhesive
Leadframe
(+ Anode)
Molded Epoxy
Case
MnO2
(Second Layer)
Washer
Ta2O5 Dielectric
(First Layer)
Tantalum
Capacitor Marking
Date Code *
KEMET
Industrial
Grade MnO2
Polarity
Indicator (+)
1 digit = Last number of Year
9 = 2009
0 = 2010
1 = 2011
2 = 2012
3 = 2013
4 = 2014
2nd and 3rd digit = Week of the Year
01 = 1st week of the Year to
52 = 52nd week of the Year
st
Picofarad
Code
KEMET
ID
Rated
Voltage
Date
Code*
* 230 = 30th week of 2012
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2005_T491
TC101_STD • 5/7/2015
21
17
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Overview
The KEMET T489 Series provides DC leakage current that is
25% lower than the commercial T491 Series. The T489 Series
also offers improved reliability, low ESR options and meets
or exceeds the requirements of EIA standard 535BAAC. This
series is classified as MSL (Moisture Sensitivity Level) 1 under
J STD 020: unlimited floor life time at ≤30°C/85% RH. The
T489 standard terminations are available in 100% matte tin
and provide excellent wetting characteristics and compatibility
with today's surface mount solder systems. Tin/lead (Sn/Pb)
terminations are available upon request for any part number.
Gold-plated terminations are also available for use with conductive
epoxy attachment processes. Standard packaging of these
devices is tape and reel in accordance with EIA 481. This system
provides perfect compatibility with all tape-fed placement units.
Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
DC Leakage at 0.0075 CV
Improved reliability: 0.50%/1,000 hours, 85°C, rated voltage
Low ESR options available
Meets or exceeds EIA standard 535BAAC
Taped and reeled per EIA 481
Symmetrical, compliant terminations
Laser-marked case
Halogen-free epoxy
Capacitance values of 0.1 μF to 470 μF
Tolerances of ±10% and ±20%
Voltage rating of 6.3 – 50 VDC
RoHS Compliant and lead-free terminations
Operating temperature range of -55˚C to +125˚C
Applications
Typical applications include decoupling and filtering in industrial and automotive high end applications.
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
221
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
SPICE
For a detailed analysis of specific part numbers, please visit www.kemet.com for a free download of KEMET's SPICE software. The
KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions.
Ordering Information
T
489
B
156
M
Capacitor
Class
Series
Case Size
Capacitance
Code (pF)
Capacitance
Tolerance
Low DC
Leakage
Series
A, B, C,
D, X
T=
Tantalum
First two digits represent
significant figures. Third
digit specifies number of
zeros.
K = ±10%
M = ±20%
16
A
T
E800
Termination Finish
ESR
T = 100% Matte Tin
(Sn) Plated
H = Standard Solder
Coated (SnPb 5% Pb
minimum)
G = Gold Plated
Last three digits
specify ESR in mΩ.
(800 = 800 mΩ)
Rated Voltage Failure Rate/
(VDC)
Design
006 = 6.3
010 = 10
016 = 16
020 = 20
025 = 25
035 = 35
050 = 50
A = N/A
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
-55°C to 125°C
0.10 µF to 470 µF at 120 Hz/25°C
K Tolerance (±10%), M Tolerance (±20%)
6.3 – 50 V
DF(120 Hz)
Refer to Part Number Electrical Specification
ESR (100 kHz)
Refer to Part Number Electrical Specification
Leakage Current
Reliability
≤ 0.0075 CV (µA) at rated voltage after 5 minutes
0.50%/1,000 hours at 85°C, VR with 0.1 Ω series resistance
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
232
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Qualification
Test
Condition
Characteristics
Δ C/C
Endurance
Storage Life
Thermal Shock
Temperature Stability
85°C at rated voltage, 2,000 hours
125°C at 2/3 rated voltage, 2,000 hours
125°C at 0 volts, 2,000 hours
MIL–STD–202, Method 107, Condition B, mounted, -55C° to
125° C, 1,000 cycles
Extreme temperature exposure at a
succession of continuous steps at +25ºC,
-55ºC, +25ºC, +85ºC, +125ºC, +25ºC
DF
Within initial limits
DCL
Within 1.25 x initial limit
ESR
Within initial limits
Δ C/C
Within ±10% of initial value
DF
Within initial limits
DCL
Within 1.25 x initial limit
ESR
Within initial limits
Δ C/C
Within ±5% of initial value
DF
Within initial limits
DCL
Within 1.25 x initial limit
ESR
Within initial limits
+25°C
-55°C
+85°C
+125°C
Δ C/C
IL*
±10%
±10%
±20%
DF
IL
IL
1.5 x IL
1.5 x IL
DCL
IL
N/A
10 x IL
12 x IL
Δ C/C
Surge Voltage
Mechanical Shock/Vibration
Within ±10% of initial value
85°C, 1.32 x rated voltage 1,000 cycles
(125°C, 1.2 x rated voltage)
MIL–STD–202, Method 213, Condition I, 100 G peak.
MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz,
20 G peak
Within ±5% of initial value
DF
Within initial limits
DCL
Within initial limits
ESR
Within initial limits
Δ C/C
Within ±10% of initial value
DF
Within initial limits
DCL
Within initial limits
*IL = Initial limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
243
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Dimensions – Millimeters (Inches)
Metric will govern
CATHODE (-) END VIEW
SIDE VIEW
ANODE (+) END VIEW
BOTTOM VIEW
A
B
W
B
H
X
T
S
G
S
Termination cutout
at KEMET's option,
either end
Case Size
KEMET
EIA
F
E
P
R
L
Component
L*
W*
H*
F* ±0.1 S* ±0.3 B* ±0.15
±(0.004) ±(0.012) (Ref) ±0.006
A
3.2 ±0.2
1.6 ±0.2
1.6 ±0.2
3216–18 (0.126
±0.008) (0.063 ±0.008) (0.063 ±0.008) 1.2 (0.047) 0.8 (0.031)
X (Ref)
P (Ref)
R (Ref)
T (Ref)
A (Min) G (Ref) E (Ref)
0.4 (0.016)
0.10 ±0.10
(0.004 ±0.004) 0.4 (0.016)
0.4 (0.016) 0.13 (0.005) 0.8 (0.31) 1.1 (0.043) 1.3 (0.051)
B
3.5 ±0.2
2.8 ±0.2
1.9 ±0.2
3528–21 (0.138
±0.008) (0.110 ±0.008) (0.075 ±0.008) 2.2 (0.087) 0.8 (0.031)
0.4 (0.016)
0.10 ±0.10
(0.004 ±0.004) 0.5 (0.020)
1.0 (0.039) 0.13 (0.005) 1.1 (0.043) 1.8 (0.071) 2.2 (0.087)
C
6.0 ±0.3
3.2 ±0.3
2.5 ±0.3
6032–28 (0.236
±0.012) (0.126 ±0.012) (0.098 ±0.012) 2.2 (0.087) 1.3 (0.051)
0.5 (0.020)
0.10 ±0.10
(0.004 ±0.004) 0.9 (0.035)
1.0 (0.039) 0.13 (0.005) 2.5(0.098) 2.8 (0.110) 2.4 (0.094)
D
7.3 ±0.3
4.3 ±0.3
2.8 ±0.3
7343–31 (0.287
±0.012) (0.169 ±0.012) (0.110 ±0.012) 2.4 (0.094) 1.3 (0.051)
0.5 (0.020)
0.10 ±0.10
(0.004 ±0.004) 0.9 (0.035)
1.0 (0.039) 0.13 (0.005) 3.8 (0.150) 3.5 (0.138) 3.5 (0.138)
X
7.3 ±0.3
4.3 ±0.3
4.0 ±0.3
7343–43 (0.287
±0.012) (0.169 ±0.012) (0.157 ±0.012) 2.4 (0.094) 1.3 (0.051)
0.5 (0.020)
0.10 ±0.10
(0.004 ±0.004) 1.7 (0.067)
1.0 (0.039) 0.13 (0.005) 3.8 (0.150) 3.5 (0.138) 3.5 (0.138)
* MIL–PRF–55365/8 specified dimensions
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
254
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Table 1 – Ratings & Part Number Reference
Rated
Voltage
Rated
Case Code/
Capacitance Case Size
KEMET Part
Number
DC
Leakage
DF
% at +25ºC
120 Hz
Maximum
6.0
6.0
6.0
6.0
15.0
6.0
8.0
8.0
6.0
8.0
8.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
8.0
6.0
8.0
8.0
8.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
12.0
% at +25ºC
120 Hz
Maximum
DF
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
10
15
22
47
150
100
150
100
150
220
470
2.2
4.7
6.8
6.8
10
15
15
22
33
33
33
47
47
68
100
100
150
220
330
1
2.2
3.3
4.7
6.8
6.8
10
10
15
22
22
22
33
47
47
68
100
150
B/3528-21
A/3216-18
C/6032-28
B/3528-21
B/3528-21
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
A/3216-18
A/3216-18
A/3216-18
B/3528-21
A/3216-18
B/3528-21
C/6032-28
B/3528-21
B/3528-21
C/6032-28
D/7343-31
C/6032-28
D/7343-31
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
A/3216-18
A/3216-18
B/3528-21
B/3528-21
B/3528-21
C/6032-28
B/3528-21
C/6032-28
B/3528-21
B/3528-21
C/6032-28
D/7343-31
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
D/7343-31
T489B106(1)006A(2)
T489A156(1)006A(2)
T489C226(1)006A(2)
T489B476(1)006A(2)
T489B157(1)006A(2)
T489C107(1)006A(2)
T489C157(1)006A(2)
T489D107(1)006A(2)
T489D157(1)006A(2)
T489D227(1)006A(2)
T489X477(1)006A(2)
T489A225(1)010A(2)
T489A475(1)010A(2)
T489A685(1)010A(2)
T489B685(1)010A(2)
T489A106(1)010A(2)
T489B156(1)010A(2)
T489C156(1)010A(2)
T489B226(1)010A(2)
T489B336(1)010A(2)
T489C336(1)010A(2)
T489D336(1)010A(2)
T489C476(1)010A(2)
T489D476(1)010A(2)
T489C686(1)010A(2)
T489C107(1)010A(2)
T489D107(1)010A(2)
T489D157(1)010A(2)
T489D227(1)010A(2)
T489X337(1)010A(2)
T489A105(1)016A(2)
T489A225(1)016A(2)
T489B335(1)016A(2)
T489B475(1)016A(2)
T489B685(1)016A(2)
T489C685(1)016A(2)
T489B106(1)016A(2)
T489C106(1)016A(2)
T489B156(1)016A(2)
T489B226(1)016A(2)
T489C226(1)016A(2)
T489D226(1)016A(2)
T489C336(1)016A(2)
T489C476(1)016A(2)
T489D476(1)016A(2)
T489D686(1)016A(2)
T489D107(1)016A(2)
T489D157(1)016A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +25ºC
Maximum/
5 Minutes
0.5
0.7
1.0
2.2
7.1
4.7
7.1
4.7
7.1
10.4
22.2
0.5
0.5
0.5
0.5
0.8
1.1
1.1
1.7
2.5
2.5
2.5
3.5
3.5
5.1
7.5
7.5
11.3
16.5
24.8
0.5
0.5
0.5
0.6
0.8
0.8
1.2
1.2
1.8
2.6
2.6
2.6
4.0
5.6
5.6
8.2
12.0
18.0
µA at +25ºC
Maximum/
5 Minutes
Rated
Voltage
Rated
Capacitance
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
Standard ESR
mΩ at +25ºC
100 kHz
Maximum
3000
2030
2000
1620
3000
440
500
800
400
360
250
7000
2900
2650
3000
2200
2030
2000
1880
1000
590
1100
540
400
490
500
440
400
500
300
10000
4550
4500
3160
2650
2500
2200
2000
2030
1100
700
1100
590
540
540
490
440
700
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
E3K0
E2K0
E2K0
E1K6
E3K0
E440
E500
E800
E400
E360
E250
E7K0
E2K9
E2K6
E3K0
E2K2
E2K0
E2K0
E1K8
E1K0
E590
E1K1
E540
E400
E490
E500
E440
E400
E500
E300
E10K
E4K5
E4K5
E3K1
E2K6
E2K5
E2K2
E2K0
E2K0
E1K1
E700
E1K1
E590
E540
E540
E490
E440
E700
E-Spec Code
Standard ESR
Low ESR
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
