NI 6070E/6071E Family Specifications

NI 6070E/6071E Family
Specifications
This document lists the I/O terminal summary and specifications for the devices that make up the NI 6070E/6071E family.
This family includes the following devices:
•
NI DAQPad-6070E
•
NI PCI-MIO-16E-1 (NI 6070E)
•
NI PXI-6070E
•
NI PCI-6071E
•
NI PXI-6071E
I/O Terminal Summary
Note With NI-DAQmx, National Instruments revised its terminal names so they are easier to understand and more
consistent among NI hardware and software products. The revised terminal names used in this document are usually
similar to the names they replace. For a complete list of Traditional NI-DAQ (Legacy) terminal names and their
NI-DAQmx equivalents, refer to Terminal Name Equivalents of the E Series Help.
Table 1. I/O Terminals
Terminal
Type and
Direction
Impedance
Input/
Output
AI <0..15>,
AI <16..63>†
AI
100 GΩ in
parallel
with 100 pF
AI SENSE,
AI SENSE 2†
AI
100 GΩ in
parallel
with 100 pF
AI GND
—
—
AO 0
AO
0.1 Ω
Short-circuit
to ground
5 at 10
AO 1
AO
0.1 Ω
Short-circuit
to ground
5 at 10
AO EXT REF
AI
10 kΩ
25/15
AO GND
—
Terminal Name
—
Source
(mA at V)
Sink
(mA at V)
Rise
Time
(ns)
Bias
25/15
—
—
—
±200 pA
25/15
—
—
—
±200 pA
—
—
—
—
5 at –10
20 V/µs
—
5 at –10
20 V/µs
—
Protection
(V) On/Off
—
—
—
—
—
—
—
—
—
—
Table 1. I/O Terminals (Continued)
Terminal
Type and
Direction
Impedance
Input/
Output
Protection
(V) On/Off
Source
(mA at V)
Sink
(mA at V)
Rise
Time
(ns)
Bias
D GND
—
—
—
—
—
—
—
+5 V
—
—
—
—
Terminal Name
0.1 Ω
Short-circuit
to ground
1A
VCC + 0.5
13 at
(VCC – 0.4)
24 at 0.4
1.1
50 kΩ pu
P0.<0..7>
DIO
—
AI HOLD COMP
DO
—
—
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
EXT STROBE*
DO
—
—
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
VCC +
0.5/±35
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
9 kΩ pu,
10 kΩ pd
PFI 0/
(AI START TRIG)
AI/DIO
10 kΩ
PFI 1/
(AI REF TRIG)
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 2/
(AI CONV CLK)*
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 3/
CTR 1 SOURCE
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 4/CTR 1 GATE
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
CTR 1 OUT
DO
—
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 5/
(AO SAMP CLK)*
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 6/
(AO START TRIG)
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 7/
(AI SAMP CLK)
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 8/
CTR 0 SOURCE
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
PFI 9/CTR 0 GATE
DIO
—
VCC + 0.5
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
CTR 0 OUT
DO
—
3.5 at
(VCC – 0.4)
5 at 0.4
1.5
50 kΩ pu
NI 6070E/6071E Family Specifications
—
—
2
ni.com
Table 1. I/O Terminals (Continued)
Terminal Name
Terminal
Type and
Direction
Impedance
Input/
Output
Protection
(V) On/Off
Source
(mA at V)
Sink
(mA at V)
DO
—
—
3.5 at
(VCC – 0.4)
5 at 0.4
FREQ OUT
Rise
Time
(ns)
1.5
Bias
50 kΩ pu
* Indicates active low.
†
NI PCI/PXI-6071E only.
AI = Analog Input
DIO = Digital Input/Output
AO = Analog Output
DO = Digital Output
AI/DIO = Analog Input/Digital Input/Output
pd = pull-down
pu = pull-up
Note: The tolerance on the 50 kΩ pull-up resistors is large. Actual value might range between 17 kΩ and 100 kΩ.
Specifications
The following specifications are typical at 25 °C unless otherwise noted.
