B-XMD-1W&D-XMD

B-XMD-1W&D-XMD-1W Series
1KV Isolated 1W unregulated single & dual separated output DIP8 DC
DC⁄⁄DC Converter
SELECTION GUIDE
Model
INPUT
VOLTAGE
(V)
OUTPUT
VOLTAGE
(V)
OUTPUT
CURRENT
MAX
(mA)
B0503XMD-1W
4.5-5.5
3.3
B0505XMD-1W
4.5-5.5
5
B0507XMD-1W
4.5-5.5
B0509XMD-1W
ISOIATION
(VDC)
MAX
CAPACTIVE
Load
EFFICIEN
CY
(% )
300
1000
220
72
200
1000
220
75
7.2
140
1000
220
76
4.5-5.5
9
110
1000
220
77
B0512XMD-1W
4.5-5.5
12
83
1000
220
78
B0515XMD-1W
4.5-5.5
15
67
1000
220
78
B0518XMD-1W
4.5-5.5
18
56
1000
220
78
B0524XMD-1W
4.5-5.5
24
42
1000
220
78
B1203XMD-1W
10.8-13.2
3.3
300
1000
220
72
B1205XMD-1W
10.8-13.2
5
200
1000
220
75
B1207XMD-1W
10.8-13.2
7.2
140
1000
220
76
Short circuit protection(automatic recovery)
B1209XMD-1W
10.8-13.2
9
110
1000
220
77
No external component required
B1212XMD-1W
10.8-13.2
12
83
1000
220
78
B1215XMD-1W
10.8-13.2
15
67
1000
220
78
B1218XMD-1W
10.8-13.2
18
56
1000
220
78
B1224XMD-1W
10.8-13.2
24
42
1000
220
78
B2403XMD-1W
21.6-26.4
3.3
300
1000
220
72
B2405XMD-1W
21.6-26.4
5
200
1000
220
75
B2407XMD-1W
21.6-26.4
7.2
140
1000
220
76
B2409XMD-1W
21.6-26.4
9
110
1000
220
77
B 05 05 X MD -1W(100)
B2412XMD-1W
21.6-26.4
12
83
1000
220
78
B2415XMD-1W
21.6-26.4
15
67
1000
220
78
①Product Series
②Input Voltage
③Output Voltage
④Fixed Input
⑤MINI DIP8 Package
⑥Rated Power(Output current)
B2418XMD-1W
21.6-26.4
18
56
1000
220
78
B2424XMD-1W
21.6-26.4
24
42
1000
220
78
D050303XMD-1W
4.5-5.5
3.3 / 3.3
150 / 150
1000
220
63
D050505XMD-1W
4.5-5.5
5/5
100 / 100
1000
220
72
D050707XMD-1W
4.5-5.5
7.2 / 7.2
70 / 70
1000
220
75
D050909XMD-1W
4.5-5.5
9/9
55 / 55
1000
220
78
APPLICATIONS
D051212XMD-1W
4.5-5.5
12 / 12
42 / 42
1000
220
80
The B-XMD-1W&D-XMD-1W series are
specially designed for applications where a
group of polar power supplies are isolated from
the input power supply in a distributed power
supply system on a circuit board.
These products apply to:
1) where the voltage of the input power supply is
fixed (voltage variation ≤±10%);
2) where isolation is necessary between input
and output (isolation voltage ≤1000VDC);
3) where the regulation of the output voltage
and the output ripple noise are not demanded.
