ds-7k-12-xxxx l-t69frgbct-sa a0 - Para Light Electronics Co. Ltd.

PARA LIGHT ELECTRONICS CO., LTD.
4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan
Tel: 886-2-2225-3733
Fax: 886-2-2225-4800
http://www.para.com.tw
E-mail: [email protected]
DATA
SHEET
PART NO.: L-T69FRGBCT-SA
REV: A/0
CUSTOMER’S APPROVAL : _______________
DCC : ____________
DRAWING NO. : DS-7K-12-XXXX
DATE : 2012-11-9
PAGE
1 of 15
PARA-FOR-065
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Features
Û
Û
Û
Û
Û
Û
l
Top view PLCC6, Wide view angle, lighting color Red & Green & Blue.
EIA STD package, packing in 12mm tape on 7" diameter reels (ANSI/EIA-481-B-2001).
Compatible with automatic Pick & Place equipment.
Compatible with IR Reflow soldering and TTW soldering.
Pb free product and acceptable lead-free process!
Meet RoHS Green Product.
Application
Û
Û
Û
Backlighting (Switches, keys, displays, illuminated advertising)
Emergency lighting / Signal and symbol luminaries.
Decorative lighting.
l Package Outline Dimensions
3
6
2
1
5
4
Cathode Mark
3
G
6
2
1
R
5
B
4
Notes:
1. All dimensions are in millimeters.
2. Tolerance is ± 0.10mm (.004") unless otherwise noted.
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
2 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Absolute Maximum Ratings(Ta=25℃)
Parameter
Symbol
Rating
Unit
20
mA
100
mA
R
Continuous Forward Current
If
G
B
R
Pulse Forward Current*
Ifp
G
B
Power Consumption
Pc
Electrostatic Discharge
ESD
R
55
G
75
B
75
R
2000
G
1000
B
1000
mW
V
Operating Temperature Range
Topr
-40~+85
℃
Storage Temperature Range
Tstg
-40~+100
℃
Reverse Voltage
Vr
5
V
Soldering Temperature
Tsld
Reflow Soldering: 240℃/10sec
Hand Soldering:350℃/3sec
l Electro-Optical Characteristics (Ta=25℃)
Item
Symbol
Conditio
Min
R
Forward Voltage
Vf
G
If=20mA
B
R
Dominant Wavelength
λD
G
If=20mA
B
Viewing Angle 2θ 1/2
Δθ
Luminous Intensity
Iv
G
B
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
If=20mA
Max
2.4
Unit
3.0
3.6
v
3.0
3.6
619
629
520
530
465
475
If=20mA
R
Typ
2.0
120
350
480
800
1200
190
280
DATE : 2012-11-9
nm
deg
mcd
PAGE
3 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
Notes:
1. Luminous intensity is measured with a light sensor and filter combination that
proximities the CIE eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous
intensity.
3. Caution in ESD :
Static Electricity and surge damages the LED. It is recommended use a wrist band or
anti-electrostatic glove when handling the LED. All devices, equipment and machinery
must be properly grounded.
4. Major standard testing equipment by “Instrument System” Model : CAS140B Compact
Array Spectrometer and “KEITHLEY” Source Meter Model : 2400.
l Typical Electro-Optical Characteristics Curves
1.0
Intensity (%)
0.8
0.6
0.4
0.2
0.0
400 420 440 460 480 500 520 540 560 580 600 620 640 660 680 700
Wavelength (nm)
Relative Intensity VS Wavelength
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
4of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Typical Electro-Optical Characteristics Curves
(25℃ Ambient Temperature Unless Otherwise Noted)
1200
Luminous lntensity(mcd)
Forward Current(mA)
50
40
30
20
10
0
1.5
2.0
2.5
3.0
Fig.1 Forward Current vs.Forward Voltage
600
400
0
10
20
30
40
50
Forward Current(mA)
Fig.2 Luminous Intensity vs.Forward Current
1000
2.0
1.5
1.0
0.5
0
10
20
30
40
50
Relative luminous intensity(%)
2.5
Relative Luminous lntensity
Normalized @ 20mA
800
200
3.5
Forward Voltage(v)
1000
100
10
1
-60 -40 -20 0 20 40 60 80 100
Ambient Temperature Ta(℃ )
Forward Current(mA)
Fig.3 Relative Luminous Intensity vs.Forward Current
Fig.4 Luminous Intensity vs.Ambient Temperature
0°
10°
20°
50
Forward Current IF(mA)
30°
40
30
20
10
1.0
40°
0.9
50°
0.8
60°
70°
80°
90°
0.7
0
20
40
60
80
100
0.5
0.3
0.1 0.2
0.4
0.6
Ambient Temperature Ta(℃ )
Fig.5 Forward Current Derating Curve
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
Fig.6 Relative Intensity vs.Angle
DATE : 2012-11-9
PAGE
5of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Bin Code List
Luminous Intensity(IV), Unit:[email protected]
COLOR
R
G
B
Bin Code
Min
Max
430
4
1.9
2.0
430
530
5
2.0
2.1
530
650
6
2.1
2.2
7
2.2
2.3
Bin Code
Min
Max
P17
350
P18
P19
P20
Forward Voltage(VF), Unit:[email protected]
650
COLOR
R
800
P21
800
1000
8
2.3
2.4
P22
1000
1250
9
2.4
2.5
P23
1250
1550
13
2.8
2.9
P14
190
230
14
2.9
3.0
P15
230
280
15
3.0
3.1
P16
280
350
16
3.1
3.2
17
3.2
3.3
18
3.3
3.4
19
3.4
3.5
20
3.5
3.6
G(B)
Tolerance of each bin are±10%
Tolerance of each bin are±0.1Vol
Dominant Wavelength (Hue),Unit: [email protected]
COLOR
R
G
B
Bin Code
Min
Max
OC1
619
624
OC2
624
629
AP
520
525
AQ
525
530
AC
465
470
AD
470
475
Tolerance of each bin are±1nm
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
6 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Label Explanation
CUS. PART NO: To be denominated.