Analog Input
Input Characteristics
Input signal ranges
Number of channels
NI 6070E .................................... 16 single-ended
or 8 differential
(software-selectable
per channel)
Range
(Software-Selectable)
NI 6071E .................................... 64 single-ended
or 32 differential
(software-selectable
per channel)
Type of A/D converter (ADC)........ Successive
approximation
Resolution ....................................... 12 bits, 1 in 4,096
Maximum sampling rate ................. 1.25 MS/s
Input Range
Bipolar
Unipolar
20 V
±10 V
—
10 V
±5 V
0 to 10 V
5V
±2.5 V
0 to 5 V
2V
±1 V
0 to 2 V
1V
±500 mV
0 to 1 V
500 mV
±250 mV
0 to 500 mV
200 mV
±100 mV
0 to 200 mV
100 mV
±50 mV
0 to 100 mV
Input coupling .................................DC
Maximum working voltage
(signal and common mode) .............Each input should remain
within ±11 V of ground
Overvoltage protection
Powered on .................................±25 V
Powered off.................................±15 V
Inputs protected
NI 6070E.....................................AI <0..15>, AI SENSE
NI 6071E.....................................AI <0..63>, AI SENSE,
AI SENSE 2
© National Instruments Corporation
3
NI 6070E/6071E Family Specifications
FIFO buffer size
NI DAQPad-6070E.....................2,048 samples (S)
NI PXI-6070E .............................512 S
NI PCI/PXI-6071E......................512 S
NI PCI-MIO-16E-1.....................512 S
DMA (PCI and PXI only)
Channels......................................3
Data sources/destinations............Analog input, analog
output, counter/timer 0,
or counter/timer 1
Data transfers
NI DAQPad-6070E.....................Interrupts,
programmed I/O
NI PXI-6070E .............................DMA, interrupts,
programmed I/O
NI PCI/PXI-6071E......................DMA, interrupts,
programmed I/O
NI PCI-MIO-16E-1.....................DMA, interrupts,
programmed I/O
DMA modes ....................................Scatter-gather
(single-transfer,
demand-transfer)
Configuration memory size .............512 words
(1 word = 8 bits)
NI 6070E/6071E Family Specifications
4
ni.com
© National Instruments Corporation
5
NI 6070E/6071E Family Specifications
0
0
0.2
0.1
0.0672
0.0672
0.0672
0.0672
0.0672
0.0672
0.0272
0.0672
0.0672
0.0672
0.0672
0.0672
0.0672
0.0272
0.0672
24 Hours
0.0714
0.0714
0.0714
0.0714
0.0714
0.0714
0.0314
0.0714
0.0714
0.0714
0.0714
0.0714
0.0714
0.0314
0.0714
1 Year
% of Reading
0.049
0.081
0.176
0.335
0.653
1.61
3.20
0.049
0.081
0.176
0.335
0.653
1.61
3.20
6.38
Offset
(mV)
0.071
0.098
0.208
0.305
0.610
1.53
3.05
0.071
0.098
0.208
0.305
0.610
1.53
3.05
6.10
Single Pt.
0.007
0.011
0.024
0.042
0.085
0.211
0.423
0.007
0.011
0.024
0.042
0.085
0.211
0.423
0.846
Averaged
Noise + Quantization (mV)
Absolute Accuracy
0.0010
0.0010
0.0010
0.0010
0.0010
0.0010
0.0005
0.0010
0.0010
0.0010
0.0010
0.0010
0.0010
0.0005
0.0010
Temp Drift
(%/°C)
0.127
0.235
0.558
1.092
2.167
5.391
6.765
0.091
0.163
0.379
0.735
1.452
3.605
5.193
14.369
Absolute
Accuracy
at Full
Scale (mV)
0.082
0.111
0.238
0.368
0.737
1.84
3.68
0.082
0.111
0.238
0.368
0.737
1.84
3.68
7.37
Single Pt.