1500
E1K5
500
E500
300
E300
150
150
200
E150
E150
E200
1800
E1K8
700
650
E700
E650
150
150
E150
E150
100
E100
3500
E3K5
800
600
350
E800
E600
E350
350
200
150
150
E350
E200
E150
E150
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
Low ESR
Maximum
Operating
Temp
ºC
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
ºC
Maximum
Operating
Temp
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates Capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates
Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
265
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated
Voltage
Rated
Case Code/
Capacitance Case Size
KEMET Part
Number
DC
Leakage
DF
% at +25ºC
120 Hz
Maximum
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
4.0
4.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
4.0
4.0
4.0
4.0
4.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
% at +25ºC
120 Hz
Maximum
DF
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
1
1.5
2.2
3.3
3.3
4.7
6.8
6.8
10
10
15
15
22
33
33
47
68
100
0.47
0.68
1
2.2
3.3
4.7
6.8
6.8
10
10
15
15
22
33
47
0.1
0.22
0.33
1
1
1.5
2.2
3.3
3.3
4.7
4.7
6.8
6.8
10
10
A/3216-18
A/3216-18
A/3216-18
A/3216-18
B/3528-21
B/3528-21
B/3528-21
C/6032-28
B/3528-21
C/6032-28
C/6032-28
D/7343-31
D/7343-31
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
A/3216-18
A/3216-18
A/3216-18
B/3528-21
B/3528-21
B/3528-21
B/3528-21
C/6032-28
C/6032-28
D/7343-31
C/6032-28
D/7343-31
D/7343-31
D/7343-31
D/7343-31
A/3216-18
A/3216-18
A/3216-18
A/3216-18
B/3528-21
B/3528-21
B/3528-21
B/3528-21
C/6032-28
C/6032-28
D/7343-31
C/6032-28
D/7343-31
C/6032-28
D/7343-31
T489A105(1)020A(2)
T489A155(1)020A(2)
T489A225(1)020A(2)
T489A335(1)020A(2)
T489B335(1)020A(2)
T489B475(1)020A(2)
T489B685(1)020A(2)
T489C685(1)020A(2)
T489B106(1)020A(2)
T489C106(1)020A(2)
T489C156(1)020A(2)
T489D156(1)020A(2)
T489D226(1)020A(2)
T489C336(1)020A(2)
T489D336(1)020A(2)
T489D476(1)020A(2)
T489D686(1)020A(2)
T489X107(1)020A(2)
T489A474(1)025A(2)
T489A684(1)025A(2)
T489A105(1)025A(2)
T489B225(1)025A(2)
T489B335(1)025A(2)
T489B475(1)025A(2)
T489B685(1)025A(2)
T489C685(1)025A(2)
T489C106(1)025A(2)
T489D106(1)025A(2)
T489C156(1)025A(2)
T489D156(1)025A(2)
T489D226(1)025A(2)
T489D336(1)025A(2)
T489D476(1)025A(2)
T489A104(1)035A(2)
T489A224(1)035A(2)
T489A334(1)035A(2)
T489A105(1)035A(2)
T489B105(1)035A(2)
T489B155(1)035A(2)
T489B225(1)035A(2)
T489B335(1)035A(2)
T489C335(1)035A(2)
T489C475(1)035A(2)
T489D475(1)035A(2)
T489C685(1)035A(2)
T489D685(1)035A(2)
T489C106(1)035A(2)
T489D106(1)035A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +25ºC
Maximum/
5 Minutes
0.5
0.5
0.5
0.5
0.5
0.7
1.0
1.0
1.5
1.5
2.3
2.3
3.3
5.0
5.0
7.1
10.2
15.0
0.5
0.5
0.5
0.5
0.6
0.9
1.3
1.3
1.9
1.9
2.8
2.8
4.1
6.2
8.8
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.9
0.9
1.2
1.2
1.8
1.8
2.6
2.6
µA at +25ºC
Maximum/
5 Minutes
Rated
Voltage
Rated
Capacitance
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
Standard ESR
mΩ at +25ºC
100 kHz
Maximum
6630
5460
4550
3740
3740
3160
2650
2000
2200
800
720
1100
650
590
590
540
490
300
9530
7980
6630
4550
3740
3160
1500
1070
800
1200
720
720
650
590
540
20000
13710
11280
6630
3400
5460
4550
3740
1840
1410
1500
1070
1300
800
800
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
E6K6
E5K4
E4K5
E3K7
E3K7
E3K1
E2K6
E2K0
E2K2
E800
E720
E1K1
E650
E590
E590
E540
E490
E300
E9K5
E7K9
E6K6
E4K5
E3K7
E3K1
E1K5
E1K0
E800
E1K2
E720
E720
E650
E590
E540
E20K
E13K
E11K
E6K6
E3K4
E5K4
E4K5
E3K7
E1K8
E1K4
E1K5
E1K0
E1K3
E800
E800
E-Spec Code
Standard ESR
Low ESR
Maximum
Operating
Temp
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
3500
E3K5
1000
500
400
E1K0
E500
E400
300
300
250
200
200
150
7000
E300
E300
E250
E200
E200
E150
E7K0
2000
1000
1000
600
600
E2K0
E1K0
E1K0
E600
E600
300
300
400
250
E300
E300
E400
E250
3000
2000
2500
2000
E3K0
E2K0
E2K5
E2K0
800
600
E800
E600
600
E600
600
400
mΩ at +25ºC
100 kHz
Maximum
E600
E400
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
E-Spec Code
ºC
Low ESR
ºC
Maximum
Operating
Temp
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates Capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates
Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
276
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Table 1 – Ratings & Part Number Reference cont'd
Rated
Voltage
Rated
Case Code/
Capacitance Case Size
KEMET Part
Number
DC
Leakage
DF
% at +25ºC
120 Hz
Maximum
6.0
6.0
4.0
4.0
4.0
4.0
6.0
6.0
4.5
4.5
4.5
4.5
% at +25ºC
120 Hz
Maximum
DF
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
35
35
50
50
50
50
50
50
50
50
50
50
15
22
0.22
0.33
0.68
1
1.5
2.2
2.2
3.3
4.7
6.8
D/7343-31
D/7343-31
A/3216-18
A/3216-18
B/3528-21
C/6032-28
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
D/7343-31
T489D156(1)035A(2)
T489D226(1)035A(2)
T489A224(1)050A(2)
T489A334(1)050A(2)
T489B684(1)050A(2)
T489C105(1)050A(2)
T489C155(1)050A(2)
T489C225(1)050A(2)
T489D225(1)050A(2)
T489D335(1)050A(2)
T489D475(1)050A(2)
