MEDICAL PM60 Series 3 7 - 6 4 W AT T S - A C / D C S I N G L E & M U LT I P L E O U T P U T FEATURES • • • • • • • Medical and ITE approvals Compact size 2” x4” x1.18” Single, dual and triple outputs Wide-range input 90-264 VAC Low earth leakage current Level B emissions RoHS compliant SPECIFICATIONS INPUT OPERATING Voltage range 90-264 VAC Frequency Inrush current 47-63 Hz 30 A @ 115 VAC, or 60 A @ 230 VAC, at25°C cold start 1.3 A (rms) for 100 VAC 0.7 A (rms) for 240 VAC 150 µA max. @ 264 VAC, 63 Hz Input current Earth leakage current Isolation Input – Output: 4000VAC Input – Case:1500VAC Output – Case: 500VAC OUTPUT Efficiency Switching frequency 400,000 hours at full load at 25°C ambient, calculated per MIL-HDBK-217F 80-88% typical except PM60-31-3A and PM60-31-5 A at 75% typical 62 KHz tpical ENVIRONMENT Operating temperature: -10°C to +70°C Storage temperature: -40°C to +85°C Relative humidity: Derating: 5% to 95% non-condensing Derate from 100% to +50°C linearly to 50% at +70°C Output voltage See table Output current Ripple and noise Safety UL 60601-1, CSA C22.2 No. 601.1, TÜV EN 60601-1, UL 60950-1, CSA C22.2 No. 60950-1, TÜV EN 60950-1 Line regulation See table 100 mV peak to peak on 3.3 V & 5.0 V models, 1% peak to peak on other models ±0.5% maximum at full load C-Tick AS/NZS CISPR11 Group1, Class A Load regulation See table EMC standards Minimum load current See table Transient response Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500 us after a 25% step load change IEC60601-1-2, EN55011 / EN55022 and FCC, VCCI: Class B conducted . class B radiated Immunity standards Overvoltage protection Temperature coefficient Provided on output #1 only; set at 112–132% of its nominal output voltage All outputs protected to short circuit conditions All outputs ±0.04% /°C maximum EN61000-3-2, EN61000-3-3, EN61000-42, EN61000-4-3, EN61000-4-4, EN610004-5, EN61000-4-6, EN61000-4-8, EN61000-4-11 Hold-up time 12 ms minimum at 110 VAC Overcurrent protection 394 MTBF STANDARDS AND APPROVALS MECHANICAL Dimensions 101x50.8x30mm Weight 205g Doc. No. PBC9 Rev.C 28-4-11 PM60 Series SELECTION TABLE MODEL(1) OUTPUT #1 CLASS I PM60-10A PM60-12A PM60-13A PM60-14A PM60-18A PM60-23A PM60-25A PM60-31A PM60-31-3A PM60-31-5A PM60-32A PM60-39A OUTPUT #2 MAX. MIN. MAX. CURRENT V1 CURREN CURREN AT 5 CFM T T (2) 5V 12 V 15 V 24 V 48 V +5 V +5 V +5 V +3.3 V +5 V +5 V +5 V 0A 0A 0A 0A 0A 0.5 A 0.5 A 0.5 A 0.8 A 0.5 A 0.5 A 0.5 A 11.0 A 5.0 A 4.3 A 2.7 A 1.35 A 6.0 A 6.0 A 6.0 A 6.0 A 6.0 A 6.0 A 6.0 A (N/A) (N/A) (N/A) (N/A) (N/A) 8A 8A 8A 8A 8A 8A 8A TOL. ±2% ±2% ±2% ±2% ±2% ±3% ±3% ±3% ±3% ±3% ±3% ±3% V2 +12 V +24 V +12 V +5.2 V +3.3 V +15 V +24 V OUTPUT #3 MIN. MAX. CURREN CURREN T T (N/A) (N/A) (N/A) (N/A) (N/A) 0.1 A 3.0 A 0.1 A 1.5 A 0.1 A 3.0 A 0.1 A 3.0 A 0A 1.5 A 0.1 A 2.4 A 0.1 A 1.5 A TOL. V3 MIN. MAX. CURREN CURREN T T ±5% ±5% (N/A) ±5% -12 V ±5% +12 V ±5% +12 V ±5% -15 V ±5% -12 V TOL. MAX. OUTPUT POWER ±5% ±4% ±4% ±4% ±4% 55 W 60 W 64 W 64 W 64 W 55 W 55 W 55 W 37.5 W 37.5 W/47.5 W 55 W 55 W (N/A) (N/A) (N/A) (N/A) (N/A) (N/A 0A 0A 0A 0A 0A 0.5 A 0.3 A 0.3 A 0.5 A 0.5 A MEDICAL 3 7 - 6 4 W AT T S - A C / D C S I N G L E & M U LT I P L E O U T P U T NOTES: 1. Safety approvals are for PCB form only. To order unit with cover fitted, change suffix “A” to “C”. 2. Maximum current of output #1 of multi-output models can be 8 A at 5 CFM forced air provided by user. 3. 47.5 W with 5 CFM forced air provided by user 4. The output voltages of a multiple output model may go outside of the stated tolerance when an output load current is out of stated limits. All models may be operated at no-load without damage. 5. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10 µF tantalum capacitor in parallel with a 0.1 µF ceramic capacitor across the output. MECHANICAL SPECIFICATIONS OUTPUT POWER DERATING CURVE NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Connector CN1: Molex header 09-65-2038 or equivalent, mating with Molex housing 09-50-1031 or equivalent. 4. Connector CN2: Molex header 09-65-2068 or equivalent, mating with Molex housing 09-50-1061 or equivalent. 5. Ground tab is 0.25 [6.35] x 0.032 [0.8] fast-on connector. 6. To ensure compliance with level B emissions, connect the two “＊“ marked mounting holes with metallic standoffs to chassis. 7. Weight: 205 grams (0.45 lbs.) approx. PIN CHART MODEL PIN PM60-10A PM60-14A PM60-23A PM60-12A PM60-18A PM60-25A PM60-13A PM60-31A PM60-32A PM60-39A PM60-31-3A PM60-31-5A Doc. No. PBC9 Rev.C 28-4-11 1 2 3 4 5 6 +V1 +V1 V1 Return V1 Return N.C. N.C. V1 V1 Common Return N.C V2 V1 V1 Common Return V3 V2 V1 V1 Common Return V3 V2 Powering Progress – www.powerbox.com.au 395