0.009
0.015
0.032
0.056
0.111
0.278
0.557
0.009
0.015
0.032
0.056
0.111
0.278
0.557
1.11
Averaged
Relative Accuracy
Resolution (mV)
Note: Accuracies are valid for measurements following an internal E Series calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings.
Measurement accuracies are listed for operational temperatures within ±1 °C of internal calibration temperature and ±10 °C of external or factory-calibration temperature.
NI recommends a one-year calibration interval. The Absolute Accuracy at Full Scale calculations were performed for a maximum range input voltage (for example, 10 V for
the ±10 V range) after one year, assuming 100 points of averaged data. Go to ni.com/info and enter info code rdspec for example calculations.
0
0
1
0.5
0
–0.1
0.1
2
–0.25
0.25
0
–0.5
0.5
5
–1
1
0
–2.5
2.5
10
–5
5
–0.05
–10
10
0.05
Negative
Full Scale
Positive
Full Scale
Nominal Range (V)
Accuracy Information
Transfer Characteristics
Relative accuracy
Dithered ......................................±0.5 LSB typ
Undithered ..................................±1.5 LSB max
Differential nonlinearity (DNL) ......±0.5 LSB typ,
±1.0 LSB max
No missing codes.............................12 bits, guaranteed
Offset error
Pregain error after calibration .....±12 µV max
Pregain error before
calibration ...................................±2.5 mV max
Postgain error after calibration ...±0.5 mV max
Postgain error before
calibration ...................................±100 mV max
Gain error (relative to calibration reference)
After calibration (gain = 1) .........±0.02% of reading max
Before calibration .......................±2.5% of reading max
Gain ≠ 1 with gain error
adjusted to 0 at gain = 1 ..............±0.02% of reading max
Amplifier Characteristics
Input impedance
Normal powered on ....................100 GΩ in parallel
with 100 pF
Powered off.................................820 Ω min
Overload......................................820 Ω min
Input bias current.............................±200 pA
Input offset current ..........................±100 pA
Common-mode rejection ratio (CMRR), DC to 60 Hz
Range
CMRR
20 V
95 dB
10 V
100 dB
100 mV to 5 V
106 dB
Dynamic Characteristics
Bandwidth
Small signal (–3 dB) ...................1.6 MHz
Large signal (1% THD) ..............1 MHz
NI 6070E/6071E Family Specifications
6
ni.com
Settling time to full-scale step
Accuracy*
Device
NI 6070E
NI 6071E
Range
±0.012% (±0.5 LSB)
±0.024% (±1 LSB)
±0.098% (±4 LSB)
20 V
2 µS typ, 3 µS max
1.5 µS typ, 2 µS max
1.3 µS typ, 1.5 µS max
10 V
2 µS typ, 3 µS max
1.5 µS typ, 2 µS max
0.9 µS typ, 1 µS max
200 mV to 5 V
2 µS typ, 3 µS max
1.5 µS typ, 2 µS max
1 µS typ, 1.5 µS max
100 mV
2 µS typ, 3 µS max
1.5 µS typ, 2 µS max
1.9 µS typ, 2 µS max
20 V
3 µS typ, 5 µS max
1.9 µS typ, 2.5 µS max
1.2 µS typ, 1.5 µS max
10 V
3 µS typ, 5 µS max
1.9 µS typ, 2.5 µS max
1.2 µS typ, 1.3 µµS max
200 mV to 5 V
3 µS typ, 5 µS max
1.9 µS typ, 2.5 µS max
1.2 µS typ, 1.5 µS max
100 mV
3 µS typ, 5 µS max
1.9 µS typ, 2.5 µS max
1.3 µS typ, 1.5 µS max
*
Accuracy values are valid for source impedances <1 kΩ. Refer to Multichannel Scanning Considerations of the E Series
Help for more information.