T489D685(1)050A(2)
VDC at 85ºC
µF
KEMET/EIA
(See below for
part options)
µA at +25ºC
Maximum/
5 Minutes
3.9
5.8
0.5
0.5
0.5
0.5
0.6
0.8
0.8
1.2
1.8
2.6
µA at +25ºC
Maximum/
5 Minutes
Rated
Voltage
Rated
Capacitance
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
Standard ESR
mΩ at +25ºC
100 kHz
Maximum
720
650
7500
7000
4000
3000
2500
1700
2000
1100
900
700
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
E720
E650
E7K5
E7K0
E4K0
E3K0
E2K5
E1K7
E2K0
E1K1
E900
E700
E-Spec Code
Standard ESR
Low ESR
mΩ at +25ºC
100 kHz
Maximum
350
300
7000
Maximum
Operating
Temp
E-Spec Code
ºC
E350
E300
E7K0
125
125
125
125
125
125
125
125
125
125
125
125
2000
E2K0
1500
1000
1200
800
600
E1K5
E1K0
E1K2
E800
E600
mΩ at +25ºC
100 kHz
Maximum
E-Spec Code
Low ESR
ºC
Maximum
Operating
Temp
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates Capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates
Termination Finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
287
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Recommended Voltage Derating Guidelines
85°C to 125°C
120%
VR
67% of VR
100%
50% of VR
33% of VR
% Working Voltage
% Change in Working DC
Voltage with Temperature
Recommended Maximum
Application Voltage
-55°C to 85°C
80%
60%
40%
20%
0%
% Change in Working DC Voltage
with Temperature
67%
Recommended Maximum
Application Voltage (As %
of Rated Voltage)
-55
25
33%
85
Temperature (ºC)
125
Ripple Current/Ripple Voltage
KEMET Series
and Case Code
EIA
Case Code
A
B
C
D
X
E
S
T
U
V
T510X
T510E
3216–18
3528–21
6032–28
7343–31
7343–43
7360–38
3216–12
3528–12
6032–15
7343–20
7343–43
7360–38
Maximum Power
Dissipation (P max)
mWatts at 25°C
w/+20°C Rise
75
85
110
150
165
200
60
70
90
125
270
285
Temperature Compensation Multipliers
for Maximum Ripple Current
T ≤ 25°C
1.00
T ≤ 85°C
0.90
T ≤ 125°C
0.40
T= Environmental Temperature
Using the P max of the device, the maximum allowable rms ripple
current or voltage may be determined.
I(max) = √P max/R
E(max) = Z √P max/R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
Pmax = maximum power dissipation (watts)
R = ESR at specified frequency (ohms)
Z = Impedance at specified frequency (ohms)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
298
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Reverse Voltage
Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The
positive terminal is identified on the capacitor body by a stripe plus in some cases a beveled edge. A small degree of transient reverse
voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within
these limits.
Temperature
Permissible Transient Reverse Voltage
25°C
85°C
125°C
15% of Rated Voltage
5% of Rated Voltage
1% of Rated Voltage
Table 2 – Land Dimensions/Courtyard
KEMET
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
Case
EIA
W
L
S
V1
V2
W
L
S
V1
V2
W
L
S
V1
V2
A
3216–18
1.35
2.20
0.62
6.02
2.80
1.23
1.80
0.82
4.92
2.30
1.13
1.42
0.98
4.06
2.04
B
3528–21
2.35
2.21
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
C
6032–25
2.35
2.77
2.37
8.92
4.50
2.23
2.37
2.57
7.82
4.00
2.13
1.99
2.73
6.96
3.74
D
7343–31
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
X1
7343–43
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
2
Land pattern geometry is too small for silkscreen outline.
V1
L
L
W
W
V2
S
Grid Placement Courtyard
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
309
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Soldering Process
Please note that although the X/7343–43 case size can withstand
wave soldering, the tall profile (4.3 mm maximum) dictates care in
wave process development.
Hand soldering should be performed with care due to the difficulty
in process control. If performed, care should be taken to avoid
contact of the soldering iron to the molded case. The iron should
be used to heat the solder pad, applying solder between the pad
and the termination, until reflow occurs. Once reflow occurs, the
iron should be removed immediately. “Wiping” the edges of a chip
and heating the top surface is not recommended.
During typical reflow operations, a slight darkening of the goldcolored epoxy may be observed. This slight darkening is normal
and not harmful to the product. Marking permanency is not
affected by this change.
Profile Feature
SnPb Assembly Pb-Free Assembly
Preheat/Soak
Temperature Minimum (TSmin)
100°C
150°C
Temperature Maximum (TSmax)
150°C
200°C
Time (ts) from Tsmin to Tsmax)
60 – 120 seconds
60 – 120 seconds
3°C/seconds maximum
Ramp-up Rate (TL to TP)
3°C/seconds maximum
Liquidous Temperature (TL)
183°C
217°C
Time Above Liquidous (t L)
60 – 150 seconds
220°C*
235°C**
60 – 150 seconds
250°C*
260°C**
Peak Temperature (TP)
Time within 5°C of Maximum
Peak Temperature (tP)
Ramp-down Rate (TP to TL)
20 seconds maximum
30 seconds maximum
6°C/seconds maximum
6°C/seconds maximum
Time 25°C to Peak Temperature
6 minutes maximum
8 minutes maximum
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reflow.
