KP Series BI-POLARIZED, WIDE TEMPERATURE 雙極性寬溫品 Bi-polarized with wide temperature range -55°C ~ +105°C 雙極性和適用於 -55°C ~+105°C 的寬溫範圍 Load life of 1000 hours 負荷壽命 1000 小時 Comply with the RoHS directive 符合 RoHS 指令 CN KP Wide Temp. 寬溫化 SPECIFICATIONS 特性表 Items 項目 Characteristics Voltage Range 6.3 ~ 50V 額定工作電壓範圍 Capacitance Range 主要特性 -55 ~ +105°C Operation Temperature Range 使用温度範圍 0.1 ~ 47μF 靜電容量範圍 Capacitance Tolerance 靜電容量允許偏差 ±20% at 120Hz, 20°C Leakage Current 漏電流 Leakage current≦0.005CV or 10μA, whichever is greater (after 2 minutes application of rated voltage) 漏電流≦0.005CV 或 10μA，取較大值（施加額定工作電壓 2 分鐘後） Measurement frequency 測試頻率: 120Hz, Temperature 温度: 20°C Dissipation Factor (tan δ) 損耗角正切 Rated Voltage (V) 額定工作電壓 tan δ (max.) 最大損耗角正切 6.3 0.24 10 0.20 16, 25 0.17 35, 50 0.15 Measurement frequency 測試頻率: 120Hz Rated Voltage (V) 額定工作電壓 Impedance Ratio 阻抗比 Z(-25°C) / Z(20°C) Z(-55°C) / Z(20°C) ZT/Z20 (max.) Stability at Low Temperature 低溫特性 6.3 4 8 10 3 6 16, 25 2 4 35, 50 2 3 After 1000 hours application of the rated voltage at 105°C (the polarity needs to exchange every 250 hours), they meet the characteristics listed below. 在 105°C 環境中施加額定工作電壓 1000 小時（每 250 小時必須轉換一次極性）後，電容器的特性符合下表的要求。 Load Life 高溫負荷特性 Capacitance Change 靜電容量變化率 Dissipation Factor 損耗角正切 Leakage Current 漏電流 Within ±20% of initial value 初始值的±20%以內 200% or less of initial specified value 不大於規範值的 200% initial specified value or less 不大於規範值 After leaving capacitors under no load at 105°C for 1000 hours, they meet the specified value for load life characteristics listed above. 在 105°C 環境中無負荷放置 1000 小時後，電容器的特性符合高溫負荷特性中所列的規定值。 Shelf Life 高溫貯存特性 After reflow soldering and restored at room temperature, they meet the characteristics listed below. 經過回流焊並冷卻至室溫後，電容器的特性符合下表的要求。 Resistance to Soldering Heat 耐焊接熱特性 Capacitance Change 靜電容量變化率 Dissipation Factor 損耗角正切 Leakage Current 漏電流 Black print on the case top. Marking 標示 DRAWING (Unit: mm) *1. Voltage mark for 6.3V is [6V] Within ±10% of initial value 初始值的±10%以内 initial specified value or less 不大於規範值 initial specified value or less 不大於規範值 鋁殼頂部黑字印刷。 外形圖 6.3V 的產品標識為 [6V] DIMENSIONS (Unit: mm) 尺寸表 ∅D x L 4 x 5.4 5 x 5.4 6.3 x 5.4 A B C 1.8 4.3 4.3 1.0 5.4 2.1 5.3 5.3 1.3 5.4 2.4 6.6 6.6 2.2 5.4 E ± 0.2 L NOTE: All designs and specifications are for reference only and are subject to change without prior notice. If any doubt about safety for your application, please contact us immediately for technical assistance before purchase. 注: 以上所提供的設計及特性參數僅供參考，任何修改不作預先通知。如果在使用上有疑問，請在採購前與我們聯繫，以便提供技術上的協助。 SEMTECH ELECTRONICS LTD. (Subsidiary of Sino-Tech International Holdings Limited, a company listed on the Hong Kong Stock Exchange, Stock Code: 724) ® KP Series DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT 規格尺寸及最大允許紋波電流 μF WV 6.3 10 16 25 35 50 Code 代碼 0J 1A 1C 1E 1V 1H 0.1 0R1 4 × 5.4 1.0 0.22 R22 4 × 5.4 2.0 0.33 R33 4 × 5.4 2.8 0.47 R47 4 × 5.4 4.0 1 010 4 × 5.4 8.4 2.2 2R2 3.3 3R3 4.7 4R7 10 100 4 × 5.4 17 22 220 5 × 5.4 28 6.3 × 5.4 33 33 330 6.3 × 5.4 37 6.3 × 5.4 41 6.3 × 5.4 49 47 470 6.3 × 5.4 4 × 5.4 8.4 5 × 5.4 13 5 × 5.4 12 5 × 5.4 16 5 × 5.4 17 12 5 × 5.4 16 5 × 5.4 18 6.3 × 5.4 20 5 × 5.4 23 6.3 × 5.4 27 6.3 × 5.4 29 6.3 × 5.4 37 Case size 尺寸 Ripple current 紋波電流 4 × 5.4 45 yCase size ∅D×L(mm), ripple current (mA rms) at 105°C 120Hz y尺寸∅D×L(mm)，紋波電流(mA rms)於 105°C 120Hz FREQUENCY COEFFICIENT OF ALLOWABLE RIPPLE CURRENT 紋波電流頻率補償系數 Frequency 頻率 50Hz 120Hz 300Hz 1KHz 10KHz~ 系數 0.70 1.00 1.17 1.36 1.50 Coefficient z Taping specifications are given in page 11. 編帶標準請參閱第 11 頁。 z Please refer to page 12 for the minimum package quantity. 最小包裝數量請參閱第 12 頁。 NOTE: All designs and specifications are for reference only and are subject to change without prior notice. If any doubt about safety for your application, please contact us immediately for technical assistance before purchase. 注: 以上所提供的設計及特性參數僅供參考，任何修改不作預先通知。如果在使用上有疑問，請在採購前與我們聯繫，以便提供技術上的協助。 SEMTECH ELECTRONICS LTD. (Subsidiary of Sino-Tech International Holdings Limited, a company listed on the Hong Kong Stock Exchange, Stock Code: 724) ®