Analog Output
System noise (LSBrms, not including quantization)
Range
Dither Off
Dither On
1 to 20 V
0.25
0.5
500 mV
0.4
0.6
200 mV
0.5
0.7
100 mV
0.8
0.9
Output Characteristics
Number of channels ........................2 voltage outputs
Resolution........................................12 bits, 1 in 4,096
Max update rate, waveform generation
FIFO Mode
Crosstalk (DC to 100 kHz)
Adjacent channels....................... –75 dB
All other channels....................... –90 dB
Non-FIFO Mode
Internally
Timed
Externally
Timed
1 MS/s
950 kS/s
1 Channel
2 Channels
800 kS/s,
system
dependent
400 kS/s,
system
dependent
Stability
Offset temperature coefficient
Type of D/A converter (DAC) ........Double-buffered,
multiplying
Pregain........................................ ±5 µV/°C
Postgain ...................................... ±240 µV/°C
FIFO buffer size ..............................2,048 S
Gain temperature coefficient........... ±20 ppm/°C
Data transfers...................................DMA, interrupts,
programmed I/O
DMA modes ....................................Scatter-gather
(single-transfer,
demand-transfer)
© National Instruments Corporation
7
NI 6070E/6071E Family Specifications
Accuracy Information
Nominal Range (V)
Positive
Full Scale
Negative
Full Scale
Absolute Accuracy
% of Reading
24 Hours
90 Days
1 Year
Offset
(mV)
Temp Drift
(%/°C)
Absolute
Accuracy
at Full
Scale (mV)
10
–10
0.0177
0.0197
0.0219
±5.93
0.0005
8.127
10
0
0.0177
0.0197
0.0219
±3.49
0.0005
5.685
Note: Accuracies are valid for measurements following an internal E Series calibration. Averaged numbers assume dithering
and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 °C
of internal calibration temperature and ±10 °C of external or factory-calibration temperature. NI recommends a one-year
calibration interval. The Absolute Accuracy at Full Scale calculations were performed for a maximum range input voltage
(for example, 10 V for the ±10 V range) after one year, assuming 100 points of averaged data. Go to ni.com/info and enter
info code rdspec for example calculations.
Transfer Characteristics
External reference input
Range.......................................... ±11 V
Relative accuracy, or integral nonlinearity (INL)
Overvoltage protection
After calibration ..........................±0.3 LSB typ,
±0.5 LSB max
Powered on ............................ ±25 V
Before calibration .......................±4 LSB max
Powered off............................ ±15 V
Input impedance ......................... 10 kΩ
DNL
Bandwidth (–3 dB) ..................... 1 MHz
After calibration ..........................±0.3 LSB typ,
±1.0 LSB max
Dynamic Characteristics
Before calibration .......................±3 LSB max
Settling time for full-scale step ....... 3 µs to ±0.5 LSB
accuracy
Monotonicity ...................................12 bits, guaranteed
after calibration
Slew rate ......................................... 20 V/µs
Offset error
Noise ............................................... 200 µVrms,
DC to 1 MHz
After calibration ..........................±1.0 mV max
Before calibration .......................±200 mV max
Glitch energy (at mid-scale transition)
Gain error
(relative to external reference) ........0 to 0.67% of output max,
not adjustable
Magnitude
Reglitching disabled .............. ±20 mV
Reglitching enabled ............... ±4 mV
Voltage Output
Duration...................................... 1.5 µs
Ranges .............................................±10 V, 0 to 10 V,
±AO EXT REF,
0 to AO EXT REF
(software-selectable)
Stability
Offset temperature coefficient ........ ±50 µV/°C
Gain temperature coefficient
Output coupling...............................DC
Internal reference........................ ±25 ppm/°C
Output impedance............................0.1 Ω max
External reference....................... ±25 ppm/°C
Current drive....................................±5 mA max
Protection.........................................Short-circuit to ground
Power-on state .................................0 V (± 200 mV)
NI 6070E/6071E Family Specifications
8
ni.com
Digital I/O
Min gate pulse duration...................10 ns, edge-detect mode
Number of channels ........................ 8 input/output