CUSTOMER: To be denominated.
PART NO: Refer to P16
IV--- Luminous Intensity Code
WD--- Dominant Wavelength
LOT NO:
E L P 1 1 0001
A
B C D
E
F
A---E: For series number
B---L: Local F: Foreign
C---P: PLCC SMD
D---Year
E---Month
F---SPEC.
PACKING QUANTITY OF BAG :
2000pcs max for T670 series
2000pcs max for T650 series
2000pcs max for S020 series
1000pcs max for T690 series
DATE CODE:2011 01
G H
G--- Year
H--- Month
I --- Day
08
I
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
7 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Reel Dimensions
Notes:
1.
2.
Taping Quantity : 1000pcs/reel、500pcs/reel
The tolerances unless noted is±0.1mm, Angle±0.5°, Unit: mm.
l Suggest Soldering Pad Dimensions
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
8 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l Package Dimensions Of Tape And Reel
Notes: All dimensions are in millimeters.
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
9of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
Moisture Resistant Packaging
Label
H: \SM D \SM D \SM D° ü × ° \± ê ? ? .j pg
H:\ SM D \SM D \SM D ° ü × ° \± ê ? ? .jp g
H:\S
M D\SM
D \SM
×
D° ü
ê
° \±
.jpg
??
l
REV: A/0
Reel
Label
Desiccant
Aluminum moistue-proof bag
2 40
M
S M D \S
H :\
D\S M
D°
?
\± ê ?
ü× °
.jp g
145
21 0
25
5
Label
Box
435
Carton
Notes : One reel in a bag, one bag in a inner box, ten inner boxes in a carton. Unit : mm.
l
Cleaning
Û If cleaning is required , use the following solutions for less than 1 minute and less than 40℃.
Û Appropriate chemicals: isopropyl alcohol. (When using other solvents, it should be confirmed
beforehand whether the solvents will dissolve the package and the resin or not.)
Û Effect of ultrasonic cleaning on the LED resin body differs depending on such factors as
ultrasonic power and the assembled condition. Before cleaning, a pre-test should be
confirm whether any damage to the LEDS will occur.
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
10of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
●
REV: A/0
Suggest Sn/Pb IR Reflow Soldering Profile Condition:
● Suggest
Pb-Free IR Reflow Soldering Profile Condition:
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
11 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
l CAUTIONS
1. Static Electricity:
* Static electricity or surge voltage damages the LEDs.
It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.
* All devices, equipment and machinery must be properly grounded.
It is recommended that measures be taken against surge voltage to the equipment that mounts the LEDs.
* When inspecting the final products in which LEDs were assembled, it is recommended to check
whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged
LEDs by a light-on test or a VF test at a lower current (blew 1mA is recommended).
* Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases,
the forward voltage becomes lower, or the LEDs do not light at the low current.
Criteria: (VF>2.0V,at IF=0.5m A )
2. Storage :
* Before opening the package :
The LEDs should be kept at 30°C or less and 85%RH or less. When storing the LEDs, moisture
proof packaging with absorbent material (silica gel) is recommended.
* After opening the package :
The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within
168 hours (7 days) after opening the package. If unused LEDs remain, they should be stored in
moisture proof packages, such as sealed containers with packages of moisture absorbent material
(silica gel). It is also recommended to return the LEDs to the original moisture poof bag and to
reseal the moisture proof bag again.
If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should e performed using the following conditions.
Baking treatment: more than 24hours at 65±5℃.