*Case Size D, E, P, Y, and X
**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z
TP
TL
Temperature
KEMET’s families of surface mount capacitors are compatible
with wave (single or dual), convection, IR, or vapor phase reflow
techniques. Preheating of these components is recommended
to avoid extreme thermal stress. KEMET's recommended profile
conditions for convection and IR reflow reflect the profile conditions
of the IPC/J–STD–020D standard for moisture sensitivity testing.
The devices can safely withstand a maximum of three reflow
passes at these conditions.
tP
Maximum Ramp Up Rate = 3ºC/seconds
Maximum Ramp Down Rate = 6ºC/seconds
tL
Tsmax
Tsmin
25
tS
25ºC to Peak
Time
Storage
Tantalum chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 60%
relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulphur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within three years
of receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
31
10
Tantalum Surface Mount Capacitors – Standard Tantalum
T489 Series Low DC Leakage MnO2
Construction
Polarity Stripe (+)
Molded Epoxy
Case
Detailed Cross Section
Silver Paint
(Fourth Layer)
Polarity
Bevel (+)
Tantalum Wire
Leadframe
(- Cathode)
Washer
Tantalum Wire
Weld
(to attach wire)
Carbon
(Third Layer)
Silver Adhesive
Leadframe
(+ Anode)
Molded Epoxy
Case
MnO2
(Second Layer)
Washer
Ta2O5 Dielectric
(First Layer)
Tantalum
Capacitor Marking
Date Code *
KEMET
Industrial
Grade MnO2
Polarity
Indicator (+)
1 digit = Last number of Year
9 = 2009
0 = 2010
1 = 2011
2 = 2012
3 = 2013
4 = 2014
2nd and 3rd digit = Week of the Year
01 = 1st week of the Year to
52 = 52nd week of the Year
st
Picofarad
Code
KEMET
ID
Rated
Voltage
Date
Code*
* 230 = 30th week of 2012
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2024_T489
TC101_STD • 5/7/2015
32
11
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Overview
The KEMET T490 Series, designed for customer product
applications (low temperature demanding applications), meets
RoHS compliance with leads constructed of 100% matte tin
and green molding compound. This series is classified as MSL
(Moisture Sensitivity Level) 1 under J STD 020: unlimited floor
life time at ≤30°C / 85% RH. Tin/lead (Sn/Pb) terminations
are available upon request for any part number. Gold-plated
terminations are also available for use with conductive epoxy
attachment processes. Standard packaging of these devices is
tape and reel in accordance with EIA 481. This system provides
perfect compatibility with all tape-fed placement units.
Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Taped and reeled per EIA 481
Symmetrical compliant terminations
Optional gold-plated terminations
Laser-marked case
Suitable for 3 x 260°C reflow passes
Halogen-free epoxy
Capacitance values of 47 μF to 470 μF
Tolerance of ±20%
Voltage rating of 4 – 10 VDC
0.2% per 1,000 hours at 85ºC 0.5 VR Reliability
Small and low profile case sizes
RoHS Compliant and lead-free terminations
MSL Reflow Temp ≤ 260ºC = 1
Operating temperature range of -55˚C to +40˚C
Applications
Typical applications include decoupling and filtering in communications end applications such as cellphones and consumer mobile.
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
331
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
SPICE
For a detailed analysis of specific part numbers, please visit www.kemet.com for a free download of KEMET's SPICE software.
The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over
frequency, temperature, ripple, and DC bias conditions.
Ordering Information
T
490
B
227
M
Capacitor
Class
Series
Case Size
Capacitance
Code (pF)
Capacitance
Tolerance
Industrial
A, B, T
First two digits
represent significant
figures. Third digit
specifies number of
zeros.
M = ±20%
T=
Tantalum
006
A
Rated Voltage Failure Rate/
(VDC)
Design
004 = 4
006 = 6.3
010 = 10
A = N/A
T
Termination Finish
T = 100% Matte Tin (Sn)
plated
H = Standard solder
coated (SnPb 5% Pb
minimum)
G = Gold plated (A, B
only)
Packaging (C-Spec)
Blank = 7" Reel
7280 = 13" Reel
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
ESR (100 kHz)
Leakage Current
-55°C to 40°C
47 – 470 µF at 120 Hz/25°C
M Tolerance (20%)
4 – 10 V
Refer to Part Number Electrical Specification Table
≤ 0.01 CV (μA) at rated voltage after 5 minutes
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
342
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Qualification
Test
Condition
Endurance
Storage Life
Humidity
Temperature Stability
Surge Voltage
Characteristics
40°C at 1.0 VR 85°C at 1/2 VR and 125°C at 1/5 rated
voltage, 1,000 hours
85°C at 0 volts, 1,000 hours
40°C, 93% RH, 1,000 hours, no load
Extreme temperature exposure at a
succession of continuous steps at +25°C,
-55°C, +25°C, +85°C, +125°C, +25°C
40°C, 1.32 x rated voltage 1,000 cycles
Δ C/C
Within +10%/- 20% of initial value
DCL
Within 2 x initial limit
ESR
Within 2.5 x initial limits
Δ C/C
Within +10%/- 20% of initial value
DCL
Within 1.25 x initial limit
ESR
Within initial limits
Δ C/C
Within -5%/+35% of initial value
DCL
Within 2.0 x initial limit
+25°C
-55°C
+85°C
+125°C
Δ C/C
IL*
±10%
±20%
±30%
DCL
IL
N/A
10 x IL
15 x IL
Δ C/C
Within +10%/- 20% of initial value
DCL
Within 2.0 x initial limits
ESR
Within 1.25 x initial limits
*IL = Initial limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
