PLETRONICS TCD4 TCD4 FEMTOCELL FEMTOCELL Series Series TCXO TCXO // TCVCXO TCVCXO Applications Features • Pletronics’ TCD4 Femtocell Series Temperature TCD4 Femto 3.2 x 5.0 x 1.50 mm LCC Ceramic Package • • • • • Compensated Crystal Oscillator Optional Voltage Control Function Low Power / Fast Warm Up Clipped Sine Wave Output SONET / SDH / DWDM Test & Measurement Telecom Transmission & Switching Equipment Base Stations / Picocell Wireless Communication Equipment 2.8V to 3.3V nominal Supply Voltage See table for developed Frequencies Electrical Characteristics Min Typ Max Unit Condition (Consult factory for other options) 8.192 - 40.0 MHz See table below for developed frequencies -200 -100 -50 - +200 +100 +50 ppb Over -40°C to +85°C Over -10°C to +70°C Over 0°C to +70°C - ±2.0 ppm Vcontrol 1.50 volts nominal if used when VCC > 3.0 volts Referenced to the value 25°C ± 2°C - +85 °C 2.8 - 3.3 Volts - 2.0 3.0 4.0 - mA 13 MHz 26 MHz 40 MHz Frequency Stability vs. Supply - - ±0.2 ppm Load: 10 Kohm || 10 pF, VCC ± 5% Frequency Stability vs. Load - - ±0.2 ppm Load: 10 Kohm || 10 pF, VCC ± 5% 0.5 - 2.5 Volts 1.50 volts nominal for VCC Frequency Pullability 2 0 ±8.0 ±12.0 ppm Positive Slope Linearity - - 2.0 % Parameter Frequency Range 2 Frequency Stability vs. Temperature 2 Frequency Initial Calibration Operating Temperature Range 2 Supply Voltage 1, 2 Supply Current 2 VCC ICC Vcontrol Range -40 Output Waveform Clipped Sine Wave at fixed VCC + load (reference to midpoint min/max frequency) See factory for other options Widest range available ± 5% Load: 10 Kohm || 10 pF, VCC ± 5% Dc Coupled Output Level 0.8 - - V p-p Startup Time - - 10.0 mS Within ± 2.0 ppm of final frequency Long Term Stability (Aging) - - ±1.0 ppm Per year at 25°C ± 2°C - -120 -134 -144 -145 - dBc/Hz 25°C ± 2°C at 26.0 MHz -55 - +95 °C Phase Noise 100 Hz 1 kHz 10 kHz 100 kHz Storage Temperature Range Note: 1 2 Load: 10 Kohm || 10 pF ± 10% Place a 10nF power supply bypass capacitor next to device for correct operation Typical capabilities shown. A unique datasheet is created for each specific device. See Factory for other options. The following is a list of developed frequencies. Consult factory for other options. 8.192M, 9.60M, 9.72M, 10.00M, 12.80M, 13.00M, 16.384M, 19.20M, 19.44M, 20.00M, 25.60M, 26.00M, 40.00M only Product information is current as of publication date. The product conforms to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. June 5, 2015 Rev. B Copyright © 2015, Pletronics Inc. C 19013 36th Ave. W, Lynnwood, WA 98036 USA C www.pletronics.com C 425-776-1880 Pg 1 PLETRONICS TCD4 TCD4 FEMTOCELL FEMTOCELL Series Series TCXO TCXO // TCVCXO TCVCXO Part Number (Possible Options shown) Series Model Operating Temperature VCC Supply Voltage 1 TCD4 Lowest Highest Frequency (ppm) (ppm) (MHz) -19.44M +40oC +45oC +50oC 10 - 40 MHz +60 C ± 1.0 0 +65oC ± 1.5 ± 2.0 ±5 ±8 o -20oC +70oC -25oC ± 2.5 +75oC +80oC -30oC -35oC Developed: 8.192M, 9.60M, 9.72M, 10.00M, 12.80M, 13.00M, 16.384M, 19.20M, 19.44M, 20.00M, 25.60M, 26.00M, 40.00M ± 0.5 +55oC -10oC -15oC 3.3 volts nominal 3.0 volts nominal 2.8 volts nominal +85oC -40oC 2 Pullability 1 A unique number will be assigned for your exact specification +10oC +5oC +0oC -5oC 1 Stability 1, 2 Contact Factory for non-standard specifications Not all stabilities are available with all operating temperature ranges. Contact Factory for exact combinations available. Device Marking FFFF = zzz = PLE = M U4 = YMD = YMD FFFF.zzz FFFF. zzz YMD C OR PLEzzzzz C PLE M U4 YMD YMD Crystal Frequency in MHz (See Note below) Internal factory codes Pletronics Internal factory codes Date code (may appear in one of 3 locations shown) Note: Output Frequency may be half the Crystal Frequency marking, depending on requirements. Specifications such as part number, frequency stability, supply voltage and operating temperature range, etc. are not identified from marking. External packaging labels and packing list will correctly identify the ordered Pletronics part number. Codes for Date Code YMD (Year Month Day) Code 4 5 6 7 8 Code A B C D E F G H J K L M Year 2014 2015 2016 2017 2018 Month JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC Code 1 2 3 4 5 6 7 8 9 A B C D E F G H J K L M N P R T U V W X Y Z 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Day Package Labeling Tape and Reel available for quantities of 250 to 1000 per reel, cut tape for < 250. 