D051515XMD-1W
4.5-5.5
15 / 15
34 / 34
1000
220
80
D051818XMD-1W
4.5-5.5
18 / 18
28 / 28
1000
220
78
D052424XMD-1W
4.5-5.5
24 / 24
21 / 21
1000
220
78
D120303XMD-1W
10.8-13.2
3.3 / 3.3
150 / 150
1000
220
70
D120505XMD-1W
10.8-13.2
5/5
100 / 100
1000
220
72
D120707XMD-1W
10.8-13.2
7.2 / 7.2
70 / 70
1000
220
71
D120909XMD-1W
10.8-13.2
9/9
55 / 55
1000
220
76
D121212XMD-1W
10.8-13.2
12 / 12
42 / 42
1000
220
80
D121515XMD-1W
10.8-13.2
15 / 15
34 / 34
1000
220
80
D121818XMD-1W
10.8-13.2
18 / 18
28 / 28
1000
220
76
D122424XMD-1W
10.8-13.2
24 / 24
21 / 21
1000
220
78
D240303XMD-1W
21.6-26.4
3.3 / 3.3
150 / 150
1000
220
76
D240505XMD-1W
21.6-26.4
5/5
100 / 100
1000
220
72
D240707XMD-1W
21.6-26.4
7.2 / 7.2
70 / 70
1000
220
73
D240909XMD-1W
21.6-26.4
9/9
55 / 55
1000
220
77
D241212XMD-1W
21.6-26.4
12 / 12
42 / 42
1000
220
82
D241515XMD-1W
21.6-26.4
15 / 15
34 / 34
1000
220
82
D241818XMD-1W
21.6-26.4
18 / 18
28 / 28
1000
220
75
D242424XMD-1W
21.6-26.4
24 / 24
21 / 21
1000
220
80
FEATURES
8 Pin DIP Package
◆
Low ripple and noise
◆
High efficiency up to 82%
◆
Input / Output Isolation 1000VDC
◆
Pin compatible with multiple manufactures
◆
Operating temperature -40℃ to + 85℃
◆
◆
◆
MTBF>1,000,000 hours
◆
RoHS Compliance
◆
MODEL SELECTION
①
②
③
④
⑤
⑥
MICRODC RESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 3
B-XMD-1W&D-XMD-1W Series
Input Specifications
Parameters
Voltage range
Nominal
Typical
5
4.5-5.5
VDC
12
10.8-13.2
VDC
24
21.6-26.4
Filter
Maximum
Units
VDC
Capacitor
Turn on Transient process time
25
Start up time
Absolute Maximum Rating
ms
200
ms
5 Vin
0-7
VDC
12 Vin
0-15
VDC
24 Vin
0-28
VDC
100
ms
Peak Input Voltage time
Isolation Specifications
Parameters
Nominal
Tested I/O voltage
3 sec
Typical
Rated
Units
1000 all models
VDC
Resistance
> 1000
MOhm
Capacitance
60
pF
Output Specifications
Parameters
Nominal
Typical
Maximum
Maximum
±3
Short Circuit protection
Units
%
Momentary (1 sec)
Line voltage regulation (Single)
For 1% change of Vin
±1.2
%
Line voltage regulation (Dual)
For 1% change of Vin
±1.2
%
Load voltage regulation (Single)
Load 20 – 100%
±10
%
Load voltage regulation (Single) 3.3V output model
Load 20 – 100%
±20
%
Load voltage regulation (Dual)
Load 20 – 100%
±10
%
Load voltage regulation (Dual) 3.3V output model
Load 20 – 100%
±20
%
±0.02
%/℃
100
mV p-p
50
ms
Temperature coefficient
Ripple & Noise
At 20MHz Bandwidth
Rising time
General Specifications
Parameters
Conditions
Typical
Switching frequency
100% load
80
Operating temperature
Full Load without Derating
Storage temperature
Maximum
KHz
-40 to+85
℃
-55 to +125
℃
Max Case temperature
Cooling
Weight
Dimensions (L x W x H)
MTBF
90
℃
90
%
Free air convection
Humidity
Case material
Units
Non-conductive black plastic
1.8
g
0.50 x 0.40 x 0.27 inches
12.70 x 10.16 x 6.85 mm
>1 191 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25℃)
NOTE: All specifications in this data sheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output
load unless otherwise specified
Safety Specifications
Parameters
Agency approvals
CE
EN55022 (Radiated Emissions) class B
Standards
EN55024 (Noise Immunity), IEC61000-4-2(ESD)
IEC61000-4-3(Radiated immunity)
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
B-XMD-1W&D-XMD-1W Series
TUBE OUTLINE DIMENSIONS
Dimensions
Unit :mm[inch]
Note:
Unit:mm[inch]
General tolerances: ±0.50mm[±0.020inch]
Pin section tolerances:±0.10mm[±0.004inch]
L=530mm[20.866inch]Devices per tube: 40pcs
General tolerances:±0.25mm[±0.010inch]
L=220mm[8.661inch] Devices per tube: 16pcs
RECOMMENDED FOOTPRINT
MECHANICAL DIMENSIONS
PIN CONNECTIONS
Note: grid 2.54*2.54mm
PIN
B-XMD-1W
D-XMD-1W
1
4
5
6
7
8
- V Input
+ V Input
+ V Output
No pin
- V Output
No pin
- V Input
+ V Input
+ V1 Output
- V1 Output
+ V2 Output
- V2 Output
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
REACH COMPLIANT INFORMATION
E-mail:[email protected]
Website:http://www.microdc.cn
http://www.microdc.cn
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3