Pl tronics,. Inc.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
TC4 TCXO Series
Surface Mount or Full Size Metal Thru-Hole Temperature Compensated Xtal Oscillator
HCMOS, Clipped Sine Wave or Sine Wave Compatible
10.00 MHz – 60.00 MHz
Standard Specifications
Operating Temperature Range
vs. Temp
Overall Frequency
vs. Vcc / Load
Stability
Aging
Frequency Adj by Trimmer
Supply Voltage (Vcc)
Output Logic
Output Voltage Levels
Supply Current (Icc)
Output Load (see Test Circuit 1)
0 to +50°C to -40 to +85°C available
± 1.0 to ± 10 PPM over Operating Temperature Range available
± 0.5 PPM maximum over Vcc ± 5% / ± 0.3 PPM maximum over Load ± 5%
± 3 PPM first year, ± 1 PPM per year thereafter at 25°C ± 5%
± 3 PPM minimum
5.0 volts and 3.3 volts available
HCMOS
Clipped Sine Wave
Sine Wave
Logic “1” 90% of Vcc min
1 volt p-p minimum
Logic “0” 10% of Vcc max
Consult Factory
20 to 40 mA max
2 to 5 mA max
10 TTL Loads or 15pF
10 K // 10 pF
On Test Circuit for Clipped Sine Wave only: Add a 20 K resistor from output to ground
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
3TC4 6 H 100 A - 10.0M - XXX (Internal Code or blank)
Model / Supply Voltage
TC4= 5.0 volts ±5%
3TC4= 3.3 volts ±5%
Packaging
Tube or
on Pads,
SMD: bulk
Frequency in MHz
Operating Temperature Range {Tightest FS available}
A: 0 to +50°C {±1.0 PPM }
D: -20 to +75°C {± 2.0 PPM }
B: 0 to +70°C {±1.5 PPM }
E: -30 to +75°C {± 2.5 PPM }
C: -10 to +70°C {± 2.0 PPM } F: -40 to +85°C {± 5.0 PPM }
TCXO Package, Max Height
6=Thru-Hole, 5.0mm
7=Surface Mount, 5.5mm
8=Surface Mount, 4.0mm
9=Thru-Hole, 8.5mm
Frequency Stability (FS)
010: ± 1.0 PPM 030: ± 3.0 PPM
015: ± 1.5 PPM 050: ± 5.0 PPM
020: ± 2.0 PPM 100: ± 10.0 PPM
025: ± 2.5 PPM
Logic
C: Clipped Sine Wave
H: HCMOS
S: Sine Wave
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Mechanical: inches (mm)
not to scale
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
.600 (15.24)
Vcc
14
OUT
8
Vcc
N.C.
GND
OUT
.740 (18.8) MAX
.858 (21.8) MAX
.17
(4.3)
.12 (3.0)
Timmer hole locations may vary
7
GND
GND
GND
1
Vcc
2
OUT
GND
4
GND
3
.360 (9.14)
.100
(2.54)
TYP
.055
(1.4)
.66 (16.76)
.157 (4.0)
MIN
.04 x .20
(1.0 x 5.08)
.110 (2.8)
.799 (20.3)
OUT
8
1
N.C.
.600 (15.24)
Vcc
14
.600 (15.24)
.335 (8.5)
MAX
.457 (11.6)
.386 (9.8)
.300 (7.62)
7
GND
.300 (7.62)
.492 (12.5) MAX
.748 (19.0) MAX
.157 (4.0)
MAX
.217 (5.5)
MAX
.461 (11.7) MAX
.300 (7.62)
.193 (4.9)
MIN
Tab
.04 x .10
(1.0 x 2.5)
Package 9
Package 8
Package 7
.197 (5.0)
MAX
.457 (11.6)
Package 6
.600 (15.24)
.799 (20.3)
Jan 2003
Pl tronics, Inc. (425) 776 -1880, Fax: (425) 776-2760, [email protected], www.pletronics.com
26