* Please avoid rapid transitions in ambient temperature in high humidity environments where
condensation may occur.
3. Soldering:
Do not apply any stress to the LED lens during soldering while the LED is at high temperature.
Recommended soldering condition.
* Reflow Soldering :
Pre-heat 120~150°C, 120sec. MAX., Peak temperature : 240°C Max. Soldering time : 10 sec Max.
* Soldering Iron : (Not recommended)
Temperature350°C Max., Soldering time : 3 sec. Max.(one time only), power dissipation of iron :
20W Max. use SN60 solder of solder with silver content and don’t to touch LED lens when soldering.
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
12 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
4. Lead-Free Soldering
For Reflow Soldering :
1、Pre-Heat Temp: 150-200℃,120sec.Max.
2、Soldering Temp: Temperature Of Soldering Pot Over 240℃,30sec.Max.
3、Peak Temperature: 260℃,10sec.
4、Reflow Repetition: 2 Times Max.
5、Suggest Solder Paste Formula : 93.3 Sn/3.1 Ag/3.1 Bi/0.5 Cu
For Soldering Iron (Not Recommended) :
1、Iron Tip Temp: 350℃ Max.
2、Soldering Iron: 30w Max.
3、Soldering Time: 3 Sec. Max. One Time.
5. Drive Method
Circuit model A
Circuit model B
(A)Recommended circuit.
(B)The difference of brightness between LED`s could be found due to the Vf-If characteristics of LED.
6. Reliability
1、Criteria For Judging The Damage
Item
Symbol
Test Conditions
Forward Voltage
VF
Reverse Current
Luminous Intensity
Criteria for Judgement
MIN.
Max.
IF=20mA
-
U.S.L.*)×1.1
IR
VR=5V
-
U.S.L.*)×2.0
IV
IF=20mA
L.S.L**)×0.7
-
*) U.S.L.: Upper Standard Level
**) L.S.L: Lower Standard Level
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
13 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
REV: A/0
2、Test Items And Results
Test Item
Reference
Standard
Resistance to Soldering Heat
JEITA
(Reflow Soldering)
ED-4701300 301
Solder ability (Reflow Soldering)
Thermal Shock
Temperature Cycle
High Temperature Storage
Temperature Humidity Storage
Low Temperature Storage
JEITA
ED-4701300 303
JEITA
ED-4701300 307
JEITA
ED-4701100 105
JEITA
ED-4701200201
JEITA
ED-4701100 103
JEITA
ED-4701200 202
Steady State Operating Life
Condition
Steady State Operating Life
of High Humidity Heat
Test Condition
Note
Tsld=260℃,10sec.
(Pre treatment
2times
30℃,70%,168hrs)
Tsld=215℃,3sec.
1time
(Lead Solder)
over 95%
-40℃ ~ 100℃
100cycles
30min. 30min.
-40℃ ~ 25℃~100℃~25℃
100cycles
30min. 5min. 30min. 5min
Number
of
Damaged
0/50
0/50
0/50
0/50
Ta=100℃
1000hrs.
0/50
Ta=60℃,RH=90%
1000hrs.
0/50
Ta=-40℃
1000hrs.
0/50
Ta=25℃,IF=20mA
1000hrs.
0/50
Ta=60℃,RH=90%,IF=15mA
500hrs.
0/50
7.Others:
The appearance and specifications of the product may be modified for improvement without notice.
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
DATE : 2012-11-9
PAGE
14 of 15
SURFACE MOUNT DEVICE LED
Part No. : L-T69FRGBCT-SA
l PART NO. SYSTEM :
L–
T 69
F RGB C T
Z-XXXX
REV: A/0
XXXX : Special Code
(Such as CCT、Luminous or others)
Z: With zener
(It not be showed if with no zener )
T : Taping for 7 inch reel
Lens color
C : Water Clear
W : White Diffused
D : Color Diffused
KY : 9mil AlInGap 590nm Super Yellow
KR : 9mil AlInGap 630 nm Super Red
TE(HE) : 14mil AlInGap 624 nm Super Red
TY(HY): 14mil AlInGap590 nm Super Yellow
LB : InGaN ITO rough 470nm Blue
LG(SG) : InGaN ITO rough520nm Green
W : InGaN + YAG White color
……
0 : Single chip
1/2 : Super thin single chip
5/6 : Dual chip
F : Three chip(Full color)
C : PCB Top View Type
T :PLCC Top View Type
S : Side View Type
DRAWING NO. : DS-7K-12-XXXX
PARA-FOR-068
65 :
3020 1.3T TYPE
67 :
3528 1.9T TYPE
020 : 3812 0.6T TYPE
68:
5630 0.9T TYPE
69:
5050 1.5T TYPE
DATE : 2012-11-9 PAGE
15of 15