353
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Electrical Characteristics
ESR vs. Frequency
Impedance & ESR (Ohms)
100
490A107/006 Imp
490B227/006 Imp
490B337/004 Imp
490A107/006 ESR
490B227/006 ESR
490B337/004 ESR
10
1
0.1
100
1,000
10,000
100,000
Frequency (Hz)
1,000,000
10,000,000
Capacitance vs. Frequency
1,000.0
490A107/006 Cap
490B227/006 Cap
490B337/004 Cap
Capacitance (µF)
100.0
10.0
1.0
0.1
100
1,000
10,000
Frequency (Hz)
100,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
1,000,000
T2004_T490
TC101_STD • 5/7/2015
364
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Dimensions – Millimeters (Inches)
Metric will govern
CATHODE (-) END VIEW
SIDE VIEW
ANODE (+) END VIEW
BOTTOM VIEW
A
B
W
B
H
X
T
S
G
S
Termination cutout
at KEMET's option,
either end
Case Size
KEMET
EIA
F
E
P
R
L
Component
L*
W*
H*
F* ±0.1
±(.004)
S*
B* ±0.15
(Ref) ±.006
X (Ref)
P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref)
A
3.2 ±0.2
1.6 ±0.2
1.6 ±0.2
0.80 (0.032) + 0.2
3216-18 (0.126
±0.008) (0.063 ±0.008) (0.063 ±0.008) 1.2 (0.047) (0.008)/-0.3 (0.011)
0.4 (.016)
0.10 ±0.10
(0.004 ±0.004) 0.4 (0.016) 0.4 (0.016) 0.13 (.005) 1.2 (0.047) 1.1 (0.043) 1.3 (0.051)
B
3.5 ±0.2
2.8 ±0.2
1.9 ±0.2
0.80 (0.032) + 0.2
3528-21 (0.138
±0.008) (0.110 ±0.008) (0.075 ±0.008) 2.2 (0.087) (0.008)/-0.3 (0.011)
0.4 (.016)
0.10 ±0.10
(0.004 ±0.004) 0.5 (0.020) 1.0 (0.039) 0.13 (.005) 1.9 (0.075) 1.8 (0.071) 2.2 (0.087)
T
3.5 ±0.2
2.8 ±0.2
3528-12 (0.138
±0.008) (0.110 ±0.008)
1.2 (0.047)
0.80 (0.032) + 0.2
2.2 (0.087) (0.008)/-0.3
(0.011)
N/A
0.05 (0.002)
N/A
N/A
0.13 (.005) 1.9 (0.075) 1.8 (0.071) 2.2 (0.087)
Notes: (Ref) – Dimensions provided for reference only. No dimensions are provided for B, P or R because low profile cases do not have a bevel or a notch.
* MIL–PRF–55365/8 specified dimensions
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
375
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Table 1 – Ratings & Part Number Reference
Rated
Rated
Case Code/
Voltage Capacitance Case Size
KEMET Part
Number
DC
Leakage
ESR
µA at +20ºC
Maximum/
5 Minutes
4.0
6.0
6.0
8.8
13.2
18.8
2.8
4.1
4.1
6.0
6.0
6.0
9.0
9.0
13.2
13.2
19.8
4.7
4.7
15.0
15.0
22.0
Ω at +20ºC
100 kHz
Maximum
0.5
0.8
1.1
0.5
0.8
1.0
0.8
1.0
0.6
0.5
0.8
1.0
0.5
0.8
0.3
0.5
0.8
1.0
1.0
0.5
0.8
0.8
Maximum
Allowable
Ripple Current
Maximum
Operating
Temp
mA at +25ºC
100 kHz
ºC
387
306
252
412
326
291
295
274
342
387
306
265
412
326
532
412
326
265
274
412
326
326
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
MSL
Reflow
Temp
≤ 260 ºC
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
VDC at 40ºC
µF
KEMET/EIA
(See below for
part options)
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
100
150
150
220
330
470
47
68
68
100
100
100
150
150
220
220
330
47
47
150
150
220
A/3216-18
A/3216-18
T/3528-12
B/3528-21
B/3528-21
B/3528-21
T/3528-12
A/3216-18
T/3528-12
A/3216-18
A/3216-18
T/3528-12
B/3528-21
B/3528-21
B/3528-21
B/3528-21
B/3528-21
T/3528-12
A/3216-18
B/3528-21
B/3528-21
B/3528-21
T490A107M004A(1)E500
T490A157M004A(1)E800
T490T157M004A(1)E1K1
T490B227M004A(1)E500
T490B337M004A(1)E800
T490B477M004A(1)E1K0
T490T476M006A(1)E800
T490A686M006A(1)E1K0
T490T686M006A(1)E600
T490A107M006A(1)E500
T490A107M006A(1)E800
T490T107M006A(1)E1K0
T490B157M006A(1)E500
T490B157M006A(1)E800
T490B227M006A(1)E300
T490B227M006A(1)E500
T490B337M006A(1)E800
T490T476M010A(1)E1K0
T490A476M010A(1)E1K0
T490B157M010A(1)E500
T490B157M010A(1)E800
T490B227M010A(1)E800
VDC at 40ºC
µF
KEMET/EIA
(See below for
part options)
µA at +20ºC
Maximum/
5 Minutes
Ω at +20ºC
100 kHz
Maximum
mA at +25ºC
100 kHz
ºC
Reflow
Temp
≤ 260 ºC
Rated
Voltage
Rated
Capacitance
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
ESR
Maximum
Allowable
Ripple Current
Maximum
Operating
Temp
MSL
(1) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates
termination finish.
Blue color text denotes "Under Development"
Refer to Ordering Information for additional detail.
The ESR value may increase up to 1.5 x Initial Limit post mounting
The DCL value may increase up to 2.0 x Initial Limit post mounting
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked
with the higher voltage rating. Substitutions can include better than series.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
386
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Recommended Voltage Derating Guidelines
-55°C to 40°C
100% of VR
VR
100%
50% of VR
VR
80%
40°C to 85°C
% Change in Working DC
Voltage with Temperature
Recommended Maximum
Application Voltage
50% of VR
VR
50% of VR
VR
85°C to 125°C
% Change in Working DC
Voltage with Temperature
Recommended Maximum
Application Voltage
% Working Voltage
% Change in Working DC
Voltage with Temperature
Recommended Maximum
Application Voltage
Recommended Voltage Derating Guidelines
120%
60%
50%
40%
VR
20% of VR
VR
Recommended Maximum
Application Voltage
20%
0%
20% of VR
% Change in Working DC
Voltage with Temperature
-55
25
20%
40
85
105
125
Temperature (°C)
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent
series resistance (ESR) and the power dissipation capabilities of
the device. Permissible AC ripple voltage which may be applied is
limited by two criteria:
1. The positive peak AC voltage plus the DC bias voltage, if any,
must not exceed the DC voltage rating of the capacitor.