16mm tape, 8mm pitch. P/N Label is 1" x 2.6" (25.4mm x 66.7mm) Font is Courier New Bar code is 39-Full ASCII RoHs Label is 1" x 2.6" (25.4mm x 66.7mm) Font is Arial Pletronics Inc. certifies this device is in accordance with the RoHS 2 (2011/65/EU) and WEEE (2002/96/EC) directives. Pletronics Inc. guarantees the device does not contain the following: Cadmium, Hexavalent Chromium, Lead, Mercury, PBB’s, PBDE’s Weight of the Device: 0.10 grams Moisture Sensitivity Level: 1 As defined in J-STD-020D Second Level Interconnect code: e4 Product information is current as of publication date. The product conforms to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. June 5, 2015 Rev. B Copyright © 2015, Pletronics Inc. C 19013 36th Ave. W, Lynnwood, WA 98036 USA C www.pletronics.com C 425-776-1880 Pg 2 PLETRONICS TCD4 TCD4 FEMTOCELL FEMTOCELL Series Series TCXO TCXO // TCVCXO TCVCXO Mechanical Dimensions A Inches mm 0.197 ± 0.008 5.00 ± 0.20 B 0.126 ± 0.008 3.20 ± 0.20 C 0.059 max 1.50 max 1 0.055 1.40 1 0.031 0.80 1 0.043 1.10 1 0.102 2.60 1 0.020C 0.50C 1 0.008R 0.20R D E F G H J 1 Typical dimensions Pad Layout mm shown (Top View) Disclaimer: Recommended layout shown. Adjust pad layout as needed for individual process requirements. Solder mask required, as shown. (Not to Scale) Contacts (pads): Gold 11.8 to 39.4 µinches (0.3 to 1.0 µm) over Nickel 50 to 350 µinches (1.27 to 8.89 µm) Layout Pad Function Note 1 Vcontrol Input If this function is not specified, recommend connecting this pad to ground. EFC (Electronic Frequency Control). 2 Ground (GND) 3 Output The output is DC coupled. Most commonly used with external coupling capacitor. 0.001 to 0.01µF recommended. 4 VCC Supply Voltage Connect an appropriate 10nF power supply bypass capacitor as close as possible - N.C. All other pads on the bottom shall not be connected. These are internally connected for the TCXO compensation process All connection points in the designated region have solder mask cover to avoid any electrical connections (top view shown) For Optimum Jitter Performance, Pletronics recommends: $ $ $ $ $ A ground plane under the device Do not route large transient signals (both current and voltage) under the device Do not place near a large magnetic field such as a high frequency switching power supply Do not place near piezoelectric buzzers or mechanical fans Minimize air flow across the device Product information is current as of publication date. The product conforms to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. June 5, 2015 Rev. B Copyright © 2015, Pletronics Inc. C 19013 36th Ave. W, Lynnwood, WA 98036 USA C www.pletronics.com C 425-776-1880 Pg 3 PLETRONICS TCD4 TCD4 FEMTOCELL FEMTOCELL Series Series TCXO TCXO // TCVCXO TCVCXO Electrical Test /Load Circuit Environmental / ESD Ratings Reliability: Environmental Compliance Parameter ESD Rating Condition Model Min. Voltage Condition Mechanical Shock JESD22-B104 Human Body Model 2000V JESD22-A114 Vibration JESD22-B103 Charged Device Model 500V JESD 22-C101 Solderability IPC J-STD-002 Machine Model 200V JESD22-A115 Thermal Shock MIL-STD-883 Method 1011, Condition A Absolute Maximum Ratings Parameter Thermal Characteristics: The maximum die or junction temperature is 155oC The thermal resistance junction to board is 30 to 50oC/Watt depending on the solder pads, ground plane and construction of the PCB. Unit VCC Supply Voltage -0.6V to +6V Vi Input Voltage -0.6V to VCC + 0.6V Io Output Current -10mA to +10mA Product information is current as of publication date. The product conforms to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. June 5, 2015 Rev. B Copyright © 2015, Pletronics Inc. C 19013 36th Ave. W, Lynnwood, WA 98036 USA C www.pletronics.com C 425-776-1880 Pg 4 PLETRONICS TCD4 TCD4 FEMTOCELL FEMTOCELL Series Series TCXO TCXO // TCVCXO TCVCXO Reflow Cycle The part may be reflowed 2 times without degradation (typical for lead free processing). Tape