Data transfers...................................DMA, interrupts,
programmed I/O
Compatibility .................................. 5 V/TTL
DMA modes ....................................Scatter-gather
(single-transfer,
demand-transfer)
Digital logic levels on P0.<0..7>
Level
Min
Max
Input low voltage
0V
0.8 V
Triggers
Input high voltage
2.0 V
5.0 V
Analog Trigger
Input low current (Vin = 0 V)
—
–320 µA
Input high current (Vin = 5 V)
—
10 µA
Source..............................................All analog input channels,
external trigger
(PFI 0/AI START TRIG)
Output low voltage
(IOL = 24 mA)
—
0.4 V
Purpose
Output high voltage
(IOH = –13 mA)
4.35 V
Analog input ...............................Start, reference,
and pause trigger,
sample clock
—
Analog output .............................Start and pause trigger,
sample clock
Power-on state................................. Input (high-impedance)
Counter/timers ............................Source, gate
Data transfers .................................. Programmed I/O
Level
Transfer rate (1 word = 8 bits), maximum with NI-DAQ,
system-dependent
Internal ........................................±Full-scale
External.......................................±10 V
NI DAQPad-6070E .................... 5 kwords/s
Slope................................................Positive or negative
(software-selectable)
NI PXI-6070E............................. 50 kwords/s
NI PCI/PXI-6071E ..................... 50 kwords/s
Resolution........................................8 bits, 1 in 256
NI PCI-MIO-16E-1 .................... 50 kwords/s
Hysteresis ........................................Programmable
Constant sustainable rate ................ 1 to 10 kwords/s, typ
Bandwidth (–3 dB)
Timing I/O
Internal ........................................2 MHz
Number of channels ........................ 2 up/down
counter/timers,
1 frequency scaler
External.......................................7 MHz
External input (PFI 0/AI START TRIG)
Impedance...................................10 kΩ
Resolution
Counter/timers ............................ 24 bits
Coupling......................................DC
Frequency scaler......................... 4 bits
Protection
When configured as
a digital signal ........................–0.5 to VCC + 0.5 V
Compatibility .................................. 5 V/TTL
Base clocks available
Counter/timers ............................ 20 MHz, 100 kHz
When configured as an analog
trigger signal or disabled ........±35 V
Frequency scaler......................... 10 MHz, 100 kHz
Powered off ............................±35 V
Base clock accuracy........................ ±0.01%
Max source frequency..................... 20 MHz
Min source pulse duration............... 10 ns, edge-detect mode
© National Instruments Corporation
9
NI 6070E/6071E Family Specifications
Power
Digital Trigger
Purpose
Bus Requirement
Analog input ...............................Start, reference,
and pause trigger,
sample clock
PCI/PXI-6070E/6071E
+5 VDC (±5%) ............................... 1.1 A
DAQPad-6070E
9 to 25 VDC.................................... 17 W
Analog output .............................Start and pause trigger,
sample clock
Counter/timers ............................Source, gate
Note Excludes power consumed through +5 V
available at the I/O connector.
External sources ..............................PFI <0..9>, RTSI <0..6>
Compatibility...................................5 V TTL
I/O Connector Power
Response..........................................Rising or falling edge
Pulse width ......................................10 ns min
Power available at I/O connector.... +4.65 to +5.25 VDC
at 1 A
RTSI Trigger
Discharge time with BP–1
battery pack DAQPad-6070E ......... 2.5 h
PCI...................................................7
Physical
DAQPad ..........................................4
Dimensions (not including connectors)
NI DAQPad-6070E .................... 30.7 cm × 25.4 cm ×
4.3 cm
(12.1 in. × 10 in. × 1.7 in.)
PXI Trigger Bus (PXI Only)
Trigger lines ....................................6
Star trigger.......................................1
NI PXI-6070E/6071E ................. 16 cm × 10 cm
(6.3 in. × 3.9 in.)
Calibration
NI PCI-6071E,
NI PCI-MIO-16E-1 .................... 17.5 cm × 10.7 cm
(6.9 in. × 4.2 in.)