2. The negative peak AC voltage in combination with bias
voltage, if any, must not exceed the allowable limits specified for
reverse voltage. See the Reverse Voltage section for allowable
limits.
The maximum power dissipation by case size can be determined
using the table at right. The maximum power dissipation rating
stated in the table must be reduced with increasing environmental
operating temperatures. Refer to the table below for temperature
compensation requirements.
Temperature Compensation Multipliers
for Maximum Ripple Current
T ≤ 25°C
1.00
T= Environmental Temperature
T ≤ 40°C
0.90
T ≤ 85°C
0.40
KEMET
Case Code
EIA
Case Code
A
B
T
3216–18
3528–21
3528–12
Maximum Power
Dissipation (P max)
mWatts at 25°C
w/+20°C Rise
75
85
70
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature Compensation
Multiplier table for details.
Using the P max of the device, the maximum allowable rms ripple
current or voltage may be determined.
I(max) = √P max/R
E(max) = Z √P max/R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P max = maximum power dissipation (watts)
R = ESR at specified frequency (ohms)
Z = Impedance at specified frequency (ohms)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
397
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Reverse Voltage
Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The
positive terminal is identified on the capacitor body by a stripe plus in some cases a beveled edge. A small degree of transient reverse
voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within
these limits.
Temperature
Permissible Transient Reverse Voltage
25°C
40°C
85°C
15% of Rated Voltage
5% of Rated Voltage
1% of Rated Voltage
Table 2 – Land Dimensions/Courtyard
KEMET
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
Case
EIA
W
L
S
V1
V2
W
L
S
V1
V2
W
L
S
V1
V2
A
3216–18
1.35
2.20
0.62
6.02
2.80
1.23
1.80
0.82
4.92
2.30
1.13
1.42
0.98
4.06
2.04
B
3528–21
2.35
2.21
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
T
3528–12
2.35
2.20
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
2
Land pattern geometry is too small for silkscreen outline.
V1
L
L
W
W
V2
S
Grid Placement Courtyard
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
408
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Soldering Process
Please note that although the X/7343–43 case size can withstand
wave soldering, the tall profile (4.3 mm maximum) dictates care in
wave process development.
Hand soldering should be performed with care due to the difficulty
in process control. If performed, care should be taken to avoid
contact of the soldering iron to the molded case. The iron should
be used to heat the solder pad, applying solder between the pad
and the termination, until reflow occurs. Once reflow occurs, the
iron should be removed immediately. “Wiping” the edges of a chip
and heating the top surface is not recommended.
During typical reflow operations, a slight darkening of the goldcolored epoxy may be observed. This slight darkening is normal
and not harmful to the product. Marking permanency is not
affected by this change.
Profile Feature
SnPb Assembly Pb-Free Assembly
Preheat/Soak
Temperature Minimum (TSmin)
100°C
150°C
Temperature Maximum (TSmax)
150°C
200°C
Time (ts) from Tsmin to Tsmax)
60 – 120 seconds
60 – 120 seconds
3°C/seconds maximum
Ramp-up Rate (TL to TP)
3°C/seconds maximum
Liquidous Temperature (TL)
183°C
217°C
Time Above Liquidous (t L)
60 – 150 seconds
220°C*
235°C**
60 – 150 seconds
250°C*
260°C**
Peak Temperature (TP)
Time within 5°C of Maximum
Peak Temperature (tP)
Ramp-down Rate (TP to TL)
20 seconds maximum
30 seconds maximum
6°C/seconds maximum
6°C/seconds maximum
Time 25°C to Peak Temperature
6 minutes maximum
8 minutes maximum
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reflow.
*Case Size D, E, P, Y, and X
**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z
TP
TL
Temperature
KEMET’s families of surface mount capacitors are compatible
with wave (single or dual), convection, IR, or vapor phase reflow
techniques. Preheating of these components is recommended
to avoid extreme thermal stress. KEMET's recommended profile
conditions for convection and IR reflow reflect the profile conditions
of the IPC/J–STD–020D standard for moisture sensitivity testing.
The devices can safely withstand a maximum of three reflow
passes at these conditions.
tP
Maximum Ramp Up Rate = 3ºC/seconds
Maximum Ramp Down Rate = 6ºC/seconds
tL
Tsmax
Tsmin
25
tS
25ºC to Peak
Time
Storage
Tantalum chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 60%
relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulphur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within three years
of receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
419
Tantalum Surface Mount Capacitors – Standard Tantalum
T490 Series Commercial Grade MnO2
Construction
Molded Epoxy
Case
Detailed Cross Section
Polarity Stripe (+)
Silver Paint
(Fourth Layer)
Tantalum Wire
Leadframe
(- Cathode)
Washer
Tantalum Wire
Weld
(to attach wire)
Carbon
(Third Layer)
Silver Adhesive
Leadframe
(+ Anode)
Molded Epoxy
Case
MnO2
(Second Layer)
Washer
Ta2O5 Dielectric
(First Layer)
Tantalum
Capacitor Marking
KEMET
Industrial
Grade MnO2
Polarity
Indicator (+)
Date Code *
1 digit = Last number of Year
9 = 2009
0 = 2010
1 = 2011
2 = 2012
3 = 2013
4 = 2014
2nd and 3rd digit = Week of the Year
01 = 1st week of the Year to
52 = 52nd week of the Year
st
Picofarad
Code
KEMET
ID
Rated
Voltage
Date
Code*
* 230 = 30th week of 2012
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
www.kemet.com
T2004_T490
TC101_STD • 5/7/2015
42
10
Tantalum Surface Mount Capacitors – Standard Tantalum
Tape & Reel Packaging Information
KEMET’s molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in
accordance with EIA Standard 481: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging
system is compatible with all tape-fed automatic pick-and-place systems.