and Reel Tape Constant Dimensions Table 1 Tape Size D1 min Do E1 Po P2 1.0 8mm 1.5 12mm +0.1 -0.0 16mm 24mm S1 min T max T1 max 0.6 0.6 0.1 2.0 1.5 1.75 4.0 ±0.05 1.5 ±0.1 ±0.1 2.0 ±0.1 1.5 Tape Variable Dimensions Table 2 Tape Size B1 max E2 min F P1 T2 max W max Ao, Bo & Ko 16mm 12.1 14.25 7.5 ±0.1 8.0 ±0.1 8.0 16.3 Note 1 Dimensions in mm Drawing Not to scale Note 1: Embossed cavity to conform to EIA– 481-B Reel Dimensions (may vary) Table 3 A B Reel Size Inches mm Inches mm 7 7.0 177.8 2.50 63.5 10 10.0 254.0 4.00 101.6 13 13.0 330.2 3.75 95.3 Product information is current as of publication date. The product conforms to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. C D mm mm 13.0 Tape size +0.4 +0.5 -0.2 +2.0 -0.0 June 5, 2015 Rev. B Copyright © 2015, Pletronics Inc. C 19013 36th Ave. W, Lynnwood, WA 98036 USA C www.pletronics.com C 425-776-1880 Pg 5 PLETRONICS TCD4 TCD4 FEMTOCELL FEMTOCELL Series Series TCXO TCXO // TCVCXO TCVCXO Important Notice Pletronics Incorporated (PLE) reserves the right to make corrections, improvements, modifications and other changes to this product at anytime. PLE reserves the right to discontinue any product or service without notice. Customers are responsible for obtaining the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to PLE’s terms and conditions of sale supplied at the time of order acknowledgment. PLE warrants performance of this product to the specifications applicable at the time of sale in accordance with PLE’s limited warranty. Testing and other quality control techniques are used to the extent PLE deems necessary to support this warranty. Except where mandated by specific contractual documents, testing of all parameters of each product is not necessarily performed. PLE assumes no liability for application assistance or customer product design. Customers are responsible for their products and applications using PLE components. To minimize the risks associated with the customer products and applications, customers should provide adequate design and operating safeguards. PLE products are not designed, intended, authorized or warranted to be suitable for use in life support applications, devices or systems or other critical applications that may involve potential risks of death, personal injury or severe property or environmental damage. Inclusion of PLE products in such applications is understood to be fully at the risk of the customer. Use of PLE products in such applications requires the written approval of an appropriate PLE officer. Questions concerning potential risk applications should be directed to PLE. PLE does not warrant or represent that any license, either express or implied, is granted under any PLE patent right, copyright, artwork or other intellectual property right relating to any combination, machine or process which PLE product or services are used. Information published by PLE regarding third-party products or services does not constitute a license from PLE to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from PLE under the patents or other intellectual property of PLE. Reproduction of information in PLE data sheets or web site is permissible only if the reproduction is without alteration and is accompanied by associated warranties, conditions, limitations and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. PLE is not responsible or liable for such altered documents. Resale of PLE products or services with statements different from or beyond the parameters stated by PLE for that product or service voids all express and implied warranties for the associated PLE product or service and is an unfair or deceptive business practice. PLE is not responsible for any such statements. Contacting Pletronics Inc. Pletronics, Inc. 19013 36th Ave. West Lynnwood, WA 98036-5761 U.S.A. Tel: 425.776.1880 Fax: 425.776.2760 email: [email protected] URL: www.pletronics.com Product information is current as of publication date. The product conforms to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. June 5, 2015 Rev. B Copyright © 2015, Pletronics Inc. C 19013 36th Ave. W, Lynnwood, WA 98036 USA C www.pletronics.com C 425-776-1880 Pg 6