Recommended warm-up time
NI DAQPad-6070E.....................30 minutes
NI PXI-6070E .............................15 minutes
Weight
NI PCI/PXI-6071E......................15 minutes
NI DAQPad-6070E .................... 1955 g (4 lb 4.9 oz)
NI PCI-MIO-16E-1.....................15 minutes
NI PXI-6070E ............................ 203 g (7.1 oz)
Calibration interval..........................1 year
NI PCI-6071E/
NI PCI-MIO-16E-1 .................... 115 g (4.1 oz)
Onboard calibration reference
NI PXI-6071E ............................ 214 g (7.5 oz)
Level ...........................................5.000 V (±3.5 mV),
over full operating
temperature, actual value
stored in EEPROM
I/O connector
NI 6070E .................................... 68-pin male 0.050 D-type
NI 6071E .................................... 100-pin female 0.050
D-type
Temperature coefficient ..............±5 ppm/°C max
Long-term stability .....................±15 ppm/ 1,000 h
Maximum Working Voltage
Bus Interface
Maximum working voltage refers to the signal voltage plus
the common-mode voltage.
Type.................................................Master, slave
NI DAQPad-6070E
Channel-to-earth......................... 11 V,
Installation Category I
Channel-to-channel .................... 11 V,
Installation Category I
NI 6070E/6071E Family Specifications
10
ni.com
Electromagnetic Compatibility
NI PXI-6070E, NI PCI/PXI-6071E, NI PCI-MIO-16E-1
Channel-to-earth......................... 11 V,
Installation Category I
Emissions ........................................EN 55011 Class A at 10 m
FCC Part 15A above
1 GHz
Channel-to-channel .................... 11 V,
Installation Category I
Immunity .........................................EN 61326:1997
A2:2001, Table 1
Environmental
CE, C-Tick, and FCC Part 15 (Class A) Compliant
Operating temperature .................... 0 to 55 °C
Storage temperature ........................ –20 to 70 °C
Note For EMC compliance, operate this device
with shielded cabling.
Relative humidity............................ 10 to 90%,
noncondensing
CE Compliance
Maximum altitude........................... 2,000 m
This product meets the essential requirements of applicable
European Directives, as amended for CE marking, as follows:
Pollution Degree
(indoor use only) ............................. 2
Low-Voltage Directive (safety).......73/23/EEC
NI PCI-6071E OEM
Electromagnetic Compatibility
Directive (EMC)..............................89/336/EEC
Maximum ambient temperature...... 50 °C for use in Class 1,
Division 2 hazardous
locations
Note Refer to the Declaration of Conformity
(DoC) for this product for any additional regulatory
compliance information. To obtain the DoC for this
product, visit ni.com/certification, search
by model number or product line, and click the
appropriate link in the Certification column.
Safety
NI PCI-MIO-16E-1, PXI-6070E, PCI/PXI-6071E
These devices meet the requirements of the following
standards of safety for electrical equipment for measurement,
control, and laboratory use:
•
IEC 61010-1, EN 61010-1
•
UL 61010-1
•
CAN/CSA-C22.2 No. 61010-1
Note For UL and other safety certifications,
refer to the product label, or visit ni.com/
certification, search by model number or
product line, and click the appropriate link in the
Certification column.
NI DAQPad-6070E
The device meets the requirements of the following standards
for safety and electrical equipment for measurement, control,
and laboratory use:
•
IEC 60950-1, EN 60950-1
•
UL 60950-1
•
CAN/CSA-C22.2 No. 60950-1
Note For UL and other safety certifications,
refer to the product label, or visit ni.com/
certification, search by model number or
product line, and click the appropriate link in
the Certification column.
