DC-DC Converter DIP-Package DAN-1 SERIES, 1WATT, 3KVDC, ISOLATED, REGULATED FEATURES: 1500Vdc isolation voltage Single output models Low ripple & noise Operating temperature range -40 3 year warranty Model DAN1-0511 DAN1-0512 DAN1-0513 DAN1-0514 DAN1-0515 DAN1-1211 DAN1-1212 DAN1-1213 DAN1-1214 DAN1-1215 DAN1-1511 DAN1-1512 DAN1-1513 DAN1-1514 DAN1-1515 DAN1-2411 DAN1-2412 DAN1-2413 DAN1-2414 DAN1-2415 Input voltage (Vdc) ℃ to +85 ℃ Output voltage (Vdc) 5(4.75~5.25) 12(11.4~12.6) 15(13.5~16.5) 24(22.8~25.2) Output current (mA) Efficiency Typ. Min. Max. 5 20 200 71% 9 11.1 111 60% 12 8.3 83 64% 15 6.7 67 65% 24 4.2 42 62% 5 20 200 72% 9 11.1 111 67% 12 8.3 83 65% 15 6.7 67 64% 24 4.2 42 66% 5 20 200 70% 9 11.1 111 65% 12 8.3 83 65% 15 6.7 67 66% 24 4.2 42 66% 5 20 200 65% 9 11.1 111 63% 12 8.3 83 63% 15 6.7 67 63% 24 4.2 42 65% Notes: Other input and output models may available on request. ELECTRICAL ±3% max Output voltage accuracy --- Line regulation --- Load regulation 10% ~ 100% full load ±0.25% max. ±1% max. Isolation voltage Leakage current < 1mA/1min. 1500Vdc min. Isolation resistance Test at 500VDC 1000m Switching frequency --- Ripple & noise Bend width 20MHz www.pairuigroup.com Ω min. 100KHz typ. Page: 1/3 60mVp-p max. Date: 07/20/2015 * Subject to change without prior notice DC-DC Converter DIP-Package DAN-1 SERIES, 1WATT, 3KVDC, ISOLATED, REGULATED ELECTRICAL Temperature coefficient Rated load Operating temperature range --- Storage temperature range --- ±0.03%/℃ -40℃ to +85℃ -55℃ to +125℃ Short circuit protection --- 1S MTBF --- 3500KHrs Weight --- 2.5g Notes: All the parameters are measured at 25℃ ambient temperature, humidity < 75%, nominal input voltage, full load and after warm-up, unless otherwise specified. MECHANICAL CONNECTION PIN # SINGLE 1 GND 7 NC 8 No Pin 9 +Vo 10 No Pin 11 0V 14 +Vin Note: * Unit is mm(inch). ELECTRICAL CURVE www.pairuigroup.com Page: 2/3 Date: 07/20/2015 * Subject to change without prior notice DC-DC Converter DIP-Package DAN-1 SERIES, 1WATT, 3KVDC, ISOLATED, REGULATED NOTE RECOMMENDED TEST AND APPLICATION CIRCUIT CAPACITOR SELECTION INPUT VOLTAGE C1 OUTPUT VOLTAGE C2 5VDC 4.7μF 5VDC 4.7μF 12VDC 2.2μF 9VDC 2.2μF 15VDC 1.0μF 12VDC 1.0μF 24VDC 0.47μF 15VDC/24VDC 0.47μF www.pairuigroup.com Page: 3/3 Date: 07/20/2015 * Subject to change without prior notice