8 mm (0.315")
or
12 mm (0.472")
Top Tape Thickness
0.10 mm (0.004")
Maximum Thickness
180 mm (7.0")
or
330 mm (13.0")
Table 3 – Packaging Quantity
Case Code
KEMET
S
T
M
U
L
W
Z
V
A
B
C
D
Q
Y
X
E/T428P
H
EIA
3216-12
3528-12
3528-15
6032-15
6032-19
7343-15
7343-17
7343-20
3216-18
3528-21
6032-28
7343-31
7343-12
7343-40
7343-43
7360-38
7360-20
Tape Width
(mm)
7" Reel*
13" Reel*
8
8
8
12
12
12
12
12
8
8
12
12
12
12
12
12
12
2,500
2,500
2,000
1,000
1,000
1,000
1,000
1,000
2,000
2,000
500
500
1,000
500
500
500
1,000
10,000
10,000
8,000
5,000
3,000
3,000
3,000
3,000
9,000
8,000
3,000
2,500
3,000
2,000
2,000
2,000
2,500
* No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
43
Tantalum Surface Mount Capacitors – Standard Tantalum
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
P2
T
T2
ØDo
Po
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
E1
Ao
F
Ko
B1
S1
W
E2
Bo
P1
T1
Center Lines of Cavity
B 1 is for tape feeder reference only,
including draft concentric about B o.
Embossment
For cavity size,
see Note 1 Table 4
ØD 1
Cover Tape
User Direction of Unreeling
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
D0
8 mm
12 mm
1.5 +0.10/-0.0
(0.059 +0.004/-0.0)
16 mm
D1 Minimum
Note 1
1.0
(0.039)
1.5
(0.059)
B1 Maximum
Note 4
4.35
(0.171)
E1
P0
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
P2
2.0 ±0.05
(0.079 ±0.002)
2.0 ±0.1
(0.079 ±0.059)
R Reference
Note 2
25.0
(0.984)
30
(1.181)
S1 Minimum
T Maximum T1 Maximum
Note 3
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
Variable Dimensions — Millimeters (Inches)
Tape Size
Pitch
E2 Minimum
F
8 mm
Single (4 mm)
6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
12 mm
Single (4 mm) &
Double (8 mm)
8.2
(0.323)
10.25
(0.404)
16 mm
Triple (12 mm)
12.1
(0.476)
14.25
(0.561)
P1
2.0 ±0.05 or 4.0 ±0.10
(0.079 ±0.002 or 0.157 ±0.004)
2.0 ±0.05 (0.079 ±0.002) or 4.0
5.5 ±0.05
±0.10 (0.157 ±0.004) or 8.0 ±0.10
(0.217 ±0.002)
(0.315 ±0.004)
7.5±0.10
4.0 ±0.10 (0.157 ±0.004) to 12.0
(0.295 ±0.004)
±0.10 (0.472 ±0.004)
T2 Maximum
W Maximum A0, B0 & K0
2.5
(0.098)
8.3
(0.327)
4.6
(0.181)
12.3
(0.484)
8.0 (0.315)
16.3
(0.642)
Note 5
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 4).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
44
Tantalum Surface Mount Capacitors – Standard Tantalum
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
Peel Strength
8 mm
0.1 to 1.0 Newton (10 to 100 gf)
12 and 16 mm
0.1 to 1.3 Newton (10 to 130 gf)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 2 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Width (mm)
8,12
16 – 200
Bo
Maximum
Rotation (
20
10
°
T)
Typical Component Centerline
Ao
Figure 3 – Maximum Lateral Movement
8 mm & 12 mm Tape
0.5 mm maximum
0.5 mm maximum
16 mm Tape
°
s
Tape
Maximum
Width (mm) Rotation (
8,12
20
16 – 56
10
72 – 200
5
°
S)
Figure 4 – Bending Radius
Embossed
Carrier
Punched
Carrier
1.0 mm maximum
1.0 mm maximum
R
Bending
Radius
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
R
TC101_STD • 5/7/2015
45
Tantalum Surface Mount Capacitors – Standard Tantalum
Figure 5 – Reel Dimensions
Full Radius,
See Note
W3 (Includes
Access Hole at
Slot Location
(Ø 40 mm minimum)
flange distortion
at outer edge)
W2 (Measured at hub)
D
A
(See Note)
N
C
(Arbor hole
diameter)
B
(see Note)
W1 (Measured at hub)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 5 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
A
B Minimum
C
D Minimum
8 mm
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size
N Minimum
W1
W2 Maximum
W3
50
(1.969)
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
12.4 +2.0/-0.0
(0.488 +0.078/-0.0)
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
14.4
(0.567)
18.4
(0.724)
22.4
(0.882)
Shall accommodate tape width
without interference
8 mm
12 mm
16 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
46
Tantalum Surface Mount Capacitors – Standard Tantalum
Figure 6 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Punched Carrier
8 mm & 12 mm only
END
Round Sprocket Holes
START
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
Trailer
160 mm Minimum
Components
100 mm
Minimum Leader
400 mm Minimum
Top Cover Tape
Figure 7 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
47
Tantalum Surface Mount Capacitors – Standard Tantalum
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel: 39-051-939111
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Skopje, Macedonia
Tel: 389-2-55-14-623
Shenzhen, China
Tel: 86-755-2518-1306
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Kamen, Germany
Tel: 49-2307-438110
North America
Northern Europe
Harlow, United Kingdom
Tel: 44-1279-460122
Taipei, Taiwan
Tel: 886-2-27528585
Espoo, Finland
Tel: 358-9-5406-5000
Southeast Asia
Singapore
Tel: 65-6701-8033
2835 KEMET Way
Simpsonville, SC 29681
Southeast
Lake Mary, FL
Tel: 407-855-8886
Northeast
Wilmington, MA
Tel: 978-658-1663
Central
Novi, MI
Tel: 248-306-9353
Beijing, China
Tel: 86-10-5877-1075
Shanghai, China
Tel: 86-21-6447-0707
Seoul, South Korea
Tel: 82-2-6294-0550
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
48
Tantalum Surface Mount Capacitors – Standard Tantalum
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
TC101_STD • 5/7/2015
49
Corporate Office
KEMET Corporation
2835 KEMET Way
Simpsonville, SC 29681
USA
Tel: 864.963.6300
Fax: 864.963.6521
www.kemet.com
One world. One KEMET.
Electronic Components