© National Instruments Corporation
11
NI 6070E/6071E Family Specifications
AI 8
34 68
AI 0
AI 1
33 67
AI GND
AI GND
32 66
AI 9
AI 10
31 65
AI 2
AI 3
30 64
AI GND
AI GND
29 63
AI 11
AI 4
28 62
AI SENSE
AI GND
27 61
AI 12
AI 13
26 60
AI 5
AI 6
25 59
AI GND
AI GND
24 58
AI 14
AI 15
23 57
AI 7
AO 0
22 56
AI GND
AO 1
21 55
AO GND
AO EXT REF
P0.4
20 54
19 53
AO GND
D GND
D GND
18 52
P0.0
P0.1
17 51
P0.5
P0.6
16 50
D GND
D GND
15 49
P0.2
+5 V
14 48
P0.7
D GND
13 47
P0.3
D GND
12 46
AI HOLD COMP
PFI 0/AI START TRIG
11 45
EXT STROBE
PFI 1/AI REF TRIG
10 44
D GND
D GND
9
43
PFI 2/AI CONV CLK
+5 V
8
42
PFI 3/CTR 1 SRC
D GND
7
41
PFI 4/CTR 1 GATE
PFI 5/AO SAMP CLK
6
40
CTR 1 OUT
PFI 6/AO START TRIG
5
39
D GND
D GND
4
38
PFI 7/AI SAMP CLK
PFI 9/CTR 0 GATE
3
37
PFI 8/CTR 0 SRC
CTR 0 OUT
2
36
D GND
FREQ OUT
1
35
D GND
Figure 1. NI PXI-6070E/PCI-MIO-16E-1 Pinout
NI 6070E/6071E Family Specifications
12
ni.com
PFI 9
PFI 8
PFI 7
PFI 6
PFI 5
PFI 4
PFI 3
PFI 2
PFI 1
D GND
USER 2
FREQ OUT
+5 V
+5 V
D GND
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
CTR 1 OUT
D GND
USER 1
AI HOLD COMP
EXT STROBE
AI SENSE
AI GND
Figure 2. NI DAQPad-6070E BNC Pinout
AI GND
1
51
AI 16
AI GND
2
52
AI 24
AI 0
3
53
AI 17
AI 8
4
54
AI 25
AI 1
5
55
AI 18
AI 9
6
56
AI 26
AI 2
7
57
AI 19
AI 10
8
58
AI 27
AI 3
9
59
AI 20
AI 11
10 60
AI 28
AI 4
11 61
AI 21
AI 12
12 62
AI 29
AI 5
13 63
AI 22
AI 13
14 64
AI 30
AI 6
15 65
AI 23
AI 14
16 66
AI 31
AI 7
17 67
AI 32
AI 15
18 68
AI 40
AI SENSE
19 69
AI 33
AO 0
20 70
AI 41
AO 1
21 71
AI 34
AO EXT REF
22 72
AI 42
AO GND
23 73
AI 35
D GND
24 74
AI 43
P0.0
25 75
AI SENSE 2
P0.4
26 76
AI GND
P0.1
27 77
AI 36
P0.5
28 78
AI 44
P0.2
29 79
AI 37
P0.6
30 80
AI 45
P0.3
31 81
AI 38
P0.7
32 82
AI 46
D GND
33 83
AI 39
+5 V
34 84
AI 47
+5 V
35 85
AI 48
AI HOLD COMP
36 86
AI 56
EXT STROBE
37 87
AI 49
PFI 0/AI START TRIG
38 88
AI 57
PFI 1/AI REF TRIG
39 89
AI 50
PFI 2/AI CONV CLK
40 90
AI 58
PFI 3/CTR 1 SRC
41 91
AI 51
PFI 4/CTR 1 GATE
42 92
AI 59
CTR 1 OUT
43 93
AI 52
PFI 5/AO SAMP CLK
44 94
AI 60
PFI 6/AO START TRIG
45 95
AI 53
PFI 7/AI SAMP CLK
46 96
AI 61
PFI 8/CTR 0 SRC
47 97
AI 54
PFI 9/CTR 0 GATE
48 98
AI 62
CTR 0 OUT
49 99
AI 55
FREQ OUT
50 100
AI 63
Figure 3. NI 6071E Pinout
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.
Refer to the Terms of Use section on ni.com/legal for more information about National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade
names of their respective companies. For patents covering National Instruments products, refer to the
appropriate location: Help»Patents in your software, the patents.txt file on your CD, or
ni.com/patents.
© 2003–2005 National Instruments Corporation. All rights reserved.
370725C-01
Dec05